MCP3422A7-E/MS - 18-Bit 2-Channel 240 SPS ADC | Microchip Technology
MPN: MCP3422A7-E/MS ✓ فعالMCP3422A7-E/MS نمای کلی
An ADC is a data-conversion IC that transforms continuous analog voltage into a digital numerical code for processing, measurement, or control. The MCP3422 belongs to the delta-sigma ADC family, where an internal modulator and digital filter shape the conversion process. In the broader semiconductor hierarchy, the MCP3422 is an ADC, then an analog and mixed-signal IC, and finally a semiconductor used in embedded measurement and instrumentation systems.
The MCP3422A7-E/MS provides up to 18-bit resolution, two differential inputs, an onboard precision 2.048 V reference, and a differential input range of plus or minus 2.048 V. Its 240 SPS conversion rate is suitable for slow-changing process, sensor, and instrumentation signals rather than high-speed waveform acquisition. The two-channel architecture allows simultaneous monitoring of two related measurements or differential sensing of a bridge or transducer.
The converter uses an I2C-compatible two-wire interface to transfer conversion results and configure operating conditions. Its differential input structure helps reject common-mode noise when the sensor is connected through balanced wiring. The integrated reference reduces the number of external components needed for ratiometric or absolute measurements, although the application must account for reference accuracy, noise, and power-supply behavior.
Typical uses include industrial process monitoring, low-frequency sensor acquisition, pressure and temperature measurement, environmental instrumentation, and embedded data acquisition systems. For bridge-based sensors, the differential inputs can reject much of the excitation-signal noise present on both sensor lines. For slowly varying voltages, the 240 SPS rate provides sufficient conversion bandwidth while averaging noise through the converter's digital filtering.
PCB implementation should prioritize short, symmetric analog traces, a quiet ground return, and separation between the analog inputs and switching nodes. The datasheet pin-description table should be used when assigning connector and test points. Verify the selected gain, conversion timing, reference configuration, and digital pull-ups before committing the layout.
This product page combines the manufacturer's device description with package, application, comparison, and design guidance for engineers evaluating the MCP3422A7-E/MS in precision, low-speed measurement systems.
جایگزینهای drop-in برای MCP3422A7-E/MS — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP3422A7-E/MS (همان فرمفاکتور و فوتپرینت) — متفاوت در Differential Input Range, Resolution, Input Channels, Sampling Rate, Package.
MCP3422A0-E/MS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A1-E/MS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A1T-E/MS
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP3422A3-E/MS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A2-E/MS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3422A7-E/MS حداکثر مقادیر مجاز و مشخصات الکتریکی
| رزولوشن | Up to 18 bits |
| Input Channels | 2 differential input channels |
| ADC Architecture | Delta-sigma |
| Conversion Rate | 240 SPS |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V differentially |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Digital Interface | I2C, 2-wire |
| محدوده دمای کاری | -40 C to +125 C |
| بستهبندی | 8-MSOP |
| Device Type | Analog-to-digital converter |
| Input Configuration | Differential inputs |
| On-Board Reference | Yes, precision 2.048 V reference |
| Output Resolution | 18-bit |
| Number of Inputs | 2 |
| نرخ نمونهبرداری | 240 samples per second |
راهنمای پیکربندی پین MCP3422A7-E/MS 8-msop
پیکربندی پین برای MCP3422A7-E/MS (پکیج 8-msop). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای MCP3422A7-E/MS.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
MCP3422A7-E/MS مناسب است برای 6 کاربردs: Industrial Process Monitoring, Temperature and Environmental Sensing, Bridge and Strain Measurement, Battery-Powered Environmental Instrumentation, Precision Data Acquisition, Power and Battery Monitoring.
Industrial Process Monitoring
The MCP3422A7-E/MS fits industrial process monitoring where sensors produce slowly changing voltages. Its 18-bit resolution and two differential channels allow a controller to measure two related process signals while rejecting common-mode disturbance. The 240 SPS conversion rate is appropriate for temperature, pressure, level, and flow transmitters that do not require waveform capture. The I2C interface reduces the number of host-controller connections, while the integrated 2.048 V reference simplifies scaling. Designers should isolate analog routing from motors, relays, and switching supplies, and should verify the selected gain and input range against the transmitter output.
پیشنهادی
Temperature and Environmental Sensing
The MCP3422A7-E/MS can acquire low-frequency temperature, humidity, and environmental sensor outputs in a compact embedded instrument. The two differential inputs are useful when one channel monitors a reference sensor and the other measures the target condition. Its up-to-18-bit resolution provides a high-resolution digital code, while the 240 SPS rate is more than sufficient for slow thermal changes. The integrated 2.048 V reference helps maintain consistent conversion scaling across both channels. Keep the sensor return path close to the analog ground reference and place filtering close to the device to prevent environmental noise from being sampled between conversions.
پیشنهادی
Bridge and Strain Measurement
The MCP3422A7-E/MS is suitable for bridge-based strain and pressure measurement because it provides two differential input channels and up to 18-bit resolution. A bridge output is small and commonly centered near a midpoint, so the ADC's differential architecture helps reject noise shared by both input lines. The 240 SPS rate supports static load, vibration-envelope, and slowly changing mechanical measurements. The integrated reference and I2C interface allow a compact instrumentation module to provide digital results without a separate reference controller. For best results, use symmetrical routing, a clean analog return, and appropriate input filtering while checking the sensor excitation requirements.
پیشنهادی
Battery-Powered Environmental Instrumentation
The MCP3422A7-E/MS can serve as the measurement front end in a battery-powered environmental node because its 2.7 V to 5.5 V supply range accommodates common embedded rails. The I2C interface allows the ADC to share a bus with a microcontroller or low-power sensor hub, reducing wiring and software complexity. Its 240 SPS rate suits periodic rather than continuous high-rate sampling, and the differential inputs help preserve measurement integrity in field wiring. The 8-MSOP package also supports compact PCB layouts. Power-management design should account for the ADC's operating current, input settling time, and the energy required for periodic sensor excitation.
پیشنهادی
Precision Data Acquisition
The MCP3422A7-E/MS is useful in precision data-acquisition systems that monitor two low-level, low-frequency signals. Its delta-sigma architecture, 18-bit resolution, differential inputs, and integrated 2.048 V reference are well aligned with laboratory and industrial measurements requiring stable digital output. The I2C interface provides a compact connection to a controller, while the 240 SPS limit makes the converter more suitable for temperature, position, and slow process variables than for oscilloscope-like waveforms. A careful analog layout, short input traces, and stable supply decoupling are essential to preserve the resolution promised by the converter.
پیشنهادی
Power and Battery Monitoring
The MCP3422A7-E/MS can measure differential battery-cell or power-rail voltages in a monitoring circuit. Its two channels support two monitored potentials or a differential measurement referenced to a common point. The 18-bit resolution can provide useful resolution for slowly changing supply conditions, and the internal 2.048 V reference simplifies calibration when the measured signal is scaled appropriately. The 240 SPS rate is sufficient for supervisory power measurements. However, high-voltage battery systems require external protection, attenuation, and isolation; the ADC itself is intended only for the specified 2.7 V to 5.5 V supply and input ranges.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP3422A7-E/MS — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP3422A0-E/MS | MCP3422A1-E/MS | MCP3422A1T-E/MS | MCP3422A3-E/MS |
|---|---|---|---|---|---|
| Package | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Special Features | Integrated 2.048 V reference and differential inputs | MCP3422-family differential ADC | MCP3422-family differential ADC | MCP3422-family differential ADC | MCP3422-family differential ADC |
تفاوتهای کلیدی
- 240 SPS conversion-rate option in an 18-bit two-channel ADC (در مقابلMCP3422A1-E/MS)
- Differential two-channel measurement with integrated reference (در مقابلMCP3422A0-E/MS)
- Same-footprint family alternative for PCB reuse (در مقابلMCP3422A3-E/MS)
- I2C integration simplifies digital connections (در مقابلMCP3422A1T-E/MS)
یادداشتهای طراحی
Route the two differential inputs as closely matched pairs and keep them away from switching nodes, relay contacts, and high-current return paths. Place input filtering and the ADC's supply bypass capacitors close to the relevant pins. A clean analog ground reference and short traces are especially important when using the converter's high-resolution modes.
The MCP3422A7-E/MS is intended for low-frequency, low-noise measurement rather than high-speed waveform capture. Keep sensor wiring short or use differential routing, establish a defined analog and digital grounding strategy, and validate the analog input bandwidth against the selected gain and conversion timing before adding external filters that could alter the measurement settling behavior.
The device operates from 2.7 V to 5.5 V, so the selected system rail must remain within that range including tolerance and transient excursions. Use local supply decoupling and verify that noise on the supply does not dominate the converter's noise performance. For battery-powered designs, account for the ADC's operating current and periodic-conversion duty cycle when estimating energy use.
Do not treat the 240 SPS maximum conversion rate as a general-purpose high-speed sampling capability. Confirm the selected gain, differential input range, conversion time, and I2C timing in the family datasheet. Also avoid assuming that the onboard 2.048 V reference makes external calibration unnecessary; offset, gain, reference accuracy, and PCB leakage can still affect the final measurement accuracy.
اطلاعات انطباق
The device information identifies the MCP3422 family and its 8-MSOP packaging, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not provided for this MPN.