M25P16-VMN6P - 16Mb SPI NOR Flash 75MHz SOIC-8 | Micron
料号： M25P16-VMN6P ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $1.85 | $1.85 |
| 10 | $1.62 | $16.20 |
| 100 | $1.34 | $134.00 |
| 500 | $1.15 | $575.00 |
| 1,000 | $0.98 | $980.00 |
| 3,000 | $0.82 | $2,460.00 |
M25P16-VMN6P 概述
A NOR Flash memory is a non-volatile storage technology that retains data without power and supports random (byte-level) read access, unlike NAND Flash which is read sequentially by page. The NOR architecture makes it ideal for code storage and execute-in-place (XIP) boot ROM applications where deterministic, low-latency reads are required at system power-up. The SPI (Serial Peripheral Interface) bus reduces pin count versus parallel NOR, allowing the device to share a 4-wire (or 3-wire) bus with other peripherals and saving PCB area in compact embedded designs.
Key specifications include a 75 MHz SPI clock (50 MHz for legacy read commands), 32-Kbyte and 64-Kbyte sector architecture, JEDEC 2-byte electronic signature, and an industry-standard command set compatible with many prior-generation SPI Flash devices. The 8-pin SOIC package provides 3 mm x 4.9 mm board area, supporting both commercial (0 C to 70 C) and industrial (-40 C to +85 C) operating ranges.
The M25P16 architecture uses a single 2.7-3.6 V supply, on-chip write/erase voltage generation, and a deep power-down mode drawing typically 1 uA for battery-backed applications. Hardware sector protection and software block-lock bits allow designers to enforce bootloader read-only zones for secure firmware-update implementations.
Typical applications include router firmware storage, IoT sensor node boot memory, set-top box data logging, industrial PLC parameter storage, and consumer electronics such as printers and smart-home gateways where small-footprint code and parameter storage is required. Compared to EEPROM, NOR Flash provides higher density per die at lower cost per Mbit but requires block-level erase before write.
When designing with this device, ensure VCC decoupling of 100 nF plus 4.7 uF is placed within 5 mm of the VCC pin to suppress write/erase inrush transients. The /WP and /HOLD pins must be tied to VCC (or pulled high) if unused, and the /CS line must be returned to logic high between commands to reset the SPI state machine.
直接替换替代料： M25P16-VMN6P ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： M25P16-VMN6P （相同外形与封装尺寸） ——差异在于 Memory Type, Package, Interface, Memory Size, Operating Temperature.
快速对比工具——选择替代料号进行并排对比：
M25P16-VMN6PBA
✅ 直接替换📋 参考替代料（不在目录中）
M25PX16-VMN6P
✅ 直接替换📋 参考替代料（不在目录中）
W25Q16JVSNIQ
✅ 直接替换📋 参考替代料（不在目录中）
MX25L1606EM2I-12G
✅ 直接替换📋 参考替代料（不在目录中）
GD25Q16CEIG
✅ 直接替换📋 参考替代料（不在目录中）
M25P16-VMN6P 最大额定值与电气特性
| 存储器类型 | NOR Flash |
| 存储容量 | 16 Mbit (2 Mbit x 8) |
| 接口 | SPI (Serial Peripheral Interface) |
| 最大时钟频率 | 75 MHz |
| Supply Voltage (VCC) | 2.7 V to 3.6 V |
| Page Size | 256 bytes |
| Sector Size | 64 KB (with 32 KB sub-sector option) |
| Program Time (per page) | 1.4 ms typical |
| Sector Erase Time | 0.65 s typical |
| Bulk Erase Time | 4 s typical |
| 工作温度 | -40 C to +85 C (industrial grade) |
| 封装 | 8-pin SOIC (SO8) |
| 引脚数量 | 8 |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
| End-of-Life Status | EOL - last time buy announced by Micron; migrate to M25P16-VMN6PBA or successor families |
M25P16-VMN6P 引脚配置
| 引脚 1 | /CS — Chip select, active low - enables SPI communication |
| 引脚 2 | DO (SO) — Serial data out (MISO) - driven by the Flash during reads |
| 引脚 3 | /WP — Write protect, active low - hardware lock for status register writes |
| 引脚 4 | GND — Ground reference |
| 引脚 5 | DI (SI) — Serial data in (MOSI) - command, address, and data input |
| 引脚 6 | SCK — Serial clock from the master, up to 75 MHz |
| 引脚 7 | /HOLD — Hold, active low - pauses serial communication without resetting |
| 引脚 8 | VCC — Power supply, 2.7 V to 3.6 V |
典型应用
M25P16-VMN6P 适用于 7 应用s: Router / Gateway Firmware Storage, IoT Sensor Node Boot Memory, Industrial PLC Parameter Storage, Set-Top Box Data Logging, Consumer Printer Firmware, Smart Home Gateway, Automotive Infotainment Boot Memory.
Router / Gateway Firmware Storage
The M25P16-VMN6P suits router and gateway firmware storage where deterministic code shadowing from SPI to RAM is required at boot. Its 16 Mbit density holds a complete Linux kernel plus rootfs, and the 75 MHz SPI clock enables 9.375 MB/s read throughput for fast boot. Unlike NAND, NOR's byte-addressable reads allow execute-in-place (XIP) directly from the Flash if the host CPU supports SPI-XIP, reducing RAM footprint. The industrial temperature grade supports outdoor CPE installations.
推荐
IoT Sensor Node Boot Memory
In IoT sensor nodes, the M25P16-VMN6P stores bootloader, application firmware, and persistent configuration across power cycles. The 2.7 V minimum supply matches coin-cell or Li-Ion battery rails, and the deep power-down mode drawing 1 uA typical extends battery life in sleep. Its hardware /WP pin protects bootloader sectors from accidental overwrite during field firmware updates, and the 100k endurance cycles per sector comfortably exceeds yearly OTA update schedules for sensor deployments.
推荐
Industrial PLC Parameter Storage
The M25P16-VMN6P fits industrial PLC parameter storage where calibration coefficients, recipe data, and event logs must survive brown-outs and long field lifetimes. Its 20-year data retention and 100k program/erase cycles per sector support decades of industrial service. The hardware /WP pin can be tied to a supervisory reset circuit to block writes during voltage sag, while 32 KB sub-sector erase enables efficient parameter updates without erasing adjacent data.
推荐
Set-Top Box Data Logging
Set-top boxes benefit from the M25P16-VMN6P's 16 Mbit density for storing boot logos, channel lists, and DRM certificates. The SPI interface shares pins with other peripherals like the demodulator and HDMI controller, simplifying PCB routing. Bulk erase in 4 s and page program in 1.4 ms provide reasonable throughput for occasional firmware updates delivered via broadcast or Ethernet.
推荐
Consumer Printer Firmware
Inkjet and laser printers use the M25P16-VMN6P to store firmware, font tables, and printer status logs. Its 256-byte page size aligns with typical font block sizes, allowing fast incremental updates during factory calibration. The 8-pin SOIC footprint sits easily beside the main SoC with minimal PCB area impact, and the wide 2.7-3.6 V supply tolerates USB-powered designs.
推荐
Smart Home Gateway
Smart-home gateways use the M25P16-VMN6P for Z-Wave/Zigbee stack firmware, device pairing tables, and event logs. The industrial temperature grade handles attic or basement installation environments, and the deep power-down mode preserves battery backup during outages. SPI shares the bus with the wireless transceiver, reducing GPIO count on the gateway MCU.
推荐
Automotive Infotainment Boot Memory
Although the standard M25P16-VMN6P is commercial/industrial grade, it is widely used in non-safety automotive infotainment head units and cluster displays where AEC-Q100 is not mandatory. Its 75 MHz SPI supports quick boot of HMI images from Flash to display controller, and the wide voltage range tolerates load-dump transients on the 12 V battery rail downstream of the regulator.
推荐
推荐产品汇总
工程参考数据： M25P16-VMN6P ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | M25P16-VMN6PBA | M25PX16-VMN6P | W25Q16JVSNIQ | MX25L1606EM2I-12G | GD25Q16CEIG |
|---|---|---|---|---|---|---|
| Brand | Micron Technology | Micron Technology | Micron Technology | Winbond | Macronix | GigaDevice |
| Package | 8-pin SOIC (SO8) | 8-pin SOIC (SO8) - same | 8-pin SOIC (SO8) - same | 8-pin SOIC (SO8) - same | 8-pin SOIC (SO8) - same | 8-pin SOIC (SO8) - same |
| Density | 16 Mbit | 16 Mbit | 16 Mbit | 16 Mbit | 16 Mbit | 16 Mbit |
| Maximum SPI Clock | 75 MHz | 75 MHz | 75 MHz | 133 MHz | 86 MHz | 80 MHz |
| Quad-SPI Support | No (standard SPI only) | No | Yes (dual and quad I/O) | Yes (quad-SPI) | Yes (quad-SPI) | Yes (quad-SPI) |
| Supply Voltage | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V | 2.7 V to 3.6 V |
| Sector Architecture | 64 KB sectors with 32 KB sub-sector | 64 KB / 32 KB | 64 KB / 32 KB | 4 KB / 32 KB / 64 KB | 4 KB sub-sector + 64 KB sector | 4 KB sub-sector + 32/64 KB sector |
| Page Program Time (typ) | 1.4 ms (256 B) | 1.4 ms (256 B) | 1.4 ms (256 B) | 0.5 ms (256 B) | 0.7 ms (256 B) | 0.6 ms (256 B) |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lifecycle Status | EOL (last time buy) | Active | EOL | Active | Active | Active |
关键差异点
- Industry-standard 75 MHz SPI bus with Micron-proven command set （对比 W25Q16JVSNIQ)
- Single-supply 2.7 V to 3.6 V operation with internal charge pump （对比 M25PX16-VMN6P)
- Hardware /WP and /HOLD pins for system-level protection （对比 GD25Q16CEIG)
设计说明
Provide a 100 nF X7R ceramic capacitor plus a 4.7 uF X5R bulk capacitor within 5 mm of the VCC pin to decouple write/erase inrush currents. The on-chip charge pump draws brief bursts during sector erase; an undersized bulk cap can cause VCC droop that triggers spurious watchdog resets. Tie /CS high during VCC ramp-up to keep the device in standby mode.
Route SPI traces (SCK, SI, SO, /CS) as a matched-length group with 50 ohm characteristic impedance and keep total trace length under 50 mm at 75 MHz. Place a 22-33 ohm series resistor near the master SCK output to dampen reflections. Keep the Flash away from switching DC-DC converters and route the VCC trace with a star topology from the LDO output to minimize noise coupling.
Do not leave /WP or /HOLD floating; both must be tied high through 10 kohm pull-ups to VCC if unused. Floating inputs can pick up noise and inadvertently lock the status register or pause the SPI state machine. Verify the Read-ID command (0x9F) returns JEDEC ID 0x20 0x15 0x15 (Micron M25P16) before issuing any other command to confirm bus integrity.
At 75 MHz SCK, the SO output rise/fall time should be checked against the master MCU's setup-and-hold requirements. If the master samples SO too close to the SCK edge, insert a small series resistor (10-22 ohm) at SO to slow the edge. Place a ground guard trace between SO and SCK to reduce crosstalk on long bus runs.
合规信息
RoHS and REACH compliant per Micron product page. Standard M25P16-VMN6P is not AEC-Q100 qualified; choose automotive-grade variants separately for safety applications. Halogen-free per JEDEC JS709.
