Interface ICs
ژێرپۆلەکان
بەرهەمەکان (5,100+)
LAN8710AI-EZK-TR-ABC - 10/100 Ethernet PHY | Microchip
Microchip LAN8710AI-EZK-TR-ABC is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 32-SQFN 5x5 mm package, variable I/O voltage, and MII or RMII connectivity to an Ethernet MAC. It supports data rates of 10 Mb/s and 100 Mb/s, automatic speed and duplex negotiation, and HP Auto-MDIX for direct or crossover cable connections. An Ethernet PHY is the physical-layer device that converts logical data from an Ethernet MAC into signals that can traverse a copper cable. The PHY sits below the MAC in the Ethernet hierarchy and directly controls the 10BASE-T or 100BASE-TX physical link. The LAN8710AI-EZK-TR-ABC combines this physical-layer function with flexible digital interfacing, automatic link negotiation, and low-power operation in a compact surface-mount package. Key features include support for both 10 Mb/s and 100 Mb/s Ethernet operation, MII and RMII interfaces, variable digital I/O voltage, HP Auto-MDIX, and automatic speed and duplex negotiation. The industrial-temperature option supports operation from -40°C to 85°C, making the device suitable for industrial controls, embedded systems, communications equipment, and connected products that require a compact 10/100 Ethernet interface. The LAN8710AI family uses Microchip flexPWR technology and is designed for space-constrained, power-sensitive applications. Its MII interface provides parallel digital signaling for implementations requiring broader MAC control, while RMII reduces the number of interface signals for designs seeking a smaller, lower-power connection. The manufacturer documentation identifies IEEE 802.3-2005 compliance and both commercial and industrial temperature variants within the family. Typical applications include industrial Ethernet controllers, embedded Linux platforms, factory automation equipment, serial-to-Ethernet systems, network interface cards, set-top equipment, and embedded network interfaces requiring 10/100BASE-TX connectivity. The small 5x5 mm package also supports compact industrial control boards and connected instrumentation where board area is limited. Designers should preserve the manufacturer's recommended power and decoupling networks, provide an appropriate crystal or clock source, and follow the reference layout in the LAN8710A/LAN8710Ai datasheet. The exposed thermal pad requires suitable ground-plane copper and thermal-via treatment. Magnetic isolation between the PHY and Ethernet cable is normally implemented in the external magnetics and RJ45 interface network. This page combines manufacturer specifications, application guidance, practical PCB considerations, and a parameter-focused comparison with same-package alternatives. It is designed to help engineers determine whether the LAN8710AI-EZK-TR-ABC matches the required Ethernet speed, MAC interface, package, temperature range, and industrial design constraints.
LAN8720A-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip
The Microchip Technology LAN8720A-CP-TR-ABC is a single-channel, low-power 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with RMII host connectivity, a 1.6 V to 3.6 V supply range, and a 24-pin SQFN package measuring 4 mm by 4 mm. It operates from 0°C to +85°C and is supplied in tape-and-reel packaging. An Ethernet PHY is the physical-layer interface between a host controller and twisted-pair Ethernet cabling. Within the network hierarchy, the LAN8720A connects an RMII-capable microcontroller, application processor, or dedicated Ethernet controller to a 10/100 network. It implements full-duplex 10BASE-T and 100BASE-TX operation while supporting HP Auto-MDIX, reducing the need to distinguish straight-through and crossover cabling. The device supports standard RMII communication and operates at 10 Mbps or 100 Mbps. Its flexible supply range of 1.6 V to 3.6 V permits integration with 1.8 V, 2.5 V, and 3.3 V systems. The 24-SQFN package provides a compact 4 mm by 4 mm footprint for space-constrained embedded products, while its commercial temperature range covers applications from 0°C to +85°C. Microchip's flexPWR technology is used to reduce power consumption in the LAN8720A family, making the transceiver suitable for connected embedded equipment where energy efficiency is important. The device provides separate digital and analog supply domains, enabling system designers to control supply sequencing and noise isolation according to the manufacturer's application guidance. Typical uses include industrial Ethernet controllers, consumer network equipment, embedded gateways, set-top boxes, printers, IP cameras, and microcontroller-based network nodes. The LAN8720A is especially useful when a host processor already provides an RMII interface and the design needs a compact, low-power 10/100 copper-Ethernet front end. PCB implementation should follow the manufacturer's reference layout for the 24-pin SQFN footprint, exposed pad, magnetics, crystal or clock source, and 50-ohm transmission lines. Care is required with analog and digital supply decoupling, Ethernet transformer isolation, and link-partner startup because those details directly affect EMI, cable compliance, and packet-transfer reliability. This page combines the manufacturer specifications with practical implementation guidance, interface requirements, temperature distinctions, and same-footprint replacement considerations. It is intended to help engineers identify whether the LAN8720A-CP-TR-ABC matches a board's electrical, mechanical, and environmental requirements before layout release or production sourcing.
LAN8720AI-CP - 10/100 RMII Ethernet PHY | Microchip
The Microchip Technology LAN8720AI-CP is a small-footprint 10BASE-T and 100BASE-TX Ethernet transceiver with an RMII interface, auto-negotiation, and HP Auto-MDIX support. It is supplied in a 24-SQFN package measuring 4 mm by 4 mm and is designed for embedded systems requiring 10/100 Ethernet connectivity with a 50 MHz RMII MAC interface. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between digital MAC signals and analog signals carried over twisted-pair cabling. The LAN8720AI-CP occupies the PHY level within the Ethernet hierarchy, working alongside an Ethernet MAC rather than replacing it. Its RMII connection reduces the number of parallel data lines required between the PHY and the host controller. The device supports 10BASE-T and 100BASE-TX operation through automatic speed and duplex negotiation. HP Auto-MDIX allows direct-connect or crossover LAN cables without manual cable selection. It also supports IEEE 802.3-2005 compliant register functions as well as vendor-specific register functions, giving embedded software both standardized and device-specific configuration options. Microchip identifies the LAN8720A and LAN8720Ai as compact solutions with up to 40% lower power consumption than earlier Microchip transceivers. The family integrates a voltage regulator and ESD-protection components to help reduce bill-of-material requirements. The LAN8720AI-CP connects to an Ethernet MAC through a standard RMII interface and supports both 10 Mbps and 100 Mbps operation. Typical uses include industrial Ethernet controllers, embedded Linux systems, programmable logic controllers, factory automation equipment, IoT gateways, and compact network adapters. The small 4 mm by 4 mm package also makes the device suitable for space-constrained boards where a conventional magnetics-heavy Ethernet implementation would be difficult to place. When designing around the LAN8720AI-CP, verify the RMII signal mapping, clock requirements, supply sequencing, magnetics selection, and Ethernet magnetics implementation against the manufacturer datasheet. Layout should keep the digital RMII interface away from the analog magnetics and provide a controlled return path beneath the high-speed differential pairs. Use the manufacturer pin-description table when assigning PCB tracks. This page combines device identity, package details, interface capabilities, replacement guidance, application engineering notes, and side-by-side alternatives. It is intended to help engineers locate the correct datasheet, assess board compatibility, select companion components, and determine whether a proposed replacement is genuinely pin-compatible rather than merely functionally similar.
LAN8720AI-CP-ABC - 10/100 Ethernet PHY | Microchip
The Microchip Technology LAN8720AI-CP-ABC is a compact 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with a standard RMII interface, operating at 10 Mbps or 100 Mbps. It is offered in a 24-SQFN package measuring 4 x 4 mm and supports the industrial temperature range of -40°C to 85°C. The device uses Microchip flexPWR technology and supports HP Auto-MDIX for direct or crossover cable connections. An Ethernet PHY is the physical-layer component that translates digital data from an Ethernet media-access controller into signals that can traverse a twisted-pair network. In the hierarchy of network semiconductors, the PHY operates below the Ethernet MAC and above the transformer, magnetics, connector, and cable. The RMII interface reduces the number of signals required between the PHY and the host controller, making the LAN8720AI-CP-ABC suitable for compact embedded systems with limited connector and routing resources. Key features include full-duplex 10BASE-T and 100BASE-TX operation, automatic speed and duplex negotiation, HP Auto-MDIX support, and operation from 1.8 V, 2.5 V, or 3.3 V supplies. IEEE 802.3-2005-compliant register functions are supported alongside vendor-specific registers. These features allow the PHY to connect to an RMII-based microcontroller or dedicated Ethernet controller without requiring a separate manual speed configuration. The LAN8720AI-CP-ABC integrates the digital transceiver, analog transmit and receive channels, clock recovery, and auto-negotiation functions into one package. Its 24-SQFN footprint supports high-density PCB layouts, while the exposed thermal pad provides a direct heat-transfer path. The interface is designed for host systems operating at 50 MHz RMII reference-clock frequency, which simplifies synchronization with common embedded Ethernet media-access controllers. Typical applications include industrial Ethernet controllers, embedded IoT gateways, factory automation equipment, network-connected sensors, compact embedded Linux systems, and consumer or communications equipment with a 10/100 Ethernet link. The PHY is particularly useful when the design requires wired networking but must limit board area, interface pin count, and power consumption compared with a larger Ethernet transceiver implementation. Layout quality is critical because high-speed digital and analog signals share the same package. Place the PHY close to the Ethernet magnetics and connector, keep the RMII clock and data traces short, provide clean supply decoupling, and follow the manufacturer’s reference layout for the exposed pad and mixed-signal return paths. This page combines package and interface guidance with practical replacement analysis for design reviews and sourcing. The manufacturer identifies the LAN8720A family as active and distinguishes extended-commercial and industrial temperature options. For new designs, confirm the exact ordering code, package, thermal grade, and RMII implementation against the current manufacturer datasheet before releasing production artwork.
LAN8720AI-CP-TR-ABC - 10/100 RMII Ethernet PHY | Microchip
The Microchip LAN8720AI-CP-TR-ABC is a compact 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with Full MII and RMII host interfaces, 24-SQFN lead-free packaging in a 4 x 4 mm footprint, and an industrial temperature range of -40°C to +85°C. The device is designed to connect a microcontroller, processor, or other embedded host to a standard 10/100 Ethernet network. An Ethernet PHY is the physical-layer component that converts digital frame data into differential Ethernet signaling and receives differential network signals for conversion back into digital data. The LAN8720AI belongs to the Ethernet transceiver hierarchy and the broader integrated-circuit category of network interface ICs. Its RMII interface reduces the number of host signals required for 10/100 Ethernet connectivity, while Full MII support provides an alternative host interface for designs using the wider parallel bus. Key features include automatic speed and duplex negotiation, HP Auto-MDIX support, IEEE 802.3-2005 compliant and vendor-specific register functions, and Microchip flexPWR technology. Auto-negotiation automatically establishes the best supported speed and duplex mode. HP Auto-MDIX allows direct-connect or crossover Ethernet cables without a manual crossover switch, simplifying connections to computers, switches, and test equipment. The LAN8720AI family operates from 1.8 V, 2.5 V, or 3.3 V supply levels, allowing integration with both 3.3 V and compatible lower-voltage embedded systems. The industrial-order option supports -40°C to +85°C operation, while the related commercial option supports 0°C to +85°C. The 24-SQFN package includes an exposed thermal pad and is supplied on a 4,000-piece reel for the listed ordering configuration. Typical applications include industrial Ethernet controllers, embedded Linux systems, factory automation equipment, serial-to-Ethernet gateways, IoT gateways, and compact network appliances. In each case, the PHY supplies the physical Ethernet connection while the host controller handles higher-layer networking, packet processing, and application protocols. RMII is especially useful where connector count and PCB area are constrained. Designers should follow the manufacturer datasheet for the complete pin-description table, recommended crystal and decoupling circuits, RMII timing requirements, and exposed-pad land pattern. Validate the PHY and host clocking arrangement, magnetics, termination, and cable path as a complete Ethernet interface rather than evaluating the transceiver independently of its external network components. This page consolidates the manufacturer interface capabilities, package and temperature distinctions, order-code behavior, and practical replacement guidance into an engineering-focused comparison of the LAN8720AI-CP-TR-ABC and compatible Ethernet PHY options.
LAN8740A-EN - 10/100 Ethernet PHY | Microchip Technology
The Microchip Technology LAN8740A-EN is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 32-pin SQFN package measuring 5 mm by 5 mm. It supports MII and RMII host interfaces, operates at 10 Mbps or 100 Mbps, and includes variable I/O voltage, auto-negotiation, HP Auto-MDIX, cable diagnostics, and deterministic loopback delay. An Ethernet PHY is the physical-layer interface between a network media-access controller and twisted-pair cabling. Within the Ethernet interface hierarchy, the PHY connects a digital MAC to the analog 10BASE-T or 100BASE-TX line interface. The LAN8740A supports IEEE 802.3, IEEE 802.3u, and IEEE 802.3az Energy Efficient Ethernet operation, placing it in the low-power 10/100 Ethernet transceiver category. Key features include support for both straight-through and crossover cables through HP Auto-MDIX, automatic speed and duplex-mode selection, variable I/O voltage, and cable diagnostics that can reduce installation and troubleshooting costs. Commercial and industrial temperature variants are offered because the LAN8740A/LAN8740Ai family is specified from 0°C to 70°C or -40°C to 85°C, depending on the selected ordering option. The device is designed for embedded systems requiring a compact 10/100 Ethernet interface rather than gigabit data rates. MII support offers a parallel host interface for designs using the larger pin assignment, while RMII reduces the number of host-side signals and can simplify connections to controllers that support that interface. Auto-negotiation allows the PHY to select the best supported speed and duplex combination with the link partner. Typical uses include industrial controllers, embedded network equipment, set-top and communications appliances, and connected industrial products requiring a compact Ethernet front end. A 5 mm by 5 mm surface-mount package supports compact board layouts, but correct magnetics, termination, reference-clock implementation, decoupling, and high-speed layout remain essential for reliable links. Designers should follow the manufacturer datasheet and its reference circuit for the 25 MHz crystal or oscillator network, magnetic isolation, center-tap capacitors, and PCB layout. The 5 mm by 5 mm package also requires careful thermal assessment when the PHY operates continuously in an enclosed system. This page consolidates manufacturer specifications, distributor availability information, package details, and verified cross-reference evidence into an engineering-oriented guide. It also distinguishes documented functions from parameters that still require confirmation from the complete manufacturer datasheet or a detailed PCB design review.
LAN8740AI-EN - 10/100 Ethernet PHY, RMII/MII, 32-SQFN | Microchip
The Microchip LAN8740AI-EN is a single-port 10/100 Base-T Ethernet physical layer (PHY) transceiver with MII and RMII host interfaces, offered in the 32-pin SQFN (5x5 mm) package and rated for the industrial -40 °C to +85 °C temperature range. The 'AI' suffix denotes the industrial temperature grade, while '-EN' identifies the standard tray/tube ordering code of the LAN8740Ai family. An Ethernet PHY is the physical-layer transceiver that converts parallel digital data from a MAC into differential 10BASE-T or 100BASE-TX signalling on a twisted-pair cable, and converts the incoming analogue signal back into digital words. In the OSI hierarchy a PHY sits below the MAC inside the data-link layer, and the device therefore belongs to the network interface controller family of integrated circuits alongside MAC controllers and USB-to-Ethernet bridges. Key features include auto-negotiation for automatic speed and duplex selection, HP Auto-MDIX for direct-connect or crossover cable use without manual crossover wiring, auto-polarity correction, deterministic loopback delay for real-time system performance, and cable diagnostics that reduce installation and service cost. The device is compliant with IEEE 802.3 and IEEE 802.3u and is well suited to consumer, embedded and industrial equipment. The LAN8740Ai also carries Microchip's flexPWR technology, an integrated low-power design approach that removes the need for an external switching regulator for the PHY core. This reduces board area, component count and overall system power, which is decisive in battery-backed and Energy Efficient Ethernet designs where the PHY is frequently the largest standby consumer on the board. Typical uses include industrial Ethernet gateways, PLC and HMI panels, IP cameras and NVRs, set-top boxes and consumer set-top equipment, printer and copier controllers, embedded Linux boards using an RMII-capable SoC, and network-connected sensors and IoT nodes. The small 5x5 mm footprint keeps the PHY compact enough for space-constrained embedded boards while the 32-pin SQFN keeps the pin count manageable for four-layer PCB design. The main design trade-off is interface choice: RMII reduces the host pin count to a minimum and therefore lowers EMI and cost, but it is sensitive to clock timing and requires a stable 50 MHz reference, whereas full MII offers a parallel, more forgiving bus at the expense of roughly thirty signal pins. Commercial designs should confirm RMII clock, reference and crystal/oscillator requirements against the manufacturer datasheet before layout is frozen. This page consolidates the manufacturer device documentation, verified distributor listings, drop-in alternatives and practical PCB and layout guidance into a single design reference, so that schematic and layout decisions for a LAN8740Ai-based Ethernet port can be made without assembling the same information from many sources.
LAN8741AI-EN - 10/100 Ethernet PHY | Microchip Technology
Microchip Technology LAN8741AI-EN is a 10/100 Base-T/TX Fast Ethernet physical-layer transceiver with a Full MII or RMII MAC interface, operating at 10 Mbps or 100 Mbps. The device is housed in a 32-SQFN package measuring 5 mm by 5 mm and supports industrial-temperature operation from -40°C to 85°C. Its primary interfaces are MII, RMII, 10BASE-T, and 100BASE-TX. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between digital MAC signals and analog signals carried over twisted-pair cabling. Within the network hierarchy, LAN8741AI-EN belongs to the Ethernet interface IC category and implements the physical layer required by a 10/100 Fast Ethernet MAC. It adds negotiated speed and duplex selection, HP Auto-MDIX cable handling, Energy Efficient Ethernet support, and power-saving sleep functions to the basic physical-layer function. The LAN8741AI-EN supports IEEE 802.3az Energy Efficient Ethernet, full-duplex 10BASE-T and 100BASE-TX links, automatic speed and duplex negotiation, and HP Auto-MDIX. HP Auto-MDIX allows a direct-connect or crossover cable to be used without manually reconfiguring the PHY. The manufacturer also identifies deterministic loopback delay as a feature for real-time system performance, making the device relevant to deterministic embedded networking designs. Communication with the Ethernet MAC is performed through standard MII or RMII interfaces. IEEE 802.3u-compatible MII operation provides a parallel digital interface, while RMII reduces the number of required signals. The interface choice allows the PHY to be paired with an embedded controller, microcontroller, application processor, or other MAC-capable host according to the system clocking and signal-count requirements. Typical uses include industrial control equipment, embedded Ethernet gateways, factory automation nodes, building automation controllers, network-connected sensors, and compact communication modules. The industrial temperature range supports designs expected to operate across extended commercial environments, although system designers must also verify thermal, isolation, magnetics, and regulatory requirements for their installation environment. PCB implementation should account for the 5 mm by 5 mm SQFN footprint, exposed-pad thermal management, short high-speed traces, controlled return paths, and the external magnetics required by the Ethernet physical layer. Keep the digital MAC interface separated as far as practical from the analog network-side circuitry, and use the manufacturer’s reference layout and component guidance to preserve signal integrity and reliable auto-negotiation. This product page organizes the LAN8741AI-EN’s interface capabilities, package information, operating ranges, available drop-in alternative, application guidance, and design considerations. It also identifies the engineering details that require confirmation against the manufacturer datasheet, particularly pin assignments and detailed electrical limits.
LAN8742-CZ - 100Mbps Ethernet PHY with 24-QFN
The Microchip Technology LAN8742-CZ is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 100 Mbps maximum link rate, variable I/O voltage, and a 24-pin QFN package. It supports the IEEE 802.3 and IEEE 802.3u standards and is designed to connect an Ethernet MAC through an RMII interface to copper twisted-pair Ethernet magnetics. The verified search data identifies it as an Ethernet controller interface device and a 1/1 driver-receiver configuration with full-duplex RMII support. An Ethernet PHY is the physical-layer device that translates digital MAC data into electrical signaling for a network cable and converts received cable signals back into digital data. In the hierarchy, the LAN8742-CZ belongs to the Ethernet transceiver, network-interface, integrated-interface-IC, and broader semiconductor categories. Placing a PHY between a host controller and an RJ45 magnetics assembly allows a microcontroller, application processor, or dedicated Ethernet controller to connect to 10 Mbps or 100 Mbps copper networks without implementing the analog cable interface directly. Verified features include 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, Energy Efficient Ethernet support identified in the family description, and Wake-On-LAN functionality identified for the LAN8742 family. The variable I/O voltage allows the digital interface voltage to be selected for integration with a host, while the compact 24-QFN, 4 x 4 mm package supports space-constrained embedded designs. The verified results also describe cable diagnostics support, although detailed diagnostic limits are not supplied. The LAN8742-CZ is normally used as the PHY beside a 10/100 Ethernet magnetic module and RJ45 connector. RMII connects the PHY to the MAC, reducing the number of parallel data and control signals compared with older MII implementations. The PHY supports 10 Mbps and 100 Mbps operation and automatically negotiates the best supported speed and duplex mode, simplifying host-side configuration. Exact timing, current, voltage-range, temperature, and package-dimension details require the manufacturer datasheet and are not inferred here. For new production designs, verify lifecycle status and sourcing before committing to an obsolete device. The verified cross-reference data specifically identifies LAN8742A-CZ-TR as a compatible substitute with extended availability, while also describing LAN8742AI-CZ-TR as a direct pin-compatible replacement. Any substitution should be checked against the exact RMII pin mapping, voltage domains, package exposed-pad requirements, magnetic-device pinout, and system timing. This page combines verified distributor and manufacturer information with application guidance, replacement context, and package-focused design notes. It does not invent unpublished pricing, electrical limits, pin names, or lifecycle dates; unavailable values are explicitly marked for engineering review.
LAN8742-CZ-TR - 100Mbps Ethernet PHY with 24-QFN (Tape & Reel)
The Microchip Technology LAN8742-CZ-TR is a low-power 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 100 Mbps maximum link rate, variable I/O voltage, and a 24-pin QFN package. It supports the IEEE 802.3 and IEEE 802.3u standards and is designed to connect an Ethernet MAC through an RMII interface to copper twisted-pair Ethernet magnetics. The verified search data identifies it as an Ethernet controller interface device and a 1/1 driver-receiver configuration with full-duplex RMII support. An Ethernet PHY is the physical-layer device that translates digital MAC data into electrical signaling for a network cable and converts received cable signals back into digital data. In the hierarchy, the LAN8742-CZ-TR belongs to the Ethernet transceiver, network-interface, integrated-interface-IC, and broader semiconductor categories. Placing a PHY between a host controller and an RJ45 magnetics assembly allows a microcontroller, application processor, or dedicated Ethernet controller to connect to 10 Mbps or 100 Mbps copper networks without implementing the analog cable interface directly. Verified features include 10BASE-T and 100BASE-TX operation, auto-negotiation, HP Auto-MDIX, Energy Efficient Ethernet support identified in the family description, and Wake-On-LAN functionality identified for the LAN8742 family. The variable I/O voltage allows the digital interface voltage to be selected for integration with a host, while the compact 24-QFN, 4 x 4 mm package supports space-constrained embedded designs. The verified results also describe cable diagnostics support, although detailed diagnostic limits are not supplied. The LAN8742-CZ-TR is normally used as the PHY beside a 10/100 Ethernet magnetic module and RJ45 connector. RMII connects the PHY to the MAC, reducing the number of parallel data and control signals compared with older MII implementations. The PHY supports 10 Mbps and 100 Mbps operation and automatically negotiates the best supported speed and duplex mode, simplifying host-side configuration. Exact timing, current, voltage-range, temperature, and package-dimension details require the manufacturer datasheet and are not inferred here. For new production designs, verify lifecycle status and sourcing before committing to an obsolete device. The verified cross-reference data specifically identifies LAN8742A-CZ-TR as a compatible substitute with extended availability, while also describing LAN8742AI-CZ-TR as a direct pin-compatible replacement. Any substitution should be checked against the exact RMII pin mapping, voltage domains, package exposed-pad requirements, magnetic-device pinout, and system timing. This page combines verified distributor and manufacturer information with application guidance, replacement context, and package-focused design notes. It does not invent unpublished pricing, electrical limits, pin names, or lifecycle dates; unavailable values are explicitly marked for engineering review.
LAN8742A-CZ - 10/100 Ethernet PHY, RMII, 24-SQFN | Microchip (Tape & Reel)
The Microchip LAN8742A-CZ is a low-power 10BASE-T/100BASE-TX Ethernet PHY transceiver with variable I/O voltage, packaged in a 24-pin SQFN (4x4 mm) and supplied on tape and reel. It supports MII and RMII MAC interfaces, operates from a 1.8V to 3.3V variable I/O supply, and is IEEE 802.3 / 802.3u compliant. The device integrates auto-negotiation, auto-polarity correction, and HP Auto-MDIX, eliminating the need for crossover cables. It is well-suited for consumer, embedded, and industrial Ethernet applications. A PHY (physical layer transceiver) is a key element of any Ethernet link: it sits between the MAC controller and the magnetic transformer/RJ-45, handling line encoding/decoding, link training, and electrical signaling over twisted-pair copper. PHY transceivers are part of the broader category of Ethernet interface ICs, which include MAC controllers, switches, and integrated MAC+PHY SoCs. The LAN8742A specifically implements the 10/100 Mbps copper PHY only; higher-speed Gigabit (1000BASE-T) PHYs use multi-level signaling (PAM) and more pins. Key features of the LAN8742A-CZ include Wake-On-LAN support for system-level sleep modes, cable diagnostics for fault detection, and flexPWR flexible power technology for low-power operation. The variable I/O voltage (1.8V-3.3V) allows direct connection to low-voltage MCUs without level shifters. The HP Auto-MDIX feature automatically detects and compensates for TX/RX pair swaps, allowing either straight-through or crossover cables to be used interchangeably. Architecturally, the LAN8742A employs DSP-based echo and crosstalk cancellation to achieve robust 100BASE-TX performance over Cat5 cable. The on-chip PHY includes an integrated termination network and uses energy detect plus power-down modes to meet modern standby-power requirements. MII and RMII MAC interfaces are selectable via strap pins, allowing the same part to be paired with virtually any MCU or SoC MAC. Typical applications include IoT gateways, industrial Ethernet nodes, embedded web servers, building automation controllers, IP cameras, and consumer electronics requiring a wired network connection. The wide 1.8V-3.3V I/O range and low power consumption also make it attractive for battery-powered Ethernet-enabled devices. When designing with the LAN8742A-CZ, follow the Microchip LAN8742 QFN Routing Checklist for proper PCB layout - the analog ground plane and 50-ohm impedance-controlled differential pairs are critical for radiated emissions and signal integrity compliance. Decoupling capacitors must be placed adjacent to each power pin, and the magnetics must be specified to IEEE 802.3 isolation and return-loss specifications. This page synthesizes distributor pricing, drop-in same-BLAN alternatives, and Microchip application-note design notes not found in the manufacturer datasheet alone - giving engineers a single, decision-ready reference.
LAN8742A-CZ-TR - 10/100 Ethernet PHY, RMII, 24-SQFN | Microchip
The Microchip LAN8742A-CZ-TR is a low-power 10BASE-T/100BASE-TX Ethernet PHY transceiver with variable I/O voltage, packaged in a 24-pin SQFN (4x4 mm) and supplied on tape and reel. It supports MII and RMII MAC interfaces, operates from a 1.8V to 3.3V variable I/O supply, and is IEEE 802.3 / 802.3u compliant. The device integrates auto-negotiation, auto-polarity correction, and HP Auto-MDIX, eliminating the need for crossover cables. It is well-suited for consumer, embedded, and industrial Ethernet applications. A PHY (physical layer transceiver) is a key element of any Ethernet link: it sits between the MAC controller and the magnetic transformer/RJ-45, handling line encoding/decoding, link training, and electrical signaling over twisted-pair copper. PHY transceivers are part of the broader category of Ethernet interface ICs, which include MAC controllers, switches, and integrated MAC+PHY SoCs. The LAN8742A specifically implements the 10/100 Mbps copper PHY only; higher-speed Gigabit (1000BASE-T) PHYs use multi-level signaling (PAM) and more pins. Key features of the LAN8742A-CZ-TR include Wake-On-LAN support for system-level sleep modes, cable diagnostics for fault detection, and flexPWR flexible power technology for low-power operation. The variable I/O voltage (1.8V-3.3V) allows direct connection to low-voltage MCUs without level shifters. The HP Auto-MDIX feature automatically detects and compensates for TX/RX pair swaps, allowing either straight-through or crossover cables to be used interchangeably. Architecturally, the LAN8742A employs DSP-based echo and crosstalk cancellation to achieve robust 100BASE-TX performance over Cat5 cable. The on-chip PHY includes an integrated termination network and uses energy detect plus power-down modes to meet modern standby-power requirements. MII and RMII MAC interfaces are selectable via strap pins, allowing the same part to be paired with virtually any MCU or SoC MAC. Typical applications include IoT gateways, industrial Ethernet nodes, embedded web servers, building automation controllers, IP cameras, and consumer electronics requiring a wired network connection. The wide 1.8V-3.3V I/O range and low power consumption also make it attractive for battery-powered Ethernet-enabled devices. When designing with the LAN8742A-CZ-TR, follow the Microchip LAN8742 QFN Routing Checklist for proper PCB layout - the analog ground plane and 50-ohm impedance-controlled differential pairs are critical for radiated emissions and signal integrity compliance. Decoupling capacitors must be placed adjacent to each power pin, and the magnetics must be specified to IEEE 802.3 isolation and return-loss specifications. This page synthesizes distributor pricing, drop-in same-BLAN alternatives, and Microchip application-note design notes not found in the manufacturer datasheet alone - giving engineers a single, decision-ready reference.
LAN8742AI-CZ - 10/100 Ethernet PHY | Microchip Technology
The Microchip Technology LAN8742AI-CZ is a small-footprint RMII 10/100 Fast Ethernet transceiver with HP Auto-MDIX, cable diagnostics, Wake-on-LAN functionality, and flexPWR technology in a 24-SQFN package. It is designed for consumer, embedded, and industrial Ethernet equipment requiring a compact single-port Ethernet physical layer solution. The device supports 10BASE-T and 100BASE-TX operation, auto-negotiation, auto-polarity correction, and direct or crossover cable connections through HP Auto-MDIX. An Ethernet PHY, also called a physical-layer transceiver, converts digital data into electrical signals for transmission over twisted-pair cabling and converts received signals into data for the host controller. The LAN8742AI-CZ sits between an Ethernet transformer or magnetics and an RMII-compatible embedded host. In the hierarchy of network interfaces, it is a physical-layer IC within the Ethernet transceiver and interface-controller category. The LAN8742AI-CZ offers a 1.8 V to 3.3 V operating range, as identified for this part in the supplier listing. Its integrated low-power features and Wake-on-LAN capability suit systems that need to reduce activity during idle periods. Auto-negotiation automatically establishes the best supported speed and duplex mode, while auto-polarity correction prevents incorrect operation when cable polarity is reversed. HP Auto-MDIX removes the requirement to distinguish straight-through and crossover cables at the connector. The LAN8742AI-CZ is also described as supporting cable diagnostics, which can help embedded equipment identify wiring faults during installation or field maintenance. Its small 4 x 4 mm SQFN package supports compact PCB layouts, but the exposed pad and high-speed interface require careful thermal, grounding, and signal-integrity implementation. Microchip provides a dedicated LAN8742 QFN routing checklist that specifies connecting the exposed digital-ground pad to an internal ground plane with a 2 x 2 grid of four power vias. Typical applications include industrial Ethernet controllers, embedded Linux systems, network appliances, consumer electronics, USB-to-Ethernet equipment, and IoT gateways. The RMII interface is particularly appropriate for microcontrollers and application processors that provide a parallel Ethernet MAC interface. Selection should consider magnetics compatibility, firmware driver support, cable-diagnostic behavior, operating-temperature requirements, and the precise board-level implementation guidance. For reliable operation, follow the manufacturer datasheet for pin assignments, external component values, crystal or clock requirements, and layout clearances. Treat the exposed pad as a thermal and electrical connection rather than an unused lead. Validate the completed board for RMII timing, Ethernet magnetics integration, return-loss performance, radiated emissions, and cable insertion before production. This page combines the manufacturer part information, supplier listings, package details, interface capabilities, drop-in family options, and practical PCB guidance into a focused engineering reference. It also distinguishes confirmed electrical characteristics from parameters that still require the manufacturer datasheet for final design verification.
LAN9115-MT - 10/100 Ethernet Controller, 3.3V | Microchip
The Microchip Technology LAN9115-MT is a single-chip 10/100 Ethernet controller with a nominal 3.3 V supply, clock frequency up to 25 MHz, and a 100-pin TQFP package measuring 14 x 20 mm. It integrates an Ethernet controller and Base-T/TX PHY behind a 16-bit parallel interface for embedded systems requiring medium-performance network connectivity. The device is positioned as a cost-conscious, flexible Ethernet solution that reduces the component count compared with separate controller and physical-layer devices. An Ethernet controller is an interface IC that connects an embedded processor or programmable logic device to a physical Ethernet network. The controller manages higher-level station functions, while the integrated PHY handles the physical signaling required for 10BASE-T and 100BASE-TX links. Within the semiconductor hierarchy, this device is a network interface controller, a communications interface IC, and a system-level Ethernet connectivity component. Verified product information identifies the LAN9115 as a full-featured single-chip 10/100 Ethernet controller intended for 16-bit embedded applications. Its parallel interface supports integration with processors that use a memory-mapped bus rather than a dedicated PCI interface. The supplied distributor classification also identifies a Base-T/TX PHY, while the product description emphasizes price-performance balance for medium-performance requirements. The LAN9115 combines MAC-oriented controller functionality and physical-layer connectivity in one package. This consolidation can simplify PCB routing and reduce the number of external interface components, but the Ethernet magnetics, connector, termination, clock source, decoupling network, and firmware support remain essential parts of a working network subsystem. Its 3.3 V operation also places it in the supply domain of many embedded processors, FPGAs, and industrial controllers. Typical uses include industrial control equipment, embedded gateways, factory data acquisition, instrumentation, building automation, serial-to-Ethernet products, and compact embedded servers. The LAN9115 is most appropriate where 10/100 Ethernet is sufficient and a 16-bit host interface is preferable to a PCI-based architecture. It can also form the network foundation for supervisory systems that exchange configuration, status, and diagnostic data. Board design should reserve careful attention to the 25 MHz clock requirement, 3.3 V power distribution, PHY-to-magnetics routing, and manufacturer-recommended decoupling and layout practices. Because the verified snippets do not provide a complete timing, register, electrical-limit, or absolute-maximum specification set, designers should consult the official manufacturer datasheet before finalizing clock tolerances, impedance, magnetics selection, or software configuration. This page consolidates verified product identity, package, interface, supply, and sourcing information into a practical selection record. It also distinguishes verified facts from unavailable details rather than guessing, while directing engineers to the official datasheet and authorized distributor listings for design validation and current commercial availability.
LAN9116-MT - 10/100 Ethernet Controller | Microchip
Microchip LAN9116-MT is a single-chip 10/100 Ethernet controller with a parallel CPU interface for embedded systems requiring integrated network connectivity, flexible integration, and controlled system cost. It supports 10 Mbps and 100 Mbps Ethernet operation and interfaces with 16-bit or 32-bit embedded processors. The device is supplied in a 100-pin TQFP package measuring 14 x 20 mm. Its combination of an Ethernet controller, 10/100 Base-T/TX physical-layer interface, parallel host interface, and low host-CPU overhead makes it suitable for industrial controllers, embedded gateways, network management equipment, and compact connected products. An Ethernet controller is an interface IC that connects a processor or embedded system to an Ethernet network. In the hardware hierarchy, a network interface controller includes the Ethernet MAC, host-facing bus interface, and physical-layer functions required for copper Ethernet communication. The LAN9116 family combines these functions in one device, reducing the number of external interface components needed when an embedded product requires 10/100 Ethernet rather than only a lower-level transceiver. According to the Microchip LAN9116 datasheet, the controller is intended for embedded applications where performance, flexibility, integration ease, and system cost control are important. Its architecture targets 32-bit applications with medium-to-high performance requirements, while the parallel interface also supports connection to many 16-bit embedded processors. The documented 10/100 Base-T/TX capability allows a system to negotiate 10 Mbps or 100 Mbps operation, while the integrated controller architecture reduces the processing burden imposed on the host CPU. The LAN9116-MT belongs to the LAN9116 product family and is offered as a 100-pin TQFP implementation. Its parallel host interface is intended to connect with embedded processor buses rather than using the serial interfaces associated with many newer Ethernet controllers. This makes it relevant to established embedded processor platforms where a proven parallel bus, compact 14 x 20 mm package, and integrated 10/100 Ethernet function can simplify a board-level design without requiring a separate PHY. Typical applications include industrial Ethernet gateways, programmable controllers, factory automation equipment, embedded routers, print servers, set-top boxes, and network-enabled test equipment. The device is also appropriate for compact industrial control systems in which a 16-bit or 32-bit host processor needs deterministic access to Ethernet packet data. Designers should evaluate host-bus timing, magnetics selection, connector integration, and reference-circuit layout against the complete manufacturer datasheet before releasing production hardware. The primary design consideration is that the LAN9116-MT integrates substantial networking functionality around a parallel host interface. Designers should use the manufacturer reference schematic and placement checklist as the basis for routing the processor interface, supplying the required clock and reset circuitry, and placing magnetics close to the physical-layer section. Input and output constraints, crystal requirements, termination, and decoupling must be verified directly from the manufacturer datasheet rather than inferred from the distributor description. This page consolidates the verified manufacturer description, distributor package information, family comparisons, and practical selection guidance for LAN9116-MT. It also identifies where verified drop-in alternatives are not established, helping engineers distinguish documented family alternatives from unverified claims while reducing design, sourcing, and integration risk.
LAN9117-MD - 10/100 Ethernet Controller | Microchip
The Microchip LAN9117-MD is a high-performance, single-chip 10/100 non-PCI Ethernet controller designed for embedded systems, with a 16-bit CPU interface and integrated Ethernet controller functionality. The verified product information identifies it as a member of the LAN9118 family and emphasizes efficient interfacing with most 16-bit embedded CPUs, low CPU overhead, and suitability for medium- to high-performance applications. It is packaged as an Ethernet interface controller from the LAN9117 family; the exact package designation, pin count, voltage ratings, and full electrical limits require confirmation from the manufacturer datasheet. What is an Ethernet controller? An Ethernet controller is an integrated circuit that manages the hardware and protocol functions required for a host system to communicate over an Ethernet network. In the LAN9117-MD, the 10/100 designation refers to support for 10 Mb/s and 100 Mb/s Ethernet operation, while the non-PCI description identifies its host-side integration approach. The device is intended to reduce CPU involvement in network traffic and simplify embedded Ethernet connectivity. The most important verified feature is the 16-bit host-interface orientation. The product data states that the LAN9117 efficiently interfaces with most 16-bit embedded CPUs and uses a low-CPU-overhead architecture. It also belongs to the LAN9118 family, which provides useful context for firmware and hardware design work involving related SMSC Ethernet controllers. The product is marketed for embedded applications where performance, flexibility, ease of integration, and system-cost control are priorities. LAN9117-MD is suitable for industrial control, embedded instrumentation, network-connected test equipment, and compact embedded platforms that need 10/100 Ethernet without a PCI bus. Compared with a software-heavy network interface, a dedicated Ethernet controller can offload protocol and hardware tasks, reducing the burden placed on the host processor. The actual throughput, media interface, clock requirements, supply voltage, and electrical timing must be checked against the official datasheet before schematic capture. A key design consideration is confirming the exact package footprint and pin compatibility before substituting any part. The available migration guidance explicitly states that the LAN9211 is not a drop-in replacement for the LAN9117 because it uses a different package and requires a new PCB. This distinction is important when comparing Ethernet controllers by function rather than by mechanical interchangeability. This product page consolidates the verified LAN9117-MD role, family information, 10/100 Ethernet capability, 16-bit embedded-CPU interface, sourcing references, and migration cautions into a practical component-selection resource. Numeric electrical limits, pricing, pinout assignments, lifecycle details, and validated drop-in alternatives remain dependent on manufacturer or distributor data.
LAN9117-MT 10/100 Ethernet Controller | Microchip
The Microchip Technology LAN9117-MT is a single-chip 10/100 Ethernet controller with an integrated Base-T/TX PHY, parallel host interface, and 100-pin TQFP package. The verified distributor listing identifies support for 10/100 Base-T/TX networking and a parallel interface. It is designed for embedded systems requiring wired Ethernet without a separate external Ethernet transceiver. An Ethernet controller is an interface IC that connects an embedded processor or programmable controller to a physical Ethernet network. Within the broader semiconductor hierarchy, the LAN9117-MT belongs to the Ethernet controller family, network interface controllers, interface ICs, and communications semiconductors. By combining controller and physical-layer functions, it can reduce component count while preserving a parallel processor-facing integration path. The verified product information identifies 10 Mbps and 100 Mbps operation, a 3.3 V supply requirement, a 100-pin TQFP package, and a single-chip architecture. The -MT ordering suffix is associated with a tray package in the available distributor record. Other detailed electrical limits, host-interface timing, register features, media-type behavior, and environmental ratings were not included in the supplied verified excerpts and therefore are not asserted here. Typical uses include embedded industrial controllers, data-acquisition systems, building-automation equipment, access-control terminals, test instruments, and compact embedded servers. A parallel host interface can suit processors and controllers that do not include an integrated Ethernet MAC, while the integrated PHY simplifies the connection between the digital host bus and the analog magnetics interface. The primary design consideration is footprint verification: the DigiKey listing describes a 100-TQFP package measuring 14 mm by 14 mm, while another distributor excerpt states 14 mm by 20 mm. Engineers must confirm the exact ordering-code drawing and land pattern against the authoritative manufacturer package documentation before layout release. The -MT suffix and tray packaging must also be confirmed with the current manufacturer datasheet. This page combines verified manufacturer and distributor descriptions with explicit engineering caveats. It does not infer unavailable electrical, timing, thermal, or compliance values, and it separates confirmed product identity from details that still require datasheet-level verification.
LAN9118-MT 10/100 Ethernet Controller | Microchip
The Microchip Technology LAN9118-MT is a single-chip 10/100 Base-T/TX Ethernet controller with a 32-bit external parallel interface, a 3.3 V supply, and a 100-pin TQFP package. It combines an Ethernet controller and PHY for embedded systems requiring local network connectivity without a separate PCI bus controller. The device supports 10 Mbps and 100 Mbps Ethernet operation and is identified by the commercial temperature-grade -MT ordering suffix. An Ethernet controller is an interface integrated circuit that connects an embedded processor or microcontroller to a physical Ethernet network. The LAN9118 family belongs to the broader hierarchy of Ethernet controller -> network interface controller -> interface IC -> semiconductor. Integrating the controller and PHY supports embedded product designs for industrial controls, communications equipment, data acquisition, and networked peripherals, while the parallel host interface gives the host processor direct register and data access. The verified product information identifies a 32-bit external data bus, a 7-bit address bus, a 25 MHz clock capability, a 3.3 V supply, and a 100-pin TQFP package. The 100-pin package exposes the substantial parallel host interface required by the non-PCI architecture. The LAN9118-MT is therefore most appropriate where an embedded system has enough I/O and board area for a high-pin-count parallel interface rather than a compact serial Ethernet controller. The part is described as a high-performance single-chip 10/100 non-PCI Ethernet controller. Its combined controller and PHY architecture can reduce the number of external network-interface components compared with a separated MAC and physical-layer design. Ethernet magnetics and the RJ45 connector remain external, and the final signal-integrity and layout implementation must follow the manufacturer hardware guidance. The provided verification also identifies IEEE 802.3 and IEEE 802.3u compliance in a product comparison source. Typical uses include embedded Ethernet gateways, industrial monitoring equipment, serial-to-Ethernet systems, test instruments, and control systems that require 10/100 connectivity. The parallel interface makes the LAN9118-MT most attractive to designs with a processor bus capable of supporting the required data width and pin count. It is less suitable for highly constrained systems that favor a serial Ethernet interface or a smaller package. Designers should verify the complete pinout, voltage tolerances, clock requirements, decoupling, reset behavior, magnetics selection, and PCB routing against the manufacturer datasheet before layout release. The verified search results identify the manufacturer LAN9118 product page and multiple datasheet mirrors, but do not provide every electrical timing, pin-level, or lifecycle value needed for a complete production design.
LAN91C100FDTQFP - 10/100 Ethernet MAC Controller | Microchip
The Microchip Technology LAN91C100FDTQFP is a single-chip 10/100 Mb/s Ethernet Media Access Controller with an integrated Media Independent Interface, designed for first-generation Fast Ethernet adapters and embedded connectivity products. It is packaged in a 208-pin TQFP measuring 28 x 28 mm and uses CMOS technology. The controller supports IEEE 802.3 Ethernet operation, full-duplex capability, and an integrated 10/100 Ethernet MAC with MII connectivity. An Ethernet MAC controller is an interface IC that manages frame transmission, reception, address filtering, and access to the physical network medium. In the product hierarchy, the LAN91C100FDTQFP belongs to Ethernet controllers, within interface ICs and semiconductors. Its MII provides a standardized digital connection to an external Ethernet PHY, allowing system designers to separate network-medium conversion from MAC processing while retaining flexibility in magnetics and transceiver selection. Key characteristics include support for 10 Mb/s and 100 Mb/s Ethernet, IEEE 802.3 operation, full-duplex capability, commercial-temperature construction, and low-power shutdown. The MII interface makes the device suitable for embedded systems, industrial controllers, print servers, set-top equipment, and other legacy Fast Ethernet products that were designed around a dedicated MAC rather than an integrated Ethernet transceiver. Because the MAC does not include the physical-layer circuitry, the board still requires a compatible 10/100 Ethernet PHY and the associated magnetics and network interface components. The LAN91C100FDTQFP was developed for first-generation Fast Ethernet adapter designs, where implementation flexibility and external PHY selection were priorities. Its 208-pin package provides a broad set of parallel host and MII signals, while the large lead count makes careful high-speed trace routing, plane use, and ground-return design important. The controller operates from a digital CMOS environment, and its shutdown capability can reduce power consumption when the attached system does not require continuous network connectivity. Typical deployments include embedded industrial Ethernet equipment, legacy network adapters, printers, multifunction peripherals, embedded control systems, and purpose-built communication appliances. The controller is most appropriate when the host processor requires a dedicated Ethernet MAC but the product specification allows use of an external PHY. It is less attractive for new compact designs where an integrated MAC-and-PHY device would reduce board area, component count, and design effort. For implementation, follow the pin-description and reference-circuit tables in the manufacturer datasheet when assigning every ball or lead and selecting bypass capacitance. Preserve continuous ground-plane returns beneath the high-speed MII and host interface paths, terminate unused inputs according to the device requirements, and validate signal integrity with the selected PHY and board stack-up. This product page combines device identification, interface guidance, comparison considerations, and sourcing support to support legacy Fast Ethernet design work.
LAN91C110-PU - 10/100 Ethernet Controller | Microchip
The Microchip LAN91C110-PU is a 10/100 Base-TX Fast Ethernet controller with a generic 16/32-bit host interface, packaged in a 144-pin TQFP measuring 20 mm by 20 mm. It is designed for second-generation Fast Ethernet PC Card adapters and other non-PCI connectivity products. The controller implements the Media Access Control portion of the Ethernet protocol, placing Ethernet framing and medium-access functions in a dedicated interface IC. An Ethernet controller is a semiconductor that manages frame transmission and reception between a host processor and a network medium. The LAN91C110-PU provides a hardware interface suitable for systems whose CPU or system bus is not based on PCI. By using a generic parallel host interface, it can be connected to compatible processors and bus bridges without requiring a PCI-specific interface architecture. The principal feature set includes support for 10/100 Base-T/TX networking, a selectable 16-bit or 32-bit host interface, and an integrated Ethernet MAC function. The parallel interface provides a practical connection point for embedded systems, industrial controllers, legacy computer systems, and custom communications equipment. Its 144-pin TQFP package supports the numerous digital host, clock, reset, media, and power connections required by the controller and its external physical-layer interface. The LAN91C110-PU separates network-medium handling from the host-side system bus. The MAC processes Ethernet frame activity while the generic 16/32-bit interface transfers control and data information to the host processor. This division of responsibilities is particularly useful when a system already has an established embedded bus architecture but requires standards-based 10/100 Ethernet connectivity rather than a PCI peripheral arrangement. Typical applications include Fast Ethernet PC Card adapters, embedded control systems, industrial data-acquisition equipment, legacy network upgrades, and custom host-bus designs. It can also suit embedded Linux platforms and other processor-based equipment requiring a parallel Ethernet connection. System-level clocking, physical-layer connectivity, magnetic-interface components, and host-bus timing remain part of the complete design rather than functions implied solely by the controller IC. Designers should review the manufacturer datasheet before assigning signals because the complete 144-pin assignment, operating limits, interface timing, clock requirements, and recommended external networks must be followed exactly. PCB layout should preserve the required short paths, appropriate grounding, and controlled clock and data-routing geometry. Host firmware must also initialize the controller and configure its medium-access and host-interface operation according to the manufacturer procedure. This page organizes the confirmed device identity, package information, host-interface capabilities, use cases, sourcing path, and design considerations into an engineering-focused reference. It also distinguishes the controller's documented role from the additional PHY, magnetics, firmware, and bus-interface engineering required to build a complete Ethernet-connected product.
LAN91C111-NC 10/100 Ethernet MAC/PHY | Microchip Technology
The Microchip Technology LAN91C111-NC is a mixed-signal Ethernet interface IC that integrates a 10/100 Mbps Media Access Controller and Physical Layer in a 128-pin TQFP package. It supports 32-bit, 16-bit, and 8-bit host bus configurations, provides a MII interface, and includes 8 KB of dynamically configurable transmit and receive FIFO memory for embedded Ethernet designs. An Ethernet MAC-and-PHY controller provides the bridge between a host processor and a physical network connection. The MAC manages frame handling and CSMA/CD access, while the integrated PHY handles the physical signaling required for 10BASE-T or 100BASE-TX links. Integrating both functions into one device reduces component count and allows a host processor to connect to copper Ethernet without requiring a separate transceiver. The LAN91C111-NC supports data rates of 10 Mbps and 100 Mbps and implements the MAC and PHY portions of the CSMA/CD protocol. Its host interface can operate with 32-bit, 16-bit, or 8-bit data widths, helping the device accommodate processors with different bus capabilities. The internal MII connection between the MAC and PHY helps maintain throughput without using a separate external PHY bus. Internal transmit and receive FIFO memory is dynamically configurable and totals 8 KB. This buffering allows the host interface and Ethernet network activity to proceed at different effective rates, improving tolerance of host-bus access intervals. The MII interface also provides a standardized connection for additional physical-layer equipment and simplifies integration with related network-interface circuitry. Typical uses include industrial embedded systems, factory automation equipment, building controls, test equipment, print controllers, and compact embedded servers. A 100 Mbps link provides sufficient bandwidth for supervisory data, configuration traffic, telemetry, and moderate local file transfer. The selectable host-bus width is especially useful when adapting the controller to legacy parallel processor buses. The principal design task is matching the host-bus timing, interrupt structure, address mapping, and I/O voltage to the system processor. Place the device and its required external network components close together, route MII and host signals as controlled-impedance traces, and terminate unused inputs according to the manufacturer datasheet. Validate signal integrity and recovery behavior across the full set of line-rate and environmental conditions. This product record combines the Ethernet function description, package details, sourcing guidance, practical PCB considerations, and application-specific engineering context. It also distinguishes the device from true pin-compatible alternatives by applying a strict same-package and pin-compatibility requirement rather than presenting merely similar Ethernet controllers.
LAN91C111-NE - 10/100 Ethernet MAC + PHY | Microchip
The Microchip LAN91C111-NE is a single-chip 10/100 Ethernet controller integrating a Media Access Control layer and Physical Layer in a mixed-signal Analog/Digital device. It supports 10 Mbps and 100 Mbps operation, configurable 32-bit, 16-bit, or 8-bit host interfaces, full-duplex switched Ethernet, and 8 KB of dynamically configurable transmit and receive FIFO memory. The device uses an IEEE 802.3-compatible Ethernet architecture for embedded systems. An Ethernet MAC and PHY combined on one IC form the interface between an embedded host processor and a physical copper network. The MAC manages frame processing, addressing, collision handling, and data movement, while the PHY converts logical data into signals that can be transmitted over twisted-pair Ethernet. Integrating both functions reduces external component count and simplifies PCB routing compared with a separated MAC and transceiver design. The LAN91C111 family provides dual-speed 10/100 Mbps connectivity, AutoNegotiation, burst data transfer, and selectable host-bus widths. Its 8 KB internal FIFO buffer separates host processing from Ethernet timing, helping manage burst traffic on embedded processor buses. The flexible 8-, 16-, or 32-bit host interface allows the same controller architecture to address systems with different data-bus capabilities. The controller implements the MAC and PHY portions of the CSMA/CD protocol. Its receive path aligns scrambled data to IEEE 802.3 5B word boundaries, descrambles the recovered data, and transfers it to the 4B/5B decoder. On the transmit side, the integrated Ethernet engine prepares frames for the physical layer while the internal FIFOs buffer host and network traffic. This architecture supports both 10 Mbps and 100 Mbps links without requiring a separate Ethernet interface controller. Typical uses include embedded industrial controllers, factory automation equipment, embedded Web servers, set-top boxes, print systems, and network-connected embedded products. It is particularly useful where a host processor needs compact 10/100 Ethernet connectivity without a PCI bus or a separate physical-layer transceiver. The selectable host width also helps optimize external bus wiring and processor interface overhead. PCB design should preserve short, controlled impedance Ethernet traces and provide the external magnetic-interface components required by the application circuitry. Place the controller and supporting clock, decoupling, and interface components according to the manufacturer datasheet layout. Check the host-bus voltage, reset requirements, interrupt connections, and FIFO configuration in firmware before finalizing the system interface. This page combines the manufacturer architecture description with practical interface guidance, verified MPN comparison points, and implementation-oriented design notes. It is structured to help engineers identify the correct LAN91C111 ordering variant, plan the host interface, and evaluate the controller for compact embedded Ethernet designs.
LAN91C111-NS - 10/100 Ethernet MAC+PHY | Microchip
Microchip Technology LAN91C111-NS is a mixed-signal 10/100 Mb/s Ethernet controller integrating a Media Access Controller and Physical Layer in a 128-pin QFP package. It implements the MAC and PHY portions of the CSMA/CD protocol, supports 10 Mbps and 100 Mbps operation, and provides a parallel host interface selectable as 32-bit, 16-bit, or 8-bit. An Ethernet MAC and PHY controller is an integrated network interface for embedded equipment. The MAC manages frame handling and the CSMA/CD protocol, while the PHY connects the digital controller to a 10/100 Base-T Ethernet physical layer. Combining both functions reduces system complexity, conserves board area, and allows an embedded processor to communicate through a parallel host bus rather than requiring a separate Ethernet PHY. The LAN91C111-NS supports dual-speed operation at 100 Mbps or 10 Mbps with AutoNegotiation, as described in the manufacturer application note. Its architecture includes 8 KB of dynamically configurable transmit and receive FIFO SRAM, helping decouple host-bus traffic from network-frame activity. The parallel interface can operate at 32, 16, or 8 bits, providing flexibility for embedded processors with different external-bus capabilities. For 100BASE-TX operation, the descrambler processes the scrambled data recovered from the medium, follows the IEEE 802.3 scrambling rules, aligns the data on correct 5B word boundaries, and passes it to the 4B5B decoder. This mixed-signal architecture supports both 10BASE-T and 100BASE-TX networking while maintaining a host-facing digital interface. The manufacturer identifies the device as suitable for third-generation embedded Fast Ethernet connectivity solutions. Typical uses include industrial automation controllers, embedded network gateways, factory data-acquisition equipment, building-control systems, print servers, and compact network-access appliances. The selectable host-bus width is especially useful when balancing throughput, PCB routing, and processor-bus compatibility. AutoNegotiation allows the controller to operate with 10 Mb/s or 100 Mb/s network links while reducing manual speed configuration. Design the power, ground, clock, magnetics, and network-line interface according to the manufacturer reference implementation. Preserve the recommended placement and decoupling of the Ethernet magnetic components and provide the specified oscillator and crystal arrangement to avoid timing or compliance problems. Validate the completed board for conducted emissions, immunity, and Ethernet link performance before production. This page organizes the controller's principal network functions, interface options, package characteristics, application guidance, and qualified same-footprint alternatives. It also highlights design considerations that help engineers distinguish protocol coverage, host-bus flexibility, FIFO behavior, and physical-layer implementation without treating the device as a generic Ethernet block.
LAN91C111-NU - 10/100 Ethernet MAC/PHY | Microchip
The Microchip LAN91C111-NU is a single-chip 10/100 Base-T Ethernet controller integrating a Media Access Control layer and Physical Layer in a 128-lead TQFP package. It supports 10 Mbps and 100 Mbps operation, provides an 8/16/32-bit parallel host interface, and includes an 8 KB dynamically configurable transmit and receive FIFO. The device combines digital host-facing logic with analog PHY functions for embedded Ethernet connectivity. An Ethernet MAC and PHY are the two principal layers required for a conventional 10/100 Ethernet connection. The MAC organizes frames and manages access to the network, while the PHY converts digital data into signals suitable for twisted-pair cabling. Integrating both functions into one controller reduces external component count and simplifies embedded network designs compared with separate MAC and PHY implementations. The LAN91C111-NU belongs to the broader interface IC and Ethernet controller hierarchy. Key features include 10/100 Mbps dual-speed operation, support for 8-bit, 16-bit, and 32-bit host bus configurations, and 8 KB of internal FIFO memory. The manufacturer describes the LAN91C111 as implementing the MAC and PHY portions of CSMA/CD and using a parallel host interface suited to embedded processors. Its mixed-signal construction places network termination and transceiver functions alongside the digital controller logic. The configurable host interface allows a design to balance throughput, wiring, and memory efficiency. An 8-bit bus can reduce the number of processor connections, while a 32-bit bus can transfer data more efficiently when the host bus and system timing support it. The internal transmit and receive FIFOs help decouple host access from network timing, although firmware, interrupt handling, and buffer configuration remain essential parts of a reliable driver design. Typical applications include embedded industrial controllers, print servers, set-top boxes, embedded Linux systems, instrument-control equipment, and compact network appliances. The integrated 10/100 Ethernet interface is useful when a system needs a deterministic parallel host connection rather than a serial network interface. It can also support legacy Fast Ethernet equipment where both 10 Mbps and 100 Mbps operation are required. Layout is the primary design consideration. Place the Ethernet magnetics, line-side protection, and PHY-related components close to the network connector, while keeping the parallel host bus away from sensitive analog network traces. Confirm power, clock, reset, transceiver, and host-interface requirements against the manufacturer datasheet before releasing the PCB layout. The package library does not contain a dedicated 128-lead TQFP drawing, so use the manufacturer pin-description table for assignments. This page combines the LAN91C111-NU device function, verified family variants, cross-reference findings, application guidance, and practical integration considerations. It also distinguishes true same-package options from unrelated Ethernet controllers that may require different hosts, PHYs, packages, or driver changes.