Amplifier ICs
بەرهەمەکان (3,200+)
MC3403PW - Quad 1MHz 30V Op Amp | Texas Instruments
The Texas Instruments MC3403PW is a four-circuit general-purpose operational amplifier with a 1 MHz gain-bandwidth product, a 30 V maximum supply rating, and operation from -25°C to 85°C. The device is packaged in a 14-pin TSSOP, making MC3403PW suitable for compact analog signal-processing circuits that require four amplifiers in one package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while providing high input impedance, low output impedance, and stable operation with feedback. The MC3403 family combines four amplifiers with a low-power class AB output stage, true differential inputs, internal frequency compensation, and short-circuit protection. It sits within the operational-amplifier category as a general-purpose amplifier for instrumentation, control, and signal-conditioning systems. Key characteristics include four independent amplifier channels, a 1 MHz gain-bandwidth product, support for single and dual supplies, a true differential input stage, and internal frequency compensation. The -25°C to 85°C operating-temperature range supports industrial and commercial equipment when the surrounding system provides suitable thermal conditions. Its 14-pin TSSOP also reduces board area compared with four separate single-amplifier packages. Each amplifier is frequency compensated, so applications using voltage gain do not require an external compensation network. The class AB output stage is designed to support linear operation while the short-circuit-protection feature improves resilience in feedback-controlled circuits. Because the device is intended for general-purpose signal amplification, external precision resistors, compensation, output isolation, and protection components may still be needed when driving loads, extending bandwidth, or meeting application-specific noise and accuracy targets. Typical uses include low-frequency sensor conditioning, feedback-control loops, current-voltage signal conversion, analog summing and difference circuits, and four-channel buffer arrangements. The integrated quad structure is especially useful where several independent analog paths must fit on a compact PCB, such as industrial measurement modules, instrumentation interfaces, and embedded control systems. PCB layout should keep feedback resistors close to their corresponding amplifier pins, provide a solid ground return, and route high-impedance input nodes away from switching nodes. Decoupling capacitors should be placed close to the supply pins. Designers should verify output swing, input common-mode range, load capability, stability, and supply limits for the intended operating points using the manufacturer datasheet. This page combines the manufacturer product information, distributor product records, package details, application guidance, and available same-footprint comparison information to support component selection and board-level planning. It also identifies which electrical parameters require confirmation from the complete Texas Instruments datasheet before final design release.
MC34071D - 44V Single-Supply Operational Amplifier | onsemi
The onsemi MC34071D is a single-supply operational amplifier designed for operation from 3.0 V to 44 V, with a 4.5 MHz gain-bandwidth product and a 13 V/µs slew rate. The device is packaged in an 8-pin SOIC and uses bipolar fabrication rather than JFET input devices. Its combination of high bandwidth, fast slew rate, and a wide supply-voltage range makes it suitable for industrial instrumentation, signal conditioning, data acquisition, and control systems that operate from elevated supply voltages. An operational amplifier is a high-gain differential amplifier used to amplify small input signals, buffer sensors, drive analog stages, and implement feedback-control networks. The MC34071 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Although the MC34071 family can operate from split supplies, it is particularly suited to single-supply operation, which simplifies circuits whose signal reference is close to the lower supply rail. The family provides 4.5 MHz of gain-bandwidth product, a 13 V/µs slew rate, and fast settling time without using JFET device technology. The specified single-supply performance is defined at 5.0 V. The amplifiers are also functional at 3.0 V at 25°C, although bandwidth, slew rate, DC gain, and other parameters may change in that operating region. This distinction is important when designing at the minimum supply voltage. The bipolar process supports operation from a single 5.0 V supply or higher while accommodating input and output signals referenced toward ground. The wide 44 V maximum supply rating provides additional operating headroom for industrial systems while retaining the usual bipolar advantages of low input-voltage noise and accurate behavior around the output operating point. Designers should still use the manufacturer datasheet limits for input common-mode range, output swing, supply current, and stability with the selected gain and load. Typical uses include sensor-interface amplifiers, low-side current measurement, industrial control loops, audio and communications signal conditioning, active filtering, and general-purpose analog processing. Because the amplifier is optimized for single-supply operation, input and output signal levels must remain inside the datasheet common-mode and output-swing limits. Input common-mode limits depend on supply voltage and gain, so a signal that is valid at 5 V may not remain valid at 3 V. The main design consideration is supply headroom. Use decoupling close to the supply pins, verify that the selected feedback network remains stable at the intended noise gain, and check output-current capability for the load and output-voltage conditions. The MC34071 is not intended to replace a rail-to-rail input or output amplifier where signals exceed its specified common-mode or swing limits. This page combines verified manufacturer and distributor information with practical selection criteria, sourcing guidance, and verified same-package alternatives. It highlights where the MC34071D fits, where its non-rail-to-rail architecture requires careful signal-range review, and which replacement MPNs should be checked against the full datasheet before substitution.
MC34071DG - 4.5MHz, 13V/us Single Op Amp | onsemi
onsemi MC34071DG is a single general-purpose operational amplifier with a 4.5 MHz gain-bandwidth product, 13 V/us slew rate, and single-supply operation from 3.0 V to 44 V. The device is manufactured in bipolar technology and is packaged in an 8-pin SOIC. An operational amplifier is an active analog component that uses high-gain feedback to amplify voltage differences between its input terminals. The MC34071 family combines wide supply-voltage tolerance, high bandwidth, and fast slew rate in a general-purpose amplifier, making it suitable for signal conditioning, instrumentation, filtering, and feedback-control circuits. Its common-mode input range includes ground potential, allowing practical operation from a single positive supply. Key specifications include 4.5 MHz gain-bandwidth product, 13 V/us slew rate, fast settling time, and bipolar fabrication without JFET input devices. The single amplifier supports both split-supply and single-supply configurations, while its input common-mode capability makes it useful in systems where signals remain close to the negative supply rail. The MC34071 is designed for applications requiring higher speed than conventional general-purpose amplifiers. Its 4.5 MHz bandwidth supports moderate-frequency signal paths, and the 13 V/us slew rate provides faster large-signal response than many standard precision amplifiers. The bipolar process also provides a conventional input-bias-current characteristic of approximately 100 nA for the listed device family. Typical applications include low-level signal amplification, active filters, sensor conditioning, audio preamplifier stages, and general feedback amplifiers. The device can also serve in industrial control and instrumentation circuits where a single supply and operation near ground are important. Split-supply operation remains possible when the circuit requires a bipolar output range. When designing around the MC34071DG, check input and output voltage limits against the selected supply, including the effects of transient overshoot. Keep feedback compensation values consistent with the closed-loop gain, and place input and output components close to the device pins. Verify the final design for stability across the intended gain, temperature, and load range. This page consolidates the manufacturer product information, distributor availability references, cross-reference candidates, and application guidance for engineers evaluating the MC34071DG. It highlights the electrical envelope, package details, replacement considerations, and practical design decisions needed to determine whether this single-supply bipolar amplifier fits a new or existing circuit.
MC34071P - 3-44V Single Operational Amplifier | onsemi | 8-DIP
The onsemi MC34071P is a single operational amplifier designed for single-supply operation from 3.0 V to 44 V, with an 8-pin DIP package. It is a general-purpose bipolar operational amplifier intended for instrumentation, buffering, signal conditioning, and control applications where a wide supply range and single-supply operation are useful. The device is specified for a 5.0 V single-supply condition while remaining functional down to 3.0 V at 25°C, although bandwidth, slew rate, and DC gain can change in that lower-voltage region. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare an inverting input with a non-inverting input. The MC34071P provides one amplifier circuit in an 8-DIP package, placing it within the hierarchy of operational amplifier, analog amplifier, and integrated circuit. Its single-supply capability simplifies circuits that operate from batteries, industrial control rails, test equipment, and other systems that do not provide a centered or negative supply. The MC34071P is associated with a 5 mV input offset voltage specification in distributor listings and uses quality bipolar fabrication in the onsemi MC33071, MC34071, and related family. The family includes dual and quad versions for designs that require multiple amplifier channels, but channel count and package differ when comparing those family members with the single MC34071P. The 8-DIP package is a through-hole package with a nominal 0.300-inch, 7.62 mm lead pitch, making it suitable for conventional PCB layouts and prototype boards. Typical uses include sensor signal conditioning, low-frequency active filtering, industrial instrumentation, audio and communications support circuits, and general voltage amplification. Because the amplifier can operate from a single supply, the input and output signal ranges must be checked against the supply rails. Designers should also account for input common-mode limits, output swing, bias-current effects, noise, stability, and the power dissipation produced by the selected supply voltage and load. The MC34071P is most appropriate when a through-hole single op amp is preferred and the design needs wide single-supply headroom. Its counterpart MC34071APG is the most directly identified cross-reference candidate in the available information. Before substituting any part, confirm the complete pinout, electrical limits, common-mode behavior, output swing, and stability requirements against the target circuit. This page consolidates the verified onsemi datasheet information, distributor package identification, and cross-reference findings into a practical component record. The key engineering distinction is not simply the 3.0 V to 44 V supply capability, but the combination of a single amplifier, bipolar implementation, through-hole 8-DIP construction, and the need to design the signal path around single-supply input and output limits.
MC34071PG - 44V Single Op Amp, 4.5MHz | onsemi
The onsemi MC34071PG is a single operational amplifier with a 3 V to 44 V single-supply operating range, 4.5 MHz gain-bandwidth product, and 13 V/µs slew rate, supplied in an 8-pin PDIP package. It is designed for general-purpose instrumentation and signal-conditioning applications where wide supply-voltage tolerance, fast slew, and a conventional bipolar input stage are useful. An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify or buffer signals in electronic systems. The MC34071 belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and signal-chain semiconductors. Its wide supply range allows it to operate from conventional 5 V and 12 V rails as well as higher industrial voltage systems, although the complete circuit must remain within the device's absolute maximum ratings. Key characteristics include a 4.5 MHz gain-bandwidth product, 13 V/µs slew rate, single-ended input configuration, and a general-purpose amplifier design. The manufacturer describes the MC34071 series as using quality bipolar fabrication and innovative design concepts. The bipolar approach supports conventional op-amp behavior and is useful in applications requiring signal amplification, buffering, active filtering, and general analog control functions. The device's fast settling performance and 13 V/µs slew rate make it more responsive than slow precision-oriented amplifiers. This is beneficial for instrumentation and feedback loops that need to follow changing input waveforms. Designers should still account for input and output voltage limits, common-mode range, output-current capability, supply decoupling, and stability when driving capacitive or nonlinear loads. Typical uses include industrial process-control instrumentation, sensor signal conditioning, audio and communications support circuits, active filters, voltage followers, and general laboratory measurement equipment. Because the MC34071PG is a through-hole PDIP device, it is especially convenient for prototyping, educational systems, repair work, and applications where socketed or manually soldered assembly is acceptable. For reliable operation, decouple the supply pins close to the device and provide stable reference and feedback paths. Avoid forcing the output beyond its rated output-voltage swing, and check the input common-mode range over the complete operating range. Use the manufacturer pin description and electrical characteristics tables when assigning PCB nets and designing around input offset, bias current, supply current, and output-drive limits. This product page combines manufacturer specifications, package information, design guidance, drop-in alternatives, and a parameter-by-parameter comparison to support faster component selection and PCB-level planning for MC34071PG-based analog circuits.
MC34072D - 4.5 MHz Single Op Amp, 3-44 V | onsemi
The onsemi MC34072D is a single, general-purpose operational amplifier optimized for wide supply-voltage operation. It provides a 4.5 MHz gain-bandwidth product, a 13 V/µs slew rate, and operation from 3.0 V to 44 V in an 8-pin SOIC package. The MC34072D also supports fast settling to 0.1% within 1.1 µs and an input common-mode range that includes ground. An operational amplifier is a high-gain, active differential amplifier whose inverting and non-inverting inputs control an output voltage. Within the broader semiconductor hierarchy, an operational amplifier is an analog integrated circuit used for signal conditioning, current-to-voltage conversion, feedback control, filtering, and buffered drive stages. The MC34072 belongs to a family of single-supply, bipolar operational amplifiers designed to combine broad rail-voltage capability with relatively high bandwidth. The principal features of the MC34072D include 4.5 MHz gain bandwidth, 13 V/µs slew rate, 1.1 µs settling time to 0.1%, and a low 3.0 mV maximum input offset voltage for the A-suffix grade. It operates from 3.0 V to 44 V, and its input common-mode range includes the negative supply rail, which simplifies single-supply signal-chain design. Output swing extends from approximately -14.7 V to +14 V under the conditions listed by the manufacturer. The bipolar fabrication of the MC34071, MC34072, and MC34074 families supports the combination of wide bandwidth, high slew rate, and common-mode operation that extends to ground. This characteristic is particularly useful when signals remain close to the lower supply rail or when the amplifier must process bipolar sensor signals from a unipolar-powered acquisition circuit. Input bias current and noise specifications should be checked against the source impedance in the selected gain configuration. Typical uses include low-voltage sensor interfaces, industrial process-control loops, audio preamplifier stages, active filters, and general instrumentation. Its 3.0 V to 44 V operating range also makes it suitable for industrial systems that operate from a 5 V, 12 V, 24 V, or higher regulated rail. The device can be used where the required signal bandwidth remains below the amplifier's closed-loop bandwidth for the selected noise-gain setting. Designers should verify output-current capability, output-swing limits, input common-mode range, and stability at the intended gain and capacitive-load conditions. Keep feedback-loop layouts compact, place compensation or decoupling components close to the relevant pins, and avoid operating near the output-swing limits when driving low-impedance downstream loads. This page consolidates the MC34072D electrical characteristics, confirmed ordering variants, package information, and application guidance with comparison notes for engineers evaluating drop-in operational-amplifier alternatives.
MC34072DG - Dual 44V Op Amp | onsemi | Industrial Amplification
onsemi MC34072DG is a dual general-purpose operational amplifier optimized for single-supply operation from 3.0 V to 44 V. It provides two amplifiers in an 8-pin SOIC package, with 4.5 MHz gain-bandwidth product, 13 V/µs slew rate, and 5 mV typical input offset voltage. The part combines bipolar fabrication with a design that avoids JFET input transistors. An operational amplifier, or op amp, is a voltage-feedback analog IC that amplifies the difference between its inverting and non-inverting inputs. The op amp belongs to the broader hierarchy of amplifier IC, analog IC, semiconductor, and signal-conditioning component. Its gain, input offset, slew rate, common-mode range, output swing, and noise determine how accurately it can process low-level signals in instrumentation, control, sensing, and signal-conditioning circuits. The MC34072 family is particularly useful when a circuit must operate from a single positive supply while accepting signals near ground. Its 3.0 V to 44 V supply range provides flexibility for industrial control systems, test equipment, sensor interfaces, and power-supply feedback networks. The 4.5 MHz gain-bandwidth product supports higher-frequency closed-loop operation than a basic precision amplifier, while the 13 V/µs slew rate improves large-signal response. Two independent amplifiers are integrated in one 8-pin SOIC, reducing component count and board area. MC34072DG is a commercial-temperature, standard general-purpose amplifier. The dual configuration provides separate input and output pins for channels A and B. Typical applications include buffer stages, active filters, transducers, current sensing, sample-and-hold circuitry, comparators, and general-purpose signal conditioning. The dual channel can also support independent signal paths, cascaded stages, or two channels of a differential or multichannel measurement system. Single-supply operation requires careful attention to the input common-mode range and output swing. Inputs must remain inside the amplifier's valid common-mode region, and the output must be biased appropriately when processing signals centered near 0 V. Decoupling capacitors should be placed close to the supply pins, while feedback components should be kept compact to minimize parasitic coupling and preserve the intended bandwidth and stability behavior. This page combines the manufacturer product information, exact MC34072DG orderable-part listings, package information, replacement references, application guidance, and engineering design notes. It also distinguishes package-compatible ordering variants from the dual MC33072DG option so that form, fit, function, and qualification requirements can be checked before PCB substitution.
MC34072PG - Dual 44V Op Amp with 13V/us | onsemi
onsemi MC34072PG is a dual general-purpose operational amplifier with a 3 V to 44 V supply range, 4.5 MHz gain-bandwidth product, and 13 V/us slew rate in an 8-pin PDIP package. The device provides two amplifiers with single-ended outputs and uses quality bipolar fabrication without JFET input technology. An operational amplifier is an amplifier IC that uses high-gain differential feedback to control an output voltage. The MC34072 family belongs to the broader operational amplifier, analog IC, and semiconductor hierarchies. It can operate from split supplies or a single supply and is particularly suited to circuits requiring higher supply tolerance than typical low-voltage rail-to-rail amplifiers. The 4.5 MHz gain-bandwidth product supports useful closed-loop bandwidth at practical gain settings, while the 13 V/us slew rate allows outputs to change quickly without requiring JFET inputs. The manufacturer lists a 5 mV input offset-voltage figure for the commercial-temperature MC34072PG, and its bipolar construction is suited to general-purpose analog signal conditioning. The MC34072 series combines precision bipolar performance with relatively high operating-voltage capability and fast settling behavior. Each amplifier can serve as an inverting or non-inverting stage, and the two independent channels allow simultaneous processing of related signals. This architecture is useful when a board needs one amplifier for filtering and another for buffering or gain control. Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, transducer amplifiers, feedback-control loops, and general instrumentation powered from industrial supply rails. The 44 V maximum supply also makes the device relevant to legacy 24 V control systems, provided the selected operating voltage and dissipation remain within the device ratings. Place bypass capacitors close to the supply pins and route feedback components away from input and output traces to reduce oscillation risk. Confirm output swing, input common-mode range, load current, and thermal dissipation for each amplifier channel. Dual packages require evaluation of channel-to-channel behavior, not only the aggregate device rating. This product page combines the MC34072PG operating characteristics with engineering-focused pin, packaging, replacement, and design guidance. It supports faster selection by placing verified headline specifications beside the practical constraints that determine whether the dual amplifier can operate safely in a target circuit.
MC34119D - Low-Power Class AB Audio Amplifier | NXP
The NXP MC34119D is a low-power, mono Class AB audio amplifier integrated circuit designed primarily for telephone equipment, including speakerphones. It operates from a 2 V minimum supply, supports a nominal range of 2 V to 16 V or ±1 V to ±8 V, and provides differential speaker outputs to increase usable output swing at low supply voltages. The device is supplied in an 8-pin SOIC package according to the distributor product listing. An audio amplifier is an integrated circuit that accepts a low-level analog audio signal and delivers enough current and voltage to drive a speaker or another acoustic transducer. The MC34119 belongs to the Class AB amplifier category, where the output transistors conduct during the signal cycle for improved efficiency than a continuously biased Class A design. Its telephone-oriented architecture supports portable and line-powered equipment where low supply voltage and compact implementation are important. The verified feature set includes a shutdown function, a single mono output channel, and differential speaker outputs. Differential outputs are particularly useful in telephone and speakerphone designs because they increase output swing into a differentially connected transducer. The manufacturer datasheet also identifies a 2.0 V minimum supply, allowing operation from low-energy source rails. The Class AB output stage is intended to balance output capability against power consumption in compact audio systems. MC34119D applications include telephone speakerphones, compact voice terminals, intercom equipment, and other low-voltage audio products. In these systems, the amplifier converts a microphone or line-level signal into a differential drive capable of energizing a small speaker. Designers should account for the external output-coupling capacitors shown in the manufacturer application circuit when connecting a speaker, and should verify the shutdown-control polarity and timing before sequencing the device. The most important design consideration is ensuring that the supply, input signal, output network, and speaker load remain within the limits defined by the manufacturer datasheet. Because the target is a legacy low-power audio amplifier, purchasing decisions should also account for lifecycle status, stock, and long-term sourcing rather than assuming availability from an active-production family. This page consolidates the verified package, supply-voltage, amplifier-class, shutdown, and differential-output information with practical selection guidance. It also distinguishes confirmed facts from parameters that require confirmation in the original MC34119 manufacturer datasheet, helping engineers evaluate MC34119D without relying on incomplete distributor summaries.
MC34119P - 2-16V Mono Class AB Audio Amp | NXP
NXP MC34119P is a low-power, 1-channel Class AB audio amplifier IC designed for telephone equipment, including speakerphones, with a 2 V to 16 V supply range and differential speaker outputs in an 8-pin DIP package. It provides a practical solution where low supply voltage, low quiescent current, and efficient single-speaker drive are required. The available ordering information identifies the device as an NXP USA Inc. 8-PDIP mono audio amplifier. An audio amplifier IC is a semiconductor that accepts a small audio signal and delivers enough voltage and current to drive a loudspeaker or other audio transducer. A Class AB amplifier combines the low crossover distortion of class-A operation with improved efficiency compared with a continuously biased class-A stage. In the MC34119P, differential speaker outputs are intended to maximize output swing at low supply voltages, making the device especially relevant to compact telephone and communications equipment. The MC34119P operates from 2.0 V to 16 V, as documented in the retrieved manufacturer and distributor information. Its typical quiescent supply current is 2.7 mA for battery-powered designs, while shutdown reduces the typical quiescent current to 65 µA. A chip-disable input provides a direct means of placing the amplifier in its low-power state. These features allow the amplifier to remain useful when system power is constrained by a telephone line or battery source. Its architecture uses one Class AB output channel and differential speaker outputs rather than a conventional single-ended output arrangement. Differential drive can provide greater useful voltage swing into the speaker for a given supply, which is important at the 2 V minimum supply. This is a system-level advantage in speakerphone products where loudness and battery efficiency must coexist. Exact continuous output power, output impedance, gain settings, and distortion limits were not included in the retrieved source snippets and must be confirmed in the full manufacturer datasheet before final design sign-off. Typical uses include telephone speakerphones, telephone-line powered communications products, small intercom stations, compact voice monitors, and portable low-voltage audio equipment. The device is also suitable where standby consumption matters, because the shutdown function can isolate the amplifier from the active signal path. For these applications, the 2 V minimum operating voltage and differential output capability align particularly well with low-power, single-speaker systems. The primary design consideration is output-device and load compatibility. Engineers should verify speaker impedance, output power at the available supply voltage, thermal conditions, gain configuration, bypass capacitors, and shutdown logic against the complete MC34119 datasheet. Because the supplied text identifies an 8-DIP footprint but does not enumerate individual terminal functions, the pin assignment and exposed circuit details should not be inferred solely from this page. This product page consolidates the verified MC34119P package, voltage, topology, shutdown, and low-power information with practical application guidance, sourcing considerations, and honest drop-in replacement analysis. Its key value is separating confirmed MC34119P characteristics from unverified specifications and avoiding unsupported claims about substitutes that may require different EMI performance or pin behavior.
MC34184M - Low-Power Quad JFET Op Amp | onsemi
The onsemi MC34184M is a low-power, quad, JFET-input operational amplifier characterized by 210 uA of supply current per amplifier, a 4.0 MHz gain-bandwidth product, and a 10 V/us slew rate. Housed in onsemi's legacy MC34184M package, the device combines low input bias current with high input resistance for instrumentation, signal-conditioning, and low-frequency analog systems. A JFET-input operational amplifier is a voltage-amplifier device whose input stage uses junction field-effect transistors. This input architecture provides high input resistance and low input bias current while supporting relatively low supply-current operation. Within the power-management and analog-signal hierarchy, the MC34184M belongs to the operational-amplifier family and functions as a high-impedance buffer or closed-loop gain stage between sensors, transducers, analog switches, and downstream conversion or control circuitry. The primary performance characteristics of the MC34184M include a 4.0 MHz gain-bandwidth product, 10 V/us slew rate, and approximately 210 uA of supply current per amplifier. Its JFET input stage provides high input resistance, low input offset voltage, and high open-loop gain according to the Motorola MC34184 datasheet. These characteristics make the amplifier appropriate for precision current-voltage conversion, low-level signal amplification, active filtering, and feedback networks operating at low or moderate frequencies. The family architecture also supports practical instrumentation requirements because low input bias current reduces disturbance of high-impedance sources. A high gain-bandwidth product allows useful closed-loop bandwidth above the audio range when configured with conventional compensation and suitable external resistors. The 10 V/us slew rate improves handling of moderately fast signal edges, although the 4.0 MHz bandwidth places the device in the general-purpose precision-amplifier class rather than the high-speed operational-amplifier class. Typical applications include bridge-sensor signal conditioning, biomedical instrumentation, photodiode and phototransistor amplifiers, audio preamplification, active filters, sample-and-hold stages, and low-frequency closed-loop control loops. In each case, the amplifier should be evaluated for input common-mode range, output swing, noise, offset, stability, and supply compatibility under the actual operating conditions. Designers should verify the package dimensions, pin numbering, electrical limits, and common-mode range against the manufacturer documentation before layout. Input and feedback resistors must also be selected for low thermal noise and acceptable bias-current error. Bias compensation may be useful when source resistance is high enough that input bias current produces a material offset across the source impedance. This page organizes the core MC34184M electrical characteristics, practical application guidance, comparison parameters, and design considerations into one engineering-focused reference. It supports early architecture selection while preserving the need to verify production details, lifecycle commitments, and assembly-specific information with the manufacturer before releasing a design.
MC3461L - Dual Current Sense Amplifier | Motorola | CDIP-16
The Motorola MC3461L is a dual current-sense amplifier in a 16-pin CDIP package, with two amplifier circuits for measuring current across low-value shunt resistors. The verified distributor data identifies the device as a high-speed NMOS/MECL current-sense amplifier, while detailed electrical limits, gain values, common-mode range, supply voltage, and temperature ratings are not included in the supplied records and therefore remain unconfirmed. Its instrumentation-amplifier classification places it among amplifier ICs used for power-conversion monitoring, motor control, battery management, and power-supply feedback. A current-sense amplifier is a specialized voltage-feedback amplifier that develops a measurable output voltage from the small differential voltage created by current flowing through a shunt resistor. The MC3461L contains two circuits, allowing one packaged device to monitor two independent current paths when the circuit board has sufficient isolation and the operating conditions of both channels are compatible. The 16-CDIP mechanical format is a through-hole ceramic dual in-line package intended for legacy industrial, instrumentation, and telecommunications equipment. The MC3461L's two-circuit architecture reduces component count compared with two separate single amplifiers, while its small shunt-generated differential signal supports compact sensing layouts. However, stable measurement depends on selecting an appropriate shunt, keeping Kelvin connections narrow and symmetrical, and observing the amplifier's common-mode and output limits. Because those numerical limits are absent from the verified excerpts, designers should consult the complete manufacturer datasheet before finalizing resistor values, gain configuration, supply rails, or production tolerances. The MC3461L is suitable for power-supply current monitoring, battery charge and discharge sensing, motor-control feedback, industrial process-control systems, and communications equipment. In these applications, the amplifier converts bidirectional or unidirectional shunt current into a voltage suitable for an ADC, controller, comparator, or protection circuit. The exact input polarity, output reference arrangement, and permissible common-mode voltage must be verified from the full datasheet before layout sign-off. A practical design begins by placing the shunt and amplifier in the same high-current path, routing the sense traces as a tightly coupled differential pair, and grounding the unused inputs or amplifier according to the manufacturer's recommended configuration. Decoupling capacitors should connect directly to the supply pins, and the output must remain within the device's verified output range. PCB creepage, clearance, copper heating, and Kelvin-trace geometry are as important as the IC choice in a high-current design. This page combines verified distributor identity and availability information with clearly marked engineering gaps, practical application context, and design guidance. It does not infer missing electrical specifications from the MC3461 family name, so procurement, electrical, and package decisions should be completed against the official datasheet and current authorized-channel inventory.
MC3476P1 Low-Cost Programmable Operational Amplifier | onsemi
The onsemi MC3476P1 is a low-cost, programmable operational amplifier designed for general-purpose analog signal conditioning. The device is associated with an 8-pin DIP package, and its core features include low power consumption, high input impedance, and a programmable operating point that allows engineers to adapt the amplifier to different bias and performance requirements. The MC3476P1 is therefore useful in applications requiring adjustable amplifier behavior rather than a fixed, conventional op-amp configuration. An operational amplifier is a voltage-controlled differential amplifier with very high open-loop gain. Its two inputs are the inverting input and non-inverting input, while the output is controlled by feedback in most practical circuits. The programmable family represented by the MC3476P1 adds a bias-current control function, allowing the operating current and associated performance to be adjusted externally. This makes the device more flexible than a fixed-bias amplifier when system designers need to balance power consumption, bandwidth, output drive, and signal-source loading. The MC3476P1 is described by its manufacturer as a low-cost selection of the MC1776 programmable operational-amplifier family. Its low power consumption is useful in battery-powered, portable, and low-power instrumentation systems. High input impedance helps reduce loading on high-impedance signal sources, which can help preserve signal amplitude and reduce input-stage interaction. The programmable bias architecture also gives designers a way to tailor performance after considering source impedance, gain, bandwidth, and acceptable supply current. Typical analog uses include sensor-interface stages, low-frequency instrumentation, buffer and gain stages, active filters, and signal-conditioning blocks in industrial or embedded control systems. The device can be used where a general-purpose amplifier is sufficient and adjustable operating current is valuable. Designers should review the manufacturer datasheet for guaranteed input-voltage range, output-swing limits, supply-current ranges, gain-bandwidth behavior, offset voltage, input bias current, and package details before finalizing a design. A key implementation consideration is the connection of the programmable-bias circuitry. Incorrect resistor values, unsuitable bypassing, or operation outside the specified supply and common-mode ranges can reduce stability or prevent expected output behavior. Keep the input network and feedback components close to the device, use a stable bypass capacitor at the supply pins, and verify noise, settling time, and output-swing requirements with the actual source impedance and load. This page combines the manufacturer-linked product identity, documented package information, application guidance, and practical design considerations for engineers evaluating the MC3476P1. Because the exact electrical limits and pin assignments are not reproduced in the cited search results, consult the original MC3476P1 datasheet for authoritative values before schematic release, PCB layout, or production qualification.
MC4558CP1 - Dual 2.5MHz Wide-Bandwidth Op-Amp DIP-8 | onsemi
The onsemi MC4558CP1 is a monolithic dual wide-bandwidth operational amplifier housed in an 8-pin PDIP (DIP-8) through-hole package, internally compensated and pin-compatible with the industry-standard 1458/4558 pinout. According to the onsemi datasheet, each of the two on-chip amplifiers delivers a unity-gain bandwidth of 2.5 MHz (C-grade) and 2.0 MHz (AC-grade), with the MC4558AC variant specifically guaranteed to the 2.5 MHz figure. The device targets cost-sensitive general-purpose analog signal-conditioning roles that benefit from higher small-signal bandwidth than the legacy 1458 family. What is an operational amplifier (op-amp)? An op-amp is a high-gain DC-coupled differential voltage amplifier that uses external feedback components to set closed-loop behavior, and dual op-amps integrate two such amplifiers in one package. In the signal-chain taxonomy, op-amps sit beneath active filters, instrumentation amplifiers, and comparators, and above discrete transistors in the analog IC hierarchy. The MC4558 series belongs to the bipolar-junction-transistor (BJT) input, voltage-feedback amplifier class, which combines low input bias current, moderate noise, and rail-to-rail-free swing within headroom-limited supply rails. Key features include no requirement for external frequency compensation, internal latch-up immunity, large common-mode and differential input voltage ranges, matched gain and phase between the two on-chip amplifiers, low input noise, and parameter tracking over temperature. The DIP-8 plastic package supports hand-soldered prototyping and educational lab use where through-hole leads are preferred over SMT. Operating supply is typically ±15 V dual or +30 V single-ended, and the part is specified for the commercial 0 °C to +70 °C range on the C-suffix and -40 °C to +85 °C on the AC-suffix variants. The MC4558CP1 architecture is a classic bipolar voltage-feedback topology: a PNP input differential pair feeds a current-mirror active load, driving a high-gain second stage with class-AB push-pull output. The internal compensation capacitor rolls off open-loop gain at roughly 6 dB/octave above the dominant pole, which is why the unity-gain bandwidth exceeds the 1 MHz figure of the older 1458 by a factor of three. Designers can therefore use the part in unity-gain buffers without external compensation components. Typical applications include audio pre-amplifiers and tone-control stages, active filters and equalizers, transducer signal-conditioning front-ends, integrators, comparators, and general-purpose DC amplifiers in industrial controls. The DIP-8 package also makes the MC4558CP1 a preferred teaching reference for electronics curricula and breadboard prototyping. When designing with this op-amp, observe the supply headroom limits and pair the part with appropriately rated supply bypass capacitors placed within 1 cm of the VCC/VEE pins to maintain stability and minimize channel crosstalk. The matched amplifier pair simplifies layout when both channels must share identical bandwidth and phase response, e.g., in stereo audio front-ends. This page synthesizes distributor pricing, drop-in alternatives from the 1458/4558 family, and practical design notes not consolidated in any single manufacturer datasheet.
MCP4342-503E/ST - 50kΩ Quad 7-Bit SPI Digital Potentiometer | Microchip
The Microchip Technology MCP4342-503E/ST is a non-volatile, 7-bit (129 taps) quad-channel digital potentiometer with 50 kΩ end-to-end resistance, SPI-compatible interface, and on-chip EEPROM, housed in a 14-pin TSSOP (ST) package. It integrates four independent rheostat/potentiometer channels, each with 128 resistive elements plus a wiper tap, giving 129 programmable steps per channel and approximately 3.9 % nominal resistor network resolution. A digital potentiometer (often abbreviated "digiPOT") is a digitally controlled variable resistor that emulates the behavior of a mechanical potentiometer or trim pot. In the broader component taxonomy, a digital potentiometer belongs to the data-conversion / signal-conditioning family and serves as a programmable resistor network used for gain control, offset trimming, LCD contrast adjustment, and sensor calibration. Unlike mechanical pots, it is set through a serial command and retains its wiper position across power cycles when non-volatile memory is present, as in the MCP4342 family. Key features include a wide operating supply range of 1.8 V to 5.5 V, low typical quiescent current of around 1 µA at 5 V, ±20 % end-to-end resistance tolerance, SPI serial interface (modes 0,0 and 1,1) up to 10 MHz, and wiper settings stored in non-volatile EEPROM so the part powers up in its last programmed state. Each channel supports both potentiometer and rheostat modes, and a software-controlled wiper lock register is available to prevent unintended changes. The MCP4342-503E/ST uses a chain of 128 polysilicon resistive elements with CMOS analog switches steered by a 7-bit decoder. The wiper switches between taps with break-before-make action, the EEPROM cell uses the same charge-pump architecture as Microchip's PIC microcontrollers, and the SPI peripheral supports both byte and sequential commands including read, write, increment, and decrement of the wiper position without rewriting the EEPROM. Typical applications include audio equipment volume and tone control, LCD display contrast and brightness trimming, sensor calibration in industrial and instrumentation systems, programmable gain amplifiers, and any general-purpose mechanical-trim-pot replacement where software-driven or remote adjustment is desired. When laying out this part, place the 0.1 µF VDD bypass capacitor as close as possible to pin 14, keep analog signal traces short, and avoid running digital lines directly beneath the resistor network. For rheostat-mode operation, connect the unused terminal to the wiper to minimize parasitic capacitance effects. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten the selection cycle and reduce BOM risk.
MCP4361-503E/ST - 50kΩ Quad 8-bit SPI Digital Potentiometer | Microchip
The Microchip Technology MCP4361-503E/ST is a non-volatile, quad-channel, 8-bit (257-tap) digital potentiometer with 50 kΩ end-to-end resistance and an SPI-compatible serial interface, housed in a 20-pin TSSOP package. It integrates four independent rheostat/potentiometer channels with on-chip EEPROM wiper storage, operates from a single 2.7 V to 5.5 V supply, and supports a wide industrial temperature range of -40 °C to +125 °C. The device features ±20 % end-to-end resistance tolerance, a typical wiper resistance of 75 Ω, and a temperature coefficient of 150 ppm/°C. A digital potentiometer (digipot) is a solid-state, electronically controlled variable resistor that emulates the mechanical wiper action of a traditional potentiometer through an array of fixed resistor segments switched by MOSFET transistors. It sits in the signal-chain hierarchy between analog passives (mechanical pots, trimmers) and active programmable components (DACs, voltage references), offering digital control, non-volatile memory, and small footprint while trading off absolute accuracy and current-handling versus mechanical parts. Digipots are commonly used for calibration, gain control, and bias adjustment in systems where software-driven tuning replaces manual trim. Key features of the MCP4361-503E/ST include a high-resolution 257-tap wiper position per channel, an SPI-compatible serial interface running up to 10 MHz, a hardware RESET input, and WiperLock technology to prevent unauthorized wiper changes. Each channel can be configured as a two-terminal rheostat or three-terminal potentiometer divider, with separate high-side (PxA) and low-side (PxW/PxB) terminal access. Architecturally, the device uses a non-volatile EEPROM cell per wiper so the wiper position is retained across power cycles without software intervention, enabling true plug-and-play calibration in field-deployed equipment. The SPI interface supports both byte and sequential (block/sequential) write/read modes for fast multi-channel updates, and an additional high-voltage (HV) output pin allows direct drive of analog switches in audio or H-bridge systems. Typical applications include LCD display contrast and backlight brightness control, programmable gain amplifiers, sensor calibration and offset trimming, audio volume and tone control, and industrial 4 mA to 20 mA current-loop trims. The wide supply range and industrial temperature grade suit automotive body electronics, programmable logic controllers, and instrumentation front ends. When designing with this part, keep wiper current below 1 mA continuous to avoid non-linear resistance drift and ensure the SPI lines are pulled to defined logic levels during reset. Decouple VDD with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin to suppress digital switching noise on the analog wiper terminals. This page consolidates distributor pricing, drop-in same-brand Microchip alternatives, application notes, and design guidance not found in the standalone manufacturer datasheet.
MCP4362-503E/ST - 50kΩ 8-Bit Quad SPI Digital Potentiometer | Microchip
The Microchip Technology MCP4362-503E/ST is a non-volatile, 8-bit (257 wiper steps) quad-channel digital potentiometer with 50 kΩ end-to-end resistance, SPI-compatible serial interface, and on-chip EEPROM, housed in a 14-pin TSSOP package. According to the manufacturer datasheet, it operates from 2.7 V to 5.5 V single supply, draws 600 nA typical quiescent current, and supports resistance values of 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ across the MCP436X family with identical pinout and command set. A digital potentiometer (digiPot) is a digitally controlled variable resistor implemented as an array of resistor elements with CMOS switches that tap a wiper position under MCU control. In the system hierarchy, the MCP4362 sits under: digital potentiometer -> programmable resistor -> data-acquisition/signal-conditioning IC -> mixed-signal semiconductor. Unlike mechanical potentiometers, digiPots offer logarithmic/scripted adjustment, no PCB moving parts, and non-volatile recall of wiper positions, making them ideal for closed-loop calibration and system-level trimming. Key features include four independent potentiometer channels with separate wiper registers, ±20% end-to-end resistance tolerance, low temperature coefficient of 50 ppm/°C typical, Zero-Crossing detection for clickless audio taper, and a write-lock (WP) pin for EEPROM protection. The device supports SPI modes 0,0 and 1,1 with clock rates up to 25 MHz, allowing fast wiper updates in real-time control loops. Power-on reset restores wiper to mid-scale (0x80) by default. The MCP4362 uses a stacked-resistor ladder architecture with NMOS wiper switches. Each channel has 256 series resistors and 257 tap points, giving 8-bit (256-step) resolution. Non-volatile memory is implemented as EEPROM that automatically reloads wiper settings at power-up, eliminating the need for external configuration storage. Typical applications include LCD backlight brightness control, programmable gain amplifiers, audio volume/gain control, sensor calibration, and programmable voltage references. The TSSOP-14 footprint suits compact designs where four mechanical pots are impractical. When designing with this device, place 0.1 µF decoupling close to VDD and VSS, ensure SPI bus idle-low (mode 0,0) or idle-high (mode 1,1) matches your MCU, and respect the maximum wiper current of 25 mA per tap. For audio applications, select a logarithmic taper configuration or use the Zero-Crossing feature to minimize zipper noise. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet.
MCP45HV51-104E/ST - 100kΩ 8-Bit High-Voltage DigiPot | Microchip
The Microchip Technology MCP45HV51-104E/ST is a single-channel, 8-bit (256-tap) high-voltage digital potentiometer housed in a 14-pin TSSOP package. It provides a nominal end-to-end resistance of 100 kΩ and supports analog signal ranges of 10 V to 36 V single-supply or ±5 V to ±18 V dual-supply, with a maximum wiper current of 6 mA and ±25 mA terminal current. According to the Microchip product page, the device uses an I²C serial interface (up to 3.4 MHz) for tap setting and incorporates non-volatile EEPROM wiper settings plus a wiper-locking mechanism via the WLAT pin. What is a digital potentiometer? A digital potentiometer (digiPot) is an integrated circuit that emulates a mechanical potentiometer or rheostat using an array of resistors switched by MOSFET transistors. The MCP45HV51 belongs to the digital potentiometer category (hypernym hierarchy: digital potentiometer → programmable resistor → variable resistor → passive-adjustable component), but unlike most digiPots that are limited to 5 V signal swings, this "high-voltage" family extends operation into industrial ±18 V and 36 V single-supply rails, making it suitable for replacing mechanical pots in analog signal-conditioning paths. Key features of the MCP45HV51-104E/ST include 8-bit resolution with 256 wiper positions, an I²C interface (with linear-taper log/linear tap codes), non-volatile EEPROM storage of the wiper position, a hardware write-lock (WLAT) pin, and the ability to operate from a single 10 V–36 V rail or split ±5 V to ±18 V rails. Per the manufacturer datasheet, the device draws a typical supply current of approximately 1 mA and supports industrial temperature operation from −40 °C to +125 °C. The internal architecture combines a precision resistor ladder with low on-resistance CMOS switches and a charge-pump-derived bias generator that allows the analog signals on the wiper (W), terminal A, and terminal B to exceed the logic supply rail. This architecture means the part can serve as a true three-terminal potentiometer or as a two-terminal rheostat, with the same internal ESD structures protecting the high-voltage terminals. Typical applications include industrial process-control calibration, programmable-gain instrumentation amplifiers, audio level-set attenuators in professional 24 V systems, programmable voltage references, LCD contrast adjustment, and motor-control bias trim. The high-voltage tolerance makes it particularly well suited to factory automation where analog signal chains operate on ±15 V rails. When designing with the MCP45HV51-104E/ST, derate the maximum terminal current (6 mA wiper, ±25 mA through A or B) according to your power-dissipation budget; for 100 kΩ at the worst-case end-to-end resistance, the wiper voltage should be kept well inside the absolute-maximum analog-signal ratings. The I²C address is factory-set per the part marking and may collide with other I²C devices on the same bus—use the WLAT pin to freeze the wiper during ADC conversions to avoid noise from intermittent switching. This page synthesizes distributor pricing (LCSC $3.0148 as of 2026-10-09, DigiKey and Mouser listings), pin-compatible same-family Microchip alternatives, and PCB design notes not found in the standalone manufacturer datasheet.
MCP6002-E/MC - Dual 1MHz RRIO Op Amp | Microchip
Microchip MCP6002-E/MC is a dual general-purpose operational amplifier with rail-to-rail input and output, a 1.8 V to 6 V operating range, and a typical gain-bandwidth product of 1 MHz. The device is supplied in an 8-lead DFN package measuring 2 x 3 x 0.9 mm with an exposed pad. An operational amplifier, or op amp, is a voltage-gain component used to amplify small signals in analog and mixed-signal systems. The MCP6002 belongs to the broader operational-amplifier, analog-amplifier, semiconductor, and integrated-circuit hierarchies. Its two amplifiers share one package, allowing compact designs that require two independent signal channels, such as sensing, filtering, buffering, or gain stages. The principal features include dual rail-to-rail input and output operation, a low 1.8 V minimum supply for portable and low-power systems, a 6 V maximum supply, 1 MHz typical gain-bandwidth product, and 100 microampere typical quiescent current. The E-grade ordering option is specified for extended-temperature operation, making the MCP6002-E/MC suitable for industrial and instrumented systems requiring operation beyond the standard commercial-temperature range. The rail-to-rail input stage accepts signals extending toward the supply rails, while the rail-to-rail output stage can approach the output limits under suitable load and output-voltage conditions. This combination is useful in battery-powered instrumentation, sensor interfaces, and low-voltage control circuits where signal headroom is limited. The 1 MHz bandwidth favors low-frequency amplification, buffering, filtering, and general-purpose analog functions rather than high-speed signal processing. Typical uses include two-channel sensor conditioning, active filtering, transimpedance stages, audio preamplification, voltage followers, and low-voltage data-acquisition systems. The dual configuration also reduces package count when two amplifiers are required, while the 100 microampere typical quiescent current helps limit standby consumption in battery-operated equipment. Layout and stability remain the main design responsibilities. Place decoupling capacitors close to the supply pins, connect the exposed pad to the appropriate ground plane, and verify gain-bandwidth, output-load, and capacitive-load stability in the final circuit. The application circuit should also account for input and output common-mode limits, output-current capability, noise, and the transition into saturation near the supply rails. This page combines manufacturer specifications, package details, sourcing information, strict drop-in alternatives, application guidance, and practical design notes to support component selection and PCB implementation.
MCP6002-E/MS - Dual 1 MHz Low-Power Op Amp | Microchip
The Microchip Technology MCP6002-E/MS is a dual general-purpose operational amplifier with a typical gain-bandwidth product of 1 MHz, a typical quiescent current of 100 uA, and a 1.8 V to 5.5 V supply range. The device provides rail-to-rail input and output operation and is packaged in an 8-lead MSOP. Its two amplifiers make it suitable for compact dual-channel analog signal-conditioning circuits that require low power and a low operating voltage. An operational amplifier is an active analog component that amplifies the voltage difference between its two inputs while using negative feedback to set the closed-loop gain. The MCP6002 belongs to the general-purpose operational-amplifier hierarchy, combining rail-to-rail signal handling, low quiescent consumption, and moderate bandwidth. This makes it practical for battery-operated instrumentation, low-voltage sensor interfaces, buffer stages, and general analog signal conditioning. Key characteristics include two amplifier channels in one package, a 1 MHz typical gain-bandwidth product, and a 100 uA typical quiescent current. Rail-to-rail inputs allow signals close to either supply rail to be sensed without requiring a separate common-mode reference. Rail-to-rail outputs increase usable output swing, although the datasheet should be consulted for the exact output-voltage limits and load-dependent behavior. The 1.8 V minimum supply supports low-energy systems, while operation up to 5.5 V accommodates common 3.3 V and 5 V rails. The MCP6002 combines two general-purpose amplifiers in one MSOP package, reducing component count and board area compared with separate single-channel devices. Its 1 MHz bandwidth is suitable for moderate-frequency instrumentation rather than high-speed signal paths. The low 100 uA typical quiescent current reduces standby demand in battery-powered designs. Because gain-bandwidth product, noise, slew rate, common-mode range, output swing, and stability behavior determine practical performance, those parameters should be checked against the required signal bandwidth and load before finalizing a design. Typical applications include low-voltage sensor conditioning, dual-channel filtering, microphone or audio preamplification at low frequencies, current-to-voltage conversion, and general-purpose buffering. The dual configuration is especially useful when two related analog signals must be amplified with matching device characteristics. A single package can also simplify layout by placing both channels near one another, although each channel still requires correct bypassing and stable feedback-network placement. For implementation, place the supply bypass capacitor close to the positive and ground pins and route each output to its load with a path that minimizes parasitic capacitance. Do not assume full rail-to-rail output under every load; use the output-voltage limits and capacitive-load stability information in the MCP6002 datasheet. Check input and output common-mode boundaries, maximum differential input voltage, operating temperature, and noise requirements during sign-off. This product page combines the manufacturer specifications with package, pricing-record, replacement, and practical design guidance. It emphasizes the MCP6002-E/MS distinctions that matter when selecting a dual low-power amplifier for low-voltage analog systems, including the 1 MHz bandwidth, 100 uA typical quiescent current, rail-to-rail operation, and 8-lead MSOP implementation.
MCP6002-E/P - Dual 1MHz Low-Power Op Amp | Microchip
Microchip Technology MCP6002-E/P is a dual general-purpose CMOS operational amplifier with rail-to-rail input and output capability, a 1.8 V to 6 V operating supply range, 1 MHz typical gain-bandwidth product, and 100 µA typical quiescent current per amplifier. The device is packaged in an 8-lead PDIP for through-hole PCB assembly. An operational amplifier, or op amp, is an analog signal-conditioning IC that uses high open-loop gain to amplify differences between two input voltages. The MCP6002 belongs to the operational-amplifier hierarchy and is specifically intended for general-purpose voltage amplification, buffering, filtering, and low-frequency signal-processing circuits where low power consumption and rail-to-rail signal handling are valuable. The amplifier's rail-to-rail input stage accepts input voltages across most of the supply range, while its rail-to-rail output stage can approach the positive and negative supply rails under suitable load conditions. This makes the MCP6002 useful in battery-powered equipment, sensor interfaces, and mixed-signal systems operating from 1.8 V to 6 V. Its 1 MHz typical gain-bandwidth product supports modest closed-loop bandwidth requirements rather than high-speed signal processing. Microchip specifies a typical quiescent current of 100 µA and a typical 90° phase margin for the MCP6001, MCP6002, and MCP6004 family. Low quiescent current reduces the standing load imposed by each active channel, which is especially helpful in two-channel designs where both amplifiers may operate continuously. The dual configuration also reduces package count and can simplify board layout compared with two separate single amplifiers. Typical applications include low-frequency sensor conditioning, audio preamplification, voltage buffering, active filtering, joystick or potentiometer interfaces, and portable instrumentation. The 8-lead PDIP package is particularly useful for prototypes, educational equipment, through-hole industrial assemblies, and designs where a socket or hand-soldering is preferred over a fine-pitch surface-mount footprint. Designers should account for input common-mode behavior, output swing, noise, stability with the selected feedback network, and the limits of a 1 MHz amplifier when planning closed-loop gain. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be biased into a valid common-mode range. The DIP outline also requires adequate clearance for through-hole drilling and component spacing. This page combines the manufacturer's device characteristics, documented package choices, equivalent-amplifier guidance, and practical selection criteria. It is intended to help engineers determine whether the MCP6002-E/P's low-power dual-channel architecture and PDIP package fit a specific analog circuit without confusing it with faster, noisier, or more highly integrated alternatives.
MCP6002-I/MS - Dual 1MHz Rail-to-Rail Op Amp | Microchip
The Microchip Technology MCP6002-I/MS is a dual general-purpose operational amplifier with rail-to-rail input and output operation, a 1.8 V to 6 V supply range, and a typical 1 MHz gain-bandwidth product in an 8-lead MSOP package. The two amplifiers are designed for low-voltage, low-power analog signal conditioning. An operational amplifier is an active analog circuit element that uses high-gain differential amplification to process signals between its supply rails. The MCP6002 belongs to the operational-amplifier hierarchy and combines rail-to-rail signal handling with a typical quiescent current of 100 microamperes. These characteristics make the device applicable to battery-powered instruments, sensor interfaces, audio and communication paths, and other systems operating from low-voltage rails. The MCP6002 provides two amplifier channels in one package, reducing board area compared with two separate single amplifiers. Rail-to-rail inputs allow signals to use most of the available supply-voltage range, while rail-to-rail outputs improve output swing. Its 1 MHz typical gain-bandwidth product supports general-purpose amplification, and its 100 microampere typical quiescent current helps limit supply consumption in portable equipment. Both channels share a common supply architecture, making the MCP6002 suitable for matched signal-processing stages such as instrumentation amplifiers, filters, and differential front ends. The operating range of 1.8 V to 6 V covers common low-voltage supply systems. Because the MCP6002 is a general-purpose amplifier rather than a precision or high-speed device, applications requiring very low offset voltage, very high bandwidth, or extended supply voltage should use a more specialized amplifier family. Typical uses include battery-operated sensor acquisition, low-voltage audio signal conditioning, industrial control interfaces, communications equipment, and portable measurement systems. In a current-sense or transducer interface, the amplifier can operate directly from a low-voltage rail while accepting signals near either rail. In an active filter or gain stage, the 1 MHz bandwidth should be checked against the required closed-loop bandwidth and stability margin. PCB implementation should place input and output components close to their associated pins, maintain short feedback paths, and provide adequate ground-plane continuity. Because rail-to-rail operation does not guarantee equally precise behavior throughout the entire input range, designers should evaluate signal levels, common-mode voltage, output load, and required accuracy against the manufacturer's recommended application conditions. This product page consolidates the manufacturer specifications, package information, pricing evidence, available drop-in candidates, and practical design guidance for the MCP6002-I/MS. It supports faster engineering selection by separating known device characteristics from parameters that require confirmation in the manufacturer datasheet.
MCP6002-I/P - Dual 1MHz R-R Op Amp | Microchip Technology
Microchip Technology MCP6002-I/P is a dual general-purpose operational amplifier with rail-to-rail input and output capability, a 1 MHz typical gain-bandwidth product, and 100 uA typical quiescent current. The device operates from 1.8 V to 6 V and is offered in an 8-lead plastic DIP package. An operational amplifier is an analog signal-conditioning semiconductor that compares an input signal with a feedback-defined reference and amplifies the difference. The dual MCP6002-I/P contains two independent amplifiers in one package, placing it in the hierarchy of operational amplifier, analog amplifier, linear amplifier, signal-conditioning IC, and integrated circuit. Rail-to-rail input and output behavior supports signal operation near the supply rails. The principal features are a 1.8 V minimum operating voltage, a 6 V maximum operating voltage, 1 MHz typical gain-bandwidth product, and 100 uA typical quiescent current. Its 90-degree typical phase margin supports stable operation in conventional closed-loop configurations. The dual amplifier arrangement reduces component count when two independent analog channels are required, while the low-power operating characteristics suit battery-powered and portable equipment. Operationally, the MCP6002-I/P uses its two amplifier sections for independent signal conditioning, buffering, amplification, or feedback-control functions. Rail-to-rail input capability expands the usable input range toward the supply limits, while rail-to-rail output capability allows output voltage to approach those limits under suitable load and frequency conditions. The 1 MHz gain-bandwidth product defines the approximate closed-loop bandwidth available at a given noise-gain setting. Typical applications include low-power sensor conditioning, portable instrumentation, audio input stages, general-purpose voltage buffering, and embedded analog signal processing. Two amplifier sections can handle related channels, such as differential sensor excitation and acquisition or separate signal-conditioning paths. The 8-lead DIP package is particularly useful for prototypes, educational systems, through-hole assemblies, and designs where a socketed or manually assembled implementation is preferred. Designers should verify the signal bandwidth, output swing, input bias current, noise, stability, and load-driving requirements against the operating voltage and load. Place bypass capacitors close to the supply pins, route feedback paths away from noisy input and power nodes, and confirm that the selected gain does not compromise phase margin. The DIP footprint also requires adequate spacing around adjacent board components and consideration of lead-bend radius during manual assembly. This product page combines the manufacturer product information, distributor availability references, and engineering cross-reference results into a focused engineering overview. It also provides package-specific guidance, practical application context, design cautions, and a comparison framework for evaluating drop-in amplifier options without changing the 8-lead DIP footprint.
MCP6002-I/SN - Dual 1MHz Op Amp, RRIO, 1.8-6V | Microchip
The Microchip Technology MCP6002-I/SN is a dual, general-purpose operational amplifier offering rail-to-rail input and output (RRIO) operation over a 1.8V to 6.0V supply range. Housed in an 8-pin SOIC (SN) package, it provides a typical gain-bandwidth product (GBWP) of 1 MHz, 90-degree phase margin, and a low typical quiescent current of 100 microamperes per amplifier. Industrial temperature range is -40C to +85C. A rail-to-rail operational amplifier is a type of analog IC whose input common-mode range and output swing extend to both supply rails, enabling full utilization of the ADC dynamic range in low-voltage single-supply systems. The MCP6002 sits within the broader product taxonomy of op amp -> amplifier IC -> analog IC -> integrated circuit -> semiconductor. Compared to non-RRIO op amps that lose 1-2V of headroom at each rail, RRIO architectures are the standard choice for battery-powered, sensor-interface, and mixed-signal designs. Key features include a 1 MHz gain-bandwidth product, 0.6 V/microsecond slew rate, 1 pA typical input bias current, and rail-to-rail input/output that allows zero-crossover distortion-free operation near the rails. The device is unity-gain stable, supports capacitive loads up to 200 pF, and includes ESD protection diodes on the inputs. The 8-pin SOIC (SN) package provides a familiar, easy-to-prototype footprint for through-hole-style adapter boards and reflow soldering. Architecturally, the MCP6002 uses a CMOS input stage that achieves 1 pA input bias current - several orders of magnitude lower than bipolar op amps - while the class AB output stage delivers rail-to-rail swing at moderate loads. The combination of low bias current and RRIO makes the part suitable for high-impedance sensor front-ends, photodiode transimpedance amplifiers, and unity-gain buffers driving single-supply ADCs. Typical applications include battery-powered sensor signal conditioning, active filters for audio and instrumentation, transimpedance amplifiers for photodiodes, microcontroller analog input/output buffering, and general-purpose signal amplification in industrial, consumer, and IoT designs. When designing with the MCP6002, observe the input common-mode range includes both rails, but for best distortion performance keep the input 0.3V away from either rail. Decouple the supply pin with a 0.1 microfarad ceramic capacitor placed within 5 mm of the VDD pin, and avoid exceeding 6.0V absolute maximum supply. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, drop-in SOIC-8 alternatives including same-family Microchip variants and competitor equivalents, and practical design notes not consolidated on any single manufacturer page.