ADC/DAC
بەرهەمەکان (3,600+)
ADS7834P - 12-Bit 500 kSPS SAR ADC with 2.5V Reference | Texas Instruments
The Texas Instruments ADS7834P is a 12-bit, 500 kSPS single-channel successive-approximation (SAR) analog-to-digital converter with an internal 2.5 V reference and a synchronous serial interface, packaged in an 8-pin PDIP (through-hole DIP) package. It converts an unipolar analog input from 0 V to the reference voltage into a 12-bit digital word at up to 500,000 conversions per second, with typical power dissipation of only 11 mW at full throughput and 2.5 mW in power-down mode. A SAR ADC is a class of analog-to-digital converter that compares the unknown input voltage against an internal DAC and a comparator, bit by bit, on each clock cycle. Unlike a sigma-delta or pipeline converter, a SAR converter needs no continuous internal oscillator and no oversampling, which makes its behaviour deterministic and its digital output easy to filter in the time domain. In the hierarchy of signal-chain devices, the ADS7834P sits under ADC, then data converter, then signal-chain IC, then semiconductor. Key features of the ADS7834P include 12-bit resolution with a 500 kSPS sampling rate, a fully differential-free unipolar 0 V to VREF input range, an on-chip 2.5 V reference that can be bypassed or used to drive external circuitry, a low-power shutdown mode, and a simple synchronous serial (SPI-compatible) data interface with a chip-select line that holds the output in a high-impedance state. The internal reference eliminates the need for an external reference IC in most designs, reducing board area and cost. The device uses a charge-redistribution DAC array and a comparator-based SAR control loop, so each conversion is a fixed sequence of clock cycles and the acquisition time is deterministic. Because the reference voltage defines the full-scale range, accuracy is directly tied to the reference quality: the 2.5 V internal reference tolerance and temperature drift set the absolute accuracy of every converted code. Because the analog front end is a switched-capacitor network, the source impedance at the AIN pin must be kept low enough for the sampling capacitor to settle within the acquisition window. Typical applications include industrial process monitoring, thermocouple and RTD signal conditioning front ends, battery and power-supply telemetry, portable instrumentation, and low-cost data acquisition systems where a serial interface and through-hole package simplify assembly and prototyping. When designing around the ADS7834P, keep the analog trace from the sensor to the AIN pin short and shield it from digital switching lines, place the reference bypass capacitor close to the REFOUT pin, and treat the analog and digital return currents as separate paths that join only at the device ground pin. If higher resolution is required, more channels are needed, or the design cannot accept a serial interface, a different converter family will be a better fit than this part. This page combines manufacturer specifications, drop-in replacement options, parameter-by-parameter comparisons, and practical PCB and signal-integrity guidance that engineers can apply directly when qualifying the ADS7834P for a new design.
ADS7834PB - 12-Bit 500 kHz ADC | Texas Instruments
The Texas Instruments ADS7834PB is a 12-bit, 500 kHz sampling analog-to-digital converter with a 2.5 V input range, supplied in an 8-pin PDIP package for through-hole industrial and instrumentation designs. The converter supports single-channel analog input and is intended for data-acquisition systems that require moderate resolution, rapid sampling, and low-power operation. An ADC, or analog-to-digital converter, is a semiconductor that transforms a continuously varying analog voltage into a numeric value for processing by a microcontroller, DSP, PLC, or measurement instrument. The ADS7834PB belongs to the data-converter IC hierarchy and the ADC family, combining a 12-bit resolution, 500 kHz sampling capability, and serialized digital output in a compact eight-pin package. Its 12-bit conversion resolution produces 4096 discrete codes across the 2.5 V input range, corresponding to approximately 0.61 mV per code when referenced directly to that range. The 500 kHz sampling rate supports acquisition of rapidly changing signals, while the serial interface reduces the number of data pins required in systems with limited connector and PCB space. A stated full-scale error of 0.0244% supports precision-oriented measurement designs. The ADS7834PB operates from a 5 V supply and is specified over the -40 °C to +85 °C industrial temperature range. Its 8-pin PDIP package supports conventional through-hole assembly and is practical for prototypes, laboratory instruments, industrial controllers, and data-acquisition boards where a surface-mount footprint would not simplify assembly. Typical uses include sensor signal capture, process-control monitoring, laboratory measurement, industrial data logging, and embedded instrumentation. When designing around this converter, account for the acquisition system’s source impedance, reference accuracy, analog input filtering, digital-interface timing, and grounding. The 500 kHz conversion capability should also be distinguished from the complete system sample rate, which can be limited by digital communication and post-processing. This page combines manufacturer specifications, practical application guidance, package considerations, and a structured comparison with same-brand candidate converters. Use the Texas Instruments ADS7834 product page and device datasheet for the authoritative pin description, timing definitions, reference requirements, and application circuit before final PCB implementation.
ADS7835E - 12-Bit, 500 kSPS Low-Power SAR ADC | Texas Instruments
The Texas Instruments ADS7835E is a 12-bit, high-speed, low-power sampling analog-to-digital converter with a 500 kSPS throughput rate, a 2.5 V internal reference, and a serial interface, packaged in an 8-pin VSSOP (DBV) package. It is a single-channel, single-ended, successive-approximation (SAR) converter designed for cost-sensitive, space-constrained signal-chain designs. An SAR ADC is a sampling ADC type that converts an analog input to a digital code by successive comparison against an internal DAC, one bit per clock cycle. As a sampling ADC, it applies a sample-and-hold stage to the analog input before conversion. In the broader hierarchy the ADS7835E is a data converter -> ADC -> sampling ADC -> SAR ADC -> semiconductor, and it sits alongside voltage references, interface ICs and power management ICs in a typical industrial or instrumentation signal chain. Key features of the ADS7835E include a 500 kSPS throughput rate, on-chip 2.5 V reference, low power dissipation of 17.5 mW, single +5 V supply operation, and a serial interface that simplifies connection to microcontrollers and DSPs. The converter is guaranteed no-missing-codes, which simplifies gain calibration and guarantees monotonic transfer behaviour for closed-loop control and instrumentation use. The -40 °C to +85 °C temperature range covers industrial and commercial environments. Architecturally the device pairs a SAR conversion core with an internal sample-and-hold amplifier, a charge-based DAC array, and a reference buffer. Because the reference is internal, no external reference component or reference bypass network is required, which reduces board area. The digital interface exposes chip select (CS), serial clock (SCLK), serial data, and a sync/frame signal, allowing the converter to be daisy-chained with other serial peripherals on a shared bus. Typical applications include industrial process-control and sensor readout, portable battery-powered measurement instruments, low-cost data acquisition modules, and embedded control systems that need faster conversion than a low-speed sigma-delta ADC while keeping power low. The 500 kSPS rate suits vibration and monitoring loops sampled at audio or ultrasonic bandwidths. A key design consideration is decoupling: place a supply bypass capacitor close to the AVDD pin and route the analog and digital ground pins to a clean ground plane. Because the reference is internal, calibrate for gain accuracy at system level rather than adding a precision external reference. This page combines manufacturer specifications, ordering-code and drop-in alternatives, package details and practical design notes so engineers can qualify the ADS7835E quickly, compare it against equivalent converters, and place a procurement request from the same page.
ADS7835EB/2K5G4 - 12-Bit 500kHz Low-Power SAR ADC | Texas Instruments
The Texas Instruments ADS7835EB/2K5G4 is a 12-bit, high-speed, low-power successive-approximation (SAR) analog-to-digital converter with a 500 kHz throughput rate, internal 2.5 V reference, and synchronous serial interface, housed in an 8-pin MSOP (VSSOP) package supplied on a 2,500-piece tape-and-reel. The part accepts a single +5 V supply, draws only 17.5 mW in normal operation, and drops to 2.5 mW in power-down mode, making it one of the lowest-power 12-bit SAR ADCs in its class for battery-powered and portable designs. The analog input spans -VREF to +VREF (bipolar ±2.5 V around the internal reference), the converter guarantees no-missing-code 12-bit performance, and the digital interface is an SPI/QSPI/MICROWIRE-compatible serial port that supports low-cost galvanic isolation for remote data acquisition. A SAR ADC is a successive-approximation-register analog-to-digital converter - a type of data converter that uses a binary-search algorithm and an internal DAC to digitize an analog input one bit at a time per clock cycle, achieving deterministic latency and excellent DC accuracy without the latency or pipeline delay of pipeline ADCs. The ADS7835 family sits in the hierarchy: SAR ADC -> data converter (ADC) -> signal chain IC -> semiconductor. The internal 2.5 V bandgap reference eliminates an external reference component, and the synchronous serial interface minimizes pin count while supporting high-speed readback to an MCU or DSP. The key differentiating features of the ADS7835EB/2K5G4 versus competing 12-bit 500 kHz SAR ADCs are its 17.5 mW active / 2.5 mW shutdown power budget, an integrated 2.5 V reference (saving a discrete reference IC and ~$0.30 BOM cost), 8-pin MSOP packaging, and TI's long-term manufacturing support for the Burr-Brown™-heritage data-converter line. The "EB" suffix indicates the 8-pin MSOP (VSSOP) package with exposed pad, while the trailing "/2K5G4" indicates 2,500-unit tape-and-reel packaging with a Pb-free / RoHS-compliant finish. The synchronous serial data format and 500 kHz sample rate make the ADS7835EB/2K5G4 well suited to multi-channel data-acquisition systems, optical-module monitoring, and portable instrumentation that require a single +5 V rail, small PCB footprint, and predictable latency. Typical applications include portable multi-channel data loggers, wireless handset battery monitoring, optical-network power monitoring, and spectrum-analyzer IF digitizers where low power and small size are mandatory. When designing with this ADC, place a 0.1 µF ceramic bypass capacitor within 2 mm of the +VD pin, keep analog and digital grounds joined at a single star point beneath the exposed pad, and observe a 100 ns minimum acquisition time by clocking SCLK at or below the 500 kHz / 12-bit envelope. Add a 10 µF tantalum bulk capacitor on the analog supply if the source impedance exceeds 5 Ω to prevent reference droop during conversions.
ADS7835EQDGKREP - 12-Bit 500kHz Low-Power ADC | Texas Instruments
The Texas Instruments ADS7835EQDGKREP is a 12-bit, high-speed, low-power successive-approximation analog-to-digital converter (SAR ADC) that samples up to 500 kSPS with a single analog input channel, offered in an 8-pin MSOP/TSSOP (DGK) package and qualified to the Enhanced Product (EP) enhanced-reliability program for industrial and harsh-environment use. The part integrates a 2.5 V internal reference, consumes only 17.5 mW of power at full speed, and operates from a single +5 V analog supply. The "EP" suffix designates TI's enhanced-product screening flow, which adds extended temperature performance and controlled baseline for industrial customers. A SAR ADC is a successive-approximation-register analog-to-digital converter - a sub-category of data converters that uses a binary search algorithm and an internal precision DAC to digitize an analog input one bit at a time per clock cycle. SAR ADCs sit within the broader hierarchy of data converters (ADC/DAC) -> signal chain -> analog front-end -> mixed-signal IC. They are valued for zero-latency single-shot conversions, deterministic behavior, and excellent DC accuracy, making them preferred over delta-sigma ADCs when instantaneous sampling and fast response to input transients are required. Key features of the ADS7835EQDGKREP include a 500 kSPS maximum throughput rate, 17.5 mW typical power dissipation, a 2.5 V internal reference with low drift, a pseudo-differential analog input structure that accepts 0 V to VREF input signals, an SPI/QSPI/MICROWIRE-compatible serial data interface, and hardware-configurable unipolar input range. The internal reference eliminates the need for an external reference IC, reducing BOM count and PCB area. The serial interface minimizes I/O pin count, simplifying routing on dense mixed-signal boards. Architecturally, the converter uses a charge-redistribution DAC array controlled by a successive-approximation engine. The input is acquired on an internal sample-and-hold capacitor, then compared bit-by-bit against the reference. The 2.5 V reference is generated by a low-noise bandgap cell; its accuracy directly sets the converter's absolute gain error. The 8-pin MSOP/TSSOP package gives the part a footprint of roughly 3.00 mm x 3.00 mm, ideal for space-constrained applications. Typical applications include industrial process control loop monitoring, portable or battery-powered instrumentation, optical-module monitoring (laser bias current/voltage), high-speed closed-loop servo systems, and general-purpose data acquisition front-ends where 12-bit resolution and 500 kSPS throughput are sufficient. The single-channel architecture with serial output also makes the part a natural fit for multiplexed or multi-channel systems where an external MUX is acceptable. When designing with this device, ensure that the analog input does not exceed the supply rail minus the headroom required by the input ESD structures, and place the supply decoupling capacitor (typically 0.1 uF ceramic in parallel with 10 uF bulk) within a few millimeters of the AVDD pin. The serial clock (DCLK) should be kept low when CS is deasserted to prevent spurious conversions. This page consolidates distributor pricing, drop-in alternatives sourced from the TI ADS78xx family, and practical design notes that go beyond the manufacturer datasheet to accelerate schematic capture and BOM selection.
ADS7841E - 12-Bit 4-Channel 200 kHz ADC | Texas Instruments
The Texas Instruments ADS7841E is a 12-bit, 4-channel, single-ended sampling analog-to-digital converter with a 200 kHz conversion rate and synchronous serial interface, housed in a 16-pin SSOP package. Its resolution is programmable to 8 bits or 12 bits, while its reference voltage can vary from 100 mV to VCC to define the corresponding input range. A sampling ADC is a data-converter category that acquires an analog voltage at discrete intervals and converts it into a digital code. The ADS7841E belongs to the serial-output ADC hierarchy, combining a sample-and-hold input stage with a successive-approximation register and serial interface. This architecture is suited to control systems and embedded products where external host processors read converted samples over a compact serial bus. Four single-ended analog inputs can be selected through the serial interface. Alternatively, the inputs can be configured as two differential channels, allowing a small differential sensor signal to be measured relative to a common reference. The 12-bit resolution provides 4096 code levels, and the manufacturer datasheet states no missing codes with maximum integral nonlinearity and differential nonlinearity of ±1 LSB. The specified SINAD is 72 dB. The ADS7841E operates from a single supply, supports a reference voltage between 100 mV and VCC, and uses a synchronous serial interface for conversion commands and data transfer. Its typical power dissipation is 2 mW at a 200 kHz throughput rate with a +5 V supply. This combination of throughput, interface simplicity, and low typical power is useful when the system must acquire multiple analog measurements without using a high-power parallel ADC. Typical uses include resistive touchscreen controllers, industrial panel interfaces, battery-powered instruments, temperature-sensor acquisition, potentiometer measurements, and embedded analog control loops. A microcontroller can issue channel-selection and conversion commands, then receive the resulting 12-bit code through the serial data line. The ADS7841 is also applicable where two differential inputs provide better rejection of common-mode disturbance than single-ended measurements. Designers should provide suitable input and reference bypassing, use an external reference whose voltage remains within the specified range, and account for the serial interface timing. Because the converter supports both 8-bit and 12-bit operation, firmware and data scaling must match the programmed resolution. Supply and reference noise directly affect conversion accuracy, so layout should minimize traces between the reference source and the device. This product page consolidates the verified manufacturer and distributor information, practical application guidance, package details, and same-footprint alternatives. It also distinguishes documented electrical performance from parameters that require additional design data, helping engineers compare the ADS7841E with other members of the ADS7841 family before committing a PCB footprint.
ADS7841E/2K5G4 - 12-Bit 4-Ch 200kHz SAR ADC | Texas Instruments
The Texas Instruments ADS7841E/2K5G4 is a 12-bit, 4-channel serial-output sampling analog-to-digital converter (ADC) with a successive-approximation register (SAR) architecture, delivered in a 16-pin SSOP (QSOP) package on a 2,500-piece tape-and-reel format. The /2K5G4 suffix designates the G4 lead-free, RoHS-compliant version with tape-and-reel packaging, while the core ADS7841 silicon delivers up to 200 kHz throughput and ±1 LSB max INL/DNL with no missing codes. A successive-approximation register ADC (SAR ADC) is a type of analog-to-digital converter that uses a binary-search algorithm against an internal precision DAC to resolve an analog input to N bits in N clock cycles. SAR ADCs sit in the broader hierarchy of ADC architectures, which also includes delta-sigma, pipeline, flash, and dual-slope converters. Compared to pipeline ADCs they offer lower latency and no pipeline delay, and compared to delta-sigma parts they deliver much higher sampling rates at moderate resolution - making the 12-bit 200 kHz SAR a sweet spot for multiplexed data acquisition, instrumentation, and pen/digitizer front-ends. Key features of the ADS7841E include 4 single-ended or 2 differential input channels, a single +2.7V to +5.25V supply rail, 72 dB SINAD, a synchronous SPI/SSI-compatible serial interface with 8-bit or 12-bit programmable resolution, and typical power dissipation of just 2 mW at 200 kHz throughput on a +5V supply. The reference voltage VREF can be varied between 100 mV and VCC, allowing direct scaling to sensor output spans. An auto-power-down mode reduces consumption between conversions, and the SSOP-16 footprint is pin-compatible with the legacy ADS7841ES and ADS7843 family. The device is specified over the -40°C to +85°C industrial temperature range. Communication is via a 4-wire serial interface (CS, DCLK, DIN, DOUT) plus BUSY, supporting daisy-chaining of multiple ADS7841s on the same bus. A SHDN pin and PD0/PD1 bits implement low-power standby modes between conversions. Internal architecture uses a charge-redistribution DAC with a switched-capacitor comparator, yielding excellent DC linearity and very low aperture uncertainty suitable for touch-screen digitizer applications. Typical applications include 4-wire resistive touch-screen controllers, pen-digitizer digitizing tablets, industrial process-control data acquisition modules, portable battery-powered instrumentation, and general-purpose multiplexed analog input modules for embedded systems. The wide VREF range also makes it suitable for thermocouple and bridge-sensor front-ends. The part is also marketed as an alternate source for the legacy ADS7841ES, easing second-source qualification for existing designs. When designing with the ADS7841E/2K5G4, ensure the VREF decoupling capacitor is placed within 5 mm of the REF pin to avoid conversion errors, and route the BUSY signal away from the analog inputs to prevent digital crosstalk into the sampled value. Note that the ADS7841E/2K5G4 is now marked obsolete by Texas Instruments with no direct replacement; designers should evaluate the active parametric equivalent ADS7841E/2K5 or migrate to the ADS7843/ADS7844 family for new designs. This page synthesizes distributor pricing, drop-in equivalents, and practical design notes that go beyond what is in the manufacturer datasheet, giving engineers a single reference for legacy, current-production, and cross-brand options in the same SSOP-16 footprint.
ADS7841EB - 12-Bit 4-Channel 200ksps ADC | Texas Instruments
The Texas Instruments ADS7841EB is a 12-bit, 4-channel, successive-approximation analog-to-digital converter with a synchronous serial interface and a 200 ksample/s conversion rate. It is offered in a 16-pin SSOP package and accepts four single-ended inputs or two differential inputs. Its resolution can be programmed for either 8-bit or 12-bit operation, while the reference input can range from 100 mV to VCC, establishing a corresponding 0 V to VREF input range. An ADC converts continuous analog voltages into digital values for measurement, control, and data-acquisition systems. The ADS7841 belongs to the sampling ADC hierarchy, combining an internal sample-and-hold stage with a successive-approximation converter and a synchronous serial interface. This positioning makes it suitable for compact embedded systems that require multiple analog inputs without the complexity of a high-speed parallel ADC. The principal features include 12-bit nominal resolution, four selectable analog channels, and a maximum throughput of 200 ksample/s. The converter provides ±1 LSB maximum integral and differential nonlinearity, no missing codes, and 72 dB SINAD according to the manufacturer datasheet. It also supports single-supply operation and programmable 8-bit or 12-bit conversion resolution, allowing a faster communication mode when full-resolution output is not required. The ADS7841 uses a synchronous serial interface, identified in product listings as SPI-compatible, for receiving conversion commands and transferring converted data. This interface reduces the number of signal paths required between the ADC and a microcontroller. Although the sampling architecture provides useful conversion throughput, output-word latency and the selected serial clock must be considered when establishing the overall sampling rate in a complete acquisition system. Typical uses include resistive touch-screen sensing, industrial control panels, potentiometer and sensor measurement, battery monitoring, and compact data-acquisition modules. The four single-ended inputs are useful when several analog quantities must be scanned sequentially, while differential-input operation helps reject common-mode noise in suitable sensor interfaces. The low 2 mW typical power dissipation at a 200 kHz throughput rate and 5 V supply supports space-constrained and portable equipment. Design attention should focus on reference stability, input-source settling, serial timing, and PCB grounding. Place input and reference capacitors close to their associated pins, maintain a quiet return path, and allow sufficient acquisition time for the source and sample-and-hold network to settle. The manufacturer pin-description table should be used directly when assigning PCB tracks and checking the exposed package constraints. This product page combines the manufacturer electrical characteristics, package details, commercial guidance, comparison criteria, and practical PCB considerations to support faster component selection. It also distinguishes true same-footprint alternatives from devices that differ in resolution, channel count, conversion rate, or package and therefore may require redesign.
ADS7841ES/2K5 - 12-Bit 4-Ch 200kHz SAR ADC | Texas Instruments
The Texas Instruments ADS7841ES/2K5 is a 12-bit, 4-channel serial-output sampling analog-to-digital converter (ADC) housed in a 16-pin SSOP package. It supports up to 200 kHz conversion rate through a successive-approximation register (SAR) architecture, with single-ended or differential input configurations selectable per channel, ±1 LSB maximum INL/DNL, no missing codes, and 72 dB SINAD. A SAR ADC is a successive-approximation-register analog-to-digital converter that uses a binary-search algorithm combined with an internal DAC to digitize an input sample in N clock cycles, where N is the resolution in bits. SAR ADCs sit within the broader analog-to-digital converter family (SAR > ADC > data converter > signal chain IC > semiconductor) and are favored over sigma-delta and pipeline architectures when low latency, single-shot conversions, and moderate-to-high sampling rates (tens of kHz to a few MHz) are required in multiplexed-channel applications. Key specifications include 12-bit resolution (programmable to 8 or 12 bits via the MODE pin/bit), 4 single-ended or 2 differential input channels, 3.75 µs typical conversion time, 0.0488 % linearity error, single +2.7 V to +5 V supply operation, and a synchronous serial (SPI-compatible) interface. Typical power dissipation is 2 mW at 200 kHz throughput with a +5 V supply, and the reference voltage VREF can vary between 100 mV and VCC for input scaling flexibility. The ADS7841 implements a four-wire SPI/SSI-compatible synchronous serial interface with a BUSY output, making it straightforward to interface with microcontrollers, DSPs, and modern SoCs. The 16-bit SSOP (DBQ) package is a thin-shrink small-outline outline surface-mount form factor from the SSOP family, providing a compact 5.3 mm body width suitable for space-constrained data-acquisition boards. Typical applications include pen-touch digitizers, battery-monitoring systems, isolated data acquisition, industrial process control, and portable instrumentation. The /2K5 suffix indicates tape-and-reel packaging with 2500-unit reels, oriented toward production-volume assembly. When designing with this part, place the 0.1 µF VCC bypass capacitor as close as possible to the supply pin and route the BUSY and DOUT lines away from noisy switching nodes to preserve the 72 dB SINAD figure at full speed. The MODE pin defaults to 12-bit mode when held LOW, allowing software override when held HIGH. This page consolidates distributor pricing, pin-compatible drop-in alternatives, and practical PCB design notes not found in the standalone manufacturer datasheet, with the goal of accelerating the engineer selection and review process.
ADS7841P - 12-Bit 4-Channel SAR ADC | Texas Instruments
The Texas Instruments ADS7841P is a 12-bit, 4-channel, single-SAR analog-to-digital converter with a synchronous serial interface, a 200 kHz throughput rate, and a 16-pin PDIP package. Its reference voltage can vary from 100 mV to VCC, allowing the input range to scale from 0 V to VREF while the converter operates from a 2.7 V to 5.25 V supply. A sampling analog-to-digital converter samples an analog voltage and converts it into a digital code. The ADS7841 belongs to the SAR ADC category within the broader ADC hierarchy, combining an internal sample-and-hold function, a 12-bit successive-approximation conversion stage, and a serial interface. This architecture is suited to control panels, resistive touch screens, potentiometers, sensors, and other systems that require compact, multiplexed analog measurement. The ADS7841 can operate in 12-bit or programmable 8-bit resolution modes. According to the Texas Instruments ADS7841 datasheet, typical power dissipation is 2 mW at a 200 kHz throughput rate and a 5 V supply. Four analog input channels are selected through the serial interface, reducing the number of external analog multiplexing components required in a multi-sensor design. The flexible reference range also supports systems whose analog signal amplitude is smaller than the supply voltage. The device uses a synchronous serial interface for conversion control and result transfer. Control signals include chip select, serial clock, and serial data input, while converted data is returned through the serial data output. Synchronous operation allows the host processor or controller to establish a defined sampling and conversion sequence, which is important when measurements must repeat at predictable intervals. Typical applications include resistive touchscreen input, industrial control interfaces, portable measurement equipment, sensor conditioning, and embedded systems with several slowly changing analog inputs. The 16-pin PDIP package is appropriate for through-hole prototypes, legacy control boards, and systems where a large lead spacing simplifies manual assembly or connector routing. Designers should verify the analog and digital ground arrangement, route sensitive input traces away from switching nodes, and place input and reference capacitors close to their associated pins. The selected VREF voltage determines the analog input span, while the host firmware must handle channel selection, sampling timing, and the configured 8-bit or 12-bit result format. This product record combines the manufacturer specifications with package, application, sourcing, and design guidance. It also distinguishes verified drop-in alternatives from devices with different packages or interfaces, helping engineers make PCB-level replacement decisions without conflating electrical similarity with physical compatibility.
ADS7841PBG4 - 12-Bit 4-Ch 200kHz SAR ADC | Texas Instruments
The Texas Instruments ADS7841PBG4 is a 12-bit, 4-channel successive-approximation analog-to-digital converter (SAR ADC) with synchronous serial output, packaged in a 16-pin PDIP (through-hole) and rated for industrial -40C to +85C operation. It supports 4 single-ended or 2 differential inputs, delivers up to 200 kHz sampling, and offers pin-programmable 8-bit or 12-bit resolution. Key specifications include +/-1 LSB max INL and DNL, no missing codes, 72 dB SINAD, 2 mW typical power dissipation at 200 kHz throughput, and a 3.75 us conversion time. A SAR ADC is a type of data converter that uses a binary-search successive-approximation algorithm to digitize an analog input in N clock cycles for N bits of resolution. SAR ADCs sit in the broader data-converter hierarchy of analog-to-digital converters, which also include delta-sigma, pipeline, and flash architectures. Within TI's portfolio, SAR ADCs are the workhorse choice for medium-speed (10 kSPS to 1 MSPS), medium-resolution (8 to 16 bit) multiplexed applications where low latency, deterministic throughput, and simple SPI/QSPI/MICROWIRE-compatible serial interfaces are required. Key features of the ADS7841 include single +2.7V to +5.5V supply operation, a software-controlled shutdown mode that drops supply current to under 1 uA, an analog input range of 0V to VREF, and a reference voltage (VREF) that can be varied from 100 mV to VCC. The four analog inputs are selected by a 2-bit address and a 1-bit single-ended/differential control word clocked into the DIN pin, making the part pin-compatible with industry-standard touch-screen controllers of the same era. The 16-PDIP package supports breadboard and through-hole prototyping as well as legacy industrial backplanes. Typical applications include industrial process control, portable data acquisition, isolated sensor front ends, pen/touch input replacement, and battery-powered instrumentation. The wide supply range and 1 uA shutdown current also make the part suitable for power-constrained remote-sensor nodes where the ADC is duty-cycled awake only when a measurement is needed. When designing with the ADS7841PBG4, decouple VCC with a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin, and bypass VREF with at least 1 uF of effective capacitance to keep the reference stable across conversions. The serial clock (DCLK) frequency is limited to 2.048 MHz at VCC = 5V (derate to 1.2 MHz at 2.7V) - the host MCU must respect this ceiling for reliable conversions. CS must be brought high after the 24th SCLK to complete the conversion cycle; floating CS mid-frame yields a corrupted sample. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet to help engineers select, source, and integrate the ADS7841PBG4 with confidence.
ADS7841PG4 - 12-Bit 4-Ch Serial ADC, 200kHz, 16-PDIP | Texas Instruments
The Texas Instruments ADS7841PG4 is a 12-bit, 4-channel, serial-output sampling analog-to-digital converter (ADC) housed in a 16-pin PDIP (N) package with through-hole mounting. The "G4" suffix designates the Pb-free (lead-free) finish variant of the ADS7841 family, and the part is specified over the -40C to +85C industrial temperature range. The converter integrates a successive-approximation register (SAR) architecture with an on-chip sample-and-hold, supports a synchronous serial (SPI/QSPI/MICROWIRE-compatible) interface, and is specified for a 200 kHz throughput rate with a single +5V analog supply and a logic supply down to +2.7V. What is a SAR ADC? A successive-approximation register analog-to-digital converter is a precision data-acquisition IC that uses an internal binary-search algorithm to convert an analog input to a digital code one bit per clock cycle. SAR ADCs are valued for deterministic latency, low power consumption, excellent DC accuracy, and no pipeline delay, making them the workhorse for multiplexed multi-channel data acquisition, industrial process control, and portable instrumentation. The ADS7841PG4 belongs to the data-acquisition ADC category and provides broader data acquisition density in the semiconductor hierarchy. Key features include 4 single-ended or 2 differential input channels, programmable resolution (8 bits or 12 bits), ±1 LSB maximum INL and DNL with no missing codes at 12 bits, 72 dB SINAD, and a low 2 mW typical power dissipation at 200 kHz throughput on a +5V supply. The reference voltage (VREF) is independent and can be varied from 100 mV up to VCC, giving an input voltage range of 0V to VREF. An auto power-down mode reduces dissipation between conversions. Typical applications include pen-touch screen digitizers (the part's original target market), industrial process-control analog front ends, portable battery-powered measurement instruments, multi-channel sensor signal conditioning, and digital multimeter (DMM) front ends. The wide input range and reference flexibility make it well-suited for low-voltage sensor bridges and 4-20 mA current-loop digitization after a shunt resistor. When designing with the ADS7841PG4, place 100 nF decoupling capacitors close to both VCC and VREF, keep analog and digital grounds joined only at one point, and route DCLK, DIN, DOUT, CS, and BUSY traces short and away from noisy digital lines. Use the auto power-down mode (PD1=PD0=0) to keep average current under 1 mA in battery-powered applications.
ADS7842E - 12-Bit 4-Channel 200 kHz SAR ADC | Texas Instruments
The Texas Instruments ADS7842E is a 12-bit, 4-channel, successive-approximation-register analog-to-digital converter with a 200 kHz sampling rate and a 28-pin SSOP package. Its single-supply operating range is 2.7 V to 5 V, and its parallel microprocessor interface uses three-state outputs for direct connection to digital buses. An ADC is a data-conversion device that transforms an analog voltage into a numeric value for processing, measurement, or control. The ADS7842E belongs to the SAR ADC family, where a capacitor-based internal DAC successively approximates the input voltage. Within the broader hierarchy, it is a data-converter IC, an interface IC, and a semiconductor designed for data-acquisition and embedded measurement systems. Key features include four analog inputs through a multiplexer, 12-bit resolution, a 200 kHz conversion rate, and ±1 LSB integral and differential nonlinearity. The converter also provides 72 dB signal-to-noise and distortion ratio and low power dissipation of 2 mW. These characteristics suit precision measurements where four analog signals must be digitized rapidly without employing a high-power switching converter. Internally, the ADS7842E combines a four-channel analog multiplexer, 12-bit capacitor-based SAR converter, sample-and-hold amplifier, microprocessor interface, and parallel three-state output drivers. The tri-state outputs allow the device to share digital bus connections with other peripherals, reducing contention when the processor does not select the converter. The reference voltage is adjustable, supporting analog ranges selected by the system designer. Typical applications include industrial data acquisition, test and measurement equipment, battery-powered instrumentation, and process-control systems. The four-channel input structure reduces the need for multiple converters when several slowly changing sensors must share one digital interface. The 200 kHz sampling capability also supports higher-rate sampled measurements when settling and signal-conditioning requirements are satisfied. The primary design consideration is analog signal conditioning. Inputs must remain within the converter's specified operating range, and the reference, supply, and bypass connections require careful layout. A quiet reference and short analog traces are especially important because gain, noise, and conversion accuracy depend on the complete analog signal chain rather than on resolution alone. This page combines manufacturer specifications, practical application guidance, interface considerations, and structured comparisons with compatible Texas Instruments ordering variants. These engineering details help distinguish the ADS7842E from related converter families and simplify footprint and procurement planning.
ADS7842E/1K - 12-Bit 4-Channel 200ksps ADC | Texas Instruments
Texas Instruments ADS7842E/1K is a 12-bit, 4-channel successive-approximation-register analog-to-digital converter with a 200 ksample/s conversion rate, parallel output interface, and 28-pin SSOP package. It operates from a single 2.7 V to 5 V supply and offers an adjustable 100 mV to VCC reference range. The integrated four-channel analog multiplexer, sample-and-hold amplifier, and three-state parallel outputs make the ADS7842 a complete converter for microprocessor-controlled measurement systems. An ADC converts an analog input voltage into a digital value suitable for processing, measurement, logging, or control. The ADS7842 belongs to the SAR ADC family, where an internal capacitor-based DAC and successive comparison determine each conversion result. Within the electronics hierarchy, it is a data-converter IC and an ADC/DAC category component designed for precision analog-signal capture. Its four-input multiplexer supports multiple sensors or measurement nodes without requiring four separate converter packages. Key features include 12-bit resolution, a maximum sampling rate of 200 ksample/s, ±1 LSB integral and differential nonlinearity, and 72 dB SINAD. The single-supply operating range of 2.7 V to 5 V supports both 3.3 V and 5 V systems. An adjustable reference from 100 mV to VCC changes the full-scale input range and corresponding LSB resolution from 24 µV to 1.22 mV. Low power dissipation of 2 mW helps reduce system energy consumption in portable and battery-operated instruments. The device combines a four-channel analog multiplexer, sample-and-hold amplifier, 12-bit SAR core, control logic, and three-state parallel output drivers. Parallel data output permits direct connection to appropriately buffered microprocessor or data-bus circuitry. The three-state outputs can place the bus in a high-impedance state when the converter is not selected. At 200 ksample/s, the architecture provides sufficient throughput for moderate-rate instrumentation while retaining the simple control and conversion behavior associated with SAR ADCs. Typical uses include portable data loggers, test and measurement equipment, industrial process monitoring, battery-powered instruments, and laboratory data-acquisition systems. It is particularly useful when several analog channels must be sampled with a compact parallel-interface converter. The 200 ksample/s rate supports rapidly changing sensor signals, while the 12-bit result provides 4096 digital codes across the selected reference range. PCB design should provide a low-impedance reference network and short analog traces to minimize acquisition errors and coupling. Decoupling capacitors should be placed close to the supply and reference pins, and digital output routing should avoid crossing sensitive input paths. Because the converter uses an adjustable reference, resistor and capacitor tolerances directly influence LSB size and calibration accuracy. This product page combines the manufacturer specifications with practical application guidance, package details, replacement considerations, interface constraints, and PCB design notes. These engineering details help designers determine whether the ADS7842E/1K’s 12-bit resolution, four-channel multiplexing, 200 ksample/s throughput, parallel bus, and 2.7 V to 5 V supply range fit a specific data-acquisition design.
ADS7842E/1KG4 - 12-Bit 4-Ch 200kHz SAR ADC | Texas Instruments
The Texas Instruments ADS7842E/1KG4 is a 12-bit, 4-channel, successive-approximation-register (SAR) analog-to-digital converter that samples at up to 200 kHz and delivers parallel 3-state outputs in a 28-pin SSOP (DB) tape-and-reel package. It integrates a capacitor-based SAR ADC, a sample-and-hold amplifier, a microprocessor-compatible interface, and three-state parallel output drivers. Maximum linearity error is 0.0488% (1 LSB), reference input range is 3 V or 5 V, and power consumption is approximately 2 mW at the rated throughput. The G4 suffix indicates Pb-free, RoHS-compliant assembly on tape and reel. A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary-search algorithm against an internal capacitive DAC to resolve one bit per clock cycle. SAR ADCs sit in the broader hierarchy of ADCs (successive approximation, sigma-delta, pipeline, flash), and within mixed-signal data acquisition ICs. SAR converters are favored where low latency, deterministic throughput, and moderate resolution (8-16 bit) matter, such as in multiplexed sensor front ends and process control loops. Key features include a 200 kHz maximum sample rate, 4 single-ended analog input channels with internal multiplexer, 12-bit no-missing-codes resolution, ±1 LSB max INL, ±1 LSB max DNL, and a parallel interface that drops directly onto 8-/16-bit microprocessor data buses. The device accepts a 2.7 V to 5.5 V analog supply and digital supply, supports an external reference, and includes a power-down mode that drops quiescent current to microamp levels for battery-powered designs. Architecturally, the ADS7842 uses a charge-redistribution DAC switched by the SAR logic clocked from the external oscillator applied to the CLK pin. The sample-and-hold front end captures the input on the rising edge of CS, and conversion completes within 16 clock cycles. Parallel 3-state drivers allow the data bus to be shared with other peripherals without external buffers. Typical applications include industrial process control (multi-loop PLC analog front ends), data acquisition systems, multi-channel instrumentation, medical patient monitoring front ends, and battery management analog input aggregation. The 4-channel input count makes the part cost-effective when 2-4 sensors must be read through one ADC. Designers should size the external reference decoupling carefully (typically 10 uF tantalum in parallel with 0.1 uF ceramic) and ensure the CLK pin is driven with a clean 50%-duty-cycle waveform between 0.1 MHz and 2.5 MHz. Avoid routing digital outputs directly beneath the analog input traces to minimize digital-to-analog coupling into the next conversion cycle.
ADS7842EB - 12-Bit 4-Channel ADC | Texas Instruments
The Texas Instruments ADS7842EB is a 12-bit, 4-channel, successive-approximation sampling analog-to-digital converter with a parallel output interface, a maximum sampling rate of 200 kSPS, and a 28-pin SSOP (DB) package. It operates from a single supply and is designed for compact data-acquisition systems that need to digitize several analog input channels through one converter. An ADC is a data-acquisition IC that converts an analog voltage into a numeric value for processing, measurement, or display. The ADS7842EB belongs to the successive-approximation ADC family and combines an internal 4-channel multiplexer with a 12-bit conversion engine. Its parallel interface transfers each converted code directly to a digital system, making it suitable for designs that favor deterministic sampling and straightforward bus connection over serial-interface simplicity. Key features include four analog inputs, 12-bit resolution, and a 200 kSPS sampling rate. The converter provides ±1 LSB integral and differential nonlinearity, no missing codes, and 72 dB SINAD. Its low power consumption is specified as 2 mW, while the single-supply architecture reduces the number of external rails required in acquisition equipment. The industrial-grade ADS7842EB is identified as a 28-pin SSOP device. Internally, the four-channel multiplexer routes one selected input to the successive-approximation conversion stage. The digital portion presents the 12-bit result through a parallel interface, allowing the host processor, microcontroller, or programmable logic to capture the conversion result. Because the input is multiplexed, the system must select each channel and allow the associated acquisition and conversion timing before interpreting the output code. Typical uses include industrial process monitoring, data-acquisition instruments, panel-meter interfaces, sensor signal conditioning systems, and embedded measurement equipment. The four-channel arrangement is especially useful when several sensors must share one converter while retaining a compact parallel-data architecture. System designers should also account for acquisition time, conversion time, channel-selection sequencing, reference accuracy, and the required settling time. The primary layout consideration is keeping analog inputs, voltage reference, and ground connections away from fast digital output traces. Place input and reference bypass capacitors close to their associated pins, use a quiet analog ground strategy, and route the 12-bit parallel bus in a consistent topology. Verify signal levels and timing against the host device before treating the ADS7842EB as a direct interface replacement. This product page combines the verified manufacturer and distributor descriptions with practical engineering guidance, package and interface comparisons, and drop-in-family alternatives. It is intended to support part selection, schematic review, PCB planning, and qualification of the ADS7842EB for multi-channel analog measurement designs.
ADS7843E - 12-Bit Resistive Touch Controller | Texas Instruments
Texas Instruments ADS7843E is a 12-bit sampling analog-to-digital converter with a synchronous serial interface and integrated low-on-resistance switches for driving a four-wire resistive touch screen. It supports conversions up to 125 kHz, operates from a single 2.7 V supply, and typically consumes 750 uW at a 125 kHz throughput rate with a 2.7 V supply. The device is offered in a 16-pin SSOP package. A resistive touchscreen controller is an ADC-and-switch combination that measures voltage ratios from a four-wire touch panel. The ADS7843E belongs to the analog-to-digital converter hierarchy, where the ADC digitizes the touch-panel voltage and the synchronous serial interface transfers conversion results to a host processor. Its ratiometric conversion method allows the reference voltage to vary from 1 V to VCC, producing a corresponding input range from 0 V to VREF. Key features include programmable or 12-bit resolution, two auxiliary analog inputs, a four-wire resistive touch-screen interface, and full power-down control. The 125 kHz conversion capability supports responsive touch sampling while the ratiometric measurement approach helps compensate for supply and reference variations. The 16-pin SSOP format also supports compact, surface-mount touchscreen modules. Internally, the controller combines switched inputs, a sampling ADC, a reference path, and a synchronous serial interface. The low-on-resistance switches reduce the load presented to the touch panel, while the auxiliary inputs let the host monitor additional analog signals through the same converter. Conversion results are transferred through the serial interface, allowing the ADS7843E to operate as a peripheral to a microcontroller or embedded controller. Typical applications include four-wire resistive touchscreen panels in industrial HMIs, portable instruments, test equipment, medical-device interfaces, and compact embedded control panels. The 12-bit resolution supports touch-position calculations across a typical X-Y panel, while the 125 kHz sampling rate can be adapted to the host interface and required response time. When connecting the touch panel, maintain the recommended analog layout and route the touch, reference, and serial signals to minimize interference. Select output data rate, reference voltage, and auxiliary-channel multiplexing in software according to the host sampling rate and control-panel responsiveness. This page combines the manufacturer specifications with practical interface guidance, sourcing paths, and a parameter comparison for engineers evaluating touch-screen controllers. It focuses on the ADS7843E itself rather than treating the different order codes as functionally distinct designs.
ADS7844E - 12-Bit 8-Channel 200 kHz ADC | Texas Instruments
The Texas Instruments ADS7844E is a 12-bit, 8-channel serial-output sampling analog-to-digital converter with a synchronous serial interface, 200 kHz conversion rate, and 20-lead SSOP package. It supports eight single-ended input channels or four differential input channels, while operating from a single supply. Typical power dissipation is 3 mW at a 200 kHz throughput rate with a +5 V supply. A sampling ADC is an analog-to-digital converter that acquires an input voltage through a sample-and-hold circuit and converts it into a digital code. The ADS7844E belongs to the ADC > data converter > integrated circuit hierarchy and is designed for compact embedded systems requiring multiple analog measurements, controlled serial output, and low power consumption. Its reference voltage can vary from 100 mV to VCC, with a corresponding input range of 0 V to VREF. The device provides 12-bit resolution, eight single-ended or four differential inputs, and conversion throughput up to 200 kHz. Its synchronous serial interface supports communication with a microcontroller or other digital controller, while shutdown mode reduces power dissipation when conversion activity is not required. The single-supply operation and selectable reference range make the converter useful in industrial control, instrumentation, data acquisition, and embedded analog monitoring systems. The ADS7844E uses a sampling architecture rather than a continuous-time delta-sigma or pipeline architecture. This supports relatively high throughput for a multiplexed converter while keeping the device suitable for low-power embedded designs. Input selection, reference handling, serial timing, and acquisition control are managed through the device interface and external circuitry. The application engineer must account for the settling time of the sample-and-hold network when multiplexing channels at high conversion rates. Typical applications include touch-panel and resistive input scanning, industrial sensor interfaces, programmable gain control systems, battery-powered instrumentation, and factory automation modules. The 8-channel input arrangement is useful when several analog quantities must be measured with one converter. The 3 mW typical dissipation figure makes the part attractive for embedded systems where overall power budget and board area are constrained. Designers should pay close attention to the reference voltage, analog input range, source impedance, acquisition timing, and serial-interface wiring. Input and reference bypassing, grounding, signal conditioning, and digital return-current management can materially affect conversion accuracy. The 20-lead SSOP package also requires adequate lead clearance and careful assembly planning during manual inspection or rework. This product summary combines manufacturer identification, distributor package information, ADS7844 feature descriptions, and cross-reference findings. It distinguishes verified ADS7844E characteristics from unavailable detailed electrical, pricing, and pin-assignment data so engineers can make a traceable initial selection and then confirm the complete operating limits in the official Texas Instruments datasheet.
ADS7844N - 12-Bit 8-Channel SAR ADC | Texas Instruments
The Texas Instruments ADS7844N is a 12-bit, 8-channel serial-output sampling analog-to-digital converter with a synchronous serial interface and a 200 kHz conversion rate. It supports eight single-ended input channels or four differential input channels, operates from a single supply, and is available in a 20-pin SSOP package. A sampling ADC, or successive-approximation-register ADC, converts an analog voltage into a digital code by sampling an input and comparing it with an internal reference through a sequence of approximations. The ADS7844N belongs to the broader ADC, data-converter, and semiconductor hierarchy, and is designed for applications requiring multiple analog measurements, programmable gain, and serial communication with a microcontroller or embedded control system. Key features include 12-bit resolution, eight selectable channels, single-ended or differential input operation, a 200 kHz conversion rate, and an adjustable reference input that can range from 100 mV to VCC. The input voltage range follows the selected reference voltage, allowing the converter to be scaled for sensors, potentiometers, and low-voltage analog signals. The device also includes shutdown functionality to reduce power dissipation when conversions are not required. The ADS7844N uses a synchronous serial interface with serial data output, clock input, chip select, and differential or single-ended input multiplexing. Its typical power dissipation is 3 mW when operating from a 5 V supply at a 200 kHz throughput rate. The reference voltage can be selected independently of the supply, which helps define the full-scale conversion range and improves flexibility when analog signals occupy only a portion of the converter input range. Typical applications include resistive touch-screen controllers, industrial panel interfaces, portable measurement equipment, battery-powered instruments, data acquisition modules, and embedded control systems. A microcontroller can issue a conversion command, select the analog channel, and receive the resulting 12-bit value over the serial interface. In a touch-panel design, the converter can measure the X and Y voltages while its multiplexer and differential-capable inputs support front-end signal conditioning. When laying out the ADS7844N, keep the analog input traces short, provide a stable reference bypass capacitor, and route serial clock and data traces away from sensitive analog inputs. The 20-pin SSOP package has no exposed pad, so thermal performance depends primarily on the PCB copper area, ambient temperature, and conversion workload. Confirm the complete pin-description table in the manufacturer datasheet before assigning PCB nets. This page combines the official TI product information, the manufacturer ADS7844 data sheet, and cross-reference results to support component identification, comparison, sourcing, and board-level design. It also provides application guidance, pin-package references, and an explicit distinction between confirmed drop-in alternatives and devices that require functional rather than footprint-level review.
ADS7845E - 12-Bit 5-Wire Touch Controller | Texas Instruments
Texas Instruments ADS7845E is a 12-bit resistive touch-screen controller with ratiometric conversion, a synchronous serial interface, and a 16-lead SSOP package. It operates from a single 2.7 V to 5 V supply, supports a conversion rate up to 125 kHz, and includes auxiliary analog inputs. These characteristics make it suitable for compact resistive touch panels used in portable instruments, industrial controls, and embedded human-interface systems. A 5-wire resistive touch-screen controller is an analog interface integrated circuit that measures X and Y coordinates by applying controlled voltages through the transparent resistive layers of a touch panel. The measured voltage represents position relative to the panel edges, so the controller converts the analog result into a digital value for a host processor. The ADS7845E occupies the touchscreen-controller branch of the ADC and interface hierarchy, combining a sampling ADC, low-on-resistance switches, reference control, and serial communication in one device. The controller provides 12-bit resolution, ratiometric conversion, and a maximum conversion rate of 125 kHz. Its low-power design supports portable equipment, while the power-down function helps reduce consumption when touch input is not required. A variable reference voltage from 1 V to VCC allows the analog conversion range to be matched to system requirements. The 16-lead SSOP package also provides a compact surface-mount format suitable for space-constrained control boards. In operation, the host processor controls the ADS7845E through its synchronous serial interface. The controller drives the resistive panel, samples the resulting analog voltage, and returns a 12-bit conversion result. Ratiometric operation references the measurement to the supply voltage, which can reduce sensitivity to supply variation when the host and touch interface share the same reference. The auxiliary analog inputs extend the device beyond touch-coordinate acquisition when additional analog measurements are required. Typical implementations include portable data-acquisition terminals, industrial operator panels, laboratory instruments, medical-device interfaces, and compact HMI systems. The 125 kHz conversion rate supports responsive coordinate acquisition, while the 2.7 V to 5 V supply range permits use with both 3.3 V and 5 V embedded systems. Designers should select the correct SSOP footprint and follow the manufacturer pin-description and recommended application-circuit tables when assigning signals. A key design consideration is preserving clean, low-impedance analog routing between the controller and the touch-panel connector. Keep the touch and auxiliary input traces short, place bypass capacitance close to the supply pins, and avoid switching-regulator nodes beneath the analog signal paths. The measured coordinate accuracy also depends on panel calibration, active-area mapping, and mechanical repeatability, not only on the controller’s 12-bit converter. This product record combines the manufacturer’s electrical characteristics with practical interface guidance, package details, and drop-in replacement analysis. It also organizes the key design trade-offs for engineers evaluating the ADS7845E against pin-compatible ordering variants and other touch-screen-controller families.
ADS7846E - 12-Bit 4-Wire Resistive Touch Screen Controller | TI
The Texas Instruments ADS7846E is a 4-wire resistive touch screen controller with an integrated 12-bit successive-approximation (SAR) ADC, 125 kHz conversion throughput and an SPI interface, housed in a 16-pin SSOP package. It runs from a single 2.7 V to 5.25 V analog supply and is specified across the -40 °C to +85 °C industrial temperature range. A touch screen controller is the interface IC that converts the resistive voltages produced by a four-wire glass or film panel into digital X and Y coordinates. Within the component hierarchy it sits as a touch screen controller within the family of data-converter ICs, whose core building block is a SAR ADC, and it ultimately belongs to the broader class of integrated circuits. Because the panel electrodes themselves form a variable resistive divider, the controller must both excite the panel and convert the resulting differential voltage accurately. Key features of the ADS7846E include the 12-bit ADC resolution, 125 kHz sampling capability, a direct battery measurement channel that lets a portable product sense its own supply voltage, an on-chip temperature sensor for panel and system compensation, and a programmable internal reference that removes the need for an external precision reference. According to Texas Instruments, the device is 100% pin-compatible with the industry-standard ADS7843 and drops into the same socket, so existing ADS7843 designs can be upgraded with software changes only. Internally the SAR core performs successive approximation on the differential voltage developed across the X+ and X− (or Y+ and Y−) electrodes. Differential sampling suppresses supply noise and panel-independent offsets, while the multiplexed AUX input extends the same converter to battery and temperature measurements. The digital side is a simple serial peripheral interface with chip select, data in, data out and clock, which keeps the pin count low and the host firmware straightforward. Typical applications include industrial human-machine interfaces, point-of-sale terminals, portable test and measurement instruments, medical infusion pumps, and battery-operated panel equipment where direct battery measurement and on-chip temperature sensing simplify system design. When designing around this controller, use the panel tail or PCB traces with a proper ground guard, keep the X/Y and AUX traces away from switching nodes and display backlight converters, and allow the internal reference and acquisition timing to settle before sampling. Pen-detection and interrupt handling should be configured so the host reads a settled conversion rather than polling blindly. This page combines manufacturer specifications, a drop-in comparison against the closest same-package alternatives, and practical layout and design guidance that goes beyond the electrical tables in the original datasheet.
ADS7852Y/2K - 12-Bit 8-Channel 500 kSPS ADC | Texas Instruments
Texas Instruments ADS7852Y/2K is a 12-bit, 8-channel, successive-approximation analog-to-digital converter with a 500 kSPS throughput rate, internal 2.5 V reference, and full 12-bit parallel output interface. The device is packaged in a 32-pin TQFP (PBS) package and accepts analog inputs from 0 V to twice the reference voltage, giving a nominal 0 V to 5 V input range. An ADC is a data-conversion IC that converts continuously varying analog voltages into numeric values for processing, measurement, or control. The ADS7852 belongs to the SAR ADC family, where a successive-approximation conversion cycle repeatedly tests internal capacitor voltages against the sampled input. This architecture provides deterministic conversion timing and works effectively when several channels must be digitized at moderate speed. The converter combines eight single-ended analog inputs with sample-and-hold circuits, a 2.5 V internal reference, and 12 parallel output lines. Typical power dissipation is 13 mW at a 500 kSPS throughput rate. Nap and sleep operating modes reduce power consumption to 2 mW, making the device useful in multiplexed industrial, instrumentation, and control systems that do not require continuous maximum-rate conversion. Its parallel interface exposes all 12 conversion bits simultaneously, which can simplify connection to an FPGA, CPLD, or other digital acquisition logic. The 500 kSPS aggregate throughput supports approximately 62.5 kSPS per channel when all eight inputs are scanned continuously. System timing must account for acquisition, conversion, output settling, and the interval between successive conversions so every parallel bus capture corresponds to the intended channel. Typical applications include factory data acquisition, process-control instrumentation, multichannel sensor measurement, industrial monitoring, and laboratory signal capture. Eight integrated inputs reduce the need for separate analog multiplexing circuitry, while the internal reference allows a self-contained measurement chain when precision requirements permit the fixed 2.5 V reference. PCB design should provide a continuous ground plane, short analog traces, and local decoupling close to the supply pins. Analog and digital return currents should remain separated to minimize coupling from the 12-bit output bus into the input circuitry. Use the manufacturer datasheet pin-description table and recommended application circuit when assigning tracks, supplying reference bypass capacitance, and defining conversion-control timing. This page combines the manufacturer specifications with practical interface, layout, application, and replacement guidance. It also identifies the exact package and operating characteristics engineers need when designing a parallel-output data-acquisition channel or deciding whether an alternative offers true pin-to-pin compatibility.
ADS7854IPW - Dual 14-Bit 1-MSPS SAR ADC | Texas Instruments
Texas Instruments ADS7854IPW is a dual, 14-bit, 1-MSPS successive-approximation analog-to-digital converter with simultaneous sampling, fully differential analog inputs, and a 16-pin TSSOP package. The device converts two differential input channels at the same time, making it suitable for phase-sensitive measurement, vibration analysis, instrumentation, and industrial control systems. Its two independently programmable reference sources support system-level gain calibration, while its flexible serial interface operates across a wide supply-voltage range. A SAR ADC is a successive-approximation register analog-to-digital converter. It compares the input voltage against a DAC-derived reference through a binary search process, producing a digital code after a fixed sequence of comparison cycles. The ADS7854 belongs to the SAR ADC hierarchy within analog-to-digital converters and data-converter ICs, where its fully differential inputs and simultaneous-sampling architecture distinguish it from multiplexed single-channel converters. The principal features of the ADS7854IPW are dual simultaneous sampling at 1 MSPS, 14-bit conversion resolution, two differential inputs, two individually programmable reference sources, and a flexible serial interface. Simultaneous sampling preserves the timing relationship between channels, which is important when calculating phase, gain, or transfer-function characteristics. Differential inputs also help reject common-mode noise when paired with suitable analog front-end circuitry. Each conversion uses an internal sampling-and-hold stage followed by successive-approximation conversion. This architecture provides predictable sampling behavior without the pipeline latency associated with some high-speed converter types. The two conversion results are transferred through the serial interface in a frame that preserves the relationship between the sampled channels. For system-level gain calibration, the programmable references can be set independently for the two analog channels. Typical uses include industrial data acquisition, vibration monitoring, motor-current analysis, power-system instrumentation, and dual-channel sensor measurement. The fully differential input architecture is especially useful when the source has low amplitude or when common-mode rejection is required. Designers must still provide suitable input filtering, reference bypassing, grounding, and source-impedance control to achieve predictable conversion performance. For layout, place input, reference, and decoupling components close to their associated pins, and use a quiet ground strategy for the analog section. Keep digital-clock and serial-data routing away from sensitive analog inputs. The serial-interface timing and the power-supply requirements should be evaluated together because converter noise and source impedance can influence code accuracy. This page combines the manufacturer’s device description with package, application, interface, and replacement guidance. It organizes the ADS7854IPW’s dual-channel SAR conversion characteristics into practical information for designing, sourcing, and maintaining industrial measurement systems.
ADS7861E - 12-Bit, 500 kSPS, 4-Channel Simultaneous ADC | TI
Texas Instruments ADS7861E is a dual, 12-bit, 500 kSPS analog-to-digital converter with four fully differential input channels arranged as two pairs for simultaneous signal acquisition in a 24-pin SSOP (DBQ) package. The converter combines two successive-approximation ADCs with a 2+2-channel architecture, allowing two analog pairs to be sampled simultaneously. An ADC is a mixed-signal semiconductor that converts an analog voltage into a digital code. Within the broader hierarchy of data-converter ICs, the ADS7861E belongs to the successive-approximation ADC family and is used for data acquisition, instrumentation, industrial control, and signal measurement. Its fully differential inputs preserve differential signal integrity between the sample-and-hold amplifier and the ADC input while providing 80 dB common-mode rejection at 50 kHz. The principal specifications include 12-bit resolution, a 500 kSPS conversion rate, four fully differential inputs, two simultaneous-sampling ADC channels, and a 24-pin SSOP package. The operating temperature range shown by the manufacturer ordering information is -40°C to +125°C. These characteristics make the device suitable for systems that require simultaneous acquisition, such as three-phase motor monitoring, vibration analysis, and multichannel process-control instrumentation. Each ADC uses a successive-approximation conversion architecture, providing a practical balance between conversion speed, resolution, power consumption, and implementation complexity. The four inputs are grouped into two pairs, so corresponding channels can be captured together. This arrangement is useful when phase, timing, amplitude, or ratio relationships between paired signals must be preserved during acquisition. Typical applications include industrial motor drive and inverter control, power-system monitoring, vibration and condition-monitoring equipment, process-control loops, and precision instrumentation. Differential input architecture is particularly useful in environments where common-mode noise can otherwise obscure the wanted signal. System designers should still allocate suitable analog filtering and provide compliant input and reference circuitry. The principal design consideration is signal integrity. Input components, routing, grounding, reference stability, and digital-interface timing directly affect conversion performance. The verified sources provide the ADC family, package, resolution, throughput, channel arrangement, common-mode rejection, operating-temperature range, and a starting distributor price; additional electrical limits and a complete pin map must be obtained from the manufacturer datasheet before design release. This page combines verified manufacturer and distributor information, documented drop-in family alternatives, parameter comparisons, and practical selection guidance to support engineering decisions beyond a basic distributor listing.