ADC12D1000RFIUT - 12-Bit 1/2 GSPS RF-Sampling ADC | Texas Instruments
부품 번호: ADC12D1000RFIUT ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $285 | $285.00 |
| 10 | $265 | $2,650.00 |
| 100 | $240 | $24,000.00 |
| 500 | $215 | $107,500.00 |
| 1,000 | $195 | $195,000.00 |
ADC12D1000RFIUT 개요
An RF-sampling ADC (also called a GSPS ADC) is a type of high-speed analog-to-digital converter designed to digitize signals in the first, second, or higher Nyquist zone, allowing direct sampling of modulated RF carriers without an intermediate frequency (IF) stage. Within the broader converter hierarchy, an RF-sampling ADC sits above the kilomsample/sec successive-approximation (SAR) class and above the megasample/sec pipelined class; it is a sub-category of the wider data-converter IC family, which itself belongs to the signal-chain and power-management domain. Eliminating mixers, LO synthesizers, and anti-alias filters reduces BOM cost, board area, and design complexity in radar, electronic warfare, and broadband communication systems.
Key features include folding and interpolating architecture for low-power operation, dual-channel mode with selectable DES (double-edge sampling) mode, integrated input buffer with adjustable full-scale range, and on-chip calibration to maintain linearity across temperature. The ADC supports 1:1 or 1:2 demultiplexed LVDS output modes with synchronized data, clock, and frame signals. According to the manufacturer datasheet, the device achieves excellent SFDR and SNR performance across the full input bandwidth, simplifying wideband receiver signal chains.
Typical applications include radar and lidar front-end digitizers, broadband satellite and microwave communication receivers, electronic-warfare signal-intelligence systems, test-and-measurement digitizers and oscilloscopes, and software-defined radio (SDR) baseband digitizers. Designers should note that 1.0/2.0 GSPS operation requires very careful PCB layout for the analog inputs, clock, and LVDS outputs to preserve the rated ENOB and SFDR.
드롭인 대체품: ADC12D1000RFIUT — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ADC12D1600RFIUT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC12D500RFIUT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC12D1000CIUT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC12D1000RFIUT/NOPB
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ADC12D1000RFIUT 최대 정격 & 전기적 특성
| 분해능 | 12 bit |
| Number of Channels | 2 |
| Sampling Rate (Dual Mode) | 1.0 GSPS per channel |
| Sampling Rate (Single Mode) | 2.0 GSPS |
| Architecture | Folding and Interpolating |
| Input Frequency Range | Up to and above 2.7 GHz |
| Output Interface | LVDS (IEEE 1596.3-1996 compatible) |
| Output Mode | 1:1 or 1:2 Demultiplexed |
| 동작 온도 범위 | -40C to +85C (industrial) |
| 패키지 | 292-BGA (27 x 27 mm), thermally enhanced |
| Package Code | HBGA |
| 실장 유형 | Surface Mount |
| Lead-Free | Yes |
| RoHS 상태 | Compliant |
ADC12D1000RFIUT hbga 핀 구성 가이드
ADC12D1000RFIUT(hbga 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ADC12D1000RFIUT.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ADC12D1000RFIUT 적합 용도: 6 애플리케이션s: Phased-Array Radar Front-End Digitizer, Electronic Warfare / Signal Intelligence Receiver, Broadband Microwave / Satellite Communications Receiver, High-End Oscilloscope and Digitizer, Software-Defined Radio (SDR) Baseband Digitizer, Lidar and Time-of-Flight Signal Acquisition.
Phased-Array Radar Front-End Digitizer
The ADC12D1000RFIUT's dual 1.0 GSPS sample rate per channel and ability to digitize RF signals above 2.7 GHz make it an excellent match for phased-array and pulsed-radar front ends. Each of the two channels can capture the in-phase (I) and quadrature (Q) baseband outputs from a dual-mixer stage, or two independent antenna channels in a sub-array. With folding-and-interpolating architecture, the part consumes less power than flash ADCs of comparable speed, helping thermal budgets in densely populated antenna electronics units (AEUs). Designers typically pair the ADC with an FPGA such as a Xilinx Kintex or Zynq UltraScale+ for real-time digital beamforming. The BGA package's thermal pad supports continuous 1.0 GSPS operation with proper PCB thermal design.
추천
Electronic Warfare / Signal Intelligence Receiver
For electronic-warfare (EW) and signals-intelligence (SIGINT) receivers, the ADC12D1000RFIUT's 2.7 GHz-plus input bandwidth enables direct digitization of RF environments without analog downconversion, eliminating mixers, local oscillators, and image-reject filters from the signal chain. In single-channel mode the device delivers 2.0 GSPS, providing an instantaneous bandwidth approaching 1 GHz that allows capture and analysis of modern wideband communications and radar threats. Its LVDS outputs with programmable common-mode voltage simplify interface to FPGA-based channelizers. EW systems benefit from the part's wide temperature range and robust BGA package designed for harsh-environment military platforms.
추천
Broadband Microwave / Satellite Communications Receiver
Microwave and satellite-communications receivers operating in L-band, S-band, C-band, and above benefit from the ADC12D1000RFIUT's direct-RF sampling. By sampling at 1.0/2.0 GSPS, the device captures wideband satellite transponder signals or full Ku-/Ka-band downconverted blocks without intermediate analog stages, reducing BOM cost and improving linearity. The 12-bit resolution delivers adequate dynamic range for QPSK through 64-QAM waveforms in DVB-S2X and similar modern standards. Designers should note that 50-ohm matched analog inputs and careful PCB stackup are essential to preserve SNR at the rated bandwidth.
추천
High-End Oscilloscope and Digitizer
Test-and-measurement digitizers and wideband oscilloscopes leverage the ADC12D1000RFIUT's 1.0/2.0 GSPS capability to capture transient and modulated signals at multi-GHz bandwidth. The dual-channel architecture supports two simultaneous high-speed input channels for time-interleaved or differential acquisitions, while the LVDS 1:2 demux mode enables convenient routing into downstream FPGA memory buffers. Compared with oscilloscope ASICs, the ADC12D1000RFIUT provides a flexible COTS data-acquisition building block for modular instruments from vendors targeting 1 GHz to 2 GHz instantaneous bandwidth.
추천
Software-Defined Radio (SDR) Baseband Digitizer
Software-defined radio platforms benefit from the ADC12D1000RFIUT's combination of high sample rate, wide input bandwidth, and folding-and-interpolating low-power architecture. Whether used to digitize a baseband I/Q pair from a tuner, or to directly sample a low-IF or RF signal chain, the device simplifies receiver designs by eliminating analog mixers and filters. The LVDS output with synchronized clock and frame signals integrates cleanly with Zynq SoCs and Kintex FPGAs running GNU Radio, Open Air Interface, or vendor SDR frameworks. The industrial temperature grade supports outdoor and vehicular SDR deployments.
추천
Lidar and Time-of-Flight Signal Acquisition
Lidar and time-of-flight (ToF) systems use the ADC12D1000RFIUT to digitize high-bandwidth return pulses from pulsed laser diodes or modulated continuous-wave (FMCW) lidar waveforms. The 1.0/2.0 GSPS sample rate preserves fine range resolution and timing accuracy for sub-centimeter ranging, while the dual-channel architecture allows simultaneous capture of reference and measurement paths. The LVDS interface streams data efficiently into Xilinx FPGAs implementing matched-filter, FFT-based, or correlation-based range processing. Designers should pair the ADC with low-jitter sampling-clock PLLs to maximize effective number of bits (ENOB).
추천
추천 제품 요약
엔지니어링 참조 데이터: ADC12D1000RFIUT — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ADC12D1600RFIUT | ADC12D500RFIUT | ADC12D1000CIUT | ADC12D1000RFIUT/NOPB |
|---|---|---|---|---|---|
| Package | 292-BGA (27x27 mm) | 292-BGA (27x27 mm) - same | 292-BGA (27x27 mm) - same | 292-BGA (27x27 mm) - same | 292-BGA (27x27 mm) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Sample Rate (Dual Mode) | 1.0 GSPS | 1.6 GSPS | 500 MSPS | 1.0 GSPS | 1.0 GSPS |
| Sample Rate (Single Mode) | 2.0 GSPS | 3.2 GSPS | 1.0 GSPS | 2.0 GSPS | 2.0 GSPS |
| Input Frequency Range | Up to 2.7 GHz+ | Up to 2.7 GHz+ | Up to 2.7 GHz+ | Up to 2.7 GHz+ | Up to 2.7 GHz+ |
| Temperature Grade | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Commercial (0C to +70C) | Industrial (-40C to +85C) |
| Output Interface | LVDS (IEEE 1596.3-1996) | LVDS (IEEE 1596.3-1996) | LVDS (IEEE 1596.3-1996) | LVDS (IEEE 1596.3-1996) | LVDS (IEEE 1596.3-1996) |
주요 차별점
- Dual-channel 1.0 GSPS per channel / single 2.0 GSPS with single-package flexibility (vs ADC12D500RFIUT)
- Industrial temperature grade -40C to +85C (vs ADC12D1000CIUT)
- Pin-compatible across the ADC12D1600/1000RF family (vs Generic 12-bit GSPS ADCs)
설계 노트
The 292-ball BGA package requires a multi-layer PCB with controlled-impedance 50-ohm traces for the analog inputs and matched-length routing for the LVDS outputs. Use a continuous ground plane beneath the device and stitch vias around the perimeter to minimize EMI and preserve SNR at the rated 2.7 GHz input bandwidth. Reference the manufacturer's evaluation board layout for stackup recommendations.
Sampling-clock jitter directly degrades SNR at high input frequencies. Provide a low-jitter, low-phase-noise clock source (such as a dedicated clock synthesizer or VCO with appropriate filtering) and route the clock input with controlled impedance and minimum length. Estimated: at 2.0 GSPS and 100 fs RMS jitter, the jitter-limited SNR ceiling for a 2.7 GHz input is approximately 49 dB.
At 2.0 GSPS in single-channel mode, the device dissipates significant power through the thermally enhanced BGA. Provide a thermal pad with via array to the opposite PCB ground/power plane to maintain junction temperature below the 85C industrial limit. Inadequate thermal relief is a common cause of SFDR/SNR degradation in field installations.
Do not exceed the absolute maximum analog input power or the device will be permanently damaged. The folding-and-interpolating architecture requires proper input common-mode voltage; consult the datasheet for the recommended input common-mode and termination network. Also ensure the LVDS common-mode voltage is correctly programmed to match the receiver (typically the downstream FPGA bank voltage).
규정 준수 정보
Lead-free BGA, RoHS compliant per TI product page. Not AEC-Q100 qualified (industrial grade only, not automotive). The /NOPB ordering suffix explicitly denotes the lead-free, RoHS-compliant variant.
