EP1S60F1020C6N - Stratix FPGA, 57K Logic Elements, FBGA-1020 | Intel
料号： EP1S60F1020C6N ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $285 | $285.00 |
| 10 | $265 | $2,650.00 |
| 100 | $240 | $24,000.00 |
| 500 | $215 | $107,500.00 |
| 1,000 | $195 | $195,000.00 |
EP1S60F1020C6N 概述
What is a Stratix FPGA? The Stratix family is Intel/Altera's high-density programmable logic family built on a register-rich, LUT-based fabric with embedded TriMatrix memory blocks, DSP blocks, and high-speed I/O. It sits in the broader hierarchy of programmable logic devices (PLD) -> FPGA -> high-performance FPGA, and historically served applications that demanded high logic density and DSP throughput before later Stratix and Cyclone families replaced it.
Key features include 12 dedicated clock pins and up to 80 global clock networks, embedded memory organized in three block sizes (M512, M4K, M-RAM), 12 PLLs with up to 800 MHz operation, support for external memory interfaces including DDR SDRAM, FCRAM, QDR SRAM, and SDR SDRAM, and high-speed LVDS I/O capable of up to 840 Mbps. The C6 speed grade represents a mid-tier timing closure option within the Stratix lineup.
Architecture-wise, the device integrates a LAB/ALM-style adaptive logic module fabric, dedicated DSP blocks for 9x9, 18x18, and 36x36 signed/unsigned multiplication with accumulation, and a high-speed interconnect routing network. The 'N' suffix indicates lead-free / Pb-free termination. The F1020 package variant provides the highest I/O count in the EP1S60 line.
Typical applications include 10G/40G telecom line cards, software-defined radio (SDR) baseband, high-definition video processing, ASIC prototyping, and high-performance DSP firmware acceleration in defense, medical imaging, and broadcast equipment. The wide embedded multiplier count (773) and large TriMatrix memory (5.2 Mbits) make it especially attractive for FFT, FIR filter, and Reed-Solomon forward error correction engines.
Design consideration: ensure proper decoupling with multiple 0.1 µF and 10 µF capacitors around the power balls, follow the Intel Stratix pin connection guidelines for JTAG, MSEL configuration mode pins, and respect VCCINT/VCCIO plane separation. PCB designers should allocate at least 12 routing layers for the 1020-ball FBGA escape, with 1 oz copper for power and 0.5 oz for signals. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone datasheet.
直接替换替代料： EP1S60F1020C6N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： EP1S60F1020C6N （相同外形与封装尺寸） ——差异在于 Package, Speed Grade, Family, Operating Temperature, Process Technology.
快速对比工具——选择替代料号进行并排对比：
EP1S60F1020C5N
✅ 直接替换✓ 有现货
$2050 / 个
查看数据手册 →EP1S60F1020C6
✅ 直接替换✓ 有现货
$105 / 个
查看数据手册 →EP1S60F1020C5
✅ 直接替换✓ 有现货
$171 / 个
查看数据手册 →EP1S60F1020I6N
✅ 直接替换✓ 有现货
$3650 / 个
查看数据手册 →EP1S40F1020C6N
✅ 直接替换✓ 有现货
$695 / 个
查看数据手册 →EP1S60F1020C6N 最大额定值与电气特性
| Series | Stratix |
| Family | Stratix (EP1S) |
| Logic Elements (LEs) | 57,120 |
| Logic Cells | 6,570 blocks (per chipdig datasheet summary) |
| Embedded RAM (Total Bits) | 5,215,104 bits |
| Embedded Multipliers | 773 (18x18) |
| Maximum User I/O Pins | Per datasheet, package-dependent (F1020 variant) |
| Package Type | 1020-ball FBGA (FineLine BGA), 33 x 33 mm, 1 mm pitch |
| Logic Family / Process | CMOS, 0.13 µm |
| 工作温度 | 0°C to +85°C (Commercial) |
| 电源电压 | Per datasheet (Stratix Device Handbook Vol. 1) |
| Speed Grade | C6 (mid-tier) |
| Lead-Free / Pb-Free | Yes (suffix 'N') |
| RoHS 状态 | Compliant (per 'N' suffix) |
| 安装类型 | Surface Mount (BGA) |
| Configuration | JTAG / Passive Serial / Fast Passive Parallel via MSEL pins |
| PLL Count | 12 (per Stratix family datasheet) |
| Memory Block Types | TriMatrix (M512, M4K, M-RAM) |
EP1S60F1020C6N 1020-ball fbga (fineline bga), 33 x 33 mm, 1 mm pitch 引脚配置指南
EP1S60F1020C6N（1020-ball fbga (fineline bga), 33 x 33 mm, 1 mm pitch 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： EP1S60F1020C6N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
EP1S60F1020C6N 适用于 6 应用s: 10G/40G Telecom Line Card Processing, Software Defined Radio (SDR) Baseband, High-Definition Video Processing, ASIC Prototyping and Emulation, Medical Imaging Reconstruction, Industrial Automation Motion Control.
10G/40G Telecom Line Card Processing
The EP1S60F1020C6N fits 10G/40G telecom line card processing because its 57,120 logic elements, 5.2 Mbits of TriMatrix embedded RAM, and 773 18x18 multipliers deliver the throughput required for packet classification, traffic management, and forward error correction. The 12 PLLs and high-speed LVDS I/O (up to 840 Mbps per channel) enable clean clocking of multi-rate SerDes and switch-fabric interfaces. Placed on a line card between the network processor and the framer, the part performs layer-2/3 header parsing and Reed-Solomon FEC at line rate. The trade-off versus an ASIC is lower per-unit throughput but much faster NRE turnaround for evolving protocol standards like OTU2 and FlexE.
推荐
Software Defined Radio (SDR) Baseband
The EP1S60F1020C6N is well suited to SDR baseband processing, where its 773 dedicated 18x18 multipliers and large embedded memory deliver the FIR filter taps, FFT butterfly operations, and channelization buffers required for wideband digital down-conversion. Combined with external high-speed ADCs and DACs, the device can implement 100+ MHz instantaneous bandwidth waveforms such as LTE, WiMAX, or proprietary military waveforms. The TriMatrix M-RAM blocks (512 Kbit each) are ideal for storing FFT window coefficients. Unlike a DSP processor, the FPGA achieves deterministic latency critical for TDD half-duplex switching, at the cost of higher power consumption.
推荐
High-Definition Video Processing
The EP1S60F1020C6N suits high-definition video processing pipelines including 1080p60 broadcast format conversion, scaling, deinterlacing, and color-space conversion. Its 5.2 Mbits of embedded RAM holds multiple video line buffers (M4K and M-RAM blocks) needed for 2D FIR filtering and motion-adaptive deinterlacing, while the 773 multipliers handle polyphase scaler taps at full HD rates. The high LVDS bandwidth is sufficient for dual-channel DVI/HDMI input bridges at 1.65 Gbps per link. Designers pair this part with external DDR SDRAM for frame store and use the Stratix ALM fabric for the scaler state machine.
推荐
ASIC Prototyping and Emulation
The EP1S60F1020C6N is frequently used in ASIC prototyping platforms where its 57K LEs and abundant multipliers map a sizeable portion of a mid-complexity ASIC block. Multiple Stratix FPGAs can be cascaded via LVDS to emulate multi-million-gate ASICs, with the JTAG chain providing unified programming. The embedded TriMatrix memory and PLL count permit accurate emulation of clock trees and SRAM macros. Compared with dedicated emulation systems like Cadence Palladium, the Stratix array offers lower per-cycle cost but slower debug visibility. Designers map timing-critical paths first and use TimeQuest SDC constraints to verify setup/hold across the array.
推荐
Medical Imaging Reconstruction
The EP1S60F1020C6N fits medical imaging reconstruction algorithms such as CT filtered back-projection and MRI FFT-based reconstruction. The 773 multipliers perform parallel ray summation and voxel interpolation at diagnostic frame rates, while the embedded memory buffers 512x512 image slices with sufficient bandwidth. The commercial temperature range (0 to +85°C) is adequate for controlled-room imaging cabinets, though the EP1S60F1020I6N variant should be selected for mobile cart or bedside platforms. Compared with GPU implementations, the FPGA delivers deterministic per-patient scan latency, critical for synchronized X-ray source triggering.
推荐
Industrial Automation Motion Control
The EP1S60F1020C6N supports industrial automation motion control with multi-axis servo loops and high-speed deterministic response. The 57K LEs handle PID loops for 16+ axes simultaneously at 32 kHz loop rates, while the LVDS I/O interfaces directly to resolver-to-digital converters and incremental encoder inputs. The 12 PLLs generate synchronized PWMs for IGBT-based motor drivers and the TriMatrix memory stores trajectory tables. The 1020-ball BGA provides sufficient user I/O for parallel axis expansion. Compared with a microcontroller, the FPGA delivers deterministic multi-axis latency below 1 µs at the cost of higher quiescent power.
推荐
推荐产品汇总
工程参考数据： EP1S60F1020C6N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | EP1S60F1020C5N | EP1S60F1020C6 | EP1S60F1020C5 | EP1S60F1020I6N | EP1S40F1020C6N |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | FBGA-1020 (33x33 mm, 1 mm pitch) | FBGA-1020 - same | FBGA-1020 - same | FBGA-1020 - same | FBGA-1020 - same | FBGA-1020 - same (verify I/O mapping) |
| Logic Elements | 57,120 | 57,120 (same) | 57,120 (same) | 57,120 (same) | 57,120 (same) | ~41,250 (-28%) |
| Embedded RAM (bits) | 5,215,104 | 5,215,104 (same) | 5,215,104 (same) | 5,215,104 (same) | 5,215,104 (same) | 3,423,744 (-34%) |
| Embedded Multipliers (18x18) | 773 | 773 (same) | 773 (same) | 773 (same) | 773 (same) | 448 (-42%) |
| Speed Grade | C6 (commercial) | C5 (slower) | C6 (same) | C5 (slower) | I6 (industrial) | C6 (same) |
| Operating Temperature | 0°C to +85°C (Commercial) | 0°C to +85°C (Commercial) | 0°C to +85°C (Commercial) | 0°C to +85°C (Commercial) | -40°C to +100°C (Industrial) | 0°C to +85°C (Commercial) |
| Lead-Free (Pb-Free) | Yes (N suffix) | Yes | No (leaded) | No (leaded) | Yes | Yes |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
关键差异点
- C6 speed grade offers higher Fmax than the C5 variant for timing-critical DSP paths （对比 EP1S60F1020C5N)
- Lead-free (Pb-free) termination suitable for RoHS-compliant assemblies （对比 EP1S60F1020C6)
- Full 57,120-LE density vs 41,250 LEs in the EP1S40 package twin （对比 EP1S40F1020C6N)
设计说明
Estimated: At typical Stratix EP1S60 utilization of 70% LEs and 50% RAM switching at 200 MHz, total power consumption is approximately 4-6 W. Decouple all VCCINT balls with 0.1 µF X7R ceramics placed within 50 mils of each ball cluster, and add four bulk 220 µF tantalum capacitors around the package perimeter. Separate VCCINT and VCCIO planes must be split under the BGA escape to avoid simultaneous switching noise coupling into the core logic. Follow the Stratix Device Handbook PowerPlay section for accurate early-stage power estimation.
The 1020-ball FBGA at 1 mm pitch requires at least 12 PCB layers with 1 oz copper power planes. Use laser-drilled microvias (4-6 mil pad) with 0.5 oz signal layers and 1 oz power/ground layers. Fan-out routing should follow a dog-bone or via-in-pad escape pattern, and all 1020 balls should be connected with 0.5 oz copper traces minimum. Reference Intel AN-224 (Stratix Board Design Guidelines) for via-in-pad recommendations and matched-length LVDS pair routing within 5 mil tolerance.
Three common pitfalls when bringing up the EP1S60F1020C6N: (1) leaving MSEL configuration pins floating - they MUST be tied high or low per the desired configuration mode (AS, PS, JTAG); (2) using a non-1.8V VCCPD supply with the wrong JTAG voltage causing programming failure - verify VCCPD matches the I/O bank reference; (3) ignoring nCONFIG and nSTATUS reset sequencing - hold nCONFIG low for at least 2 µs after power stable. Always use the latest Quartus II Service Pack and the matching BSDL file for boundary-scan testing.
Estimated: At 5 W dissipation and the FBGA-1020 theta-JA of approximately 12-15 °C/W (still air, JEDEC 4-layer board), junction-to-ambient rise is 60-75 °C. For commercial-temperature (0-85°C) operation, internal junction temperature must remain below 85°C, so ambient must stay under 10-25°C without airflow. Add 200 LFM forced-air cooling, or a heat spreader (e.g., 30 x 30 mm copper pad bonded to the BGA top with thermal epoxy), to keep junction below 100°C. For industrial applications using the EP1S60F1020I6N variant, thermal headroom is even tighter.
合规信息
RoHS compliance inferred from 'N' suffix per Altera/Intel legacy packaging convention. REACH, halogen-free, and conflict-minerals status not stated in verified data and should be requested from the supplier. AEC-Q100 not applicable - this is an FPGA, not an automotive-grade IC.
