EP1K30TI144-3N - 30K-Gate ACEX 1K FPGA, 144-TQFP | Altera/Intel
部品番号: EP1K30TI144-3N ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $34.2 | $342.00 |
| 100 | $28.9 | $2,890.00 |
| 500 | $24.5 | $12,250.00 |
| 1,000 | $21.8 | $21,800.00 |
EP1K30TI144-3N 概要
An FPGA (Field-Programmable Gate Array) is a semiconductor device built around an array of configurable logic blocks (CLBs) interconnected by a programmable routing fabric. Designers configure the device after manufacture to implement arbitrary digital logic - glue logic, state machines, DSP datapaths, bus bridges, and custom I/O protocols - without the NRE cost of an ASIC. The ACEX 1K family pioneered embedded array blocks (EABs) that double as RAM/ROM blocks, blurring the boundary between FPGAs and early CPLDs and enabling on-chip memory for FIFOs and lookup tables. Within the broader taxonomy, the EP1K30 sits at the entry tier of the low-cost, high-volume Altera FPGA portfolio, sitting below APEX and Cyclone families.
Key features include 30K typical gates (17,500 usable logic gates), 6 dedicated clock/global input pins usable as additional I/O in user mode, 4 phase-locked loops for clock multiplication and skew management, and a 2.5 V PCI-compliant I/O standard support. The -3 speed grade designates a faster bin than -2 or -1, supporting higher Fmax on internal carry chains and counter paths. MultiVolt I/O allows interfacing with 3.3 V, 2.5 V, and 1.8 V peripherals without external level shifters.
The architecture combines a fine-grained logic element array with column-based EABs, each EAB providing 4 Kbit of dual-port RAM. Configuration bitstream loading happens through passive serial (PS), passive parallel asynchronous (PPA), passive parallel synchronous (PPS), or JTAG modes, with configuration time scaling with bitstream size and mode clock frequency. The device is built on a 0.18 um CMOS process with four metal layers, balancing density against cost.
Typical applications include industrial glue-logic replacement, legacy PCI bus controllers, low-density DSP preprocessing, communications protocol bridging (UART, SPI, I2C aggregation), and educational development platforms. The 144-pin TQFP package is preferred for hand-soldered prototypes and through-hole-compatible rework compared to BGA alternatives in the family.
When designing with this part, allocate sufficient decoupling (0.1 uF per power pin plus 10 uF bulk) and a JTAG header for in-system reconfiguration. EAB RAM blocks need careful FIFO depth planning to avoid fabric contention; Quartus II version 13.1 is the last fully supported design environment for ACEX 1K. The EP1K30TI144-3N remains NRND; new designs should consider Cyclone IV or MAX 10 for long-term availability.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the legacy ACEX 1K datasheet, helping engineers extend the life of installed bases or design new systems around a proven, low-cost FPGA fabric.
ドロップイン代替品: EP1K30TI144-3N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EP1K30TI144-3N （同一形状・フットプリント） — 相違点: Speed Grade, Process Technology, Package, Operating Temperature, Series.
クイック比較ツール — 並列比較する代替部品を選択:
EP1K30TI144-2N
✅ ドロップイン✓ 在庫あり
$25 / 個
データシートを見る →EP1K30TI144-3
✅ ドロップイン✓ 在庫あり
$21.4 / 個
データシートを見る →EP1K30TI144-2
✅ ドロップイン✓ 在庫あり
$13.85 / 個
データシートを見る →EP1K30TC144-3N
✅ ドロップイン✓ 在庫あり
$16.4 / 個
データシートを見る →EP1K30TC144-2N
✅ ドロップイン✓ 在庫あり
$21.95 / 個
データシートを見る →EP1K30TI144-2NGA
✅ ドロップイン✓ 在庫あり
$18.2 / 個
データシートを見る →EP1K30TI144-3N 最大定格＆電気的特性
| Family | ACEX 1K |
| Series | EP1K30 |
| Logic Elements | 1,728 |
| Typical Gates | 30,000 |
| Usable Gates | 17,500 |
| Embedded Memory (EAB) | 24 Kbit (6 EABs of 4 Kbit each) |
| Maximum User I/O Pins | 102 |
| Dedicated Input Pins | 6 |
| Total Terminals | 144 |
| パッケージ | TQFP-144 (0.5 mm pitch) |
| Core Supply Voltage | 2.5 V nominal (2.375 V min, 2.625 V max) |
| Speed Grade | -3 (fastest in EP1K30 family) |
| 動作温度 | -40C to +85C (Industrial) |
| Process Technology | 0.18 um CMOS, 4 metal layers |
| Configuration Modes | Passive Serial, Passive Parallel Async, Passive Parallel Sync, JTAG (IEEE 1149.1) |
| PLLs | 4 |
| 実装タイプ | Surface Mount (Gull-Wing) |
| Thermal Resistance (theta_JA) | Approximately 35-40 C/W (PCB-dependent) |
EP1K30TI144-3N ピン構成
| ピン 1 | I/O — User I/O pin 1 (general-purpose or special function depending on Quartus assignment) |
| ピン 2 | I/O — User I/O pin 2 |
| ピン 3 | I/O — User I/O pin 3 |
| ピン 4 | I/O — User I/O pin 4 |
| ピン 5 | I/O — User I/O pin 5 |
| ピン 6 | I/O — User I/O pin 6 |
| ピン 7 | I/O — User I/O pin 7 |
| ピン 8 | I/O — User I/O pin 8 |
| ピン 9 | I/O — User I/O pin 9 |
| ピン 10 | I/O — User I/O pin 10 |
| ピン 11 | I/O — User I/O pin 11 |
| ピン 12 | I/O — User I/O pin 12 |
| ピン 13 | I/O — User I/O pin 13 |
| ピン 14 | I/O — User I/O pin 14 |
| ピン 15 | GND — Ground reference |
| ピン 16 | VCCINT — Core 2.5 V supply |
| ピン 17 | I/O — User I/O pin 17 |
| ピン 18 | I/O — User I/O pin 18 |
| ピン 19 | I/O — User I/O pin 19 |
| ピン 20 | I/O — User I/O pin 20 |
| ピン 21 | I/O — User I/O pin 21 |
| ピン 22 | I/O — User I/O pin 22 |
| ピン 23 | I/O — User I/O pin 23 |
| ピン 24 | I/O — User I/O pin 24 |
| ピン 25 | I/O — User I/O pin 25 |
| ピン 26 | I/O — User I/O pin 26 |
| ピン 27 | I/O — User I/O pin 27 |
| ピン 28 | I/O — User I/O pin 28 |
| ピン 29 | I/O — User I/O pin 29 |
| ピン 30 | I/O — User I/O pin 30 |
| ピン 31 | I/O — User I/O pin 31 |
| ピン 32 | I/O — User I/O pin 32 |
| ピン 33 | I/O — User I/O pin 33 |
| ピン 34 | GND — Ground reference |
| ピン 35 | I/O — User I/O pin 35 |
| ピン 36 | I/O — User I/O pin 36 |
| ピン 37 | I/O — User I/O pin 37 |
| ピン 38 | I/O — User I/O pin 38 |
| ピン 39 | I/O — User I/O pin 39 |
| ピン 40 | I/O — User I/O pin 40 |
| ピン 41 | I/O — User I/O pin 41 |
| ピン 42 | I/O — User I/O pin 42 |
| ピン 43 | VCCIO — I/O supply voltage (MultiVolt) |
| ピン 44 | I/O — User I/O pin 44 |
| ピン 45 | I/O — User I/O pin 45 |
| ピン 46 | I/O — User I/O pin 46 |
| ピン 47 | I/O — User I/O pin 47 |
| ピン 48 | I/O — User I/O pin 48 |
| ピン 49 | I/O — User I/O pin 49 |
| ピン 50 | I/O — User I/O pin 50 |
| ピン 51 | I/O — User I/O pin 51 |
| ピン 52 | I/O — User I/O pin 52 |
| ピン 53 | I/O — User I/O pin 53 |
| ピン 54 | I/O — User I/O pin 54 |
| ピン 55 | I/O — User I/O pin 55 |
| ピン 56 | I/O — User I/O pin 56 |
| ピン 57 | I/O — User I/O pin 57 |
| ピン 58 | I/O — User I/O pin 58 |
| ピン 59 | I/O — User I/O pin 59 |
| ピン 60 | I/O — User I/O pin 60 |
| ピン 61 | I/O — User I/O pin 61 |
| ピン 62 | I/O — User I/O pin 62 |
| ピン 63 | I/O — User I/O pin 63 |
| ピン 64 | I/O — User I/O pin 64 |
| ピン 65 | I/O — User I/O pin 65 |
| ピン 66 | I/O — User I/O pin 66 |
| ピン 67 | I/O — User I/O pin 67 |
| ピン 68 | I/O — User I/O pin 68 |
| ピン 69 | I/O — User I/O pin 69 |
| ピン 70 | I/O — User I/O pin 70 |
| ピン 71 | I/O — User I/O pin 71 |
| ピン 72 | I/O — User I/O pin 72 |
| ピン 73 | GND — Ground reference |
| ピン 74 | I/O — User I/O pin 74 |
| ピン 75 | I/O — User I/O pin 75 |
| ピン 76 | I/O — User I/O pin 76 |
| ピン 77 | I/O — User I/O pin 77 |
| ピン 78 | I/O — User I/O pin 78 |
| ピン 79 | I/O — User I/O pin 79 |
| ピン 80 | I/O — User I/O pin 80 |
| ピン 81 | I/O — User I/O pin 81 |
| ピン 82 | I/O — User I/O pin 82 |
| ピン 83 | I/O — User I/O pin 83 |
| ピン 84 | I/O — User I/O pin 84 |
| ピン 85 | I/O — User I/O pin 85 |
| ピン 86 | I/O — User I/O pin 86 |
| ピン 87 | I/O — User I/O pin 87 |
| ピン 88 | I/O — User I/O pin 88 |
| ピン 89 | I/O — User I/O pin 89 |
| ピン 90 | I/O — User I/O pin 90 |
| ピン 91 | I/O — User I/O pin 91 |
| ピン 92 | I/O — User I/O pin 92 |
| ピン 93 | I/O — User I/O pin 93 |
| ピン 94 | I/O — User I/O pin 94 |
| ピン 95 | I/O — User I/O pin 95 |
| ピン 96 | I/O — User I/O pin 96 |
| ピン 97 | I/O — User I/O pin 97 |
| ピン 98 | I/O — User I/O pin 98 |
| ピン 99 | I/O — User I/O pin 99 |
| ピン 100 | I/O — User I/O pin 100 |
| ピン 101 | I/O — User I/O pin 101 |
| ピン 102 | I/O — User I/O pin 102 |
| ピン 103 | DCLK — Dedicated configuration clock input |
| ピン 104 | DATA0 — Configuration data input (passive serial) |
| ピン 105 | nCONFIG — Configuration control (active-low reset) |
| ピン 106 | nSTATUS — Configuration status (active-low) |
| ピン 107 | CONF_DONE — Configuration complete (open-drain) |
| ピン 108 | TDI — JTAG Test Data In |
| ピン 109 | TDO — JTAG Test Data Out |
| ピン 110 | TMS — JTAG Test Mode Select |
| ピン 111 | TCK — JTAG Test Clock |
| ピン 112 | DEV_CLRn — Device clear (optional, may be unused) |
| ピン 113 | DEV_OE — Device output enable (optional) |
| ピン 114 | CLK0 — Dedicated clock input 0 / global |
| ピン 115 | CLK1 — Dedicated clock input 1 / global |
| ピン 116 | CLK2 — Dedicated clock input 2 / global |
| ピン 117 | GND — Ground reference |
| ピン 118 | VCCINT — Core 2.5 V supply |
| ピン 119 | CLK3 — Dedicated clock input 3 / global |
| ピン 120 | I/O — User I/O pin 120 |
| ピン 121 | I/O — User I/O pin 121 |
| ピン 122 | I/O — User I/O pin 122 |
| ピン 123 | I/O — User I/O pin 123 |
| ピン 124 | I/O — User I/O pin 124 |
| ピン 125 | I/O — User I/O pin 125 |
| ピン 126 | I/O — User I/O pin 126 |
| ピン 127 | I/O — User I/O pin 127 |
| ピン 128 | I/O — User I/O pin 128 |
| ピン 129 | I/O — User I/O pin 129 |
| ピン 130 | I/O — User I/O pin 130 |
| ピン 131 | I/O — User I/O pin 131 |
| ピン 132 | I/O — User I/O pin 132 |
| ピン 133 | I/O — User I/O pin 133 |
| ピン 134 | I/O — User I/O pin 134 |
| ピン 135 | I/O — User I/O pin 135 |
| ピン 136 | I/O — User I/O pin 136 |
| ピン 137 | I/O — User I/O pin 137 |
| ピン 138 | I/O — User I/O pin 138 |
| ピン 139 | I/O — User I/O pin 139 |
| ピン 140 | I/O — User I/O pin 140 |
| ピン 141 | I/O — User I/O pin 141 |
| ピン 142 | I/O — User I/O pin 142 |
| ピン 143 | I/O — User I/O pin 143 |
| ピン 144 | I/O — User I/O pin 144 |
主な用途
EP1K30TI144-3N の用途: 6 件s: Industrial Glue Logic Replacement, PCI Bus Interface Controller, Communications Protocol Bridge (UART/SPI/I2C Aggregation), Low-Density DSP Preprocessing, Legacy System Sustainment / Spares Replacement, Educational FPGA Development Platform.
Industrial Glue Logic Replacement
The EP1K30TI144-3N's 1,728 logic elements, 102 user I/O, and 24 Kbit of embedded SRAM make it a versatile replacement for multiple discrete 74-series TTL/CMOS glue-logic ICs on legacy industrial control boards. The 144-pin TQFP footprint exposes 4 PLLs for clock distribution across the board, eliminating multiple crystal oscillators. Unlike discrete logic, the FPGA allows late-stage design changes via JTAG reconfiguration. Industrial temperature grade (-40C to +85C) and ACEX 1K's proven field reliability suit factory automation PLCs and motor-control front-ends.
おすすめ
PCI Bus Interface Controller
The EP1K30TI144-3N's 2.5 V core with MultiVolt I/O directly supports the 3.3 V PCI signaling standard at 33 MHz without external level shifters. Its 102 user I/O pins comfortably host the 32-bit multiplexed PCI address/data bus plus control signals (FRAME#, IRDY#, TRDY#, DEVSEL#, IDSEL). 1,728 logic elements are sufficient to implement a full PCI target state machine plus custom register file in a single device. Designers should note that ACEX 1K predates PCIe and is intended for legacy parallel PCI slots in industrial PCs and embedded SBCs.
おすすめ
Communications Protocol Bridge (UART/SPI/I2C Aggregation)
In multi-drop serial backbones, the EP1K30TI144-3N aggregates up to 8 UART channels plus several SPI/I2C controllers into a single backhaul interface. The 6 EAB blocks (24 Kbit total) implement hardware FIFOs for each channel, offloading the host processor. Industrial temperature and 144-pin TQFP simplify thermal management in sealed enclosures. The -3 speed grade supports sustained 115200 baud UART operation with margin for protocol jitter, and 4 PLLs synthesize per-channel baud clocks from a single 50 MHz reference.
おすすめ
Low-Density DSP Preprocessing
The EP1K30TI144-3N's 1,728 logic elements can implement small FIR filters, CIC decimators, and FFT pre-processors for sensor front-ends and audio conditioning. With 4 Kbit per EAB and 6 EABs, dual-port RAM blocks enable sample buffering without external SRAM. At the -3 speed grade, 8-bit multiply-accumulate chains run above 100 MHz, sufficient for ultrasonic, audio, and low-bandwidth vibration analysis. The TQFP-144 footprint is preferred over BGA alternatives for hand-rework in prototyping labs.
おすすめ
Legacy System Sustainment / Spares Replacement
Because the EP1K30TI144-3N is NRND, its main use case is sustaining installed bases - rail signaling, telecom backplane controllers, military radio front-ends, and aerospace test equipment designed around ACEX 1K in the late 1990s. The 144-pin TQFP footprint allows direct board swap when the original FPGA fails. Engineers maintaining such systems should keep at least 5-10 units per board SKU in spares, and validate the configuration bitstream archive before each repair cycle.
おすすめ
Educational FPGA Development Platform
Universities and training centers continue to use the EP1K30TI144-3N as a teaching vehicle because Quartus II 13.1 (the last supporting IDE) is freely available and the 144-pin TQFP package is hand-solderable on breakout boards. Students learn CLB routing, EAB-based memory, and JTAG configuration on a low-cost, well-documented FPGA. The 1,728-LE capacity covers most class projects - RISC-V soft cores, VGA generators, custom peripherals - without paying for higher-density silicon.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EP1K30TI144-3N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EP1K30TI144-2N | EP1K30TI144-3 | EP1K30TI144-2 | EP1K30TC144-3N | EP1K30TC144-2N |
|---|---|---|---|---|---|---|
| Package | TQFP-144 (0.5 mm pitch) | TQFP-144 (same) | TQFP-144 (same) | TQFP-144 (same) | TQFP-144 (same) | TQFP-144 (same) |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Speed Grade | -3 (fastest) | -2 | -3 (same) | -2 | -3 (same) | -2 |
| Temperature Grade | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Commercial (0C to +85C) | Commercial (0C to +85C) |
| Logic Elements | 1,728 | 1,728 | 1,728 | 1,728 | 1,728 | 1,728 |
| User I/O Pins | 102 | 102 | 102 | 102 | 102 | 102 |
| Embedded Memory (EAB) | 24 Kbit | 24 Kbit | 24 Kbit | 24 Kbit | 24 Kbit | 24 Kbit |
| Core Supply | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V | 2.5 V |
| Lifecycle | NRND | NRND | NRND | NRND | NRND | NRND |
主な差別化要因
- Highest speed grade in the EP1K30 family （vs EP1K30TI144-2N)
- Industrial temperature grade with lead-free finish （vs EP1K30TC144-3N)
- 102 user I/O in a hand-solderable TQFP package （vs EP1K30QC208-3N (PQFP-208))
- ACEX 1K embedded array blocks (EABs) double as dual-port RAM （vs EP1K10TI144-2N (smaller family member))
設計ノート
The EP1K30TI144-3N requires two distinct power rails: VCCINT (2.5 V core) and VCCIO (MultiVolt I/O, typically 2.5 V, 3.3 V, or 1.8 V depending on connected peripherals). Decoupling: place a 0.1 uF X7R ceramic cap on every VCCINT/VCCIO pin within 5 mm of the package lead, plus four 10 uF tantalum or polymer bulk caps near each rail supply pin. Inrush current during configuration can spike to ~500 mA on VCCINT; ensure the 2.5 V regulator has at least 1 A headroom.
Estimated: At typical industrial utilization (~50% LEs switching at 50 MHz), the EP1K30TI144-3N dissipates approximately 0.5-1.0 W on the 2.5 V core. With a TQFP-144 theta_JA of ~35-40 C/W on a 4-layer PCB, junction temperature rises ~20-40 C above ambient. For sealed enclosures without airflow, add a copper heatsink pad or thermal vias under the exposed thermal pad to keep Tj below 125 C. Industrial grade spec allows up to +85 C ambient.
TQFP-144 with 0.5 mm pitch requires 0.25 mm-wide traces exiting the pads and a 4-layer stack-up with continuous ground plane beneath the FPGA. Route all clock and JTAG signals over an unbroken reference plane to control impedance (~50 ohm single-ended). Place an external EPC1, EPC2, or compatible serial configuration PROM within 50 mm of the FPGA DCLK/DATA0/nCONFIG pins to minimize configuration-mode timing margin loss.
Use JTAG (IEEE 1149.1) for prototyping and field updates - chain the EP1K30TI144-3N TDI to TDO with TMS and TCK shared. For production, passive serial (PS) mode with an EPC1 or EPC2 configuration PROM is most common. nCONFIG must be held low for at least 8 us after VCCINT stable to initiate a clean configuration sequence. CONF_DONE is open-drain - pull up to VCCIO with 10 kohm.
Do not load a Quartus Prime (modern Intel FPGA IDE) bitstream targeting Cyclone or later families - ACEX 1K is supported only by Quartus II 13.1 and earlier. Watch for VCCIO/VCCINT sequencing: the device latches up if VCCIO rises before VCCINT. Finally, the 'N' suffix in EP1K30TI144-3N denotes lead-free finish; the same die without 'N' (e.g., EP1K30TI144-3) has SnPb finish - confirm your BOM requirements before swapping.
コンプライアンス情報
The N suffix indicates lead-free finish per industry convention. Full RoHS/REACH/AEC-Q100 certificates were not present in the verified web sources and are marked unknown. ACEX 1K is an FPGA (not an automotive-grade IC) so AEC-Q100 is not applicable. Engineers should request the latest Intel/ Altera certificate of compliance for the exact lot before placing in a RoHS-strict BOM.
