10M16DCF256C7G - MAX 10 FPGA, 16K LE, 256-FBGA | Intel
부품 번호: 10M16DCF256C7G ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.02 | $18.02 |
| 10 | $16.4 | $164.00 |
| 100 | $14.55 | $1,455.00 |
| 500 | $13.1 | $6,550.00 |
| 1,000 | $11.75 | $11,750.00 |
10M16DCF256C7G 개요
An FPGA (Field-Programmable Gate Array) is a semiconductor device built around an array of configurable logic blocks (CLBs), embedded memory, DSP blocks, and programmable I/O, all wired together through a programmable interconnect. FPGAs occupy a tier between standard microcontrollers and ASICs in the system-design hierarchy, offering hardware-level parallelism, nanosecond-latency I/O response, and the ability to be reconfigured in-system via JTAG or active serial. The MAX 10 family is Intel's small-form-factor, low-power, non-volatile line intended for I/O expansion, bridge, and glue-logic applications.
Key features of the 10M16DCF256C7G include 16,000 logic elements, 378 Kbits of M9K block memory, 45 embedded 18x18 multipliers, four general-purpose PLLs, two analog front-end blocks each containing a 12-bit ADC and temperature-sensing diode, and a 3.3 V core/auxiliary supply with multi-voltage I/O banks supporting 1.2 V to 3.3 V single-ended standards. The dual-boot flash and instant-on feature enable configuration in under 10 ms from power-up.
The device is fabricated on a TSMC 55 nm embedded flash process, which is what gives MAX 10 its non-volatile behavior. The 256-FBGA package has a 17 x 17 mm body with 1.0 mm ball pitch, making it suitable for space-constrained boards that need high I/O density. Configuration sources include JTAG, internal flash, and standard serial modes through Quartus Prime software.
Typical applications include industrial motor control, video bridging and image aggregation, I/O expansion for processors, portable medical device front-ends, and factory automation. The 10M16DCF256C7G is especially useful in designs that need parallel DSP and logic without paying the cost of a high-end FPGA.
When designing with this part, ensure that all configuration mode pins (MSEL) are tied to the correct logic levels for the desired boot mode, and provide adequate decoupling across the 1.2 V, 2.5 V, and 3.3 V rails. Thermal management is generally straightforward because the 256-FBGA package offers good heat spreading, but at sustained 1 GHz internal clock rates the junction temperature should still be calculated against ambient.
드롭인 대체품: 10M16DCF256C7G — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: 10M16DCF256C7G (동일 폼 팩터 및 풋프린트) — 차이점: Package, Logic Elements (LE), Process Technology, Speed Grade, User Flash Memory.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
10M16DCF256A7G
✅ 드롭인✓ 재고 있음
$37.2 / 개
데이터시트 보기 →10M16DCF256I7G
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$24.95 / 개
데이터시트 보기 →10M16DAF256C7G
✅ 드롭인✓ 재고 있음
$13.8 / 개
데이터시트 보기 →10M08DCF256C7G
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
10M08DCF256C8G
✅ 드롭인✓ 재고 있음
$2.28 / 개
데이터시트 보기 →10M08DAF256C7G
✅ 드롭인✓ 재고 있음
$7.95 / 개
데이터시트 보기 →10M16DCF256C7G 최대 정격 & 전기적 특성
| Family | MAX 10 |
| Logic Elements | 16,000 |
| Adaptive Logic Modules (ALMs) | 10,000 |
| Embedded Memory (M9K blocks) | 378 Kbits / 42 blocks |
| Total Embedded Memory Bits | 562,176 bits |
| Embedded 18x18 Multipliers | 45 |
| Maximum User I/Os | 178 |
| General-Purpose PLLs | 4 |
| Analog Front-End Blocks (ADC) | 2 (12-bit, 1 MSPS) |
| Configuration Flash | Dual-configuration, internal |
| 패키지 | 256-FBGA (F256), 17 x 17 mm, 1.0 mm pitch |
| 실장 유형 | Surface Mount |
| Core Voltage | 1.2 V |
| Auxiliary / I/O Voltages | 1.2 V to 3.3 V |
| Operating Temperature (Commercial) | 0C to +85C (C7G suffix) |
| Process Technology | TSMC 55 nm embedded flash |
| RoHS 상태 | Compliant |
10M16DCF256C7G 256-fbga (f256), 17 x 17 mm, 1.0 mm pitch 핀 구성 가이드
10M16DCF256C7G(256-fbga (f256), 17 x 17 mm, 1.0 mm pitch 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: 10M16DCF256C7G.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
10M16DCF256C7G 적합 용도: 6 애플리케이션s: Industrial Motor Control, Video Bridging and Image Aggregation, I/O Expansion for Embedded Processors, Portable Medical Device Front-End, Factory Automation and Protocol Bridging, Test and Measurement Front-End.
Industrial Motor Control
The 10M16DCF256C7G is well-suited for industrial motor-control applications because it provides 45 embedded 18x18 multipliers and 16,000 logic elements, which is enough headroom for field-oriented control (FOC), space-vector PWM generation, and resolver/encoder decoding on a single chip. Its two integrated 12-bit 1 MSPS ADCs sample phase currents and bus voltage directly, eliminating an external ADC and reducing BOM cost. The 256-FBGA package gives 178 user I/Os so designers can drive multiple gate-driver stages and isolation barriers from one device. Non-volatile configuration means the drive starts in under 10 ms, which is critical for safety circuits that must reach a known state immediately after power-up.
추천
Video Bridging and Image Aggregation
The 10M16DCF256C7G serves well in video bridging applications where MIPI-CSI2, parallel CMOS, or LVDS streams must be aggregated and re-mapped before reaching an SoC. With 16K LEs and 562 Kbits of block RAM, the device can implement line buffers, color-space converters, and timing generators in parallel without external memory. The 178 GPIO count is sufficient to fan-in multiple camera data lanes plus control signals. Designers can configure the device once from internal flash and never need to boot from a host processor, which simplifies camera-module firmware in mass-production lines.
추천
I/O Expansion for Embedded Processors
Embedded processors often lack the GPIOs, PWM channels, or specialty interfaces required by industrial designs, and the 10M16DCF256C7G fills this gap as a flexible I/O expander. The MAX 10's dual-configuration flash supports in-field firmware updates over SPI or JTAG, allowing designers to add or change peripheral mappings after deployment. With four general-purpose PLLs and multi-voltage I/O banks (1.2 V to 3.3 V), the FPGA can level-shift between a 1.8 V application processor and 3.3 V legacy peripherals on the same board. The 256-FBGA package keeps board area minimal while exposing 178 user I/Os.
추천
Portable Medical Device Front-End
Portable medical devices such as patient monitors, pulse oximeters, and handheld ultrasound probes benefit from the 10M16DCF256C7G's on-chip 12-bit ADC and DSP multiplier count. The two integrated ADCs sample bio-signals directly, while the 45 multipliers execute FIR and FFT filters in real time without offloading to a host CPU. Instant-on from internal flash lets the device reach a known safe state within 10 ms, which is required for medical equipment with strict IEC 60601 startup behavior. The commercial 0C to +85C range suits body-worn and clinical-cart form factors.
추천
Factory Automation and Protocol Bridging
Factory-automation backplanes often mix legacy fieldbuses such as RS-485, CAN, and proprietary serial links with modern Industrial Ethernet. The 10M16DCF256C7G can act as a multi-protocol bridge, running UART, SPI, I2C, and parallel busses concurrently across its 178 GPIOs. Embedded 18x18 multipliers accelerate checksum and CRC computation for deterministic cycle times. Dual-configuration flash supports redundant firmware images, which is valuable for industrial safety systems that must boot even after a partial flash update.
추천
Test and Measurement Front-End
Test-and-measurement instruments require deterministic sampling, parallel DSP, and flexible I/O - all of which the 10M16DCF256C7G delivers. Designers can build digital trigger engines, pattern generators, and signal-conditioning logic on a single device, while the two integrated 12-bit ADCs handle analog front-end sampling. The 178 GPIOs allow direct interfacing with high-channel-count logic analyzers or oscilloscope probes. Non-volatile instant-on boot means the instrument reaches a calibrated state immediately at power-up, reducing warm-up time for production-line testers.
추천
추천 제품 요약
엔지니어링 참조 데이터: 10M16DCF256C7G — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | 10M16DCF256A7G | 10M16DAF256C7G | 10M08DCF256C7G | 10M08DCF256C8G | 10M08DAF256C7G |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 256-FBGA (F256), 17 x 17 mm, 1.0 mm pitch | 256-FBGA (F256) - same | 256-FBGA (F256) - same | 256-FBGA (F256) - same | 256-FBGA (F256) - same | 256-FBGA (F256) - same |
| Logic Elements | 16,000 | 16,000 | 16,000 | 8,000 | 8,000 | 8,000 |
| Embedded Memory | 562 Kbits (42 M9K blocks) | 562 Kbits | 562 Kbits | 378 Kbits | 378 Kbits | 378 Kbits |
| 18x18 Multipliers | 45 | 45 | 45 | 24 | 24 | 24 |
| Maximum User I/Os | 178 | 178 | 178 | 178 | 178 | 178 |
| On-chip ADC | 2 x 12-bit, 1 MSPS | 2 x 12-bit, 1 MSPS | 2 x 12-bit, 1 MSPS | 2 x 12-bit, 1 MSPS | 2 x 12-bit, 1 MSPS | 2 x 12-bit, 1 MSPS |
| Temperature Grade | Commercial 0C to +85C (C7G) | Commercial (A7G) | Commercial (C7G) | Commercial (C7G) | Commercial (C8G) | Commercial (A7G) |
주요 차별점
- Largest MAX 10 with on-chip ADC at 16K LEs (vs 10M08DCF256C7G)
- Non-volatile configuration eliminates external boot PROM (vs 10CL016YF484C8G)
- Integrated 12-bit ADC reduces analog BOM (vs 10M16DAF256C7G)
설계 노트
The 10M16DCF256C7G requires three independent supply rails: a 1.2 V core (VCCINT), a 2.5 V analog supply (VCCA), and a 1.2 V to 3.3 V I/O supply (VCCIO) per bank. Place a 100 nF decoupling capacitor within 2 mm of every VCC pin and bulk 10 uF ceramic capacitors at each supply plane. Inrush current during configuration can briefly exceed 200 mA, so size the 1.2 V regulator for at least 500 mA steady-state capability.
The 256-FBGA package has 1.0 mm ball pitch and a 17 x 17 mm body; route signals on inner layers using micro-via-in-pad technology if available, or escape through staggered outer-layer vias on a 4-layer board with 1 oz copper. Maintain a continuous ground plane directly under the package to provide a low-impedance return path for the 178 GPIO signals and to dissipate the 1.5 W to 2 W typical power dissipation.
A common pitfall is leaving the MSEL[2:0] pins floating - they must be tied to VCCIO or GND to select the correct configuration mode (JTAG, internal flash, or serial). Also, do not forget the CONF_DONE and nSTATUS pull-ups; they require external 10 kohm resistors to VCCIO. Failing to connect these can cause intermittent boot failures that look like silicon defects but are actually configuration-mode errors.
규정 준수 정보
RoHS and REACH compliance per Intel MAX 10 product declaration. The C7G suffix indicates commercial temperature grade and is not AEC-Q100 qualified; automotive users should select the -Q1 suffix variant.
