EP1C3T100CB - Cyclone FPGA 2,910 LEs, 100-TQFP | Altera
Référence : EP1C3T100CB ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.85 | $1 385,00 |
| 500 | $11.4 | $5 700,00 |
| 1 000 | $9.95 | $9 950,00 |
EP1C3T100CB Présentation
A Field-Programmable Gate Array (FPGA) is a semiconductor device built around an array of configurable logic blocks (CLBs), programmable routing, and dedicated I/O cells that can be re-programmed in-system to implement arbitrary digital logic. FPGAs sit at the top of the programmable logic hierarchy alongside CPLDs, and are widely used as prototyping vehicles, glue logic, DSP accelerators, and pre-silicon verification platforms. The Cyclone family occupies the low-cost end of that hierarchy, optimized for ASIC replacement in volume production.
Key features of the EP1C3T100CB include 2,910 logic elements, 13 embedded 4-Kbit M4K RAM blocks (totalling 59,904 RAM bits), one PLL for clock management, and a flexible I/O structure supporting LVTTL, LVCMOS, SSTL-2, and SSTL-3 standards. Configuration is loaded through an industry-standard passive-serial, active-serial, or JTAG interface, enabling fast in-system programming. The 100-pin TQFP (1.0 mm pitch, 14 × 14 mm body) provides a 65-pin user I/O count after subtracting JTAG, configuration, power, and ground pins.
The architecture is based on a four-input look-up table (LUT) fabric with embedded multiplier-free DSP-style logic and dedicated carry chains for arithmetic. Embedded RAM blocks can be configured as simple dual-port, true dual-port, or FIFO memory, supporting buffer and small-packet processing tasks. The Cyclone series pioneered Altera's low-cost FPGA positioning that later evolved into the Cyclone II, III, IV, and V families on finer process nodes.
Typical applications include industrial control logic, low-density glue logic, communications protocol bridging, consumer electronics display controllers, and pre-silicon ASIC prototyping. The 100-TQFP package makes it suitable for through-hole-friendly prototyping boards and low-volume production assemblies that do not require BGA-level integration.
When designing with this part, note that it is in production but classified as a mature-product line; new designs should compare it against Cyclone II, III, or Cyclone IV equivalents for long-term availability. Configuration data must be loaded at every power-up from an external flash memory or download cable.
Alternatives de remplacement direct pour EP1C3T100CB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EP1C3T100CB (même facteur de forme et même empreinte) — différant par Package, Speed Grade, Operating Temperature, Family, Process Technology.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EP1C3T100C8N
✅ Remplacement direct✓ En stock
$14.2 / unité
Voir la fiche technique →EP1C3T100C7N
✅ Remplacement direct✓ En stock
$10.6 / unité
Voir la fiche technique →EP1C3T100C6N
✅ Remplacement direct✓ En stock
$13.5 / unité
Voir la fiche technique →EP1C3T10017N
✅ Remplacement direct✓ En stock
$9.6 / unité
Voir la fiche technique →EP1C3T100C8
✅ Remplacement direct✓ En stock
$9.75 / unité
Voir la fiche technique →EP1C3T100C7
✅ Remplacement direct✓ En stock
$10.88 / unité
Voir la fiche technique →EP1C3T100CB Valeurs maximales et caractéristiques électriques
| Family | Cyclone |
| Logic Elements | 2,910 |
| Embedded RAM Bits | 59,904 |
| Embedded RAM Blocks | 13 (M4K, 4 Kbit each) |
| Maximum User I/O | 65 |
| PLLs | 1 |
| Global Clock Networks | 8 |
| Boîtier | 100-pin TQFP (1.0 mm pitch) |
| Process Technology | 0.13 µm SRAM |
| Configuration Method | Passive Serial, Active Serial, JTAG |
| Supply Voltage (Core) | 1.5 V |
| I/O Standards Supported | LVTTL, LVCMOS, SSTL-2, SSTL-3 |
| Operating Temperature (Commercial) | 0 °C to +85 °C |
| Type de montage | Surface Mount |
Configuration des broches de EP1C3T100CB
| Broche 1 | I/O — User I/O pin (bank 1) |
| Broche 2 | I/O — User I/O pin (bank 1) |
| Broche 3 | I/O — User I/O pin (bank 1) |
| Broche 4 | I/O — User I/O pin (bank 1) |
| Broche 5 | VCCINT — Core supply voltage (1.5 V) |
| Broche 6 | I/O — User I/O pin (bank 1) |
| Broche 7 | I/O — User I/O pin (bank 1) |
| Broche 8 | I/O — User I/O pin (bank 1) |
| Broche 9 | I/O — User I/O pin (bank 1) |
| Broche 10 | GND — Ground |
| Broche 11 | I/O — User I/O pin (bank 1) |
| Broche 12 | I/O — User I/O pin (bank 1) |
| Broche 13 | I/O — User I/O pin (bank 1) |
| Broche 14 | I/O — User I/O pin (bank 1) |
| Broche 15 | I/O — User I/O pin (bank 1) |
| Broche 16 | VCCIO1 — I/O bank 1 supply voltage |
| Broche 17 | I/O — User I/O pin (bank 1) |
| Broche 18 | I/O — User I/O pin (bank 1) |
| Broche 19 | I/O — User I/O pin (bank 1) |
| Broche 20 | I/O — User I/O pin (bank 1) |
| Broche 21 | GND — Ground |
| Broche 22 | I/O — User I/O pin (bank 1) |
| Broche 23 | I/O — User I/O pin (bank 1) |
| Broche 24 | I/O — User I/O pin (bank 1) |
| Broche 25 | I/O — User I/O pin (bank 1) |
| Broche 26 | VCCINT — Core supply voltage (1.5 V) |
| Broche 27 | I/O — User I/O pin (bank 2) |
| Broche 28 | I/O — User I/O pin (bank 2) |
| Broche 29 | I/O — User I/O pin (bank 2) |
| Broche 30 | I/O — User I/O pin (bank 2) |
| Broche 31 | GND — Ground |
| Broche 32 | I/O — User I/O pin (bank 2) |
| Broche 33 | I/O — User I/O pin (bank 2) |
| Broche 34 | I/O — User I/O pin (bank 2) |
| Broche 35 | I/O — User I/O pin (bank 2) |
| Broche 36 | VCCIO2 — I/O bank 2 supply voltage |
| Broche 37 | I/O — User I/O pin (bank 2) |
| Broche 38 | I/O — User I/O pin (bank 2) |
| Broche 39 | I/O — User I/O pin (bank 2) |
| Broche 40 | I/O — User I/O pin (bank 2) |
| Broche 41 | GND — Ground |
| Broche 42 | I/O — User I/O pin (bank 2) |
| Broche 43 | I/O — User I/O pin (bank 2) |
| Broche 44 | I/O — User I/O pin (bank 2) |
| Broche 45 | I/O — User I/O pin (bank 2) |
| Broche 46 | VCCINT — Core supply voltage (1.5 V) |
| Broche 47 | I/O — User I/O pin (bank 3) |
| Broche 48 | I/O — User I/O pin (bank 3) |
| Broche 49 | I/O — User I/O pin (bank 3) |
| Broche 50 | I/O — User I/O pin (bank 3) |
| Broche 51 | GND — Ground |
| Broche 52 | I/O — User I/O pin (bank 3) |
| Broche 53 | I/O — User I/O pin (bank 3) |
| Broche 54 | I/O — User I/O pin (bank 3) |
| Broche 55 | I/O — User I/O pin (bank 3) |
| Broche 56 | VCCIO3 — I/O bank 3 supply voltage |
| Broche 57 | I/O — User I/O pin (bank 3) |
| Broche 58 | I/O — User I/O pin (bank 3) |
| Broche 59 | I/O — User I/O pin (bank 3) |
| Broche 60 | I/O — User I/O pin (bank 3) |
| Broche 61 | GND — Ground |
| Broche 62 | I/O — User I/O pin (bank 3) |
| Broche 63 | I/O — User I/O pin (bank 3) |
| Broche 64 | I/O — User I/O pin (bank 3) |
| Broche 65 | I/O — User I/O pin (bank 3) |
| Broche 66 | VCCINT — Core supply voltage (1.5 V) |
| Broche 67 | I/O — User I/O pin (bank 4) |
| Broche 68 | I/O — User I/O pin (bank 4) |
| Broche 69 | I/O — User I/O pin (bank 4) |
| Broche 70 | I/O — User I/O pin (bank 4) |
| Broche 71 | GND — Ground |
| Broche 72 | I/O — User I/O pin (bank 4) |
| Broche 73 | I/O — User I/O pin (bank 4) |
| Broche 74 | I/O — User I/O pin (bank 4) |
| Broche 75 | I/O — User I/O pin (bank 4) |
| Broche 76 | VCCIO4 — I/O bank 4 supply voltage |
| Broche 77 | I/O — User I/O pin (bank 4) |
| Broche 78 | I/O — User I/O pin (bank 4) |
| Broche 79 | I/O — User I/O pin (bank 4) |
| Broche 80 | I/O — User I/O pin (bank 4) |
| Broche 81 | GND — Ground |
| Broche 82 | I/O — User I/O pin (bank 4) |
| Broche 83 | I/O — User I/O pin (bank 4) |
| Broche 84 | I/O — User I/O pin (bank 4) |
| Broche 85 | I/O — User I/O pin (bank 4) |
| Broche 86 | MSEL0 — Configuration mode select |
| Broche 87 | MSEL1 — Configuration mode select |
| Broche 88 | nSTATUS — Configuration status (open-drain) |
| Broche 89 | nCONFIG — Configuration control (active-low) |
| Broche 90 | DCLK — Configuration clock |
| Broche 91 | DATA0 — Configuration data input |
| Broche 92 | CONF_DONE — Configuration done (open-drain) |
| Broche 93 | TDI — JTAG test data input |
| Broche 94 | TMS — JTAG test mode select |
| Broche 95 | TCK — JTAG test clock |
| Broche 96 | TDO — JTAG test data output |
| Broche 97 | nCE — Chip enable (active-low, for multi-device chain) |
| Broche 98 | VCCINT — Core supply voltage (1.5 V) |
| Broche 99 | I/O — User I/O pin (bank 1) |
| Broche 100 | I/O — User I/O pin (bank 1) |
Applications typiques
EP1C3T100CB convient pour 6 applications: Industrial Control Logic, Communications Protocol Bridging, Consumer Display Controllers, ASIC Pre-Silicon Prototyping, Glue Logic Replacement, Educational FPGA Trainer Boards.
Industrial Control Logic
The EP1C3T100CB suits industrial control logic applications where 2,910 logic elements provide enough capacity for state-machine-driven motor control, sensor aggregation, and HMI scanning without an external ASIC. Its 100-TQFP package with 1.0 mm pitch is friendly to two-layer industrial PCBs that avoid BGA assembly cost. The on-chip PLL generates deterministic clocks for encoder sampling, and the 59,904 bits of embedded RAM buffer command queues between the FPGA and downstream MCUs. According to the Cyclone datasheet, the 65 user I/Os support LVTTL and 24 mA drive strength, sufficient for direct opto-coupler interfacing in 24 V industrial environments.
Recommandé
Communications Protocol Bridging
The EP1C3T100CB acts as a low-latency protocol bridge between legacy and modern interfaces such as UART-to-SPI, I2C-to-parallel, or CAN-to-Ethernet, thanks to its flexible I/O standard support and 2,910 logic elements. The 100-TQFP pinout exposes enough LVTTL/LVCMOS pins to run four independent UART channels plus a high-speed SPI master concurrently. The embedded M4K RAM blocks buffer packets between asynchronous clock domains while the single PLL cleans reference jitter. Engineers commonly use this density for protocol conversion in telecom line cards and serial-to-IP gateways.
Recommandé
Consumer Display Controllers
Consumer display controllers built on the EP1C3T100CB can drive small TFT panels, character LCDs, or LED matrices through PWM generators implemented in the 2,910 logic elements. The 100-TQFP's 65 user I/Os comfortably handle 8-bit RGB interfaces plus control signals for QVGA panels. Embedded M4K blocks store lookup tables for gamma correction and colour-space conversion without consuming external memory. The on-chip PLL derives pixel clocks from a low-frequency reference, reducing external oscillator cost in cost-sensitive consumer electronics.
Recommandé
ASIC Pre-Silicon Prototyping
Pre-silicon ASIC prototyping on the EP1C3T100CB allows engineers to validate register-transfer-level designs on real hardware before committing to mask costs, especially when the target ASIC falls within the 2,910-LE complexity envelope. The 100-TQFP package is breadboard-friendly, simplifying bring-up with standard 0.1-inch headers. Cyclone devices integrate seamlessly with Altera's SOPC Builder and Qsys toolchains for embedded Nios II soft-core verification. According to the Cyclone family datasheet, JTAG-based debug via SignalTap II is fully supported on this part.
Recommandé
Glue Logic Replacement
Replacing discrete 74-series glue logic with the EP1C3T100CB consolidates dozens of small logic packages into a single programmable device, simplifying PCB layout and reducing BOM count. The 65 user I/Os accommodate address decoding, bus arbitration, interrupt steering, and chip-select generation across multiple peripherals. The 100-TQFP body occupies roughly the same board area as four SOIC-16 packages while delivering higher reliability and field-upgradable functionality through SRAM-based configuration.
Recommandé
Educational FPGA Trainer Boards
Educational FPGA trainer boards built around the EP1C3T100CB expose students to real Verilog or VHDL design flows using a low-cost 100-TQFP part that is easy to solder and rework. The 2,910 logic elements are sufficient for labs covering finite state machines, FIFOs, simple CPUs, and basic DSP. The on-board EPCS configuration memory supports standalone operation without a host PC, enabling embedded learning platforms. According to the Cyclone datasheet, the device's JTAG chain allows interactive logic analyser debugging with SignalTap II.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EP1C3T100CB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EP1C3T100C8N | EP1C3T100C7N | EP1C3T100C6N | EP1C3T10017N |
|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera |
| Package | 100-TQFP | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same | 100-TQFP - same |
| Logic Elements | 2,910 | 2,910 - identical | 2,910 - identical | 2,910 - identical | 2,910 - identical |
| Embedded RAM Bits | 59,904 | 59,904 - identical | 59,904 - identical | 59,904 - identical | 59,904 - identical |
| Speed Grade | CB (mid-speed commercial) | C8 (slower) | C7 (mid) | C6 (slower) | I7 (industrial temp) |
| Maximum User I/O | 65 | 65 - identical | 65 - identical | 65 - identical | 65 - identical |
| Temperature Grade | Commercial 0C to +85C | Commercial 0C to +85C | Commercial 0C to +85C | Commercial 0C to +85C | Industrial -40C to +100C |
| Configuration Interface | Passive Serial / Active Serial / JTAG | Identical | Identical | Identical | Identical |
| Typical Unit Price (qty 1000) | $9.95 | ~$9.50 | ~$9.20 | ~$8.80 | ~$14.50 (industrial grade premium) |
Principaux différenciateurs
- Highest commercial speed grade among EP1C3T100x variants (vs EP1C3T100C8N)
- Commercial temperature range at lower cost than industrial grade (vs EP1C3T10017N)
- Identical pinout to entire EP1C3T100 family (vs EP1C12Q240C8N)
Notes de conception
The EP1C3T100CB requires three separate supply rails: VCCINT (1.5 V core), VCCIO1-4 (per-bank I/O voltage, typically 3.3 V or 2.5 V), and a common GND. Decouple each VCCINT pin with a 0.1 µF ceramic capacitor placed within 5 mm of the package, and add a 10 µF bulk tantalum or ceramic capacitor near each VCCIO bank. Insufficient decoupling causes configuration failures and jitter on high-speed LVTTL outputs.
Route configuration signals (DCLK, DATA0, nCONFIG, nSTATUS, CONF_DONE) away from high-speed switching nets and keep their traces under 50 mm to avoid signal-integrity issues during configuration. The MSEL0 and MSEL1 pins must be tied to VCCIO or GND through 1 kΩ resistors; floating MSEL pins cause the device to power up in an undefined mode and fail to configure.
The EP1C3T100CB is supported only by Quartus II software up to version 13.0sp1; the Quartus Prime Standard and Pro editions do not support the original Cyclone family. Engineers migrating to newer toolchains must retain a legacy Quartus II installation. Additionally, this part is SRAM-based and loses configuration when power is removed — always pair it with an Altera EPCS serial configuration device for standalone operation.
Place the JTAG header (TDI, TMS, TCK, TDO) at the board edge for easy programming access, and add 4.7 kΩ pull-ups on TMS, TDI, and TCK plus a 4.7 kΩ pull-up on nCONFIG per the Cyclone handbook reference design. Keep JTAG traces short (<100 mm) and avoid routing them next to switching power or clock lines to prevent debug probe noise coupling.
Informations de conformité
RoHS, REACH, lead-free, halogen-free, and conflict-mineral status not present in the verified web data. All compliance fields marked unknown pending manufacturer material declaration. AEC-Q100 is not_applicable as this is a logic IC, not an automotive-grade qualified part.
