MCP3422A7-E/MS - 18-Bit 2-Channel 240 SPS ADC | Microchip Technology
MPN: MCP3422A7-E/MS ✓ Hoạt độngMCP3422A7-E/MS Tóm tắt
An ADC is a data-conversion IC that transforms continuous analog voltage into a digital numerical code for processing, measurement, or control. The MCP3422 belongs to the delta-sigma ADC family, where an internal modulator and digital filter shape the conversion process. In the broader semiconductor hierarchy, the MCP3422 is an ADC, then an analog and mixed-signal IC, and finally a semiconductor used in embedded measurement and instrumentation systems.
The MCP3422A7-E/MS provides up to 18-bit resolution, two differential inputs, an onboard precision 2.048 V reference, and a differential input range of plus or minus 2.048 V. Its 240 SPS conversion rate is suitable for slow-changing process, sensor, and instrumentation signals rather than high-speed waveform acquisition. The two-channel architecture allows simultaneous monitoring of two related measurements or differential sensing of a bridge or transducer.
The converter uses an I2C-compatible two-wire interface to transfer conversion results and configure operating conditions. Its differential input structure helps reject common-mode noise when the sensor is connected through balanced wiring. The integrated reference reduces the number of external components needed for ratiometric or absolute measurements, although the application must account for reference accuracy, noise, and power-supply behavior.
Typical uses include industrial process monitoring, low-frequency sensor acquisition, pressure and temperature measurement, environmental instrumentation, and embedded data acquisition systems. For bridge-based sensors, the differential inputs can reject much of the excitation-signal noise present on both sensor lines. For slowly varying voltages, the 240 SPS rate provides sufficient conversion bandwidth while averaging noise through the converter's digital filtering.
PCB implementation should prioritize short, symmetric analog traces, a quiet ground return, and separation between the analog inputs and switching nodes. The datasheet pin-description table should be used when assigning connector and test points. Verify the selected gain, conversion timing, reference configuration, and digital pull-ups before committing the layout.
This product page combines the manufacturer's device description with package, application, comparison, and design guidance for engineers evaluating the MCP3422A7-E/MS in precision, low-speed measurement systems.
Bộ thay thế dễ dàng lắp đặt cho MCP3422A7-E/MS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCP3422A7-E/MS (cùng hình factor và footprint) — khác nhau ở Differential Input Range, Resolution, Input Channels, Sampling Rate, Package.
MCP3422A0-E/MS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MCP3422A1-E/MS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MCP3422A1T-E/MS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCP3422A3-E/MS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MCP3422A2-E/MS
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MCP3422A7-E/MS Tỷ lệ tối đa & tính chất điện
| Độ phân giải | Up to 18 bits |
| Input Channels | 2 differential input channels |
| ADC Architecture | Delta-sigma |
| Conversion Rate | 240 SPS |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V differentially |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Digital Interface | I2C, 2-wire |
| Khoảng nhiệt độ hoạt động | -40 C to +125 C |
| Hộp | 8-MSOP |
| Device Type | Analog-to-digital converter |
| Input Configuration | Differential inputs |
| On-Board Reference | Yes, precision 2.048 V reference |
| Output Resolution | 18-bit |
| Number of Inputs | 2 |
| Tỷ lệ lấy mẫu | 240 samples per second |
Hướng dẫn cấu hình chân MCP3422A7-E/MS 8-msop
Cấu hình chân cho MCP3422A7-E/MS (8-msop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP3422A7-E/MS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP3422A7-E/MS phù hợp cho 6 Áp dụngs: Industrial Process Monitoring, Temperature and Environmental Sensing, Bridge and Strain Measurement, Battery-Powered Environmental Instrumentation, Precision Data Acquisition, Power and Battery Monitoring.
Industrial Process Monitoring
The MCP3422A7-E/MS fits industrial process monitoring where sensors produce slowly changing voltages. Its 18-bit resolution and two differential channels allow a controller to measure two related process signals while rejecting common-mode disturbance. The 240 SPS conversion rate is appropriate for temperature, pressure, level, and flow transmitters that do not require waveform capture. The I2C interface reduces the number of host-controller connections, while the integrated 2.048 V reference simplifies scaling. Designers should isolate analog routing from motors, relays, and switching supplies, and should verify the selected gain and input range against the transmitter output.
Được đề xuất
Temperature and Environmental Sensing
The MCP3422A7-E/MS can acquire low-frequency temperature, humidity, and environmental sensor outputs in a compact embedded instrument. The two differential inputs are useful when one channel monitors a reference sensor and the other measures the target condition. Its up-to-18-bit resolution provides a high-resolution digital code, while the 240 SPS rate is more than sufficient for slow thermal changes. The integrated 2.048 V reference helps maintain consistent conversion scaling across both channels. Keep the sensor return path close to the analog ground reference and place filtering close to the device to prevent environmental noise from being sampled between conversions.
Được đề xuất
Bridge and Strain Measurement
The MCP3422A7-E/MS is suitable for bridge-based strain and pressure measurement because it provides two differential input channels and up to 18-bit resolution. A bridge output is small and commonly centered near a midpoint, so the ADC's differential architecture helps reject noise shared by both input lines. The 240 SPS rate supports static load, vibration-envelope, and slowly changing mechanical measurements. The integrated reference and I2C interface allow a compact instrumentation module to provide digital results without a separate reference controller. For best results, use symmetrical routing, a clean analog return, and appropriate input filtering while checking the sensor excitation requirements.
Được đề xuất
Battery-Powered Environmental Instrumentation
The MCP3422A7-E/MS can serve as the measurement front end in a battery-powered environmental node because its 2.7 V to 5.5 V supply range accommodates common embedded rails. The I2C interface allows the ADC to share a bus with a microcontroller or low-power sensor hub, reducing wiring and software complexity. Its 240 SPS rate suits periodic rather than continuous high-rate sampling, and the differential inputs help preserve measurement integrity in field wiring. The 8-MSOP package also supports compact PCB layouts. Power-management design should account for the ADC's operating current, input settling time, and the energy required for periodic sensor excitation.
Được đề xuất
Precision Data Acquisition
The MCP3422A7-E/MS is useful in precision data-acquisition systems that monitor two low-level, low-frequency signals. Its delta-sigma architecture, 18-bit resolution, differential inputs, and integrated 2.048 V reference are well aligned with laboratory and industrial measurements requiring stable digital output. The I2C interface provides a compact connection to a controller, while the 240 SPS limit makes the converter more suitable for temperature, position, and slow process variables than for oscilloscope-like waveforms. A careful analog layout, short input traces, and stable supply decoupling are essential to preserve the resolution promised by the converter.
Được đề xuất
Power and Battery Monitoring
The MCP3422A7-E/MS can measure differential battery-cell or power-rail voltages in a monitoring circuit. Its two channels support two monitored potentials or a differential measurement referenced to a common point. The 18-bit resolution can provide useful resolution for slowly changing supply conditions, and the internal 2.048 V reference simplifies calibration when the measured signal is scaled appropriately. The 240 SPS rate is sufficient for supervisory power measurements. However, high-voltage battery systems require external protection, attenuation, and isolation; the ADC itself is intended only for the specified 2.7 V to 5.5 V supply and input ranges.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP3422A7-E/MS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP3422A0-E/MS | MCP3422A1-E/MS | MCP3422A1T-E/MS | MCP3422A3-E/MS |
|---|---|---|---|---|---|
| Package | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP | 8-MSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Special Features | Integrated 2.048 V reference and differential inputs | MCP3422-family differential ADC | MCP3422-family differential ADC | MCP3422-family differential ADC | MCP3422-family differential ADC |
Bảo phân biệt quan trọng
- 240 SPS conversion-rate option in an 18-bit two-channel ADC (vsMCP3422A1-E/MS)
- Differential two-channel measurement with integrated reference (vsMCP3422A0-E/MS)
- Same-footprint family alternative for PCB reuse (vsMCP3422A3-E/MS)
- I2C integration simplifies digital connections (vsMCP3422A1T-E/MS)
Ghi chú thiết kế
Route the two differential inputs as closely matched pairs and keep them away from switching nodes, relay contacts, and high-current return paths. Place input filtering and the ADC's supply bypass capacitors close to the relevant pins. A clean analog ground reference and short traces are especially important when using the converter's high-resolution modes.
The MCP3422A7-E/MS is intended for low-frequency, low-noise measurement rather than high-speed waveform capture. Keep sensor wiring short or use differential routing, establish a defined analog and digital grounding strategy, and validate the analog input bandwidth against the selected gain and conversion timing before adding external filters that could alter the measurement settling behavior.
The device operates from 2.7 V to 5.5 V, so the selected system rail must remain within that range including tolerance and transient excursions. Use local supply decoupling and verify that noise on the supply does not dominate the converter's noise performance. For battery-powered designs, account for the ADC's operating current and periodic-conversion duty cycle when estimating energy use.
Do not treat the 240 SPS maximum conversion rate as a general-purpose high-speed sampling capability. Confirm the selected gain, differential input range, conversion time, and I2C timing in the family datasheet. Also avoid assuming that the onboard 2.048 V reference makes external calibration unnecessary; offset, gain, reference accuracy, and PCB leakage can still affect the final measurement accuracy.
Thông tin tuân thủ
The device information identifies the MCP3422 family and its 8-MSOP packaging, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not provided for this MPN.