بەرهەمەکان (5,100+)

LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC
LAN91C111I-NU-E2

LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC

The SMSC Corporation LAN91C111I-NU-E2 is a single-chip 10/100 Ethernet controller with an integrated physical layer, parallel host interface, and non-PCI architecture, housed in a 128-pin TQFP package measuring 14 x 14 mm. It supports 10 Mbps and 100 Mbps Ethernet operation according to IEEE 802.3 and IEEE 802.3u, while operating from a 2.97 V to 3.63 V core supply. An Ethernet controller is an interface integrated circuit that connects an embedded processing system to a physical Ethernet network. In the hierarchy, the LAN91C111 belongs to Ethernet controllers, interface ICs, integrated circuits, and semiconductors. Integrating the MAC and PHY reduces the number of components required for an embedded Fast Ethernet port, while the parallel interface provides direct access between the controller and external host-bus circuitry. The LAN91C111 uses a four-bit Media Independent Interface for connections to either 10 Mbps or 100 Mbps Ethernet networks. Three device pins support the two-wire serial MII management protocol. This combination allows the controller to participate in MII-based network designs without requiring the parallel interface to be limited to one Ethernet speed. The controller is intended for embedded systems requiring dedicated Fast Ethernet connectivity rather than a PCI-based desktop adapter. The device is identified as a 10/100 Base-T/TX PHY controller with a parallel host interface. Its 128-TQFP package provides the mixed-signal and digital connections needed for the MAC, PHY, host interface, and MII functions. Because it combines analog and digital circuitry on one device, PCB implementation requires controlled trace routing, suitable grounding, and careful separation of high-speed digital signals from sensitive network and clock connections. Typical applications include embedded industrial controllers, test equipment, print servers, communications appliances, and other systems requiring a compact 10/100 Ethernet interface. The integrated MAC and PHY are especially useful when a system cannot accommodate a discrete Ethernet PHY or a separate PCI Ethernet controller. The parallel host interface must still be matched carefully to the target processor, bus logic, and firmware architecture. When designing around the LAN91C111I-NU-E2, verify the host-bus timing, MII connections, magnetic-interface implementation, and available board area before releasing a PCB layout. The 128-pin package is not physically interchangeable with smaller Ethernet interfaces without a complete board redesign, so footprint and firmware compatibility are as important as nominal Ethernet performance. This page combines the manufacturer interface information, package identification, ordering details, and engineering guidance for the LAN91C111I-NU-E2. It also documents the distinctions among related LAN91C111 ordering codes and provides practical considerations for evaluating this non-PCI Ethernet controller in an embedded Fast Ethernet design.

RFQ پەیوەندی
LAN91C113-NC 10/100 Ethernet MAC/PHY | Microchip Technology
LAN91C113-NC

LAN91C113-NC 10/100 Ethernet MAC/PHY | Microchip Technology

The Microchip Technology LAN91C113-NC is a 16-bit 10/100 Base-T Ethernet single-chip MAC and PHY controller. It combines media-access control, physical-layer signaling, and a parallel host interface in one integrated circuit, reducing the component count required for embedded Ethernet connectivity. The controller is associated with the SMSC FEAST family and is identified in the manufacturer catalog as LAN91C113. An Ethernet MAC and PHY single-chip controller is an interface IC that connects an embedded host processor to a copper Ethernet network. The MAC handles Ethernet frame processing and host-facing data exchange, while the PHY converts between digital signaling and the physical signals used on 10/100 Base-T networks. In the broader semiconductor hierarchy, the device belongs to Ethernet controllers, interface controllers, integrated circuits, and networked embedded systems. The principal feature of the LAN91C113-NC is its combination of a 16-bit parallel host interface with an integrated 10/100 Ethernet MAC and PHY. This integration can simplify embedded networking designs that previously required separate Ethernet controller and physical-layer devices. The 16-bit interface provides a direct path between the controller and a compatible host processor, while on-chip Ethernet physical-layer functionality supports connection to a network transformer and magnetics. The LAN91C113 family is associated with SMSC's FEAST Fast Ethernet controller technology. Its architecture is intended to provide Ethernet connectivity in embedded systems where a non-PCI parallel interface is preferable to a PCI-based controller. The combined MAC and PHY arrangement also reduces board-level integration complexity by consolidating the digital controller and physical-layer transceiver into one package. Typical uses for this controller include industrial embedded platforms, data acquisition equipment, communications modules, embedded test systems, and legacy controller-based products being connected to 10/100 Ethernet. It is particularly relevant when the host processor already provides a 16-bit parallel bus and the design needs a dedicated Ethernet interface rather than an integrated network controller in the processor itself. Design work should begin with the manufacturer pin-description and reference-circuit sections, including the external clock, reset, magnetics, decoupling, and network-isolation requirements. PCB signal integrity is particularly important because the device combines parallel host signaling with Ethernet physical circuitry. Maintain the specified component placement and controlled impedance around the Ethernet network path, and use the manufacturer reference design as the basis for a first revision. This product page combines the device identity, catalog description, distributor records, package guidance, application analysis, and engineering design notes into one purchasing resource. It also distinguishes direct ordering information from replacement analysis so engineers can assess fit, interface compatibility, and board-level integration before committing a design.

RFQ پەیوەندی
LAN91C113-NE - 10/100 Ethernet MAC PHY | SMSC
LAN91C113-NE

LAN91C113-NE - 10/100 Ethernet MAC PHY | SMSC

The SMSC LAN91C113-NE is a highly integrated 10/100 Ethernet MAC and PHY solution for embedded networking, with support for 10Base-T and 100Base-TX Ethernet applications. It combines a 10/100 Ethernet Media Access Controller with a physical-layer transceiver in one device, reducing the component count and simplifying the hardware architecture of embedded network equipment. The LAN91C113-NE is associated with a 128-lead TQFP package configuration for compact surface-mount PCB designs. An Ethernet MAC is the controller that manages frame transmission and reception between a host processor and the physical network medium. The PHY converts digital data into the electrical signaling required by 10Base-T and 100Base-TX Ethernet. Integrating both functions in one IC gives embedded designers a single network interface component that connects to a host system through a parallel interface and uses standard Ethernet magnetics and cabling for the physical network connection. The LAN91C113-NE is positioned for designs requiring 10/100 Ethernet connectivity rather than gigabit Ethernet. It can support industrial controllers, embedded gateways, print servers, set-top equipment, test instruments, and other network-enabled products. Because the MAC and PHY are combined, board designers can reduce the number of separate network-interface ICs and simplify the relationship between software control, packet handling, and physical-layer signaling. In a typical embedded design, the host processor connects to the LAN91C113-NE for frame exchange, while the Ethernet PHY section connects through the required external network interface components. The device is intended for 10Base-T and 100Base-TX links, making it appropriate for legacy and cost-sensitive Ethernet installations where 100 Mbit/s operation is sufficient. Software drivers and host-side configuration are necessary to initialize the controller and manage Ethernet traffic. The principal engineering consideration is interface and system integration. The design must provide the correct power rails, decoupling, clocking, reset behavior, host-bus connections, and Ethernet magnetic interface required by the selected board architecture. Pin assignment, voltage levels, timing, and exposed-package details should be confirmed against the manufacturer datasheet before the PCB footprint is released. LAN91C113-NE is a practical choice when an embedded product needs a dedicated 10/100 Ethernet MAC-PHY with a parallel host interface in a surface-mount package. Its value comes from combining controller and transceiver functions, reducing board complexity while retaining support for both 10Base-T and 100Base-TX network operation. This product summary combines the manufacturer product information and distributor references for the LAN91C113-NE. The Request a Quote form on this page is the appropriate route for current commercial availability, pricing, and delivery information.

RFQ پەیوەندی
LAN91C113-NS - 100Mbps Ethernet Controller | Microchip
LAN91C113-NS

LAN91C113-NS - 100Mbps Ethernet Controller | Microchip

Microchip Technology LAN91C113-NS is a 100 Mbps Ethernet controller with integrated 10/100 Base-T/TX PHY and a parallel MII interface, supplied in a 128-QFP package. The device supports a 2.97 V minimum supply voltage, operates at 3.3 V, and is specified for a 0°C to 85°C temperature range. Its integrated MAC and PHY combine Ethernet packet processing and physical-layer connectivity in one IC. An Ethernet controller is an interface integrated circuit that connects a digital processor or system bus to an Ethernet network. The LAN91C113 belongs to the Ethernet interface controller category, which combines a media access controller, physical-layer transceiver, and host-facing parallel interface. This integration can reduce the number of external network components while providing a standardized 10/100 Ethernet connection for embedded equipment. The principal operating characteristics are a 100 Mbps data rate, compliance with IEEE 802.3 and IEEE 802.3u, MII host connectivity, and a 3.3 V supply. The listed supply current is 100 mA, while the operating temperature extends from 0°C to 85°C. These specifications position the device for industrial, communications, and embedded systems that use a parallel host interface instead of a serial media interface. The 128-QFP package provides the physical footprint and pin count needed for a substantial mixed-signal Ethernet interface. Because the MAC and PHY are integrated, PCB design requires careful separation of Ethernet signal routing, supply distribution, and grounding. The parallel MII interface should be routed according to the manufacturer's recommended layout and timing guidance to limit data-integrity and electromagnetic-interference issues. Typical uses include industrial Ethernet control equipment, embedded network gateways, data acquisition systems, print servers, and communication controllers. In each case, the device serves as the link between a host processor and a 10/100 Ethernet network. Its 3.3 V operation and commercial temperature range support compact systems where 100 Mbps connectivity is sufficient and a dedicated PHY is undesirable. Designers should confirm pin functions, timing, clocking, magnetics, and decoupling directly against the manufacturer datasheet before layout release. Particular attention should be given to MII clock timing, PHY termination, analog supply routing, and the separation between Ethernet traces and sensitive digital signals. These controls are more important than raw headline speed when establishing reliable network performance. This page organizes the LAN91C113-NS specifications, sourcing information, interface context, application guidance, and same-package replacement considerations. It also identifies which technical details require confirmation from the manufacturer documentation before a new PCB is released.

RFQ پەیوەندی
LAN91C113-NU - 10/100 Ethernet MAC/PHY | Microchip
LAN91C113-NU

LAN91C113-NU - 10/100 Ethernet MAC/PHY | Microchip

The Microchip Technology LAN91C113-NU is a 16-bit 10/100 Base-T/TX Ethernet controller that combines a non-PCI Media Independent Interface MAC and integrated PHY in a 128-pin TQFP package measuring 14 x 14 mm. It operates from a 3.3 V supply and connects a host processor through the parallel MII interface. An Ethernet MAC, or Media Access Control, manages frame transmission, reception, addressing, and access to the physical network medium. A PHY implements the physical signaling layer between the MAC and a twisted-pair cable. The LAN91C113 integrates both functions into one controller, reducing board area and external PHY count compared with a separate MAC and Ethernet transceiver design. The controller supports 10Base-T and 100Base-TX operation over a 16-bit parallel MII. This combination suits embedded systems that already have a host processor with a compatible parallel bus but do not include an Ethernet PHY. Integration can reduce board routing, connector requirements, and the number of components requiring firmware and driver support. The LAN91C113-NU belongs to the Ethernet interface IC and network interface controller hierarchy. Unlike a PCI-based Ethernet card, the parallel MII architecture connects directly to processor logic rather than a host peripheral bus. The 3.3 V operating supply is compatible with modern embedded processor systems, although the complete design must also satisfy the voltage requirements of attached memory, magnetics, and physical-layer circuitry. Typical applications include industrial monitoring equipment, building automation controllers, embedded test equipment, industrial gateways, and compact network appliances. A typical implementation places the controller and an Ethernet jack with integrated magnetics on the same PCB, connects the host processor to the MII signals, and configures the MAC and PHY through the device’s control interface. Design should begin with the manufacturer’s reference schematic and signal-integrity guidance. Route the parallel MII clock and data signals as a controlled-length group, provide the required decoupling, and follow the recommended magnetics and impedance-termination layout. Confirm that the host processor’s MII timing, voltage levels, interrupt requirements, and software driver support match the controller before committing the PCB layout. This page consolidates the product identity, package information, application guidance, comparison criteria, and practical integration considerations engineers need when evaluating the LAN91C113-NU for a 10/100 Ethernet design. Use the Request a Quote form on this page for current commercial availability, packaging, lead time, and sourcing support.

RFQ پەیوەندی
LAN91C93I-MC Full-Duplex Ethernet Controller | Microchip
LAN91C93I-MC

LAN91C93I-MC Full-Duplex Ethernet Controller | Microchip

Microchip Technology LAN91C93I-MC is a non-PCI single-chip full-duplex Ethernet controller with a 1.25 MB/s data rate, 10 Base-T PHY interface, CMOS process technology, and a 100-pin QFP package. It combines local-bus Ethernet controller functionality with independent transmit and receive operations for switched-Ethernet systems. An Ethernet controller is a semiconductor interface between a host processor and an Ethernet network. Within the product hierarchy, LAN91C93I-MC is an Ethernet controller, network interface controller, interface IC, and semiconductor. Its local-bus architecture avoids requiring a PCI bus while giving embedded processors direct access to Ethernet communication functions through a comparatively simple software interface. The controller supports full-duplex switched Ethernet and maintains independent transmit and receive operations. This architecture can improve effective communication concurrency compared with a controller that must coordinate both directions through one path. The 1.25 MB/s rated transfer rate and 10 Base-T PHY interface identify the LAN91C93I-MC as a 10 Mb/s-class embedded Ethernet solution rather than a Fast Ethernet or Gigabit Ethernet controller. According to the manufacturer datasheet, LAN91C93I is designed to be 100% software compatible with LAN91C92, LAN91C94, and LAN91C96 when operating in local-bus mode. This compatibility is particularly useful when preserving an established driver and application interface is more important than redesigning the entire network software stack. The integrated device also retains LAN91C92 functionality for local-bus environments. Typical applications include embedded industrial control, instrument networking, embedded appliance connectivity, point-of-sale equipment, and legacy embedded systems that require full-duplex switched Ethernet. The 100-QFP package exposes the controller's processor-side, memory-side, Ethernet, and power connections through a relatively high pin count suited to multilayer or through-hole-compatible board assembly. Designers should verify the complete pin description, voltage limits, clocking requirements, initialization sequence, and transceiver interface in the manufacturer datasheet before layout release. They should also confirm that the external magnetics, RJ-5 interface, isolation requirements, and system grounding topology suit the target network environment rather than assuming that the controller alone constitutes a complete Ethernet interface. This product overview combines the manufacturer interface description, package details, software-compatibility information, verified alternatives, and practical selection considerations. It also identifies where an engineer must consult the official datasheet for complete electrical limits and PCB implementation details.

RFQ پەیوەندی
LAN91C93I-ME 10BASE-T Ethernet Controller | Microchip
LAN91C93I-ME

LAN91C93I-ME 10BASE-T Ethernet Controller | Microchip

The Microchip Technology LAN91C93I-ME is a non-PCI single-chip full-duplex Ethernet controller with an integrated 10BASE-T PHY interface, supplied in a 100-pin TQFP package. It is designed for local-bus systems and supports independent transmit and receive operations. The manufacturer identifies the LAN91C93I as 100% software-compatible with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode. An Ethernet controller is an interface IC that connects a processor or embedded host to an Ethernet physical layer. In this device, the controller and 10BASE-T PHY functions are integrated into one device. That integration reduces the number of external interface components required in an embedded Ethernet design while retaining a direct local-bus software interface. The Ethernet controller category belongs to the broader network-interface hierarchy: Ethernet controller → network interface IC → interface IC → semiconductor. The principal feature is support for full-duplex switched Ethernet with independent transmit and receive paths. Full-duplex operation allows each direction to be active simultaneously, which improves link utilization compared with a shared half-duplex arrangement. The integrated 10BASE-T interface also provides compatibility with 10 Mb/s Ethernet infrastructure. The -ME ordering code identifies the specific package and product configuration, while the -I family designation denotes the industrial-oriented LAN91C93I device family described by Microchip. The LAN91C93I architecture incorporates LAN91C92 local-bus functionality and extends it for switched full-duplex Ethernet. According to the manufacturer datasheet, independent transmit and receive operations allow the controller to manage both traffic directions concurrently. Existing local-bus software can also be reused because the LAN91C93I is stated to be 100% software-compatible with LAN91C92, LAN91C94, and LAN91C96 when operated in local-bus mode. Typical uses include embedded industrial controllers, local-bus embedded systems, legacy platform upgrades, and equipment that requires a dedicated 10BASE-T network interface without PCI. Its software continuity makes it especially relevant when an existing local-bus network stack must be retained while the physical network is converted to full-duplex switched Ethernet. Careful initialization, bus timing, and PHY integration remain essential during board bring-up. For a new design, first confirm that the host bus, address map, interrupt structure, and Ethernet driver expectations match the LAN91C93I register and software model. Review the manufacturer datasheet pin-description table and typical application circuit before assigning signals or laying out the 100-pin TQFP footprint. Also verify the selected magnetic-component and Ethernet-connector implementation against the required 10BASE-T topology. This product page combines the verified manufacturer overview, package information, software-compatibility relationships, application guidance, and practical selection criteria. It also distinguishes confirmed drop-in candidates from options that require board-level verification, helping engineers compare legacy Ethernet-controller options without treating software equivalence as automatic hardware equivalence.

RFQ پەیوەندی
LAN91C93I-MS - 10Mbps Ethernet Controller | Microchip
LAN91C93I-MS

LAN91C93I-MS - 10Mbps Ethernet Controller | Microchip

The Microchip Technology LAN91C93I-MS is a single-chip, non-PCI Ethernet controller with a 10 Mbps IEEE 802.3 10BASE-T PHY interface, supplied in a 100-pin QFP package measuring 14 x 20 mm. It combines an Ethernet media-access controller with a local-bus interface and is designed for embedded systems that require compact, software-compatible Ethernet connectivity. The controller operates from 3.3 V or 5 V supply rails and is available in tray packaging as LAN91C93I-MS. An Ethernet controller is an interface IC that manages frame transmission and reception between a host processor and an Ethernet physical layer. In this product hierarchy, the LAN91C93I integrates an IEEE 802.3 Ethernet MAC, a 10BASE-T PHY interface, and a local-bus host interface. This integration reduces external component count compared with a design using a separate network controller and physical-layer transceiver, while preserving a conventional processor-facing software interface. Key features include a 10 Mbps data rate, support for full-duplex switched Ethernet, and independent transmit and receive operations. The LAN91C93I architecture incorporates the local-bus functionality associated with the LAN91C92 family. The manufacturer datasheet also states that the controller is 100% software compatible with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode, which can simplify firmware migration among supported controller generations. The controller uses a local-bus architecture rather than a PCI interface, making it appropriate for embedded processors and custom bus designs that do not expose PCI host connectivity. Its integrated 10BASE-T PHY interface connects the digital Ethernet controller to a compliant network physical layer. Support for full-duplex switched Ethernet permits simultaneous sending and receiving, unlike designs restricted to half-duplex shared-network operation. Typical uses include industrial monitoring equipment, embedded test systems, legacy factory controls, serial-to-Ethernet equipment, and compact data-acquisition platforms. In these systems, the local-bus interface connects the Ethernet controller to a host processor, while the 10BASE-T PHY interface connects the board to copper Ethernet. Designers should confirm the required host-bus timing, transceiver characteristics, and electrical isolation before integrating the controller into a new design. The principal design consideration is interface compatibility. LAN91C93I is intended to maintain software compatibility with selected LAN91C92, LAN91C94, and LAN91C96 devices in local-bus mode, but software compatibility alone does not guarantee unconditional PCB interchangeability. Confirm package dimensions, pin assignments, supply sequencing, clock requirements, and transceiver characteristics in the manufacturer datasheet before releasing a replacement or respin. This page organizes the controller’s key electrical, packaging, compatibility, application, and design information into an engineering-focused reference. It also distinguishes verified drop-in candidates from broader software-compatible family members, helping procurement and design teams assess replacements with the appropriate technical checks.

RFQ پەیوەندی
LAN91C93I-MU - 10 Mbps Ethernet Controller | Microchip | TQFP-100
LAN91C93I-MU

LAN91C93I-MU - 10 Mbps Ethernet Controller | Microchip | TQFP-100

The Microchip Technology LAN91C93I-MU is a non-PCI, single-chip 10 Mbps Ethernet controller supporting IEEE 802.3 and a 10BASE-T PHY interface in a 100-pin TQFP package measuring 14 x 14 mm. It operates from a 3.3 V supply, with some catalog listings identifying compatibility with 3.3 V and 5 V systems. The controller provides integrated local-bus networking, full-duplex switched Ethernet operation, independent transmit and receive paths, and an enhanced transmit queue for efficient packet management. Its 100-TQFP footprint supports conventional surface-mount PCB assembly rather than a legacy PC/PCI bus interface. The LAN91C93I architecture combines local-area-network controller functionality with a simple software interface and retains compatibility with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode. These characteristics make the device suitable for embedded Ethernet equipment that requires deterministic network connectivity without requiring a PCI host interface. The LAN91C93I-MU is identified by Microchip as LAN91C93I with the -MU ordering suffix and is supplied in a green 100-pin QFP package. Designed for industrial-temperature operation, the device is specified from -40°C to +85°C. A typical design uses the controller with external magnetic isolation for the Ethernet physical layer, a 3.3 V supply, a local host processor connected through the device's parallel host bus, and an RJ45 network interface. The controller supports 10BASE-T rather than 100BASE-TX, so link speed and physical-layer requirements must be matched to legacy or cost-sensitive Ethernet equipment. Because the LAN91C93I is not a PCI Ethernet peripheral, host-bus timing, address mapping, interrupt connectivity, and software driver configuration are central PCB considerations. Its integrated architecture reduces the number of external networking components while preserving a conventional microcontroller or processor interface. An Ethernet controller is an interface integrated circuit that manages frame transmission, reception, buffering, addressing, and host communication for an Ethernet network. The LAN91C93I belongs to the local-bus controller hierarchy, combining an Ethernet MAC, protocol handling, and PHY-interface logic into one device. Its IEEE 802.3 and 10BASE-T support connect it to the Ethernet physical-layer ecosystem, while full-duplex switched Ethernet capability allows transmit and receive traffic to proceed independently. This integration places the LAN91C93I between a host processor and an Ethernet transceiver, simplifying the hardware architecture compared with a solution using a discrete network controller and additional interface glue. Key device characteristics include 10 Mbps Ethernet operation, a 10BASE-T PHY interface, full-duplex switched Ethernet support, independent transmit and receive operations, and an enhanced transmit queue. The controller's local-bus mode software compatibility with the LAN91C92, LAN91C94, and LAN91C96 can simplify firmware migration when an existing product family already uses those controllers. Its non-PCI architecture also provides an important alternative for embedded systems whose processors do not expose a conventional PCI bus. The 100-TQFP package provides enough pins for the parallel host interface, control signals, memory connections, and Ethernet-related signals, but it also requires careful escape routing and multilayer-board planning. The specified -40°C to +85°C operating range suits industrial equipment where commercial-temperature components would be insufficient. Technically, the LAN91C93I combines local-area-network controller functions with an enhanced transmit queue and fully independent receive and transmit operations. The enhanced queue allows the software driver to stage packets more effectively, which is valuable in systems where network traffic must be transferred between an external processor and the Ethernet medium without blocking host execution. The PHY interface follows 10BASE-T requirements rather than 100BASE-TX, determining the external magnetics, connector, line-driver, and cable requirements of the board. Local-bus software compatibility with four related controller families reduces the amount of low-level networking code that must be rewritten, although drivers should still be checked for register, interrupt, and device-option differences. The device is manufactured in CMOS technology and is specified as a green package, supporting lead-free assembly processes where its production documentation confirms the appropriate soldering profile. Typical applications include industrial control terminals, embedded instrumentation, legacy network gateways, factory-floor controllers, and compact embedded networking modules. In each case, the controller provides a conventional Ethernet interface to a host processor while managing frames, transmit queuing, and receive activity in hardware. A 10BASE-T-only design is appropriate for legacy infrastructure, isolated point-to-point links, or equipment where 10 Mbps is sufficient and component cost matters. It may also serve as a migration interface when an established product already contains LAN91C92-, LAN91C94-, or LAN91C96-compatible software. Modern high-bandwidth gateways generally require a faster Ethernet controller, but the LAN91C93I remains useful where software continuity and local-bus integration outweigh throughput. The primary PCB design consideration is the parallel host-bus and memory-interface routing required by a 100-pin TQFP. Place decoupling capacitors close to each applicable supply pin, maintain short high-speed Ethernet paths between the controller, external PHY components, magnetics, and RJ45 connector, and provide solid ground-plane continuity under the device. Keep analog and digital return currents separated where the board stackup permits, and follow the manufacturer's recommended pinout and reference circuitry. Verify the external network interface against the 10BASE-T design requirements rather than assuming that a 100BASE-T magnetics assembly is interchangeable. This page combines manufacturer and distributor product facts with package, application, purchasing, and replacement guidance to support early design decisions. It distinguishes verified electrical and package characteristics from parameters that require confirmation in the complete manufacturer datasheet, helping engineers qualify the LAN91C93I-MU for embedded Ethernet designs before committing to a PCB layout or production release.

RFQ پەیوەندی
LAN91C96-MS - 10/100 Ethernet Controller | Microchip
LAN91C96-MS

LAN91C96-MS - 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN91C96-MS is a single-chip 10/100 Ethernet controller with a 3.3 V supply, a 100-pin QFP package measuring 14 x 20 mm, and an operating temperature range of -40 °C to 85 °C. It integrates an Ethernet MAC, physical-layer encoding and decoding functions, packet RAM, and host-bus connectivity, reducing the component count required for embedded Ethernet designs. An Ethernet controller is an interface IC that connects an embedded host processor to a physical Ethernet network. Within the product hierarchy, the LAN91C96-MS is an Ethernet MAC and physical-layer controller, which is part of a communications interface IC and ultimately a semiconductor. It supports non-PCI systems using Local Bus, PCMCIA, or Motorola 68000 bus interfaces instead of requiring a PCI-compatible host. Key features include full-duplex switched Ethernet support, enhanced transmit queue management, integrated packet RAM, and support for AUI and twisted-pair network connections. The supplied manufacturer information identifies the LAN91C96 family as integrating most IEEE 802.3 functionality, including MAC protocol handling, physical-layer encoding and decoding, twisted-pair transceiver functions, and link-integrity testing. The controller addresses legacy embedded platforms that need Ethernet connectivity without a PCI bus. Its local-bus addressing uses A0-A9 and A15 together with active-low nREG, nCE1, nWE, and nOE signals. Word reads from odd byte addresses can return a zero value in the upper byte because that byte is a don't-care under the referenced PCMCIA attribute-memory access rule. Typical uses include legacy embedded systems, industrial controllers, compact network adapters, PC Card LAN equipment, and custom communication equipment requiring a non-PCI Ethernet interface. The manufacturer also identifies the low-profile TQFP option as suitable for mobile applications such as PC Card LAN adapters, although the verified LAN91C96-MS ordering information identifies a 100-pin QFP package. Designers should verify the exact PCB footprint, clock source, bus timing, transceiver connections, and power requirements against the manufacturer datasheet before substituting this legacy controller. The -40 °C to 85 °C specification supports industrial-temperature designs, but applications needing a wider commercial range should select a variant with the appropriate documented rating. This page consolidates verified distributor identification, manufacturer product information, datasheet details, interface features, and package data. It also separates documented facts from unresolved parameters and avoids presenting unspecified pricing, pin names, and competitor compatibility as confirmed engineering data.

RFQ پەیوەندی
LAN91C96-MU - 10Mbps Ethernet Controller | Microchip Technology
LAN91C96-MU

LAN91C96-MU - 10Mbps Ethernet Controller | Microchip Technology

Microchip Technology LAN91C96-MU is a single-chip 10Mbps Ethernet controller with a 10BASE-T PHY, parallel host interface, MAC functions, and integrated packet RAM in a 100-pin TQFP package measuring 14 x 14 mm. The device supports 3.3 V and 5 V operation and combines Local Bus, PCMCIA, and Motorola 68000 bus interfaces in one CMOS Ethernet controller. Its integrated architecture reduces the external component count required for embedded Ethernet connectivity while providing full-duplex switched Ethernet support, enhanced transmit queue management, and 6 kB of packet RAM. An Ethernet controller is an interface IC that connects a host processor or embedded system to an Ethernet physical network. The LAN91C96 family integrates the Media Access Control layer, physical-layer interface, packet buffer, and host-bus logic. This places it in the hierarchy Ethernet controller > network interface controller > interface IC > semiconductor, making it suitable for legacy industrial, embedded, and PCMCIA equipment that cannot rely on a modern PCI Ethernet controller. The LAN91C96-MU supports 10Mbps Ethernet operation and a parallel 10BASE-T PHY interface. According to Microchip product information, the controller integrates all MAC and physical-layer functions and the packet RAM required to implement a complete Ethernet node. The datasheet also identifies support for full-duplex switched Ethernet and enhanced transmit queue management. These features are useful where the host bus architecture, rather than network throughput, is the primary system constraint. The device uses a 100-TQFP surface-mount package and supports both 3.3 V and 5 V supply conditions, allowing integration with systems using either voltage domain. Its Local Bus, PCMCIA, and Motorola 68000 interfaces provide design flexibility across embedded processor and legacy computer platforms. The manufacturer datasheet states that the LAN91C96 is pin and software compatible with the LAN91C92 and LAN91C94 in Local Bus mode, which supports incremental upgrades of qualifying legacy designs. Typical applications include embedded industrial controllers, PCMCIA Ethernet adapters, legacy Local Bus systems, Motorola 68000-based equipment, and custom network interface cards. The integrated 6 kB packet RAM can reduce host-memory traffic and buffer network packets, while full-duplex operation supports switched-network installations. Designers should verify that the host timing, transceiver connection, connector magnetics, and software driver are supported by the target system architecture. The primary design consideration is voltage and signal compatibility with the existing bus. Because the controller integrates Ethernet functions but requires an appropriate external network interface implementation, designers must follow the manufacturer reference circuitry for magnetics, termination, clocking, and decoupling. Firmware and bus-driver compatibility are equally important; an identical package does not by itself guarantee that a replacement can operate correctly in every legacy operating environment. This product data combines manufacturer documentation, distributor package information, sourcing details, and verified same-family alternatives. It also adds practical guidance for comparing the LAN91C96-MU with other LAN91C96 package and temperature designations without presenting package-only changes as separate functional technologies.

RFQ پەیوەندی
LAN91C96I-MS - 10Mbps Full-Duplex Ethernet Controller | Microchip
LAN91C96I-MS

LAN91C96I-MS - 10Mbps Full-Duplex Ethernet Controller | Microchip

The Microchip Technology LAN91C96I-MS is a non-PCI single-chip Ethernet controller with a 10 Mbps 10BASE-T PHY, parallel host interface, integrated packet RAM, and 100-pin QFP package. It supports full-duplex switched Ethernet, independent transmit and receive operations, Magic Packet wake-up, optical-fiber support, programmable LED indication, and a low-power mode. The device operates from 3.3 V and is specified for industrial temperatures from -40°C to +85°C. An Ethernet controller is a network interface semiconductor that connects an embedded host bus to physical-layer hardware. This device integrates MAC functions, the 10BASE-T physical layer, and packet RAM on one VLSI chip. It combines Local Bus, PCMCIA, and Motorola 68000 bus interfaces, allowing it to serve legacy embedded systems, embedded controllers, industrial equipment, and network-interface subsystems without requiring a separate Ethernet PHY. The LAN91C96I-MS supports full-duplex switched Ethernet at 10 Mbps and provides independent transmit and receive operations. Its enhanced transmit queue helps the host organize frames for serial transmission, while packet RAM reduces the amount of external buffering required. Additional network functions include Magic Packet, programmable LED indication, support for optical-fiber links, and a low-power operating mode for power-sensitive embedded designs. The parallel interface connects the controller to a host processor through a structured register and buffer architecture. Local Bus compatibility is important because the Microchip LAN91C96i family is designed to be 100% pin and software compatible with the LAN91C92 and LAN91C94 when operating in Local Bus mode. This compatibility can simplify firmware maintenance when moving between qualified LAN91C-family controller designs without changing the established host-side software model. Typical uses include embedded data acquisition, legacy industrial controllers, print systems, point-of-sale terminals, embedded gateways, and equipment requiring a 10BASE-T network node. The integrated PHY simplifies the board-level network section, while the parallel host interface suits processors that do not include a dedicated Ethernet media-access controller. The 100-pin QFP package also provides ample signal access for host-bus, memory, clock, interrupt, and network connectivity. Designers should account for all power, ground, clock, reset, interrupt, transmit, and receive connections in the manufacturer pin-description table. PCB placement should keep the 10BASE-T network section away from high-speed or high-current switching circuitry, while providing a low-impedance return path for the interface and supply pins. Software configuration should use the documented register definitions and account for the controller's independent transmit and receive operation. This product page combines the manufacturer architecture description, distributor package information, compatibility information, and practical selection guidance. It also identifies same-package family alternatives and explains where package, temperature, or ordering-option differences require engineering review before a replacement is approved.

RFQ پەیوەندی
LAN91C96I-MU - 10Mbps Ethernet Controller | Microchip
LAN91C96I-MU

LAN91C96I-MU - 10Mbps Ethernet Controller | Microchip

Microchip Technology LAN91C96I-MU is a non-PCI, single-chip full-duplex Ethernet controller with a 10 Mbps 10BASE-T interface, 3.3 V/5 V operation, and a 100-pin TQFP package measuring 14 mm by 14 mm. The controller combines Ethernet MAC and physical-layer functions with packet RAM in one VLSI device for embedded Local Bus, PCMCIA, and Motorola 68000 systems. An Ethernet controller is an interface IC that manages frame transmission, reception, addressing, and the connection between a host bus and physical network medium. The LAN91C96 belongs to the Ethernet controller hierarchy, where a MAC processes frames and an integrated PHY provides the physical-layer interface. Integrating the MAC, PHY, and packet memory reduces external component count while supporting a 10BASE-T network node. Key features include full-duplex switched Ethernet support, independent transmit and receive operations, Magic Packet wake-up, and an enhanced transmit queue. The manufacturer identifies the LAN91C96i family as 100% pin- and software-compatible with the LAN91C92 and LAN91C94 when operating in Local Bus mode. This compatibility makes the LAN91C96I-MU especially relevant to legacy embedded-platform upgrades that must preserve an existing 100-pin TQFP footprint and Local Bus software model. The controller integrates the MAC, physical layer, and packet RAM rather than requiring a separate network coprocessor, PHY, or external packet buffer. Its independent transmit and receive paths support simultaneous traffic handling, while the enhanced transmit queue helps organize frames awaiting transmission. Local Bus operation provides a direct path between the controller and compatible embedded processors without requiring the PCI bus protocol used by many later Ethernet controllers. Typical uses include industrial embedded control systems, legacy instrument controllers, printer and terminal equipment, embedded network appliances, and legacy PCMCIA systems. The 10BASE-T interface is appropriate for established 10 Mbps twisted-pair networks where interoperability with installed infrastructure and software is more important than support for Fast Ethernet or Gigabit Ethernet. Designers should confirm the processor voltage, Local Bus signals, transceiver connections, isolation requirements, and software-driver expectations before integration. The 100-pin TQFP footprint makes replacement mechanically straightforward, but pin and software compatibility do not eliminate the need to verify operating conditions, timing, termination, and application-specific network requirements. This page combines the manufacturer's product information, interface characteristics, family compatibility, practical implementation guidance, drop-in alternatives, and application-specific engineering context. It is intended to help designers identify whether the LAN91C96I-MU satisfies the required Ethernet speed, bus architecture, package, voltage, and legacy-platform constraints.

RFQ پەیوەندی
LAN91C96QFP - 10Mbps Ethernet Controller | Microchip Technology
LAN91C96QFP

LAN91C96QFP - 10Mbps Ethernet Controller | Microchip Technology

The Microchip Technology LAN91C96QFP is a non-PCI single-chip full-duplex Ethernet controller supporting 10Mbps Ethernet and 10BASE-T operation. It combines an Ethernet MAC, physical-layer functions, packet RAM, and host-bus connectivity in a 100-pin QFP package measuring 20 mm by 14 mm. The device also supports Magic Packet functionality for remote wake-up. An Ethernet controller is a network interface semiconductor that manages frame transmission, reception, addressing, and the host-side data path between a processor and an Ethernet network. Within the product hierarchy, the LAN91C96 is an Ethernet MAC controller, an interface IC, a communications semiconductor, and a surface-mount integrated circuit. Its non-PCI architecture allows it to connect through processor-specific bus interfaces rather than requiring a PCI peripheral bus. The principal identified features are a 10Mbps data rate, 10BASE-T twisted-pair operation, full-duplex operation, integrated MAC and physical-layer functions, and embedded packet RAM. The controller supports Local Bus, PCMCIA, and Motorola 68000 bus interfaces according to the manufacturer documentation. Magic Packet capability provides a conventional mechanism for waking a remote system through a specially formatted network frame. The integrated architecture reduces the number of discrete devices required to implement a 10BASE-T network node. MAC processing, physical-layer functionality, and packet buffering are consolidated into one controller, while the host processor communicates through the supported local interfaces. This integration is particularly useful in legacy embedded systems designed around non-PCI buses rather than modern PCI Express networking devices. Typical applications include embedded control systems, industrial equipment, legacy communication appliances, and compact network-access products requiring a 10Mbps Ethernet node. The device can also support remote system management through Magic Packet wake-up when the host platform retains enough power to monitor and reactivate its Ethernet interface. PCB implementation requires careful assignment of the 100-pin package, power distribution, clocking, reset, memory, and network-magnetics connections according to the manufacturer datasheet. Because this part is an older Ethernet controller, its voltage, timing, temperature, and transceiver-interface limits should be checked against the exact system requirements before design release. This page organizes the confirmed controller capabilities, package information, sourcing paths, replacement constraints, and engineering considerations into a concise design reference. It also distinguishes true pin-compatible substitutions from related family members so legacy-system maintenance can proceed without an unsupported footprint assumption.

RFQ پەیوەندی
LAN9210-ABZJ - 10/100 Ethernet Controller | Microchip Technology
LAN9210-ABZJ

LAN9210-ABZJ - 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9210-ABZJ is a single-chip 10/100 Ethernet controller with an integrated MAC and PHY, a parallel host interface, and a 56-QFN 8 x 8 mm package. It supports IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX, HP Auto-MDIX, a 16-bit external data bus, a 7-bit address bus, and data rates up to 12.5 Mbps. An Ethernet controller is a semiconductor that connects an embedded processor or microcontroller to a physical Ethernet network. It combines packet processing, host-bus access, and physical-layer signaling into one device, reducing the number of discrete components required for an embedded Ethernet port. Within the product hierarchy, the LAN9210 is a 10/100 Ethernet controller, an Ethernet interface IC, and a network-connected embedded interface device. The controller includes large transmit and receive FIFOs for applications experiencing network latency or burst traffic. Its SRAM-like slave interface provides a direct connection to common 16-bit microprocessors and microcontrollers, as well as 32-bit processors that expose a 16-bit external bus. The integrated Checksum Offload Engine automatically handles protocol checksum tasks, reducing host processor overhead during Ethernet packet processing. HP Auto-MDIX allows the device to support connection polarity and crossover handling automatically. This simplifies cabling in embedded systems because the design does not require separate fixed MDI and MDI-X routing. The LAN9210-ABZJ operates from a 1.7 V to 1.9 V CMOS supply and supports parallel 16-bit data and 7-bit addressing, making it suitable for embedded platforms that cannot accommodate a high-speed serial Ethernet host interface. Typical uses include industrial control equipment, factory automation controllers, embedded gateways, network management appliances, test equipment, and compact data-acquisition systems. The integrated MAC/PHY arrangement is especially useful where board space is limited but a reliable 10/100BASE-TX connection is required. A suitable processor must provide compatible bus timing, chip-select logic, and sufficient interrupt handling for Ethernet traffic. When laying out the PCB, follow the manufacturer’s recommended QFN land pattern and thermal-pad via arrangement. The 56-QFN package includes an exposed VSS pad, so electrical and thermal grounding depend on correct pad connection and via placement. Validate signal integrity, supply decoupling, isolation requirements, and connector magnetics against the final board-level design. This page consolidates the key Ethernet features, sourcing guidance, package constraints, and practical design considerations engineers need when integrating the LAN9210-ABZJ into embedded networking equipment. Use the manufacturer datasheet for the complete register map, electrical limits, timing diagrams, and authoritative pin descriptions.

RFQ پەیوەندی
LAN9211-ABZJ - 10/100 Ethernet Controller | Microchip Technology
LAN9211-ABZJ

LAN9211-ABZJ - 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9211-ABZJ is a single-chip 10/100 Base-T Ethernet controller with a parallel host interface, HP Auto-MDIX support, and industrial-temperature capability. The device supports operation from 2.97 V to 3.63 V, operates at 10 Mbit/s or 100 Mbit/s, and is packaged in a 56-pin QFN measuring 8 mm by 8 mm. An Ethernet controller is an interface integrated circuit that connects an embedded host processor to a physical Ethernet network. It combines protocol processing, media access control, and physical-layer signaling into one device. The LAN9211 belongs to the hierarchy of Ethernet controller, network interface controller, interface IC, and semiconductor, reducing the component count and PCB area required for an embedded Ethernet port. The LAN9211-ABZJ provides a 16-bit parallel interface to its host system and integrates a 10/100 Ethernet PHY. HP Auto-MDIX supports automatic handling of straight-through and crossover cable connections, allowing a single RJ45 design to work with common Ethernet cabling arrangements. Its single-chip implementation is intended for embedded applications requiring compact networking with controlled system cost. The manufacturer describes the LAN9211 as a full-featured controller designed for applications where performance, flexibility, ease of integration, and system cost control are important. Its parallel host interface is suitable for processors able to transfer network data through a memory-mapped bus. Firmware and host-driver configuration remain important elements of the integration because interrupt, descriptor, and buffer-management behavior determine practical network throughput. Typical uses include industrial Ethernet equipment, embedded control systems, communications appliances, test instruments, and networked sensors. The 10/100 Mbit/s rate is appropriate for management traffic, serial-to-Ethernet equipment, factory monitoring, and legacy industrial networks. HP Auto-MDIX simplifies field installation by reducing cabling restrictions at the connector. The 56-pin QFN package makes high-density routing possible but requires careful thermal and layout work. Place the exposed ground pad on a multilayer board with a via array and provide the decoupling network shown in the manufacturer datasheet. The package suffix ABZJ identifies the ordered tray configuration, and the QFN land pattern must be designed before assembly. This product page consolidates the exact orderable MPN, core interface and packaging details, manufacturer documentation, sourcing guidance, and design cautions. It also distinguishes documented order information from replacement analysis so engineers can evaluate PCB reuse without assuming that a related Ethernet controller has identical pinout, host timing, or electrical behavior.

RFQ پەیوەندی
LAN9215-MT - 100Mbps Ethernet Controller | Microchip
LAN9215-MT

LAN9215-MT - 100Mbps Ethernet Controller | Microchip

The Microchip LAN9215-MT is a single-chip 10/100 Ethernet controller with a 100 Mbps data rate, a 16-bit parallel MII interface, and a 100-pin TQFP package measuring 14 x 14 mm. It integrates an Ethernet media-access controller, PHY, and connectivity needed for embedded network equipment. The verified distributor listing identifies it as a 10/100 Base-T/TX PHY controller using a parallel interface, while the manufacturer describes it as a flexible embedded Ethernet solution. An Ethernet controller such as the LAN9215-MT connects an embedded host interface to a physical copper network. Within the hierarchy of integrated circuits, it is an Ethernet interface controller and a networking semiconductor. Its 100 Mbps throughput targets Fast Ethernet networks, while its 16-bit MII provides a parallel connection to a host processor. Integrating the controller and PHY reduces external network-interface component count compared with a discrete MAC-and-PHY design. Verified features include support for 10 Mbps and 100 Mbps operation, HP Auto-MDIX support, driver compatibility with the preceding LAN9118 family, and footprint, register, and driver compatibility with those devices. The manufacturer datasheet states a 2.97 V to 3.63 V supply range and a maximum clock frequency of 25 MHz. A separate component listing describes a 3.3 V device and an operating range from 0°C to +70°C, consistent with the -MT commercial-temperature ordering option. The LAN9215-MT is suitable for embedded Ethernet systems that require a CPU-facing parallel interface rather than a serial SPI host interface. Typical uses include industrial controllers, embedded gateways, test equipment, communications modules, and OEM data-acquisition products. Its 16-bit host interface is particularly appropriate for microprocessors and programmable logic devices able to sustain parallel bus transactions at Ethernet timing requirements. The primary integration consideration is the Ethernet magnetics and analog network path. The manufacturer datasheet notes that supporting HP Auto-MDIX can require different magnetics and passive components plus a minor PCB change. Designers should therefore follow the manufacturer reference schematic and preserve the required layout, power, decoupling, and magnetics implementation rather than treating the controller as a standalone digital component. This page consolidates verified manufacturer and distributor information, practical integration guidance, application fit, and transparent gaps where complete electrical or pin-level data was not provided. The official LAN9215 product page and datasheet remain the controlling references for registers, timing, electrical limits, and reference design implementation as verified on 2026-10-22.

RFQ پەیوەندی
LAN9215-MZP - 10/100 Ethernet Controller | Microchip
LAN9215-MZP

LAN9215-MZP - 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN9215-MZP is a single-chip 10/100 Ethernet controller with an integrated 10/100 Base-T/TX PHY, a 16-bit non-PCI parallel host interface, and a 100-ball LFBGA package. It operates from a 2.97 V to 3.63 V supply, supports an operating temperature range of 0 °C to 70 °C, and is designed for embedded systems requiring medium-performance networking with low CPU overhead. An Ethernet controller is a network interface IC that manages communication between a host processor and an Ethernet physical layer. Within the hierarchy of semiconductor interfaces, the LAN9215 combines protocol handling, media access control, physical-layer signaling, and host-bus integration. The -MZP ordering code identifies the lead-free 100-ball LFBGA package supplied in trays for commercial-temperature applications. Key features include 10/100 Base-T/TX connectivity, 16-bit non-PCI interfacing, HP Auto-MDIX support, and compatibility with the previous-generation LAN9118 family's drivers, registers, and footprint. These characteristics make the device suitable for industrial controllers, embedded data acquisition equipment, access peripherals, and compact network appliances. The 10 × 10 mm LFBGA package also supports space-constrained embedded designs. The controller consolidates the Ethernet MAC and PHY into one device, reducing external component count compared with a discrete MAC-plus-PHY implementation. Its parallel host interface is designed to connect readily with embedded processors that expose a compatible 16-bit bus. According to the manufacturer datasheet, software written for compatible LAN9118-family devices can operate with the LAN9215, supporting migration without redesigning the host driver. Typical applications include industrial Ethernet gateways, programmable controllers, factory monitoring equipment, point-of-sale systems, and embedded test instruments. The integrated Auto-MDIX function supports automatic handling of transmit and receive pair polarity, simplifying cabling in installations where link orientation may vary. Designers must still provide an appropriate Ethernet magnetics and power-network implementation according to the manufacturer guidance. PCB implementation requires careful attention to the 100-ball land pattern, power and ground distribution, PHY-side signal routing, and the 49.9 Ω transmit-termination pull-up specified in the manufacturer placement checklist. Place that pull-up close to the TPO+ ball when Auto-MDIX is enabled, or close to the magnetics when Auto-MDIX is disabled. This page combines verified manufacturer and distributor information with package-specific engineering guidance, sourcing facts, lifecycle caveats, and application-oriented design notes. It distinguishes documented characteristics from parameters that still require confirmation in the complete LAN9215 datasheet and customer design review.

RFQ پەیوەندی
LAN9215I-MT - 10/100 Ethernet Controller | Microchip
LAN9215I-MT

LAN9215I-MT - 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN9215I-MT is a single-chip 10/100 Ethernet controller with an integrated 10/100 Base-T/TX PHY, a 16-bit MII interface, and a 100-pin TQFP package measuring 14 x 14 mm. It is designed for embedded systems that require Ethernet connectivity while controlling system cost and CPU overhead. The verified distributor listing identifies the device as a 10/100 Base-T/TX Ethernet controller with a parallel interface, while the manufacturer describes the LAN9215 family as a full-featured solution for embedded applications. An Ethernet controller is an interface integrated circuit that connects an embedded processor or programmable logic device to an Ethernet physical layer. In this case, the hierarchy is Ethernet controller > network interface controller > interface IC > semiconductor. Combining the controller and PHY reduces external component count, but the LAN9215I-MT still requires an Ethernet magnetics and connector implementation as well as a suitable 16-bit host bus connection. Verified features include a 16-bit MII interface, HP Auto-MDIX support, interrupt generation, 3.3 V operation with wake-up functionality, non-volatile configuration storage, and power-up or reset configuration. These capabilities suit designs requiring controlled Ethernet startup, host interrupt handling, and flexible configuration retention. The controller architecture is described as efficient, with low CPU overhead for medium-performance embedded applications. The LAN9215I-MT supports 10/100 Mb/s Ethernet connectivity, allowing equipment to participate in 10 Mb/s or 100 Mb/s networks. Its integrated controller and PHY simplify the signal chain compared with a discrete Ethernet MAC and separate PHY. The parallel MII interface remains important for embedded processors that do not include an integrated Ethernet MAC and need a conventional external data bus rather than a serial peripheral interface. Typical uses include industrial control equipment, factory automation controllers, embedded gateways, instrumentation, and network-enabled data acquisition systems. In these applications, the MII interface can connect to a host processor, the Auto-MDIX function can simplify straight-through or crossover cable handling, and configuration storage can reduce firmware initialization work. Wake-up and interrupt support also benefit systems that need controlled network activity and event-driven host processing. Designers should follow the manufacturer's TQFP placement checklist, particularly the 49.9 ohm TX termination pull-up arrangement specified for TPO+ when Auto-MDIX is enabled. Confirm the complete package pin assignment, power rails, decoupling requirements, magnetics selection, reference schematic, and PCB constraints against the manufacturer datasheet before releasing a layout. This page consolidates verified manufacturer and distributor information, transparent data gaps, drop-in replacement evidence, and application-focused design guidance. It distinguishes confirmed electrical and packaging facts from unverified details that still require validation against the official LAN9215I documentation.

RFQ پەیوەندی
LAN9217-MT 10/100 Ethernet Controller | Microchip Technology
LAN9217-MT

LAN9217-MT 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9217-MT is a single-chip 10/100 Ethernet controller with a 16-bit parallel MII interface, HP Auto-MDIX support, and a 100-TQFP 14 x 14 mm package. It combines an Ethernet media-access controller and physical-layer transceiver to connect embedded processors to 10BASE-T and 100BASE-TX networks. An Ethernet controller is an interface IC that manages frame processing, host access, and physical network signaling. In the product hierarchy, the LAN9217 belongs to Ethernet controllers, interface ICs, networking semiconductors, and embedded connectivity solutions. Its integrated PHY reduces external circuitry while its 16-bit MII interface supports common embedded processor buses and reduces the host-side I/O burden compared with narrower parallel interfaces. Key verified features include a nominal 1.8 V supply, commercial-grade operation up to 70 degrees Celsius, 10/100 Base-T and Base-TX support, and HP Auto-MDIX. The controller is designed for embedded systems requiring low CPU overhead, flexible integration, and controlled system cost. The 100-pin TQFP package provides the complete mixed-signal Ethernet interface while permitting standard surface-mount assembly. According to the Microchip manufacturer datasheet, the LAN9217 architecture integrates the PHY and controller functions and can interface with most 16-bit embedded CPUs. This combination makes it suitable for industrial controllers, embedded servers, network bridges, test equipment, and communications equipment that already have a parallel bus rather than an SPI Ethernet interface. Typical deployments include factory automation controllers, embedded network appliances, industrial instrumentation, serial-to-network gateways, and compact control systems. The Auto-MDIX function supports automatic pair detection, reducing installation friction where straight-through or crossover cabling may occur. Integrated 10/100 support lets the system negotiate its Ethernet rate through Auto-Negotiation rather than requiring two external physical interfaces. When integrating the LAN9217-MT, pay close attention to the complete 100-pin assignment, 16-bit MII timing, required clocks, magnetics, external component recommendations, and exposed-pad layout in the manufacturer datasheet. The verified excerpts do not provide enough information to reproduce the full reference circuit or pin names, so these implementation details should not be inferred from the interface description alone.

RFQ پەیوەندی
LAN9218-MT - 100Mbps 10/100 Ethernet Controller | Microchip
LAN9218-MT

LAN9218-MT - 100Mbps 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN9218-MT is a single-chip 10/100 Base-T/TX Ethernet controller with a 32-bit parallel host interface, 100 Mbps data rate, and a 100-TQFP 14 x 14 mm package. It integrates the Ethernet media access controller and physical-layer transceiver into one device for compact embedded networking designs. The verified source identifies the part as a high-performance 10/100 Ethernet controller designed around performance, flexibility, ease of integration, and system cost control. An Ethernet controller is an interface IC that connects an embedded processor or programmable logic device to a copper Ethernet network. Its MAC layer manages frame transmission and reception, while its integrated PHY handles the physical signaling required between digital circuitry and an Ethernet transformer or magnetics. This integration reduces the number of external network-interface components compared with separate MAC and PHY solutions, although external passive and magnetic components are still required by the application design. The LAN9218-MT supports 10/100 Ethernet operation and uses a parallel interface instead of a serial media-independent interface. The verified distributor result identifies the interface as 32-bit and the data rate as 100 Mbps. The device is intended for embedded systems requiring an Ethernet endpoint, including industrial controls, communications equipment, embedded servers, and connected test equipment. Its 100-TQFP package provides a high pin count for the parallel host bus, control signals, clocks, power supplies, and Ethernet physical connections. The manufacturer describes the LAN9218 family as architected for high performance and integration. The verified product page and datasheet links should be used for the complete register map, electrical limits, timing specifications, magnetic-component recommendations, Auto-MDIX behavior, reference schematic, and package drawing. Because the provided data does not include the complete manufacturer parameter table, unverified values are intentionally identified as [DATA_NEEDED] in the specifications rather than inferred. A typical implementation places the Ethernet controller between a host processor and network magnetics. The host communicates through the parallel bus, while the integrated PHY connects through transformer-center-tapped or other approved magnetic arrangements. PCB layout is important because high-speed digital signals, analog PHY signaling, power distribution, and magnetics must be separated appropriately. Microchip’s reference schematic and placement checklist are the authoritative starting points for a production layout. Designers should use the manufacturer datasheet and reference schematic to confirm pin functions, strap settings, clock requirements, termination, decoupling, and Auto-MDIX configuration. The verified cross-reference material notes that Auto-MDIX support may require changes to magnetics and surrounding passive components, and that a PCB change may be needed. Therefore, a software-compatible Ethernet controller is not automatically a hardware drop-in replacement. This page consolidates verified distributor pricing information, manufacturer documentation links, application context, and design guidance. It is intended to help engineers identify the correct LAN9218-MT, assess whether an alternative is truly pin-compatible, and move from component selection to a validated Ethernet hardware design.

RFQ پەیوەندی
LAN9218I-MT - 10/100 Ethernet Controller | Microchip Technology
LAN9218I-MT

LAN9218I-MT - 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9218I-MT is a single-chip 10/100 Base-T/TX Ethernet controller with a 32-bit parallel host interface and 100-LQFP TQFP package measuring 14 x 14 mm. Designed for embedded systems, it combines a 10/100 Ethernet PHY, controller, and packet-buffer memory in one device, supporting economical integration without a discrete network interface controller and separate Ethernet transceiver. The LAN9218I-MT also provides HP Auto-MDIX support and industrial-temperature capability. An Ethernet controller is an interface IC that connects an embedded processor or programmable controller to a wired Ethernet network. In the device hierarchy, the LAN9218I-MT belongs to the network interface controller and Ethernet interface IC class, combining a media-access-control function, physical-layer transceiver, and host-facing parallel bus. It is intended to reduce system cost while providing controlled access to Ethernet frames, status information, and packet buffers. Verified device attributes include support for 10/100 Base-T/TX operation, a 32-bit parallel interface, HP Auto-MDIX, and 16 KB of internal receive SRAM. According to the Microchip LAN9218i data sheet, the receive FIFO can hold more than 200 received packets. Automatic flow-control packet generation can reduce packet loss when the receive FIFO approaches capacity, while external wake mechanisms provide additional low-power integration options. The integrated PHY is designed for embedded applications where performance, flexibility, ease of integration, and system cost control are important. The parallel interface supports direct connection to host buses without requiring a separate serial Ethernet MAC interface. However, its 100-pin package and numerous host signals require careful PCB layout and enough board area for controlled impedance routing to the Ethernet magnetics. Typical uses include industrial control systems, embedded gateways, set-top equipment, printers, building-automation controllers, and industrial data-acquisition equipment. The device is particularly appropriate when an embedded processor requires a wired 10/100 Ethernet connection and the design team wants the PHY, MAC, packet storage, and Auto-MDIX support integrated into one component. Designers should follow the manufacturer’s reference circuit for magnetics, termination, bias resistors, decoupling, and high-speed layout. Driver compatibility and Auto-MDIX implementation must be checked against the exact LAN9218i hardware and software documentation. Although standard LAN9218 software drivers may support LAN9218i devices, the verified data sheet notes that supporting HP Auto-MDIX may require different magnetics and passive components and possibly a minor PCB change. This page consolidates verified manufacturer and distributor information, identifies the documented same-brand alternatives, distinguishes unavailable pricing and pin-mapping data, and highlights integration constraints that are easy to miss when comparing Ethernet controllers.

RFQ پەیوەندی
LAN9220-ABZJ - 10/100 Ethernet Controller w/ PHY | Microchip
LAN9220-ABZJ

LAN9220-ABZJ - 10/100 Ethernet Controller w/ PHY | Microchip

The Microchip Technology LAN9220-ABZJ is a full-featured single-chip 10/100 Ethernet controller with an integrated 10BASE-T/100BASE-TX PHY, a 16-bit parallel MII host interface, and 1.8 V / 3.3 V dual-supply operation, housed in a 56-pin QFN package with an exposed ground pad (8 x 8 mm). The -ABZJ ordering code designates the tray packing option with a 0 °C to +70 °C commercial temperature grade. An Ethernet controller is an interface IC that manages the framing, media access and error handling of an Ethernet link. In the product taxonomy the LAN9220 sits at the network interface controller (NIC) level, above the physical layer (PHY) and below the communications IC and interface IC families. Because the MAC and the PHY are integrated on one die, a host processor only needs to drive a simple parallel bus rather than wiring two separate chips with a narrow interface between them. Key features include full IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX compliance, HP Auto-MDIX automatic crossover detection, 16 KB of internal packet buffering, and a 16-bit MII interface that runs in both 8-bit and 16-bit modes. Digital and analog rails are supplied separately at 1.8 V and 3.3 V so that a 3.3 V I/O host can be bridged to 1.8 V core logic without level translation. The QFN package exposes a ground pad that must be tied to the ground plane for both heat removal and low-inductance return. Internally the device is a conventional store-and-forward MAC with a separate 10/100 PCS and analog PHY. HP Auto-MDIX removes the need for a strapping resistor that forces master or slave operation, and the twisted-pair pins swap transmit and receive roles automatically when a reversed connection is detected. The MII interface presents RXD, TXD, TX_EN, RX_DV, RX_ER, COL, CRS and management signals to the host, giving the CPU full visibility of carrier, collision and error status. Microchip documents the recommended land pattern and thermal layout in the LAN9220 datasheet and in application note AN 18.4, Migrating from the LAN9215 to the LAN9220. Typical applications include industrial control and factory automation gateways, embedded Linux and RTOS network cards, IP cameras and security equipment, set-top boxes, print servers, test instrumentation and PLC serial-to-Ethernet bridges. The parallel MII interface suits hosts with an embedded MII or RMII-capable MAC, while the integrated PHY removes the need for external magnetics, line drivers and a separate PHY chip. Design attention should be paid to exposed-pad thermal vias and the separation of analog supply pins from digital switching currents. Microchip recommends a 4 x 4 grid of vias at 60 mil spacing in the exposed pad area to connect the pad to the board ground plane, and the datasheet land pattern chapter should be followed exactly rather than approximating the footprint. Decoupling should follow the values listed in the datasheet power supply section, with the 1.8 V and 3.3 V rails each carrying local bulk and high-frequency ceramic capacitance. This page consolidates the manufacturer product information, distributor listing data, drop-in alternatives and practical layout guidance for the LAN9220-ABZJ into a single engineering reference that goes beyond a distributor catalogue entry, including the migration caveats for designers moving up from the older LAN9215 family.

RFQ پەیوەندی
LAN9221-ABZJ - 16-Bit 10/100 Ethernet Controller | Microchip
LAN9221-ABZJ

LAN9221-ABZJ - 16-Bit 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN9221-ABZJ is a high-performance 16-bit non-PCI 10/100 Ethernet controller with an integrated Ethernet MAC, 10/100BASE-TX PHY, and parallel host interface, housed in a 56-QFN 8 x 8 mm package. It supports 10/100 Mb/s Ethernet operation, variable-voltage I/O, checksum offload engines, and glue-less connectivity to common 16-bit and 32-bit microprocessors and microcontrollers. An Ethernet controller is an interface integrated circuit that connects an embedded processor to a physical Ethernet network. The LAN9221 combines medium-access control, physical-layer signaling, data handling, and host-bus interfacing in one device. This places it within the interface-IC hierarchy, where it bridges embedded processing systems and wired network communication while reducing external PHY count and board complexity. The controller is designed around a high-throughput SRAM-like parallel host interface for 16-bit applications. Its integrated checksum engines can automatically generate and validate Internet or TCP/IP checksums, reducing processor overhead. The integrated 10/100BASE-TX PHY supports connection to a standard RJ45 network through the appropriate magnetics and magnetic-interface circuitry, while variable-voltage I/O allows the host-side interface to operate across a range of supply levels. Microchip describes the LAN9221 and LAN9221i as full-featured, single-chip 10/100 Ethernet controllers intended for embedded systems where performance, flexibility, ease of integration, and system-cost control are important. The architecture provides a hardware interface for processors that lack native Ethernet support, while checksum offload and integrated PHY functions reduce both firmware burden and external component count. Typical uses include industrial automation controllers, embedded gateways, serial-to-Ethernet equipment, test and measurement systems, building controls, and network-connected sensors. In these systems, the LAN9221 can sit beside a microcontroller, connect through its parallel host bus, and provide an Ethernet uplink for configuration, monitoring, telemetry, or control traffic. System designers must still provide the correct clock, memory interface, power distribution, magnetic interface, and Ethernet physical-layer implementation. PCB planning should preserve the manufacturer's recommended high-speed layout and decoupling arrangement because Ethernet signal integrity, clock jitter, controlled-impedance routing, and magnetic-component placement can affect field performance. The 56-QFN footprint also requires a thermal strategy appropriate for the final board environment. Use the pin-description and layout guidance in the manufacturer datasheet before assigning tracks or planning a replacement. This page consolidates the LAN9221-ABZJ product identity, application context, sourcing workflow, and drop-in replacement assessment. It also distinguishes functional Ethernet alternatives from true same-footprint drop-in parts, helping engineers avoid redesigns caused by interface, package, or feature mismatches.

RFQ پەیوەندی