MAX232BEAWE+ - 2/2 RS-232 Transceiver | Analog Devices
料号: MAX232BEAWE+ ✓ 量产中MAX232BEAWE+ 概述
An RS-232 transceiver is a signal-conversion device used to bridge the logic-voltage domain of a microcontroller, computer, or programmable controller and the voltage-domain requirements of an RS-232 port. Within the interface IC hierarchy, the MAX232BEAWE+ belongs to the RS-232 transceiver class of serial-interface ICs. Its two-driver, two-receiver arrangement suits point-to-point serial links that require bidirectional communication but do not need the larger channel count of a four-driver, four-receiver RS-232 implementation.
The principal benefits are functional integration and compact PCB occupancy. Two transmit channels and two receive channels share one 16-pin SOIC package, while integrated level translation allows the same IC to support both RS-232 output and input signals. The package is suitable for conventional surface-mount PCB assembly, and the + suffix identifies the manufacturer's lead-free commercial ordering configuration. Because the MAX232 family is widely used in RS-232 equipment, designers can generally simplify firmware changes by treating the transceiver as a transparent UART-to-RS-232 interface.
RS-232 transmitters require more voltage and current than ordinary CMOS or bipolar logic outputs. The MAX232BEAWE+ therefore functions as an interface boundary rather than as a general-purpose logic driver. Its internal charge-pump circuitry creates the bipolar voltage used by the drivers, while the receivers convert incoming RS-232 signals to a compatible logic level. This division of responsibilities allows the connected UART controller to operate with ordinary push-pull or open-drain interface circuitry while the cable side uses RS-232 levels.
Typical uses include industrial serial-control equipment, test and measurement instruments, data-acquisition systems, configuration ports, and legacy service interfaces. A two-channel implementation can support one bidirectional communications path with an additional transmitter or receiver when directional requirements differ. It is also appropriate for embedded systems that retain an RS-232 port for compatibility with printers, scanners, controllers, or laboratory equipment even when the rest of the product uses modern digital interfaces.
PCB implementation should follow the Analog Devices MAX232 datasheet for charge-pump capacitor placement, signal routing, and grounding. Keep the charge-pump capacitor connections short, provide the required ceramic capacitance close to the device, and route RS-232 driver outputs away from sensitive receiver inputs. Confirm the connector, cable, grounding, and logic levels before releasing the PCB because the IC solves voltage translation but does not define the complete RS-232 physical interface.
This page combines the exact MAX232BEAWE+ package and interface configuration with same-family drop-in options, application guidance, comparison parameters, and practical RS-232 layout considerations. The alternatives are separated from cross-package designs so an engineer can focus on parts that preserve the 16-pin SOIC footprint.
直接替换替代料: MAX232BEAWE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232BEAWE+ (相同外形与封装尺寸) ——差异在于 Product Type, Interface Standard, Maximum Data Rate, Transceiver Configuration, Supply Voltage.
MAX232ESE+T
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232BAWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232AEWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ACWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232EWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232BEAWE+ 规格参数
| Transceiver Configuration | 2/2 |
| Driver Count | 2 drivers |
| Receiver Count | 2 receivers |
| Interface Standard | RS-232 |
| 封装 | 16-pin SOIC |
| 引脚数量 | 16 pins |
| 安装类型 | Surface mount |
MAX232BEAWE+ 16-pin soic 引脚配置指南
MAX232BEAWE+(16-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232BEAWE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232BEAWE+ 适用于 6 应用s: Industrial Serial-Control Interface, Test and Measurement Equipment, Data-Acquisition System, Legacy Printer and Scanner Interface, Configuration Port for Embedded Equipment, Security and Access-Control Equipment.
Industrial Serial-Control Interface
The MAX232BEAWE+ fits industrial equipment that retains an RS-232 service or control port while using a modern UART controller. Its two drivers and two receivers can support one bidirectional channel plus an additional directional signal pair, and the 16-pin SOIC keeps the interface compact. The IC handles the logic-to-RS-232 voltage conversion in one package, reducing the number of discrete level-shifters required. For deployment, verify the specified temperature range, design the charge-pump capacitor network according to the MAX232 datasheet, and use a suitable industrial connector. The surrounding controller still needs UART configuration, while the MAX232BEAWE+ provides the physical electrical boundary to the RS-232 cable.
推荐
Test and Measurement Equipment
Test instruments, programmable power supplies, and laboratory controllers often use RS-232 for legacy instrument control. The MAX232BEAWE+ provides two drivers and two receivers in a 16-pin SOIC, allowing a controller to exchange commands and receive measurements without a separate level-conversion board. Because the interface is presented to firmware as ordinary UART logic, existing command protocols can remain unchanged. Designers should follow the manufacturer capacitor and layout recommendations, keep driver outputs isolated from receiver inputs, and confirm the instrument's RS-232 polarity. This arrangement is especially useful when a product has several internal rails but only one service port.
推荐
Data-Acquisition System
A data-acquisition controller can use the MAX232BEAWE+ to connect a UART processor or embedded control section to a remote RS-232 sensor, analyzer, or fixture. The 2/2 channel arrangement supports a bidirectional command link and can carry additional request or status signaling. Its 16-pin SOIC package limits PCB area while integrating the driver, receiver, and voltage-generation circuitry. A practical design should reserve a continuous common ground, apply the datasheet's charge-pump capacitor values, and place protection components where the cable enters the enclosure. Firmware should treat the interface as a UART peripheral and use framing or parity appropriate to the connected equipment.
推荐
Legacy Printer and Scanner Interface
The MAX232BEAWE+ is useful in embedded systems that must communicate with a legacy RS-232 printer, scanner, or terminal. Two transmitters and two receivers provide enough channels for bidirectional data and handshake signals without occupying a large portion of the board. The device converts ordinary UART signals to RS-232 levels, so the host processor does not need to generate bipolar cable voltages directly. Keep the cable-side traces away from sensitive analog circuitry, use the package ground as the circuit reference, and follow the connector's signal assignments. For new multi-port products, a higher-channel interface may reduce the number of required transceiver packages.
推荐
Configuration Port for Embedded Equipment
Embedded controllers can use the MAX232BEAWE+ for a manufacturing, field-service, or configuration port that accepts commands from a laptop or service terminal. The two-driver, two-receiver arrangement handles both command transmission and response signaling in a 16-pin SOIC. This allows a modern product to retain a simple maintenance path without exposing the UART pins directly to a cable. Design the port so the configuration interface can be disabled or physically isolated when not required. Check connector overvoltage protection, ground continuity, and the logic levels used by the attached host. The MAX232 datasheet remains the controlling reference for capacitor selection and signal routing.
推荐
Security and Access-Control Equipment
Access-control panels, credential readers, and security peripherals may use RS-232 for diagnostic or configuration communication. The MAX232BEAWE+ provides a compact two-channel interface with two RS-232 drivers and two receivers in a 16-pin SOIC. It can connect a supervisory controller to a legacy reader while preserving a standard UART-based firmware interface. Cable-side protection remains important because an external RS-232 port may be exposed to ESD and ground-potential differences. Place protection and the transceiver close to the connector, use a controlled ground reference, and keep the connector interface separate from security-critical power paths. Verify temperature and lifecycle requirements for the intended installation environment.
推荐
推荐产品汇总
工程参考数据: MAX232BEAWE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232ESE+T | MAX232BAWE+ | MAX232AEWE+ | MAX232ACWE+ | MAX232EWE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Transceiver Configuration | 2/2 | 2/2 | 2/2 | 2/2 | 2/2 | 2/2 |
| Driver Count | 2 drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers |
| Receiver Count | 2 receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
关键差异点
- Compact two-channel RS-232 integration (对比 MAX3243ECDWR)
- Exact same-family footprint alternative (对比 MAX232ESE+T)
- Direct UART-to-RS-232 interface (对比 MAX202EEWE-T)
设计说明
Place the charge-pump capacitor and its associated traces immediately beside the MAX232BEAWE+ pins, following the exact capacitor value and polarity or connection shown in the Analog Devices MAX232 datasheet. Keep these high-current charge-pump paths short and away from UART receiver traces. The 16-pin SOIC footprint simplifies assembly, but correct capacitor placement remains important for stable driver voltage generation and low output distortion.
Separate the cable-side RS-232 nets from low-level analog and clock signals. Route driver outputs directly toward the connector and avoid placing them beneath sensitive inputs or shared reference planes. Connect the transceiver ground to the interface ground near the IC, and evaluate the need for a dedicated connector-side protection network. This arrangement reduces capacitive coupling and helps prevent driver transitions from disturbing adjacent circuitry.
Do not substitute a MAX232 part solely because it has the same family name or a 16-pin package. Confirm the 2/2 channel configuration, supply arrangement, operating-temperature grade, pin names, and lifecycle status against the manufacturer datasheet. The 2/2 designation means two drivers and two receivers, so applications requiring four full RS-232 channels need a higher-channel transceiver. Also check connector DTE or DCE polarity before PCB release.
合规信息
The + ordering suffix indicates a lead-free packaging configuration, but formal RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status require confirmation from the manufacturer product page or declaration.