MAX232CEASE+ - 5V 2/2 RS-232 Transceiver | Analog Devices
料号: MAX232CEASE+ ✓ 量产中MAX232CEASE+ 概述
An RS-232 transceiver is an interface IC positioned between digital logic and a serial communications connector. Within the product hierarchy, it belongs to the RS-232 interface transceiver family and the broader category of interface ICs. Its two-driver, two-receiver arrangement supports one bidirectional RS-232 channel or two unidirectional channels, depending on how the pins are connected. Unlike a UART, which generates and interprets serial data but does not provide RS-232 voltage levels, the MAX232CEASE+ performs the physical-layer conversion between CMOS/TTL logic and RS-232.
The principal features are a +5 V supply, two transmit drivers, two receive receivers, full RS-232 operation, and a 16-pin SOIC footprint. The integrated charge-pump circuitry supports the positive and negative signal swings required at the driver outputs while the receiver inputs handle the bipolar RS-232 signal range. This makes the device useful where a modern microcontroller or application-specific controller has a UART but lacks a physical RS-232 level-shifting interface.
The MAX232 family is specified for EIA/TIA-232E and V.28/V.24 communications interfaces, including designs where ±12 V is unavailable. The single-supply architecture simplifies implementation compared with a discrete bipolar level-shifter circuit. Its 2/2 channel organization also provides flexibility for two independent transmit-only or receive-only links when all four interface pins are not needed in a single bidirectional port.
Typical applications include industrial serial adapters, test and measurement equipment, computer peripherals, security systems, and embedded-control subsystems. In each case, the transceiver provides the electrical interface between a low-voltage UART and an RS-232 port while keeping the host-side logic supply at +5 V.
PCB implementation should prioritize short driver traces, controlled return paths, and proper connection of the charge-pump capacitors specified by the manufacturer. External protection may be required when the RS-232 cable is exposed to electrostatic discharge or when the connected equipment uses longer cables.
This page combines the manufacturer interface description, package information, verified replacement candidates, comparison guidance, and practical PCB design notes. These engineering details help evaluators determine pin compatibility, electrical suitability, and implementation trade-offs before committing the MAX232CEASE+ to an RS-232 design.
直接替换替代料: MAX232CEASE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232CEASE+ (相同外形与封装尺寸) ——差异在于 Interface Standard, Package, Product Type, ESD Protection, Supply Voltage.
MAX232CASE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ACSE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ECSE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232EESE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ACWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232ECSE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232CEASE+ 规格参数
| Product Type | RS-232 transceiver |
| 电源电压 | +5 V |
| Transmitter Configuration | 2/2 |
| Driver Count | 2 |
| Receiver Count | 2 |
| Interface Standard | EIA/TIA-232E and V.28/V.24 |
| 封装 | 16-SOIC |
| 引脚数量 | 16 pins |
| 安装类型 | Surface mount |
MAX232CEASE+ 16-soic 引脚配置指南
MAX232CEASE+(16-soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232CEASE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232CEASE+ 适用于 6 应用s: Industrial RS-232 Adapter, Computer Peripheral Interface, Test and Measurement Equipment, Security and Access Control, Embedded Serial Communication, Data Acquisition and Control.
Industrial RS-232 Adapter
The MAX232CEASE+ fits an industrial serial adapter that exposes a 5 V UART controller through a conventional RS-232 connector. Its two drivers and two receivers support one bidirectional port while leaving a second driver-receiver pair available for an additional unidirectional link. The single +5 V supply simplifies system power design, while the integrated charge-pump function eliminates a separate bipolar RS-232 level-shifter. Place the IC near the connector, keep capacitor loops compact, and add cable-side transient protection when the adapter connects to field equipment.
推荐
Computer Peripheral Interface
The MAX232CEASE+ provides the physical RS-232 interface between a legacy peripheral port and a 5 V embedded controller. Its 2/2 channel arrangement allows a full-duplex console link or separate command and status paths, depending on connector assignment. Because the transceiver operates from +5 V and provides the required bipolar line levels internally, the controller can use a UART without external RS-232 transistors. Validate signal polarity, connector numbering, and grounding against the peripheral specification before fabrication.
推荐
Test and Measurement Equipment
The MAX232CEASE+ is appropriate for test and measurement equipment that retains an RS-232 control or service port. The two transmitters and two receivers can support one bidirectional command interface and a second status channel, improving instrument utilization without adding another transceiver package. Operating the entire interface from +5 V simplifies instrument power architecture, and the EIA/TIA-232E-oriented family targets legacy automation equipment. Keep the transceiver away from precision analog sections and use controlled grounding to prevent ground-current noise from affecting measurements.
推荐
Security and Access Control
The MAX232CEASE+ can bridge a 5 V access-control controller to an RS-232 reader, lock controller, or alarm interface. Two drivers and two receivers permit a bidirectional service channel and a dedicated one-way status indication when the system needs both. The single 5 V rail is convenient for embedded security equipment, while the transceiver handles RS-232 line conversion at the board edge. For door panels and long cable runs, add coordinated surge and electrostatic-discharge protection and verify the grounding strategy with the connected system.
推荐
Embedded Serial Communication
The MAX232CEASE+ is useful in embedded-control boards that retain a service or configuration port implemented through RS-232. A microcontroller can communicate through its UART while the transceiver converts logic levels to and from the bipolar interface. The two transmitter and two receiver channels provide enough connectivity for one full-duplex port plus an auxiliary direction, or for two differently assigned channels. Ensure the firmware uses the correct polarity and baud rate, and keep the RS-232 traces physically separated from high-current switching nodes.
推荐
Data Acquisition and Control
The MAX232CEASE+ can provide a legacy control connection in a data-acquisition system whose modern controller uses a UART. The +5 V transceiver simplifies the interface between embedded control electronics and RS-232-compatible instruments, while the two transmitter and two receiver channels support command and data paths. Place the transceiver at the connector side of the PCB and route it away from sensitive sensor inputs. Confirm the instrument's request-to-send, ready-to-send, and logic-polarity conventions before implementing the handshake.
推荐
推荐产品汇总
工程参考数据: MAX232CEASE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232CASE+ | MAX232ACSE+ | MAX232ECSE+ | MAX232EESE+ | MAX232ACWE+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Driver and Receiver Count | 2/2 | 2/2 | 2/2 | 2/2 | 2/2 | 2/2 |
| Interface Standard | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 |
| Ordering Grade | E grade | C grade | A grade | C grade | E grade | A grade |
关键差异点
- Two transmitters and two receivers in one 16-SOIC package (对比 MAX202EEWE-T)
- Single +5 V implementation (对比 MAX232CASE+)
- Supports bidirectional and split unidirectional RS-232 links (对比 MAX202EEWE-T)
设计说明
Place the MAX232CEASE+ close to the RS-232 connector and connect the charge-pump capacitors using short traces with a compact ground return. The manufacturer application circuit should be used as the layout reference because long capacitor loops can increase supply and radiated noise. Keep the transceiver and protected cable-side nodes away from precision analog inputs, switching regulators, and high-speed clock traces.
Do not treat the MAX232CEASE+ as a complete surge-protection solution. The transceiver converts logic levels to RS-232 but does not eliminate the need for suitable protection on exposed cable connections. Select protection with voltage, capacitance, and clamping characteristics compatible with the required data rate, and connect its return path to the correct signal or chassis-ground arrangement.
Confirm the package width and land pattern before substituting an ordering-code variant in the MAX232 family. The suffix controls ordering attributes such as temperature grade and SOIC width, so a shared 16-pin designation does not by itself guarantee identical PCB compatibility. Compare the manufacturer package drawing, minimum copper spacing, exposed connections, and assembly requirements before releasing a substitute to production.
合规信息
Compliance attributes require confirmation for the exact MAX232CEASE+ ordering code. The manufacturer product page identifies the MAX232 family as production; it does not by itself establish the target part's individual compliance status.