SN65HVD08D vs SN65HVD77D तुलना
विस्तृत दोनों ओर की तुलना SN65HVD08D द्वारा Texas Instruments और SN65HVD77D द्वारा Texas Instruments. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。
Texas Instruments
SN65HVD08D - 3.3/5V 10Mbps RS-485 Transceiver | Texas Instruments
SN65HVD08D ✓ सक्रियTexas Instruments
SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD77D ✓ सक्रियविशेषता तुलना
| पैरामीटर | SN65HVD08D | SN65HVD77D |
|---|---|---|
| ब्रांड | Texas Instruments | Texas Instruments |
| श्रेणी | Interface ICs | Interface ICs |
| लाइफसाइकिल स्थिति | सक्रिय | सक्रिय |
| Product Type | Half-duplex RS-485 transceiver | Full-duplex RS-485 transceiver |
| सप्लाई वोल्टेज | 3.3/5 V | — |
| Maximum Supply Voltage | 5.5 V | — |
| Maximum Data Rate | 10 Mbps | 50 Mbps |
| Quiescent Power Consumption | Less than 90 mW | — |
| Receiver Unit Load | 1/8 unit load | — |
| Maximum Bus Nodes | Up to 256 nodes | — |
| Bus-Pin ESD Protection | Exceeds 16 kV HBM | — |
| Driver Output Type | Three-state differential line driver | Differential |
| Receiver Type | Differential line receiver | — |
| Failsafe Receiver Behavior | Open-circuit, short-circuit, and idle-bus failsafe | — |
| Standards Compatibility | ANSI TIA/EIA-485-A and ISO-8482E | — |
| Cable-Powered Operation | 5-V power bus with up to 2 V line-voltage drop | — |
| पैकेज | 8-pin SOIC | 8-pin SOIC (D) |
| माउंटिंग प्रकार | Surface mount | Surface mount |
| ऑपरेटिंग तापमान रेंज | [DATA_NEEDED: operating temperature range] | -40°C to 125°C |
| RoHS स्थिति | [DATA_NEEDED: RoHS status] | Compliant |
| REACH Status | [DATA_NEEDED: REACH status] | — |
| Supply Voltage Range | — | 3.0 V to 3.6 V |
| Nominal Supply Voltage | — | 3.3 V |
| Number of Drivers | — | 1 |
| Number of Receivers | — | 1 |
| Duplex Mode | — | Full duplex |
| Supported Standards | — | RS-485 and RS-422 |
| ESD Protection | — | ±12 kV IEC |
| Package Width | — | 3.90 mm |
| External Enable Controls | — | None |
| Receiver Output Type | — | Single-ended logic output |
| Low-Power Standby Current | — | Less than 5 µA when driver and receiver are disabled |
| Termination Requirement | — | External termination required |