AD843KN - 34MHz Fast-Settling CBFET Op Amp | Analog Devices
料号: AD843KN ✓ 量产中AD843KN 概述
A CBFET-input operational amplifier is a voltage-feedback amplifier whose input stage uses current-buffered FET devices. This amplifier category combines very low input bias current with wide bandwidth, placing the AD843KN between general-purpose precision amplifiers and specialist high-speed amplifier families. It is used within broader amplifier, signal-conditioning, and power-management systems where fast response and minimal input loading are more important than rail-to-rail input operation.
The principal features of the AD843KN include 34 MHz unity-gain bandwidth, a 250 V/µs slew rate, and settling to within 0.01% of the final value in 135 ns for a 10 V step. It is stable at gains of one or greater, simplifying unity-gain buffering and noninverting amplifier designs. The typical input bias current is only 0.6 nA, while the maximum input offset voltage for the AD843K family is 1 mV.
The AD843 datasheet describes excellent large-signal behavior and stable unity-gain operation. At a 5 MHz input frequency, the associated switching-device application reports crosstalk of -85 dB and isolation of -75 dB. These figures reflect the switching context rather than a standalone AD843 isolation specification, but they illustrate why the amplifier's bandwidth, input capacitance, and settling behavior must be considered together in fast signal paths.
Typical uses include high-speed sample-and-hold systems, high-speed integrators, active filters, and high-frequency signal-conditioning circuits. The combination of 250 V/µs slew rate and 135 ns settling is particularly useful when the system must recover quickly after a large input transition. The 0.6 nA bias current also makes the device appropriate for sources whose output impedance makes input bias effects significant.
Designers should use stable feedback networks at gains of one or greater, provide adequate supply bypassing, and route sensitive input and feedback connections to minimize parasitic capacitance. The operating supply limits and temperature grade should be checked in the Analog Devices AD843 datasheet before using the amplifier in a new design, especially where the negative supply approaches -5 V.
This product page combines the AD843KN's principal electrical characteristics, package details, application guidance, comparison parameters, and replacement information into an engineering-focused selection resource. It also distinguishes true pin-compatible family variants from alternatives that require a different package or materially different electrical performance.
直接替换替代料: AD843KN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: AD843KN (相同外形与封装尺寸) ——差异在于 Input Bias Current, Input Offset Voltage, Mounting Type, Number of Circuits, Package.
AD843JN
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →AD843K
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD843JR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD843SQ/883B
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →AD843KN 最大额定值与电气特性
| Unity-Gain Bandwidth | 34 MHz |
| Input Bias Current | 0.6 nA typical |
| Settling Time | 135 ns to within 0.01% of final value |
| Settling Test Step | 10 V |
| Slew Rate | 250 V/µs |
| Full-Power Bandwidth | 3.9 MHz |
| Minimum Stable Gain | 1 |
| Input Offset Voltage | 1 mV maximum for AD843K |
| Input Stage Type | CBFET |
| Switching Crosstalk at 5 MHz Input | -85 dB |
| Switching Isolation at 5 MHz Input | -75 dB |
| Maximum Negative Supply in Switching Application | -5 V |
| Number of Amplifiers | 1 amplifier |
| Number of Circuits | 1 circuit |
| 封装 | 8-pin DIP |
| 安装类型 | Through-hole |
AD843KN 8-pin dip 引脚配置指南
AD843KN(8-pin dip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: AD843KN.
请参阅 数据手册 以查看完整引脚配置。
典型应用
AD843KN 适用于 6 应用s: High-Speed Sample-and-Hold, High-Speed Active Filtering, High-Speed Integrator, High-Frequency Signal Conditioning, Precision Pulse and Edge Conditioning, Data-Acquisition Front End.
High-Speed Sample-and-Hold
The AD843KN is well suited to high-speed sample-and-hold signal chains because its 34 MHz unity-gain bandwidth and 250 V/µs slew rate allow the amplifier output to recover rapidly after acquisition. Its 135 ns settling to within 0.01% after a 10 V step is important when the next sample arrives quickly. The 0.6 nA typical input bias current also reduces loading of high-impedance sources, although switch charge injection, hold-capacitor dielectric absorption, and amplifier input capacitance still require separate analysis.
推荐
High-Speed Active Filtering
In an active-filter implementation, the AD843KN provides the bandwidth and slew-rate headroom needed to preserve large or high-frequency signals without excessive distortion. Its unity-gain stability supports buffer and low-gain filter topologies, while the 250 V/µs slew rate helps the output track changing waveforms. Component selection should preserve the intended phase margin because high closed-loop gain, parasitic capacitance, and high-Q filter behavior can reduce stability even when the amplifier is unity-gain stable.
推荐
High-Speed Integrator
The AD843KN can serve as the active element in a high-speed integrator because its 250 V/µs slew rate supports rapid output movement and its 135 ns settling characteristic reduces recovery time. The low 0.6 nA typical input bias current is advantageous when the integration input comes from a high-impedance source. Practical implementations must account for integration-capacitor tolerance, parasitic input capacitance, reset-switch behavior, saturation recovery, and the finite output-voltage range.
推荐
High-Frequency Signal Conditioning
The AD843KN is appropriate for conditioning signals with significant frequency content because its 34 MHz unity-gain bandwidth and 3.9 MHz full-power bandwidth offer useful separation between small-signal bandwidth and large-signal capability. The CBFET input provides 0.6 nA typical bias current, reducing disturbance of sensitive sources. Designers should verify the closed-loop gain response, output-drive requirement, and allowable distortion over the complete input range before placing the device directly after a transducer or high-impedance sensor.
推荐
Precision Pulse and Edge Conditioning
Fast pulse edges can experience amplitude and timing errors if an amplifier slews too slowly, making the AD843KN useful for edge-shaping and pulse-conditioning circuits. Its 250 V/µs slew rate and 135 ns settling to within 0.01% support rapid recovery after large transitions. The 8-pin DIP package also permits straightforward prototyping and replacement in laboratory or legacy equipment, although input protection and supply bypassing remain important when handling fast edges.
推荐
Data-Acquisition Front End
The AD843KN can drive a data-acquisition front end when the source impedance and required settling interval make slower general-purpose amplifiers unsuitable. Its 0.6 nA typical input bias current reduces current-related errors at high-impedance inputs, while 34 MHz bandwidth supports signals well above typical slow ADC sampling rates. The interface should still be evaluated for ADC acquisition time, settling accuracy, source capacitance, clock-edge alignment, and the amplifier's output swing.
推荐
推荐产品汇总
工程参考数据: AD843KN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD843JN | AD843K | AD843JR | AD843SQ/883B |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin DIP | 8-pin DIP | 8-pin DIP | 8-pin DIP | 8-pin DIP |
| Unity-Gain Bandwidth | 34 MHz | 34 MHz | 34 MHz | 34 MHz | 34 MHz |
| Slew Rate | 250 V/µs | 250 V/µs | 250 V/µs | 250 V/µs | 250 V/µs |
| Settling Time | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% |
| Input Bias Current | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical |
| Full-Power Bandwidth | 3.9 MHz | 3.9 MHz | 3.9 MHz | 3.9 MHz | 3.9 MHz |
| Minimum Stable Gain | 1 | 1 | 1 | 1 | 1 |
| Temperature Qualification | K grade | J grade | Base AD843K ordering code | J grade | Military-oriented SQ/883B option |
关键差异点
- Combines very low input bias current with high bandwidth (对比 AD843JN)
- Fast recovery after large input transitions (对比 AD843K)
- Large-signal performance for fast signal paths (对比 AD843JR)
- Same-family option with military-oriented qualification path (对比 AD843SQ/883B)
设计说明
Do not assume that identical package outlines guarantee full interchangeability. Compare the AD843KN and replacement device for input offset limits, temperature grade, supply range, and offset-voltage trim capability. The amplifier is stable at gains of one or greater, so verify the intended closed-loop gain and feedback network against the manufacturer's gain-bandwidth and stability plots before modifying an existing board.
Keep the input and feedback traces short, and place feedback components close to the amplifier pins. High-speed operation makes PCB capacitance and inductance significant, particularly around the input, feedback node, and power pins. Use a continuous ground-return path and minimize shared impedance between input-referenced and output currents. Avoid long stubs or test-point branches on sensitive analog nodes.
Place the supply-bypass capacitors close to the power pins and provide adequate decoupling for the expected load transients. The AD843 family's 250 V/µs slew rate can demand rapid output-current changes, so supply wiring and grounding should not introduce glitches into the signal path. Confirm the actual output swing, load, and dissipation under worst-case operating conditions using the datasheet's recommended supply arrangement.
合规信息
The Analog Devices AD843 documentation identifies the amplifier and its electrical characteristics but does not establish every material-compliance declaration for the exact AD843KN ordering code.