AD843KN - 34MHz Fast-Settling CBFET Op Amp | Analog Devices
부품 번호: AD843KN ✓ 활성AD843KN 개요
A CBFET-input operational amplifier is a voltage-feedback amplifier whose input stage uses current-buffered FET devices. This amplifier category combines very low input bias current with wide bandwidth, placing the AD843KN between general-purpose precision amplifiers and specialist high-speed amplifier families. It is used within broader amplifier, signal-conditioning, and power-management systems where fast response and minimal input loading are more important than rail-to-rail input operation.
The principal features of the AD843KN include 34 MHz unity-gain bandwidth, a 250 V/µs slew rate, and settling to within 0.01% of the final value in 135 ns for a 10 V step. It is stable at gains of one or greater, simplifying unity-gain buffering and noninverting amplifier designs. The typical input bias current is only 0.6 nA, while the maximum input offset voltage for the AD843K family is 1 mV.
The AD843 datasheet describes excellent large-signal behavior and stable unity-gain operation. At a 5 MHz input frequency, the associated switching-device application reports crosstalk of -85 dB and isolation of -75 dB. These figures reflect the switching context rather than a standalone AD843 isolation specification, but they illustrate why the amplifier's bandwidth, input capacitance, and settling behavior must be considered together in fast signal paths.
Typical uses include high-speed sample-and-hold systems, high-speed integrators, active filters, and high-frequency signal-conditioning circuits. The combination of 250 V/µs slew rate and 135 ns settling is particularly useful when the system must recover quickly after a large input transition. The 0.6 nA bias current also makes the device appropriate for sources whose output impedance makes input bias effects significant.
Designers should use stable feedback networks at gains of one or greater, provide adequate supply bypassing, and route sensitive input and feedback connections to minimize parasitic capacitance. The operating supply limits and temperature grade should be checked in the Analog Devices AD843 datasheet before using the amplifier in a new design, especially where the negative supply approaches -5 V.
This product page combines the AD843KN's principal electrical characteristics, package details, application guidance, comparison parameters, and replacement information into an engineering-focused selection resource. It also distinguishes true pin-compatible family variants from alternatives that require a different package or materially different electrical performance.
드롭인 대체품: AD843KN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AD843KN (동일 폼 팩터 및 풋프린트) — 차이점: Input Bias Current, Input Offset Voltage, Mounting Type, Number of Circuits, Package.
AD843JN
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →AD843K
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD843JR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD843SQ/883B
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →AD843KN 최대 정격 & 전기적 특성
| Unity-Gain Bandwidth | 34 MHz |
| Input Bias Current | 0.6 nA typical |
| Settling Time | 135 ns to within 0.01% of final value |
| Settling Test Step | 10 V |
| Slew Rate | 250 V/µs |
| Full-Power Bandwidth | 3.9 MHz |
| Minimum Stable Gain | 1 |
| Input Offset Voltage | 1 mV maximum for AD843K |
| Input Stage Type | CBFET |
| Switching Crosstalk at 5 MHz Input | -85 dB |
| Switching Isolation at 5 MHz Input | -75 dB |
| Maximum Negative Supply in Switching Application | -5 V |
| Number of Amplifiers | 1 amplifier |
| Number of Circuits | 1 circuit |
| 패키지 | 8-pin DIP |
| 실장 유형 | Through-hole |
AD843KN 8-pin dip 핀 구성 가이드
AD843KN(8-pin dip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD843KN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD843KN 적합 용도: 6 애플리케이션s: High-Speed Sample-and-Hold, High-Speed Active Filtering, High-Speed Integrator, High-Frequency Signal Conditioning, Precision Pulse and Edge Conditioning, Data-Acquisition Front End.
High-Speed Sample-and-Hold
The AD843KN is well suited to high-speed sample-and-hold signal chains because its 34 MHz unity-gain bandwidth and 250 V/µs slew rate allow the amplifier output to recover rapidly after acquisition. Its 135 ns settling to within 0.01% after a 10 V step is important when the next sample arrives quickly. The 0.6 nA typical input bias current also reduces loading of high-impedance sources, although switch charge injection, hold-capacitor dielectric absorption, and amplifier input capacitance still require separate analysis.
추천
High-Speed Active Filtering
In an active-filter implementation, the AD843KN provides the bandwidth and slew-rate headroom needed to preserve large or high-frequency signals without excessive distortion. Its unity-gain stability supports buffer and low-gain filter topologies, while the 250 V/µs slew rate helps the output track changing waveforms. Component selection should preserve the intended phase margin because high closed-loop gain, parasitic capacitance, and high-Q filter behavior can reduce stability even when the amplifier is unity-gain stable.
추천
High-Speed Integrator
The AD843KN can serve as the active element in a high-speed integrator because its 250 V/µs slew rate supports rapid output movement and its 135 ns settling characteristic reduces recovery time. The low 0.6 nA typical input bias current is advantageous when the integration input comes from a high-impedance source. Practical implementations must account for integration-capacitor tolerance, parasitic input capacitance, reset-switch behavior, saturation recovery, and the finite output-voltage range.
추천
High-Frequency Signal Conditioning
The AD843KN is appropriate for conditioning signals with significant frequency content because its 34 MHz unity-gain bandwidth and 3.9 MHz full-power bandwidth offer useful separation between small-signal bandwidth and large-signal capability. The CBFET input provides 0.6 nA typical bias current, reducing disturbance of sensitive sources. Designers should verify the closed-loop gain response, output-drive requirement, and allowable distortion over the complete input range before placing the device directly after a transducer or high-impedance sensor.
추천
Precision Pulse and Edge Conditioning
Fast pulse edges can experience amplitude and timing errors if an amplifier slews too slowly, making the AD843KN useful for edge-shaping and pulse-conditioning circuits. Its 250 V/µs slew rate and 135 ns settling to within 0.01% support rapid recovery after large transitions. The 8-pin DIP package also permits straightforward prototyping and replacement in laboratory or legacy equipment, although input protection and supply bypassing remain important when handling fast edges.
추천
Data-Acquisition Front End
The AD843KN can drive a data-acquisition front end when the source impedance and required settling interval make slower general-purpose amplifiers unsuitable. Its 0.6 nA typical input bias current reduces current-related errors at high-impedance inputs, while 34 MHz bandwidth supports signals well above typical slow ADC sampling rates. The interface should still be evaluated for ADC acquisition time, settling accuracy, source capacitance, clock-edge alignment, and the amplifier's output swing.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD843KN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AD843JN | AD843K | AD843JR | AD843SQ/883B |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin DIP | 8-pin DIP | 8-pin DIP | 8-pin DIP | 8-pin DIP |
| Unity-Gain Bandwidth | 34 MHz | 34 MHz | 34 MHz | 34 MHz | 34 MHz |
| Slew Rate | 250 V/µs | 250 V/µs | 250 V/µs | 250 V/µs | 250 V/µs |
| Settling Time | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% | 135 ns to within 0.01% |
| Input Bias Current | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical | 0.6 nA typical |
| Full-Power Bandwidth | 3.9 MHz | 3.9 MHz | 3.9 MHz | 3.9 MHz | 3.9 MHz |
| Minimum Stable Gain | 1 | 1 | 1 | 1 | 1 |
| Temperature Qualification | K grade | J grade | Base AD843K ordering code | J grade | Military-oriented SQ/883B option |
주요 차별점
- Combines very low input bias current with high bandwidth (vs AD843JN)
- Fast recovery after large input transitions (vs AD843K)
- Large-signal performance for fast signal paths (vs AD843JR)
- Same-family option with military-oriented qualification path (vs AD843SQ/883B)
설계 노트
Do not assume that identical package outlines guarantee full interchangeability. Compare the AD843KN and replacement device for input offset limits, temperature grade, supply range, and offset-voltage trim capability. The amplifier is stable at gains of one or greater, so verify the intended closed-loop gain and feedback network against the manufacturer's gain-bandwidth and stability plots before modifying an existing board.
Keep the input and feedback traces short, and place feedback components close to the amplifier pins. High-speed operation makes PCB capacitance and inductance significant, particularly around the input, feedback node, and power pins. Use a continuous ground-return path and minimize shared impedance between input-referenced and output currents. Avoid long stubs or test-point branches on sensitive analog nodes.
Place the supply-bypass capacitors close to the power pins and provide adequate decoupling for the expected load transients. The AD843 family's 250 V/µs slew rate can demand rapid output-current changes, so supply wiring and grounding should not introduce glitches into the signal path. Confirm the actual output swing, load, and dissipation under worst-case operating conditions using the datasheet's recommended supply arrangement.
규정 준수 정보
The Analog Devices AD843 documentation identifies the amplifier and its electrical characteristics but does not establish every material-compliance declaration for the exact AD843KN ordering code.