Amplifier ICs
بەرهەمەکان (3,200+)
MCP6004-E/P - 1MHz Quad Low-Power Op Amp | Microchip Technology
The Microchip Technology MCP6004-E/P is a quad general-purpose operational amplifier with rail-to-rail input and output capability, a typical 1 MHz gain-bandwidth product, and a typical 100 uA quiescent current. It operates across a 1.8 V to 6 V supply range and is supplied in a 14-pin PDIP package. The -E/P temperature grade supports an operating range of -40C to +125C. An operational amplifier is an analog signal-conditioning device that compares an input voltage with a feedback reference and amplifies the difference. The MCP6004 contains four amplifiers in one package, allowing a compact circuit to perform buffering, amplification, filtering, sensing, and feedback-control functions. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation helps preserve dynamic range in low-voltage systems. The 1 MHz typical gain-bandwidth product supports general-purpose signal paths rather than high-speed precision applications. The low 100 uA typical quiescent current is useful in battery-operated and portable equipment where standby current affects battery life. The 14-pin PDIP package is also practical for through-hole prototyping, educational platforms, and industrial assemblies where a socket or through-hole layout is preferred. The amplifier family is designed around low-power operation and broad supply compatibility. MCP6004-E/P provides four channels in a single package, reducing the number of components required for multi-channel analog front ends. Its 60 dB minimum common-mode rejection ratio and 4.5 mV input-offset-voltage figure provide useful guidance when designing precision sensor interfaces, although application-level error budgets must account for input bias current, resistor tolerances, noise, and temperature effects. Typical applications include battery-powered sensor conditioning, portable instrumentation, low-voltage audio signal paths, industrial control modules, and general-purpose analog boards. When designing with this device, keep input and feedback networks within the amplifier's common-mode and output-range limits, check stability with the selected load and capacitance, and provide adequate supply bypassing close to the power pins. This product page combines the manufacturer's device information, distributor listings, pin and package references, and engineering-focused design guidance. It helps engineers evaluate the MCP6004-E/P for low-voltage, low-power analog designs before selecting a qualified replacement or planning a new PCB layout.
MCP6004-E/SL - Quad 1MHz R-R Op Amp | Microchip
The Microchip Technology MCP6004-E/SL is a quad general-purpose operational amplifier with rail-to-rail input and rail-to-rail output, a 1.8 V to 6 V operating supply range, and a typical gain-bandwidth product of 1 MHz. It is packaged in a 14-lead SOIC. The MCP6004 family is designed for low-power signal conditioning where four independent amplifiers and broad supply-voltage compatibility simplify PCB planning. An operational amplifier is an active semiconductor component that compares an input signal with a feedback network and amplifies the resulting error. Rail-to-rail input and output operation allows the amplifier to approach the supply rails during signal processing, while a 1.8 V to 6 V supply range supports low-voltage sensor, portable-instrumentation, industrial-control, and embedded-system designs. Within the broader power-management and signal-chain hierarchy, the MCP6004 is a voltage-feedback operational amplifier intended for general-purpose analog conditioning. Each amplifier channel combines a typical 1 MHz gain-bandwidth product with low-power operation and a typical quiescent current of 100 µA. The four-channel integration reduces package count and allows one device to provide filtering, amplification, buffering, or level conversion in a multi-channel analog circuit. Rail-to-rail input and output capability is particularly useful when signals occupy much of the available supply range or when the circuit must process low-amplitude sensor outputs. The MCP6004-E/SL is the standard-grade E-temperature variant and is identified as a four-circuit, 14-SOIC amplifier. Typical applications include current sensing, sensor interfaces, battery-powered equipment, audio preamplification, data acquisition, and general-purpose analog signal conditioning. Its 1 MHz bandwidth is appropriate for moderate-frequency measurement and control loops rather than high-speed video or precision instrumentation requiring substantially greater bandwidth. PCB design should preserve the exposed copper and pin clearance required by the 14-lead SOIC footprint and account for input-bias-current and output-swing limitations when operating near the supply rails. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs should be routed away from switching nodes. Feedback components should be selected with tolerances appropriate to the gain accuracy required by the application. This page consolidates the exact MCP6004-E/SL electrical characteristics, package information, sourcing path, compatible alternatives, and practical PCB guidance into a concise engineering reference. It also identifies which electrical and environmental details should be confirmed in the Microchip manufacturer datasheet before a production design is released.
MCP6004-E/ST - 1MHz Quad RRIO Op Amp | Microchip
The Microchip Technology MCP6004-E/ST is a quad, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 100 uA typical quiescent current, and rail-to-rail input and output operation in a 14-lead TSSOP package. It operates from 1.8 V to 5.5 V, making it suitable for low-voltage sensor, signal-conditioning, and mixed-signal systems. An operational amplifier is an analog building block that amplifies the difference between two input voltages. In the broader semiconductor hierarchy, the MCP6004-E/ST is an operational amplifier, analog amplifier, and linear semiconductor. Its rail-to-rail inputs accept signals extending close to the positive and negative supply rails, while rail-to-rail outputs can swing close to those limits under suitable load conditions. Key features include a 1 MHz gain-bandwidth product, 100 uA typical quiescent current, and operation across a 1.8 V to 5.5 V supply range. The device provides four amplifier channels in one package, reducing component count and board area for quad-signal paths. Its low-noise characteristics and 76 dB ESD protection make it appropriate for general-purpose analog front ends. The MCP6004 family uses a low-power CMOS operational-amplifier architecture optimized for portable and embedded equipment. A 1 MHz bandwidth supports low-frequency signal amplification, filtering, buffering, and feedback control. The quad configuration allows four independent channels to share the same supply pins, simplifying power distribution while preserving channel-to-channel functional separation. Typical applications include battery-powered sensor interfaces, buffered ADC inputs, current sensing, portable instrumentation, audio preamplification, and general feedback loops. The 1.8 V minimum supply voltage is especially useful for energy-harvesting, edge-sensing, and embedded systems operating from low-capacity batteries. When designing around the MCP6004-E/ST, place each bypass capacitor close to the supply pins and route sensitive input traces away from switching nodes. Because the device is intended for general-purpose and low-frequency work, verify closed-loop stability, capacitive loading, output swing, and noise performance before using it in precision or high-bandwidth instrumentation. This page combines the manufacturer specifications with package details, application guidance, and same-package amplifier comparisons. It helps engineers distinguish the standard MCP6004-E/ST from industrial-temperature, tape-ordering, and related amplifier variants before committing a 14-TSSOP design to production.
MCP6004-I/P - Quad 1MHz Low-Power Op Amp | Microchip
The Microchip Technology MCP6004-I/P is a quad general-purpose operational amplifier with rail-to-rail input and rail-to-rail output operation, a 1.8 V to 6 V supply range, a typical gain-bandwidth product of 1 MHz, and a typical quiescent current of 100 µA per amplifier. The device is supplied in a 14-lead PDIP package. An operational amplifier, or op amp, is a high-gain analog signal-processing component that compares two input voltages and amplifies the difference between them. Within the power-management and signal-conditioning hierarchy, the MCP6004 belongs to the general-purpose amplifier class, combining four independent amplifier channels in one integrated circuit. Rail-to-rail input and output capability lets each channel operate close to the supply rails, which is useful in low-voltage systems where the available signal range is limited. Key features include four amplifier channels, a 1.8 V minimum operating supply, a 6 V maximum operating supply, 1 MHz typical gain-bandwidth product, and 100 µA typical quiescent current. The MCP6004-I/P also provides rail-to-rail input and output behavior. These characteristics make it suitable for low-power sensor conditioning, buffering, general analog signal processing, and mixed-signal systems that require multiple amplifier functions without using four separate packages. The 1 MHz gain-bandwidth product supports operation from low-frequency signal conditioning through moderate-bandwidth applications. At unity gain, the usable bandwidth is approximately 1 MHz under typical conditions. Rail-to-rail input capability supports sensing signals near the positive or negative supply limit, while rail-to-rail output allows the amplifier to produce output voltages close to either rail. Actual output swing and stability still depend on load, supply voltage, frequency, and the surrounding circuit. Typical uses include sensor signal conditioning, low-frequency active filtering, voltage buffering, transimpedance stages, instrumentation interfaces, and general-purpose analog gain stages. The four integrated channels can also implement functions such as dual differential amplifiers, comparators with suitable feedback arrangements, or multiple single-ended amplifier stages. Because the MCP6004-I/P operates from 1.8 V to 6 V, it is especially relevant to portable, embedded, industrial-control, and low-voltage instrumentation designs. Designers should verify the required output-current capability, operating temperature grade, noise, offset voltage, and stability under the intended load before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be kept away from fast-switching nodes. The 14-lead PDIP package also requires adequate spacing between adjacent board-level circuits because its through-hole leads are larger than those of surface-mount packages. This product record combines verified manufacturer and distributor information, exact package identification, purchasing data, application guidance, and an honest review of available drop-in alternatives. It also highlights where additional verification is needed, including the complete pin mapping and alternative qualification, rather than presenting unsupported assumptions as confirmed specifications.
MCP6004-I/SL - Quad 1MHz R-R Op Amp | Microchip Technology
The Microchip Technology MCP6004-I/SL is a quad general-purpose operational amplifier with rail-to-rail input and output, a 1.8 V to 6 V operating range, a typical 1 MHz gain-bandwidth product, and a typical 100 µA quiescent current. The device is supplied in a 14-lead SOIC package designated by the SL suffix. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The MCP6004 belongs to the operational-amplifier hierarchy, where it sits below the general-purpose amplifier category and above the CMOS low-power amplifier class. Four amplifiers in one package make it useful for multi-channel analog systems where several low-frequency signals must be amplified, buffered, or filtered. Rail-to-rail input allows the MCP6004 to accept signals close to either supply rail, while rail-to-rail output improves output-voltage range at light load. Its typical 1 MHz gain-bandwidth product supports general-purpose low-frequency signal paths. The typical 100 µA quiescent current also makes the device suitable for portable, battery-powered, and low-power sensor equipment when operating speed is not the primary requirement. The MCP6004 family uses a CMOS-based operational-amplifier architecture optimized for low power and low cost. With four rail-to-rail amplifiers in one 14-lead SOIC, it reduces component count in designs requiring multiple channels. The operating voltage range of 1.8 V to 6 V supports systems built around low-voltage rails, although the selected amplifier must also satisfy required output swing, input common-mode range, noise, stability, and precision requirements. Typical uses include sensor-signal conditioning, low-voltage data acquisition, audio input stages, general buffering, and four-channel filtering. In a sensor interface, the amplifier can increase the usable level of a low-amplitude transducer signal before conversion or control. In portable instrumentation, low quiescent current helps preserve battery life, while the four-channel package reduces board area. Circuit design should account for the amplifier's gain-bandwidth limit and the stability requirements of the feedback network. Place input and output components close to the device, maintain the recommended bypass capacitance, and verify that source impedance, load capacitance, and noise gain do not compromise stability. The manufacturer datasheet should be used for the complete pin-description table and application limits. This product page combines the manufacturer's operating-range and performance information with package details, practical application guidance, and verified drop-in replacement options. It also provides pin-focused search coverage and comparison parameters that help engineers evaluate the MCP6004-I/SL for low-voltage, low-power analog designs.
MCP6007-E/MS - Dual 1MHz R-R Op Amp | Microchip
The Microchip Technology MCP6007-E/MS is a dual general-purpose operational amplifier with a typical gain-bandwidth product of 1 MHz, rail-to-rail input and output operation, and an 8-MSOP package. It supports single-supply operation from 1.8 V to 5.5 V and consumes no more than 70 µA per amplifier. The MCP6007-E/MS is unity-gain stable and includes EMI filtering for applications where sensitive analog signals must remain usable near digital circuitry. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare two input voltages. The MCP6007 family belongs to the operational-amplifier hierarchy within analog and linear semiconductors, where rail-to-rail input and output capability lets the amplifier operate across most or all of the supply voltage. The dual configuration provides two amplifiers in one package, reducing component count in filter, buffer, instrumentation, and sensor-conditioning circuits. The two amplifiers provide a typical 1 MHz gain-bandwidth product, low input bias current, and rail-to-rail input and output behavior. Maximum input offset voltage is ±1.6 mV per amplifier, while maximum quiescent current is 70 µA per amplifier. These characteristics make the device suitable for low-power battery instrumentation, portable measurement systems, sensor interfaces, and general analog signal-conditioning applications operating near the lower end of its supply range. The MCP6007-E/MS is unity-gain stable, allowing direct use as a voltage follower without imposing a minimum closed-loop gain. Its low-frequency bandwidth favors precision measurement, filtering, buffering, and amplification rather than wideband signal processing. EMI filtering improves behavior in systems containing switching nodes or fast digital transitions, although layout, bypassing, and source-impedance considerations remain necessary for predictable low-noise performance. Typical uses include battery-powered sensor conditioning, buffered transducer inputs, active low-pass filters, low-voltage analog signal chains, general-purpose dual filters, and portable test equipment. The dual package works well when two related channels are required, such as differential sensing or paired filtering stages, because both amplifiers share the same package and supply architecture. For stable operation, place input and output bypass capacitors close to their respective pins, keep sensitive input traces away from switching-current paths, and confirm that the selected gain, output load, and common-mode input range suit the intended supply voltage. The MSOP package also requires careful thermal and solder-joint inspection where repeated temperature cycling or mechanical stress is expected. This page organizes the manufacturer's principal operating specifications, sourcing details, application guidance, and verified drop-in comparison information. The engineering sections also highlight package, supply-voltage, offset, bandwidth, and quiescent-current considerations that must be checked together before the amplifier is approved for a new analog design.
MCP6007-E/SN - Dual 1MHz RRIO Op Amp | Microchip
The Microchip Technology MCP6007-E/SN is a dual, general-purpose operational amplifier featuring a 1 MHz typical gain-bandwidth product, 1.9 V/µs typical slew rate, and rail-to-rail input and output operation in an 8-pin SOIC package. It operates from single supplies as low as 1.8 V, while the E-grade suffix identifies operation from -40°C to +125°C. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential feedback to amplify, buffer, filter, or isolate signals. The MCP6007 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Rail-to-rail input operation permits signals to approach the supply limits, while rail-to-rail output improves output swing and makes the device useful in compact, low-voltage sensor and signal-processing systems. The MCP6007 combines a 1 MHz typical gain-bandwidth product with rail-to-rail input and output capability. Maximum input offset voltage is ±1.6 mV, and maximum quiescent current is 70 µA per amplifier. The device is unity-gain stable and includes EMI filtering, making it suitable for direct sensor conditioning, low-frequency active filtering, voltage buffering, and general-purpose analog signal chains operating from low-voltage supply rails. Its two amplifiers share the same supply pins but provide independent input and output pins, allowing simultaneous dual-channel signal processing. The 1.9 V/µs typical slew rate supports reasonably clean transitions in low-bandwidth applications. A 1 MHz gain-bandwidth product is more appropriate for precision, low-speed analog functions than for high-speed video, RF, or wideband pulse applications, while the low 70 µA maximum quiescent current per amplifier favors battery-operated equipment. Typical uses include bridge-amplifier signal conditioning for resistive sensors, active low-pass filters, audio input buffers, portable instrumentation, and low-current sensor interfaces. Because the MCP6007 supports rail-to-rail input and output, it is particularly useful when the signal span is close to the available supply voltage. Supply bypass capacitors close to the power pins remain essential for stable operation in practical layouts. The primary design trade-off is bandwidth: the 1 MHz gain-bandwidth product limits large-signal response and closed-loop performance at higher frequencies. Designers should also check noise, output-current capability, and stability with the selected feedback network for each gain setting. The E-grade temperature range supports industrial environments, but the SOIC-8 package is larger than modern leadless alternatives. This page combines the manufacturer’s electrical characteristics with package, sourcing, comparison, and design guidance for engineers evaluating the MCP6007-E/SN in low-voltage dual-amplifier circuits. It also identifies pin-compatible family alternatives and highlights the measured differences that matter when reusing an existing 8-pin SOIC layout.
MCP6009-E/SL - 4-Channel 1MHz RRIO Op Amp | Microchip
The Microchip Technology MCP6009-E/SL is a four-channel, rail-to-rail input and output operational amplifier featuring a typical gain-bandwidth product of 1 MHz, a 1.8 V to 5.5 V supply range, and a 14-pin SOIC package. It also provides integrated EMI filtering and RF suppression rated at 90 dB, making it suitable for low-power analog signal chains requiring low offset and low input bias current. An operational amplifier, commonly called an op amp, is an active semiconductor that amplifies the difference between two input voltages. In the broader hierarchy, an op amp belongs to the amplifier IC category and the analog signal-processing family. Rail-to-rail input operation permits the input common-mode range to approach the supply rails, while rail-to-rail output operation allows the output voltage to swing close to those limits under suitable load conditions. The MCP6009-E/SL combines four amplifiers in one package. According to the manufacturer datasheet, its typical gain-bandwidth product is 1 MHz, maximum input offset voltage is 1.6 mV, and typical input bias current is 1 pA. Maximum quiescent current is 70 µA per amplifier, while the listed input noise density is 25 nV/√Hz at 1 kHz. The device is unity-gain stable and supports a slew rate of 3 V/µs. Its low-voltage operation is suitable for battery-powered and energy-conscious equipment. The input stage includes capacitive filtering for EMI suppression, reducing sensitivity to interference coupled onto sensitive sensor or measurement lines. Four channels in one SOIC-14 package can also reduce board area when a design needs multiple buffers, amplifiers, or active filters. The family is intended for general-purpose analog signal conditioning rather than precision instrumentation amplification. Typical uses include low-voltage sensor conditioning, portable measurement equipment, audio preamplification, battery monitoring, and general-purpose signal buffering. The MCP6009-E/SL is particularly useful where several low-power channels must operate from the same supply while accepting input signals near either supply rail. Its 1 MHz bandwidth is adequate for low-frequency control, sensing, and audio tasks rather than high-speed video or communications. When designing around the MCP6009-E/SL, keep each input and output connection short, provide a stable supply reference, and avoid capacitive loading on the output. Decoupling capacitors should connect directly between the supply and ground pins near the device. Verify the external feedback network, output load, and input common-mode range across temperature before using the amplifier at the extremes of its 1.8 V to 5.5 V operating range. This product page organizes the amplifier's electrical limits, package information, drop-in alternatives, application guidance, and design considerations into a single engineering reference. It highlights where the 1 MHz bandwidth, low quiescent current, rail-to-rail operation, and EMI filtering make the MCP6009-E/SL useful, while also separating it from options that offer higher speed or different channel counts.
MCP6009-E/ST - 1 MHz Low-Power Quad Op Amp | Microchip
The Microchip Technology MCP6009-E/ST is a general-purpose, quad operational amplifier with a 1 MHz typical gain-bandwidth product, rail-to-rail input and output operation, and a 1.8 V to 5.5 V single-supply operating range. The device is packaged in a 14-pin TSSOP and provides four amplifiers in one package, making it suitable for compact analog signal-conditioning and measurement systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Within the power-management and signal-processing hierarchy, this quad low-voltage operational amplifier belongs to the general-purpose amplifier family. Rail-to-rail input operation allows the input common-mode voltage to extend close to the supply rails, while rail-to-rail output operation improves output-voltage range. The MCP6009 family is unity-gain stable, supporting use as a voltage follower as well as in closed-loop amplifier configurations. The MCP6009-E/ST features low input bias current, an input offset voltage of 1.6 mV maximum, 22 nV/√Hz input-voltage noise at 10 kHz, and 76 dB of EMI filtering and RF suppression. Its typical gain-bandwidth product is 1 MHz, while the listed slew rate is 1.9 V/µs. Each amplifier draws approximately 50 µA of supply current, and the complete 14-pin device is specified for operation from -40°C to +125°C. The low-noise, low-power design combines analog signal conditioning with integrated EMI filtering. This makes the amplifier useful when low-level sensor signals must be amplified near noisy digital, switching, or RF-producing circuitry. A 1 MHz gain-bandwidth product is suitable for low-frequency instrumentation, buffering, and general signal-processing tasks, but it is not intended for high-speed video, high-resolution data acquisition above its bandwidth limits, or demanding precision applications where lower offset and noise are required. Typical applications include battery-powered sensor interfaces, industrial measurement modules, portable medical equipment, audio preamplification, transducer conditioning, and low-voltage control systems. The quad configuration reduces board area by placing four amplifiers in one 14-pin TSSOP. Each amplifier can implement filtering, gain, summing, differential sensing, active filtering, or voltage-following functions, provided the selected gain and phase margin are compatible with the 1 MHz bandwidth. Designers should place input and output decoupling capacitors close to the supply pins, route sensitive input traces away from switching nodes, and verify common-mode, output-swing, stability, and noise performance across the complete operating range. The EMI-filtering characteristic helps reduce high-frequency interference, but it does not remove the need for sound grounding and layout practices. Confirm the exact pin functions and exposed package details against the Microchip MCP6006/6R/6U/7/9 data sheet before laying out a PCB. This product page combines the manufacturer specification summary, package and lifecycle information, engineering application guidance, structured comparison fields, and verified drop-in replacement research. The alternatives section includes only candidates for which a same-package relationship can be substantiated, avoiding cross-package substitutions that would require PCB changes.
MCP601-E/P - 2.8 MHz CMOS Op Amp | Microchip
The Microchip Technology MCP601-E/P is a single, general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, and 1 pA typical input bias current, supplied in an 8-pin PDIP package. It operates from 2.7 V to 6 V and is specified from -40°C to 125°C, combining low power, rail-to-rail output swing, and low offset voltage. An operational amplifier, or op amp, is an active analog component that compares two input voltages and drives its output toward the higher input. Within the power-management and signal-conditioning hierarchy, an op amp provides gain, buffering, filtering, level shifting, or feedback control. The MCP601-E/P is specifically a single-channel CMOS device intended for low-power precision and general-purpose signal conditioning. The MCP601 family's key specifications include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, approximately 230 µA typical operating current, and less than 2 mV offset voltage according to the Microchip product page. Its CMOS process supports low bias current, while the rail-to-rail output stage allows the output to approach the supply rails more closely than a conventional output stage. Because the MCP601 is a general-purpose amplifier rather than a power semiconductor, its performance depends mainly on supply voltage, feedback topology, load, output frequency, and circuit stability. The 2.8 MHz bandwidth supports low-frequency instrumentation and signal conditioning, while the 2.3 V/µs slew rate limits large-signal response. Designers should verify noise, offset, bias current, common-mode range, and output-current limits against the manufacturer datasheet for the exact operating conditions. Typical uses include industrial process-control signal conditioning, low-power battery-operated equipment, portable instrumentation, data acquisition, test equipment, and low-end audio circuits. The DIP package is useful for prototyping and through-hole assemblies where a socketed amplifier or easy component replacement is desired. For new production designs, confirm package availability, temperature grade, supply limits, and lifecycle status directly with Microchip or an authorized distributor. The verified product page identifies MCP601 availability across PDIP, SOIC, TSSOP, and SOT-23A packages, but the exact -E/P order code and commercial terms should be checked for the current design. This page combines verified manufacturer specifications, distributor availability information, package details, and application guidance to support faster component selection for low-power analog signal-conditioning designs.
MCP601-E/SN - 2.8 MHz Low-Power RRIO Op Amp | Microchip Technology
The Microchip Technology MCP601-E/SN is a single operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, and a maximum input offset voltage below 2 mV, supplied in an 8-lead SOIC package. It is designed for low-power analog signal conditioning using a 2.7 V to 6.0 V single supply. An operational amplifier, or op amp, is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. The MCP601 belongs to the CMOS operational amplifier hierarchy: op amp -> voltage-feedback amplifier -> analog signal-conditioning IC -> semiconductor. Its rail-to-rail output swing allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage, which is useful in portable and low-voltage systems. Key features of the MCP601 family include low bias current, high open-loop gain, low typical operating current of 230 uA, and a rail-to-rail output swing. The single MCP601 configuration simplifies designs that require one amplifier, while the 8-lead SOIC package supports conventional surface-mount assembly. The manufacturer identifies the device as suitable for industrial process control, low-power battery-operated equipment, portable equipment, data acquisition, test equipment, and low-end audio applications. The MCP601 uses advanced CMOS technology to provide low bias current and high-speed operation while maintaining low power consumption. Its 2.8 MHz typical gain-bandwidth product supports general-purpose signal amplification rather than high-speed precision applications. The manufacturer datasheet states that the MCP601 operates from a 2.7 V to 6.0 V single supply, although the exact operating temperature and electrical limits for the MCP601-E/SN ordering code should be confirmed against the ordering information in the datasheet. A typical design places input, feedback, and biasing networks around the amplifier, with suitable bypassing close to the supply pins. In battery-powered instrumentation, the 230 uA typical operating current is a meaningful advantage, but the final power budget must include the input bias current, feedback network consumption, and load current. In audio or sensor-signal paths, rail-to-rail output swing can improve available output range, while input common-mode limits and offset voltage remain important selection criteria. The principal design trade-off is bandwidth versus power and precision. A 2.8 MHz amplifier is appropriate for slow analog signals and general-purpose buffering, but it is not the correct choice for wideband video, high-speed instrumentation, or demanding precision applications. Decoupling, layout, input protection, and output-load stability should be reviewed against the manufacturer datasheet before production release. This product summary consolidates the verified manufacturer specifications, distributor availability information, package details, practical application guidance, and explicitly identified drop-in alternatives for engineers evaluating the MCP601-E/SN.
MCP601-E/ST - 2.8MHz RRO Op Amp | Microchip Technology
The Microchip Technology MCP601-E/ST is a single-circuit CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, a 2.3 V/µs slew rate, and rail-to-rail output swing in an 8-TSSOP package. It operates from a 2.7 V to 6 V supply and draws a typical operating current of 230 µA. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, compare voltages, and implement active analog filters. The MCP601 belongs to the CMOS operational-amplifier family and the broader voltage-amplifier and analog-signal-processing hierarchy. Its rail-to-rail output capability increases the usable output range in low-voltage circuits where conventional fixed-output amplifiers would clip near either supply rail. Key features include a 2.8 MHz gain-bandwidth product, 2.3 V/µs slew rate, typical operating current of 230 µA, and typical offset voltage below 2 mV. The low bias current and high open-loop gain provided by Microchip's advanced CMOS process are useful for battery-powered instrumentation, data-acquisition channels, and sensor interfaces. A single amplifier in the TSSOP package also supports compact analog boards requiring a conventional surface-mount footprint. Technically, the MCP601 combines a low-power CMOS core with general-purpose voltage feedback. Its 2.8 MHz gain-bandwidth product supports operation from low closed-loop gains such as 10 through signal chains requiring moderate bandwidth. The 2.3 V/µs slew rate helps the amplifier reproduce moderate-amplitude step inputs, while the rail-to-rail output reduces headroom loss near the positive or negative supply limit. Exact input common-mode range, noise density, and maximum output swing must be confirmed in the manufacturer datasheet. Typical applications include industrial process-control inputs, portable battery-operated equipment, portable data-acquisition systems, test equipment, and low-end audio products. It is particularly appropriate where low operating current, a small package, and output swing close to the supply rails are more important than the bandwidth and noise of a precision or high-speed amplifier. Designers should verify input common-mode limits, output-load capability, noise, and stability for the intended gain and capacitive load using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while sensitive-input routing should minimize parasitic capacitance and leakage. Because rail-to-rail output does not necessarily guarantee a fully rail-to-rail input range, input-source and input-biasing conditions require separate verification. This page consolidates verified manufacturer and distributor information, package-level alternatives, parameter comparisons, and application guidance. It adds engineering-focused selection criteria and implementation notes that help distinguish a low-power TSSOP operational amplifier from higher-bandwidth, precision, and rail-to-rail-input alternatives.
MCP601-I/P - 2.8MHz Low-Power RRIO Op Amp | Microchip
The Microchip Technology MCP601-I/P is a single low-power CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical quiescent current, and rail-to-rail output swing in an 8-pin PDIP package. According to the manufacturer product page, it operates from a single supply as low as 2.7 V, supports a maximum supply voltage of 5.5 V, and provides less than 2 mV typical offset voltage. An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while providing high open-loop gain and low output impedance. The MCP601 belongs to the CMOS operational-amplifier hierarchy, combining low bias current, high speed, high open-loop gain, and rail-to-rail output swing in a general-purpose device intended for industrial process control and low-power portable systems. Key characteristics include a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, rail-to-rail output capability, and low input bias current enabled by Microchip's advanced CMOS process. The single-supply operating range of 2.7 V to 5.5 V makes the device suitable for battery-operated equipment, portable instrumentation, and low-voltage industrial control systems. The -I temperature grade identifies the industrial-temperature version. The rail-to-rail output stage allows the output to approach the supply rails under light load, which is useful in single-supply systems where conventional bipolar output stages lose linearity near either rail. Input common-mode range, input offset voltage, slew rate, open-loop gain, input bias current, and noise specifications must be checked against the manufacturer datasheet for the exact operating voltage and configuration. Typical uses include low-power sensor conditioning, process-control loops, data-acquisition front ends, portable test equipment, and low-end audio signal paths. Its 8-pin PDIP format is also convenient for prototyping, educational builds, and through-hole assemblies where a surface-mount package would be inconvenient. Designers should verify stability with the selected feedback network, account for capacitive loading, and provide adequate bypass capacitance near the supply pins. Because the MCP601-I/P is a through-hole industrial-grade variant, engineers changing to a surface-mount production version should confirm pin order, temperature grade, and full electrical equivalence rather than assuming only the family name is equivalent. This page combines manufacturer specifications, distributor sourcing information, package details, application guidance, and honest drop-in replacement analysis that are not consolidated in a single manufacturer product-page summary.
MCP601-I/SN - 2.8 MHz Low-Power Op Amp | Microchip
The Microchip Technology MCP601-I/SN is a single low-power CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. It operates from a single 2.7 V to 5.5 V supply and provides rail-to-rail output swing in an 8-pin SOIC package. The combination of low power, rail-to-rail output, low bias current, and moderate bandwidth makes the MCP601 suitable for portable instrumentation, process-control circuits, sensor interfaces, buffering, and low-end audio systems. An operational amplifier is a voltage-controlled differential amplifier used to amplify, filter, buffer, or compare analog signals. In the signal-chain hierarchy, the MCP601 belongs to the operational-amplifier family, which falls within analog amplifier ICs and broader analog signal-processing systems. Its CMOS implementation supports low input bias current and low static power while maintaining high open-loop gain and rail-to-rail output capability. Key electrical characteristics include a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, an offset voltage below 2 mV, and a 2.7 V to 5.5 V single-supply range. Rail-to-rail output swing allows the amplifier to approach the supply rails under suitable load and output-voltage conditions. The 8-pin SOIC package supports conventional surface-mount assembly and provides separate positive-input, negative-input, output, supply, and ground connections. The advanced CMOS process combines low power consumption with high-speed operation and high open-loop gain. Low input bias current is especially useful when the amplifier is driven by high-impedance sensors or bias networks because it reduces loading-induced errors. The 2.8 MHz gain-bandwidth product is appropriate for general-purpose signal conditioning, audio preamplification, active filtering, and instrumentation rather than high-speed precision applications requiring much wider closed-loop bandwidth. Typical uses include portable sensor interfaces, industrial process-control modules, low-power battery-operated equipment, data-acquisition systems, test equipment, and low-end audio circuits. In a sensor interface, the MCP601 can buffer a high-impedance source before conversion by an ADC. In an active filter, its bandwidth provides useful operating range at moderate signal frequencies. In audio equipment, rail-to-rail output can improve available output swing compared with a fixed-headroom implementation. Design the input network and output load carefully because rail-to-rail output behavior does not eliminate all input common-mode limitations or guarantee maximum swing into every load. Confirm settling time, output-current capability, noise, and stability against the required signal bandwidth. Place the device close to its bypass capacitors and route supply and ground returns to minimize high-frequency impedance and unwanted coupling. This page combines the MCP601-I/SN electrical specifications, manufacturer documentation, application guidance, and verified drop-in replacement information to support faster component selection and PCB-level design decisions.
MCP601-I/ST - 2.7V Rail-to-Rail CMOS Op Amp | Microchip
The Microchip Technology MCP601-I/ST is a single-circuit general-purpose CMOS operational amplifier with rail-to-rail output swing, a 2.7 V minimum supply, and an 8-lead TSSOP package. It operates from a 2.7 V to 5.5 V single supply, making it appropriate for compact, low-voltage analog signal chains. The MCP601-I/ST variant uses the extended industrial temperature grade indicated by its part numbering. A CMOS operational amplifier is an analog building block that uses high input impedance and voltage gain to amplify small signal differences. The MCP601 belongs to the operational-amplifier hierarchy, which connects to analog signal-processing ICs and broader semiconductor systems. Its CMOS construction is intended to support low power consumption, low input bias current, and operation from low-voltage supplies while preserving useful open-loop gain. The manufacturer identifies the MCP601 family as a low-power operational amplifier with rail-to-rail output swing. This output capability is useful when the usable output range must extend close to either supply rail. The family also supports operation with supply voltages as low as 2.7 V and draws less than 325 uA of quiescent current according to the Microchip product page. These characteristics make it useful in battery-operated and portable equipment where every milliamp of supply demand can affect runtime. The MCP601-I/ST uses Microchip's advanced CMOS process technology. Publicly indexed product information describes low bias current, high-speed operation, and high open-loop gain. These properties support sensor conditioning, buffering, and low-level signal amplification, although exact gain-bandwidth, slew-rate, input-bias-current, and offset figures are not included in the supplied verified records and therefore remain marked for data retrieval. Typical uses include portable sensor interfaces, low-voltage instrumentation, audio signal conditioning, and general-purpose analog buffers. In a sensor interface, the amplifier can sit between a high-impedance transducer and a downstream ADC. In a battery-powered circuit, its sub-325 uA quiescent current and 2.7 V minimum operating supply help conserve available energy. Its rail-to-rail output reduces the headroom required when driving a following stage. Designers should verify the complete electrical limits and stability requirements against the manufacturer datasheet before production use. Decoupling capacitors, source impedance, output loading, and the selected gain can affect practical performance. The 8-pin TSSOP footprint is compact, but the exposed thermal limitations and assembly requirements of this small package should be considered alongside ambient temperature and expected dissipation. This page consolidates the verified distributor listing, manufacturer family information, package identification, current pricing reference, and practical selection context. It also distinguishes confirmed drop-in options from package variants that require PCB consideration, helping engineers compare replacements without treating electrically similar parts as automatically interchangeable.
MCP601T-E/SN - 2.8MHz R-R Op Amp | Microchip Technology
The Microchip Technology MCP601T-E/SN is a single-circuit, general-purpose CMOS operational amplifier featuring a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, an offset voltage below 2 mV, and rail-to-rail output swing in an 8-pin SOIC package. It operates from single supplies rated from 2.7 V to 5.5 V and includes a common-mode input range that extends below ground. An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to set its closed-loop behavior. The MCP601 belongs to the broader hierarchy of analog amplifiers, amplifier ICs, and semiconductor signal-conditioning devices. Its CMOS implementation emphasizes low bias current, low operating current, high open-loop gain, and rail-to-rail output capability, making it suitable for portable and low-voltage signal-processing systems. Three defining characteristics are its 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. Rail-to-rail output swing allows the output voltage to approach the supply rails under suitable load conditions. Common-mode input operation below ground is valuable in single-supply circuits that process small signals centered around ground. Unity-gain stability supports direct use as a voltage follower when configured with its output connected to its inverting input. The MCP601 uses Microchip’s advanced CMOS technology. This architecture provides low bias current, which is important when the amplifier must sense signals from high-impedance sources without loading them aggressively. Its 2.8 MHz gain-bandwidth product provides more bandwidth than many low-power general-purpose amplifiers, while the 230 uA typical operating current supports designs where supply consumption is an important constraint. Rail-to-rail output swing improves usable output range on low-voltage rails. Typical applications include sensor-signal conditioning, portable instrumentation, battery-powered measurement systems, audio preamplification, and low-voltage analog signal chains. The device is also useful as a buffer or active filter when the selected feedback network keeps the closed-loop gain and bandwidth within stable operating limits. Because its input range can extend below ground, it can simplify signal conditioning around a zero-volt reference. When designing around the MCP601T-E/SN, use the manufacturer’s recommended bypass-capacitor and stability guidance, place input and output networks close to the device, and verify output settling for the intended closed-loop gain. Designers should also check noise, offset, input-bias-current, and capacitive-loading behavior against the specific signal source rather than relying only on nominal gain-bandwidth figures. This product page combines the manufacturer specifications with engineering-focused selection guidance, drop-in replacement information, application context, and practical PCB design notes. It also distinguishes temperature-grade and packaging variants within the MCP601 family so engineers can assess PCB reuse and production interchangeability before committing to a source.
MCP601T-E/ST - 2.8MHz R-R CMOS Op Amp | Microchip
The Microchip Technology MCP601T-E/ST is a single, general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, a 2.7 V to 6.0 V supply range, and a typical operating current of 230 uA. The device is packaged in an 8-pin TSSOP and provides rail-to-rail output swing, low bias current, high open-loop gain, and an input offset voltage below 2 mV. A CMOS operational amplifier is an active analog signal-conditioning device that uses high-input-impedance differential inputs to amplify the difference between two voltages. The amplifier sits in the signal-chain hierarchy between sensors, transducers, and analog sources on the input side and analog-to-digital converters, filters, control loops, and measurement equipment on the output side. The MCP601 family is designed for general-purpose applications requiring low power, rail-to-rail output operation, and single-supply operation from 2.7 V to 6.0 V. Key features include a 2.8 MHz gain-bandwidth product, which supports useful closed-loop bandwidth at modest gains, and typical operating current of 230 uA for battery-powered and portable systems. Rail-to-rail output swing allows the output to approach the supply rails under suitable load conditions. The less-than-2 mV input offset specification supports precision-enough DC amplification for sensor interfaces, filtering, buffering, and audio preamplifier stages, while low bias current helps preserve high source impedance. The MCP601 uses Microchip's advanced CMOS process technology to combine low power consumption with high open-loop gain and rail-to-rail output performance. Its 2.7 V minimum supply voltage supports 3.3 V systems, while the 6.0 V upper limit provides headroom for 5 V rails. Because stability, output swing, noise, and drive capability depend on supply voltage, load current, and feedback configuration, the manufacturer datasheet should be consulted for the operating curves and application limits used in a specific design. Typical uses include low-power sensor conditioning, current-to-voltage conversion, analog filtering, audio signal amplification, battery-powered instrumentation, and general buffering around microcontrollers. The TSSOP package is appropriate for compact surface-mount designs, while the low operating current is useful when the amplifier must operate continuously from a limited energy source. When laying out the circuit, place the bypass capacitor close to the supply pin and keep feedback traces short to minimize noise pickup and unwanted coupling. Verify the required common-mode range, output swing, capacitive-load drive, and stability for the selected gain before releasing the layout. This page combines manufacturer specifications, sourcing information, application guidance, and same-footprint alternatives for faster component evaluation.
MCP601T-I/OT - 2.8MHz RRO CMOS Op Amp | Microchip Technology
The Microchip Technology MCP601T-I/OT is a single-circuit, rail-to-rail CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, and typical input offset voltage below 2 mV, housed in a 5-pin SOT-23 surface-mount package. It operates from a single 2.7 V to 6.0 V supply and combines low bias current with high operating speed. An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The MCP601 belongs to the CMOS operational-amplifier hierarchy, where low power consumption and low input bias current support battery-powered and high-impedance signal chains. Its rail-to-rail output stage allows the output voltage to approach the supply rails, improving useful signal range in low-voltage systems. Three headline characteristics define the MCP601T-I/OT: its 2.8 MHz gain-bandwidth product supports higher-frequency closed-loop operation than very-low-bandwidth amplifiers, its 230 uA typical operating current suits low-power designs, and its offset voltage of less than 2 mV limits systematic input-referred error. The device uses Microchip advanced CMOS technology and provides rail-to-rail output swing, low bias current, high open-loop gain, and high speed. Because the gain-bandwidth product is 2.8 MHz, the amplifier is most appropriate for low-to-moderate frequency precision signal paths rather than high-speed video or RF tasks. Closed-loop bandwidth depends on the selected noise-gain topology; for example, a non-inverting amplifier configured for 10-times gain has a much lower usable bandwidth than a unity-gain configuration. Input offset, bias current, output swing, supply voltage, and stability determine practical precision. Typical uses include low-power sensor conditioning, portable instrumentation, audio preamplification, active filtering, and general-purpose analog signal processing. The single 2.7 V to 6.0 V supply range makes the device suitable for systems using 3.3 V or 5 V rails. Its low operating current is beneficial in battery-operated equipment where every milliampere affects operating time. When laying out the PCB, keep the op-amp input pins away from switching nodes, high-current traces, and digital clock lines. Place input and feedback components close to their associated pins, use a solid ground reference, and follow the stability and decoupling recommendations in the manufacturer documentation. The unused supply pin must be connected to the appropriate supply or ground potential rather than left floating. This product page combines the manufacturer specifications with package, application, replacement, and design guidance. It also distinguishes the industrial-temperature MCP601T-I/OT from other mechanically related variants, helping engineers identify a valid board-level replacement without confusing package compatibility with functional equivalence.
MCP601T-I/SN - 2.8MHz Low-Power Op Amp | Microchip
The Microchip Technology MCP601T-I/SN is a single, low-power CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage, packaged in an 8-pin SOIC. It operates from a 2.7 V to 5.5 V supply and provides rail-to-rail output swing with a common-mode input range extending below ground. An operational amplifier is a voltage-feedback amplifier used to increase signal amplitude, buffer high-impedance sources, compare voltages, or drive external loads through feedback. The MCP601 belongs to the broader CMOS operational-amplifier hierarchy, combining low input bias current, moderate gain bandwidth, high open-loop gain, and rail-to-rail output capability in a low-power integrated circuit. Its 2.8 MHz gain-bandwidth product supports general-purpose signal conditioning at moderate frequencies. The 230 uA typical operating current is useful for portable and low-power systems, while the less-than-2 mV typical input offset supports precision-oriented applications. Rail-to-rail output operation maximizes usable output swing from a 2.7 V to 5.5 V supply, and the common-mode input range below ground simplifies single-supply sensing near zero volts. The advanced CMOS implementation provides low bias current, high-speed operation, and high open-loop gain. With unity-gain stability, the device can be configured as a non-inverting or inverting amplifier without an additional compensation network. Its low quiescent current makes it appropriate for continuously powered sensor circuits, where every microampere contributes to the overall system power budget. Typical uses include current sensing, portable instrumentation, sensor signal conditioning, low-frequency active filters, audio input stages, and industrial control interfaces. The 8-pin SOIC format is suitable for conventional surface-mount assembly, while the operating range and low-power characteristics support designs operating from regulated 3.3 V or 5 V rails. For stable operation, place input and feedback components close to the amplifier pins, avoid long high-impedance input traces, and provide adequate bypassing between VDD and VSS. Common-mode and output-headroom checks are essential when operating near the supply rails, particularly with 2.7 V systems. This page combines manufacturer specifications, sourcing guidance, drop-in family alternatives, comparison data, and practical circuit-design notes. These resources help engineers evaluate the MCP601T-I/SN beyond basic catalog parameters and select it for low-power, rail-to-rail signal-processing applications.
MCP601T-I/ST - 2.8MHz Rail-to-Rail CMOS Op Amp | Microchip
The Microchip Technology MCP601T-I/ST is a single-circuit, general-purpose operational amplifier with a 2.8 MHz gain-bandwidth product, rail-to-rail output operation, and a typical operating current of 230 uA in an 8-pin TSSOP package. Its typical input offset voltage is less than 2 mV, while the listed input bias-current characteristic is 1 pA. The MCP601 family uses Microchip's advanced CMOS technology and is intended for low-power, low-voltage analog signal-conditioning circuits. An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential feedback to amplify a voltage difference. It belongs to the amplifier IC hierarchy: operational amplifier -> voltage-feedback amplifier -> analog signal conditioning -> semiconductor. The rail-to-rail output architecture allows the output to approach the available supply rails more closely than a conventional fixed-headroom output stage, which is valuable in compact systems that require a usable output swing from a low-voltage supply. The MCP601T-I/ST combines a 2.8 MHz gain-bandwidth product with low typical operating current of 230 uA. Its listed typical input offset voltage is below 2 mV, and the LCSC product listing identifies a 1 pA input bias-current figure. A slew rate of 2.3 V/us is also listed for the device. These characteristics place it between general-purpose signal amplification and low-power acquisition applications where low quiescent consumption and rail-to-rail output capability are more important than very high bandwidth. The MCP601 uses advanced CMOS technology to support low-power operation and high input impedance. Rail-to-rail output capability is particularly useful for buffer, transducer, and sensor-interface stages that operate near either supply rail. Designers should still account for input common-mode range, output swing, noise, stability with the selected feedback network, and decoupling when applying the amplifier outside its simplest voltage-follower configuration. The exact MCP601T-I/ST ordering suffix identifies the industrial temperature and TSSOP packaging option. Typical uses include low-power sensor conditioning, battery-powered instrumentation, ADC input buffering, current-to-voltage conversion with a feedback resistor, general signal amplification, and unity-gain buffers. The 8-TSSOP package supports compact PCB layouts, while the 230 uA typical operating current helps reduce the energy burden in continuously powered systems. Because the listed 2.8 MHz bandwidth is modest compared with high-speed amplifiers, the MCP601T-I/ST is best suited to low- and intermediate-frequency signal paths rather than wideband pulse or video amplification. For a new design, use the manufacturer datasheet pin description and typical-application circuit when assigning pins and compensation or feedback values. Keep input and output nodes short, provide local supply bypassing, and verify the input common-mode and output-voltage limits against the actual operating rail. The Request a Quote form on this page provides current commercial availability, lead-time, and order information without embedding a static price. This product page combines manufacturer specifications, package information, practical design guidance, drop-in replacement analysis, and a parameter comparison for the MCP601T-I/ST. It also distinguishes the verified TSSOP option from other MCP601 package and ordering variants, helping engineers identify a suitable replacement before committing to a PCB revision.
MCP602-E/P - 2.8MHz Dual CMOS Op Amp | Microchip
The Microchip Technology MCP602-E/P is a dual general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 2.3 V/us slew rate, and an 8-lead PDIP package. Its typical operating current is 230 uA per amplifier, its typical input offset voltage is below 2 mV, and its specified supply range is 2.7 V to 5.5 V. The device provides rail-to-rail output swing and low bias current, making it suitable for portable, industrial, and signal-conditioning systems. A CMOS operational amplifier is a voltage-controlled differential amplifier implemented with complementary metal-oxide-semiconductor transistors. In the broader electronics hierarchy, an op amp belongs to analog integrated circuits, then amplifiers, then voltage-feedback operational amplifiers, and finally low-power CMOS operational amplifiers. MCP602 combines two independent amplifiers in one package, reducing board area in dual-channel sensor, filtering, buffering, and control circuits. Key features include a 2.8 MHz gain-bandwidth product, 2.3 V/us slew rate, less-than-2 mV typical offset voltage, and 230 uA typical operating current. Rail-to-rail output swing allows the output to approach its supply limits under suitable load conditions, which is useful for low-voltage systems. The dual configuration supports common applications in industrial process control, battery-operated equipment, portable products, data acquisition, test equipment, and low-end audio systems. The MCP602 family is specified for 2.7 V to 5.5 V operation according to the verified manufacturer and distributor material. A separate search result also describes the family as supporting a 2.7 V to 6.0 V single-supply range; because the official product-page result explicitly states 2.7 V to 5.5 V, that verified range is used here. CMOS construction supports low bias current and low power consumption, while the 2.8 MHz bandwidth is adequate for general-purpose low-frequency analog signal conditioning rather than demanding high-speed video or RF stages. Typical applications include two-channel sensor conditioning, portable battery-powered instrumentation, industrial control loops, low-frequency active filters, voltage buffers, audio preamplification, and general data-acquisition front ends. In each case, the designer should verify output swing, input common-mode range, noise, stability, and load drive against the complete operating conditions. The 8-lead PDIP package is suitable for through-hole prototypes, legacy industrial boards, and designs where a dual amplifier in a standard DIP footprint simplifies assembly. For PCB design, place bypass capacitors close to the supply pins and keep analog input and output traces short and away from switching nodes. A common single-supply error is assuming the input common-mode range equals the full rail-to-rail output range; verify the family datasheet for the exact input limits before using the amplifier as a comparator or precision level shifter. This page consolidates verified specifications, sourcing information, design guidance, and explicit data gaps without adding unverified technical claims.
MCP602-E/SN - 2.8 MHz Dual RRO Op Amp | Microchip
The Microchip Technology MCP602-E/SN is a dual general-purpose CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current per amplifier, and less than 2 mV offset voltage. The device is packaged in an 8-pin SOIC and supports single-supply operation from 2.7 V to 6.0 V. An operational amplifier, or op amp, is a voltage-gain stage used to amplify weak signals, buffer sensors, perform active filtering, compare voltages, and drive analog-to-digital or digital-to-analog converters. The MCP602 belongs to the CMOS operational-amplifier hierarchy, combining low bias current, rail-to-rail output swing, unity-gain stability, and relatively high speed in a low-power analog signal-conditioning IC. The headline features suit compact, low-power analog systems. Its 2.8 MHz gain-bandwidth product supports signal bandwidths well below the unity-gain limit, while the 2.3 V/us typical slew rate provides adequate response for sensor signals and general-purpose instrumentation. Rail-to-rail output swing improves usable output range on low-voltage supplies, and the input range includes ground, allowing operation near the lower supply rail when suitable biasing is applied. Microchip's advanced CMOS process gives the MCP602 low bias current, high open-loop gain, and low typical operating current of 230 uA per amplifier. The dual configuration provides two amplifiers in one 8-pin SOIC, reducing board area compared with two separate single-amplifier packages. Unity-gain stability permits direct voltage-follower use without an external compensation network. Typical uses include industrial process-control loops, portable and battery-operated instruments, data-acquisition front ends, test equipment, and low-end audio signal paths. Each channel can amplify a sensor output, buffer a high-impedance source, implement an active filter, or drive a converter input. The combination of low power and rail-to-rail output is especially useful for systems powered from 3.3 V or 5 V supplies. Designers should verify the input common-mode range, output swing, capacitive-load stability, noise, and output-current capability for the exact operating conditions. Place the bypass capacitor close to the supply pins, use a solid ground reference, and avoid excessive loading on the output. The SOIC outline permits standard surface-mount assembly, but exposed-pad thermal considerations do not apply to this package. This page combines the manufacturer product information with package, pinout, comparison, selection, and practical circuit guidance to help engineers evaluate the MCP602-E/SN without reconstructing the complete design context from separate catalog entries.
MCP602-E/ST - Dual 2.8MHz CMOS Op Amp | Microchip Technology
The Microchip Technology MCP602-E/ST is a dual CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, typical operating current of 230 uA, offset voltage below 2 mV, and rail-to-rail output swing in an 8-lead TSSOP package. The two amplifiers share a common supply and are intended for low-power signal-processing systems that require more than one amplifier per board area. An operational amplifier, or op amp, is a high-gain differential amplifier whose open-loop behavior is controlled by negative feedback. Within the broader semiconductor hierarchy, an op amp is an analog amplifier IC used in signal conditioning, sensing, filtering, buffering, and control systems. Rail-to-rail output swing allows the MCP602 output to approach its supply rails more closely than a conventional output stage, which is useful when the available signal headroom is limited. The MCP602 uses Microchip's advanced CMOS technology to provide low bias current and low power consumption. Its 2.8 MHz gain-bandwidth product is suitable for general-purpose closed-loop signal paths rather than high-frequency precision instrumentation. The typical operating current of 230 uA supports battery-operated equipment, while the offset voltage specification of less than 2 mV provides a useful indication of input-stage matching. The device also provides high open-loop gain and low-bias operation, as stated on the manufacturer product page. The MCP602 family is available in standard PDIP, SOIC, and TSSOP packages, and the MCP602-E/ST ordering code places the dual amplifier in an 8-lead TSSOP. This surface-mount package supports compact layouts in industrial process control, low-power battery-operated devices, portable equipment, data-acquisition systems, test equipment, and low-end audio products. Dual packaging can reduce board area when a circuit requires amplification, buffering, or active filtering in more than one channel. For portable and low-power designs, compare the MCP602's 230 uA typical operating current with the signal accuracy and bandwidth required by the application. Designers should also verify the complete operating-voltage range, electrical limits, input-bias current, noise performance, output-current capability, and temperature limits against the current manufacturer datasheet before releasing production hardware. MCP602-E/ST drop-in alternatives should be evaluated primarily by package and pin compatibility, followed by supply voltage, gain-bandwidth product, input bias current, offset voltage, output swing, and operating current. Exact substitution is not assured when the required specifications differ, even if the amplifier functions appear similar. This page combines the verified manufacturer and distributor information with practical selection, application, and design guidance. The resulting product record is intended to help engineers identify the correct TSSOP footprint, compare available alternatives, and develop an appropriate low-power analog signal path. Manufacturer documentation remains the controlling authority for ratings, test conditions, pin functions, package drawings, and revised production limits.
MCP602-I/P - 2.8 MHz Dual CMOS Op Amp | Microchip
Microchip Technology MCP602-I/P is a dual CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current per amplifier, and less than 2 mV input offset voltage, supplied in an 8-lead PDIP package. The amplifier operates from a single supply of 2.7 V to 6.0 V and supports rail-to-rail output operation with input common-mode range including ground. These characteristics position the MCP602-I/P as a low-power general-purpose amplifier for industrial process control, battery-operated equipment, portable instrumentation, data acquisition, test equipment, and low-end audio systems. An operational amplifier, or op amp, is a high-gain differential amplifier whose feedback network determines the gain of a closed-loop circuit. The MCP602 belongs to the hierarchy CMOS operational amplifier, analog amplifier, signal-conditioning IC, and broader power-management and semiconductor categories. Its two independent amplifier channels allow one package to implement functions such as voltage followers, transimpedance amplifiers, active filters, comparators, and level-shifting stages when supply and input ranges are appropriate. The MCP602-I/P combines several useful low-power characteristics. Its 2.8 MHz gain-bandwidth product provides more bandwidth than typical micropower amplifiers, while the 230 uA typical operating current supports portable and battery-powered designs. Input bias current of 1 pA typical is particularly useful with high-impedance sensors. A unity-gain-stable architecture allows direct voltage-follower use, and the input common-mode range extending to ground simplifies single-supply signal conditioning. The rail-to-rail output improves usable output swing in low-voltage systems. Microchip advanced CMOS technology provides low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. The device contains two independent amplifiers rather than one channel, making the 8-lead PDIP suitable for dual-stage analog signal paths. Its minimum operating supply of 2.7 V permits use from regulated 3.3 V systems, while the 6.0 V maximum supports conventional 5 V analog rails within the stated operating range. Typical applications include low-power sensor interfaces, portable measurement systems, industrial process-control circuits, data-acquisition boards, test equipment, and low-end audio amplification or conditioning. In a transimpedance stage, the 1 pA typical input bias current helps limit photocurrent-generated error. In a voltage follower, unity-gain stability and the input range including ground simplify buffering of signals produced by sensors operating near 0 V. Designers should verify signal amplitude, output swing, input common-mode range, noise, and stability under the intended loading before assigning the amplifier to a circuit. The PDIP package is convenient for prototyping, breadboards, and through-hole industrial assemblies, but its lead spacing differs from surface-mount packages. Decoupling and grounding remain important even though the MCP602-I/P is intended for low-power analog systems. This product record combines manufacturer specifications, distributor availability, package information, engineering application guidance, and verified drop-in alternatives. It also distinguishes parameter differences among candidate devices so engineers can select a replacement without mistaking a same-family amplifier for a pin-compatible substitute.