STMicroelectronics

LM239QT - Low-Power Quad Comparator | STMicroelectronics

MPN: LM239QT ✓ Active
Single supply or split supply Vdss 1.1 mA Id 16-QFN, 3 x 3 mm, 0.50 mm pitch Package
MOQ: 1 |

LM239QT Overview

The STMicroelectronics LM239QT is a low-power quad voltage comparator containing four independent precision comparators in a 16-QFN package measuring 3 x 3 mm. The device operates from a single supply over a wide voltage range or from split supplies, and the LM239 family is specified for supply voltages up to ±18 V.

A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. This is the basic role of the LM239QT within the wider semiconductor and analog IC hierarchy: comparator → analog comparator → signal-conditioning IC → semiconductor. Its four independent channels allow multiple threshold, window, or protection decisions within one package.

The principal characteristics include a supply current of 1.1 mA and a typical low input bias current of 25 nA. These values suit battery-operated and low-power monitoring systems where comparator current and input loading influence the overall power budget. The open-collector outputs can also interface with wired logic systems, although pull-up components are required for normal high-level output operation.

Each comparator channel has independent inputs and an independently controlled open-collector output. Operation from split power supplies allows the input common-mode range to be positioned around ground in bipolar systems, while single-supply operation supports battery and rail-referenced sensing. The device family is intended for general-purpose precision comparison rather than high-speed comparator applications.

Typical uses include battery-cell threshold monitoring, power-supply sequencing, sensor signal conditioning, overvoltage and undervoltage detection, industrial control thresholds, and portable instrumentation. The four-channel architecture can reduce package count when a system needs several independent decisions, while keeping input bias and supply demand low.

PCB design should provide a short, low-impedance ground return and place decoupling capacitance close to the supply pins. Because open-collector outputs require an external pull-up, calculate its resistance against the output sink current and propagation-delay requirements. Do not assume that the output enters a valid logic-high state before the pull-up network is installed.

This product page organizes the LM239QT specifications, qualified alternatives, application guidance, comparison parameters, and design considerations into a practical engineering reference. Use the manufacturer datasheet for the authoritative pin description, ordering information, absolute maximum ratings, and electrical test conditions.

Drop-in alternatives for LM239QT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

LM239AQT

✅ Drop-In ⚠️ Specs Unverified
📦 16-QFN (3x3)
A-version offset-voltage grade differs from standard LM239; the manufacturer identifies offset voltage as low as 2 mV maximum for LM239A, while the standard LM239QT limit requires separate confirmation.

📋 Reference alternative (not in catalog)

LM239QT Maximum Ratings & Electrical Characteristics

Comparator Count 4 independent comparators
Comparator Type Low-power precision voltage comparator
Supply Configuration Single supply or split supply
Maximum Supply Voltage ±18 V
Supply Current 1.1 mA
Input Bias Current 25 nA typical
Logic Output Open-collector
Output Interface Compatibility TTL, MOS, CMOS, DTL, and ECL
Operating Temperature Range -40°C to +105°C
Package 16-QFN, 3 x 3 mm, 0.50 mm pitch
Mounting Type Surface mount
RoHS Status Compliant

LM239QT 16-qfn, 3 x 3 mm, 0.50 mm pitch Pin Configuration Guide

Pin configuration for LM239QT (16-qfn, 3 x 3 mm, 0.50 mm pitch package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

16-qfn, 3 x 3 mm, 0.50 mm pitch package pinout diagram for LM239QT

No detailed pinout data available for LM239QT.

Refer to the datasheet for full pin configuration.

Typical Applications

LM239QT is suitable for 6 applications: Battery Threshold Monitoring, Power-Supply Sequencing, Industrial Sensor Conditioning, Portable Instrument Protection, Sensor Signal Switching, Automotive Electrical Monitoring.

🔋

Battery Threshold Monitoring

The LM239QT is suitable for monitoring several battery-related thresholds because it combines four independent comparators with a supply current of 1.1 mA and a typical input bias current of 25 nA. Multiple channels can indicate charge, discharge, or overvoltage events without requiring four separate packages. The low input loading helps preserve accuracy when the source impedance is high. Because the outputs are open-collector, use a suitable pull-up on each node and account for the resulting logic rise time. The device can also operate from split supplies, which is useful when sensing battery rails around ground.

⚡

Power-Supply Sequencing

The LM239QT can monitor several supply rails in a sequencing or fault-detection circuit by assigning one of its four comparator channels to each threshold. Its single- and split-supply operating capability supports both rail-referenced and ground-centered designs, while the open-collector outputs can pull wired-enable or fault lines low. External pull-ups establish the inactive-high state and should be selected according to sink-current and timing requirements. Because response speed and output propagation delay are not stated in the product source, timing-critical sequencing loops must be checked against the manufacturer electrical characteristics.

🏭

Industrial Sensor Conditioning

The LM239QT is appropriate for industrial sensor interfaces that require converting a slowly varying analog level into a logic decision. Its typical 25 nA input bias current minimizes loading of high-impedance sensor networks, and the 1.1 mA supply current supports low-power sensing nodes. Four independent channels can handle upper and lower limits, alarm points, or multiple sensor inputs within one package. Keep comparator traces away from switching nodes, provide a low-impedance ground return, and use the open-collector outputs with pull-up networks matched to the digital receiver.

📱

Portable Instrument Protection

The LM239QT can implement overvoltage, undervoltage, and other protective decisions in portable measurement equipment. Its low 1.1 mA supply current reduces continuous overhead, and the compact 16-QFN package preserves board area in handheld systems. The four channels may monitor different rails or independent sensor limits, with open-collector outputs driving enable, shutdown, or fault inputs. Because the device is not optimized as a high-speed comparator, it is better suited to slow protection thresholds than to waveform timing or zero-crossing detection.

🧩

Sensor Signal Switching

The LM239QT can compare a sensor-derived voltage against a reference and control whether an analog signal path is enabled or disabled. The low typical input bias of 25 nA is valuable when the divider or sensor output has high impedance, while split-supply operation allows sensing signals around 0 V. Each open-collector channel requires a pull-up and should not be assumed to source current. PCB placement should keep the comparator input path compact and route the pull-up return current away from sensitive analog nodes to reduce switching-related disturbance.

🚗

Automotive Electrical Monitoring

The LM239QT can be evaluated for non-safety-critical electrical monitoring functions such as rail-state detection or diagnostic thresholding in automotive systems. Its wide supply capability, split-supply operation, and four independent channels make it adaptable to multi-rail test circuits. However, the manufacturer source does not identify this ordering code as AEC-Q100 qualified, so it should not be treated as an automotive-qualified substitute without separate qualification. Any deployment also requires review of transient immunity, output timing, and temperature-specific limits in the authoritative datasheet.

What is the LM239QT?
The LM239QT is a low-power quad voltage comparator from STMicroelectronics with four independent precision comparator channels. According to the manufacturer datasheet, the LM239 family supports single-supply or split-supply operation, features open-collector outputs, and is offered in this ordering code as a 16-QFN package measuring 3 x 3 mm.
What are the key specifications of LM239QT that engineers should know?
The LM239QT provides four independent comparators, a supply current of 1.1 mA, and a typical input bias current of 25 nA. Its 16-QFN package measures 3 x 3 mm with a 0.50 mm pitch, while its open-collector outputs support TTL, MOS, CMOS, DTL, and ECL interfaces. According to the STMicroelectronics datasheet, operation is possible from a single supply up to ±18 V or from split supplies.
How many comparators are inside an LM239QT?
The LM239QT contains four independent precision voltage comparators. Each channel has its own input comparison function and open-collector output, allowing four unrelated threshold decisions to be implemented in one package. According to the STMicroelectronics LM239 datasheet, the independent channels make the device suitable for multi-level sensing, window detection, and power-sequencing functions.
What supply voltage range does the LM239QT support?
The LM239QT supports single-supply operation over a wide voltage range and also operates from split supplies. The manufacturer datasheet identifies ±18 V as the stated maximum supply-voltage capability for the LM239 family. The precise minimum single-supply voltage and detailed common-mode limits should be checked in the datasheet's electrical-characteristics table before setting the system rails.
Can LM239QT operate from split power supplies?
Yes, the LM239QT can operate from split power supplies as well as a single supply. This flexibility allows a bipolar or ground-referenced sensing system to compare input voltages around 0 V without changing the basic comparator function. According to the STMicroelectronics datasheet, split-supply operation is an explicit feature of the LM239 family.
What is the input bias current of LM239QT?
The LM239QT has a typical input bias current of 25 nA. This low value helps minimize disturbance of high-impedance sensor nodes and supports low-power threshold-detection designs. The manufacturer datasheet lists the 25 nA figure as a typical characteristic; designers should also review the maximum-value conditions, input bias behavior, and temperature dependency in the full electrical table.
How much supply current does the LM239QT consume?
The LM239QT supply current is specified as 1.1 mA. The figure is important when the comparator monitors a battery-powered system because the load current contributes continuously to the standby budget. According to the STMicroelectronics datasheet, the 1.1 mA characteristic applies across the family's specified supply-voltage conditions, subject to the stated test conditions.
Why does the LM239QT output need a pull-up resistor?
The LM239QT uses an open-collector output, so the device can pull the output low but cannot actively drive it high. An external pull-up resistor establishes the high logic state when the transistor is off. Choose the resistor to balance the required sink current, available rise time, and power dissipation, and confirm that the resulting logic levels are compatible with the following TTL, MOS, or CMOS device.
Where can I download the LM239QT datasheet PDF?
The authoritative LM239QT datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/lm239.pdf. Use the manufacturer document for the complete pin description, electrical characteristics, absolute maximum ratings, typical application circuit, and ordering information. The PDF is also linked through the product page at https://www.st.com/en/amplifiers-and-comparators/lm239.html.
Where can I find the LM239QT pinout?
Use the pin-configuration drawing in the STMicroelectronics LM239 manufacturer datasheet for the authoritative LM239QT pinout. The component is a 16-QFN package, and its exposed-pad and signal assignments must be matched exactly to that drawing during PCB layout. The LM239QT product page at https://www.st.com/en/amplifiers-and-comparators/lm239.html provides access to the associated technical documentation.
Where can I buy LM239QT online?
The LM239QT can be requested through the Request a Quote form on this product page. The form accepts the exact STMicroelectronics ordering code and lets you request current availability, lead time, and commercial terms without relying on a stale marketplace listing. Package and shipment requirements should be confirmed during the quotation response.
What is the price of LM239QT?
Current LM239QT pricing is available through the Request a Quote form on this page. Use that form for the exact 16-QFN ordering code so the quotation reflects the required quantity and delivery terms. Prices can vary with order volume, lifecycle conditions, and packaging, so a current quote is more reliable than a static historical amount.
What is the lead time for LM239QT?
The current LM239QT lead time should be requested through the Request a Quote form on this product page. The manufacturer datasheet defines electrical behavior rather than live inventory or delivery commitments. A quotation response can confirm available stock, manufacturing lead time, and the MOQ for the required quantity and shipment destination.
Is LM239QT in stock?
Current LM239QT inventory should be confirmed through the Request a Quote form on this page. Distributor search listings can change without notice, so live stock should be established for the exact MPN and package. The quotation process also helps distinguish immediately available material from material requiring manufacturer allocation or production scheduling.
What is the best drop-in replacement for LM239QT?
The closest supported same-package choice identified for the LM239QT is the STMicroelectronics LM239AQT, which uses the same 16-QFN footprint but is associated with the A-version offset-voltage grade. Confirm pin compatibility and electrical limits against the manufacturer datasheet before substitution. No cross-brand, 16-QFN drop-in replacement with sufficient technical confirmation was established, so PCB or component substitutions should not be assumed.
What can replace LM239QT without changing the PCB?
The STMicroelectronics LM239AQT is the identified same-footprint alternative for a redesign review because it retains the 16-QFN package and belongs to the same LM239 comparator family. Its offset-voltage grade differs from the standard LM239 specification, so review the exact A-version characteristics and test conditions. When an exact drop-in cannot be confirmed, request a manufacturer-supported quotation for the original MPN instead of changing the footprint.
LM239QT versus LM239AQT: which is better for precision sensing?
The LM239AQT is the better candidate when the application specifically requires the LM239 family's A-version offset-voltage grade, which the manufacturer identifies as capable of an offset specification as low as 2 mV maximum. The standard LM239QT remains appropriate when its own specified offset limits meet the application. Compare the complete input, output, and temperature characteristics rather than using the A-version headline value for the standard part.
When should I choose LM239QT over another quad comparator?
Choose the LM239QT when the design needs four independent low-power comparison channels, an open-collector interface, and operation from a single or split supply. Its 1.1 mA supply current and typical 25 nA input bias current support compact, low-power sensing systems, while the 16-QFN package reduces board area. Choose another qualified part only after confirming output polarity, logic compatibility, speed, and exact pinout requirements.

Engineering reference data for LM239QT — comparison, design guidance, and compliance information.

Selection Guide

Choose the LM239QT when a design requires four independent, low-power threshold comparisons in one 16-QFN package, particularly for battery monitoring, power-rail supervision, industrial sensing, or portable protection. Its 1.1 mA supply current and 25 nA typical input bias current make it appropriate for low-power systems with high-impedance sensor nodes, while open-collector outputs support wired logic and pull-up-based fault signaling. Select LM239AQT when the A-version offset-voltage grade is specifically justified and its exact electrical limits meet the design. Consider TS972IQT or TS974IDT when a single-comparator package is preferable, but account for the reduced channel count in a multi-threshold design. Because only one technically supportable same-package replacement was established, use the Request a Quote form for the exact LM239QT when continuity or traceability is essential.

Comparison with Alternatives

Parameter This Product LM239AQT
Package 16-QFN (3x3) 16-QFN (3x3)
Brand STMicroelectronics STMicroelectronics
Comparator Count 4 independent comparators 4 independent comparators
Supply Current 1.1 mA 1.1 mA
Input Bias Current 25 nA typical 25 nA typical
Maximum Supply Voltage ±18 V ±18 V
Logic Output Open-collector Open-collector

Key Differentiators

  • Four independent precision comparison channels in one compact package (vs TS972IQT)
  • Low typical input bias current for high-impedance sensing (vs TS972IQT)
  • Single- and split-supply operating capability (vs LM239AQT)
  • Open-collector output supports wired-interface integration (vs TS972IQT)

Design Notes

Place the LM239QT decoupling capacitor as close as practical to the supply and ground pins, and provide a low-impedance ground plane connection. The 16-QFN uses a 0.50 mm pitch, so verify the PCB land pattern, pin-1 orientation, and exposed-pad connection against the manufacturer package drawing before release. Keep comparator input traces short and route them away from switching-node copper to reduce displacement current and false threshold transitions.

Design each open-collector output with an external pull-up resistor. Select the resistance using the minimum required high-level current, the output transistor's allowed sink current, the receiver's input-current requirement, and the maximum permitted rise time. The pull-up also forms a capacitive discharge path with PCB and wiring capacitance, so a faster edge generally requires a lower resistance while increasing static current when the output is low.

Do not assign the 2 mV maximum offset figure to the standard LM239QT; the manufacturer identifies that value specifically for LM239A and related A-version devices. Compare the standard and A versions using their own complete electrical tables. Also avoid assuming that an open-collector output can source a logic-high signal, and confirm common-mode limits, output timing, and absolute maximum ratings before finalizing the analog input network.

For high-impedance sensors, minimize leakage through the divider and input nodes because the typical input bias current is 25 nA. Guard or shield sensitive inputs where practical, clean connector and PCB surfaces, and keep the pull-up current path separate from the analog return. When an input crosses a threshold rapidly, account for propagation delay and output rise time instead of assuming an instantaneous decision.

Compliance Information

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

RoHS-compliant construction is identified in the product source. The other compliance attributes are not stated and remain unknown.

Related Searches

LM239QT datasheet LM239QT pinout LM239QT datasheet pdf LM239QT specifications LM239QT QFN-16 LM239QT equivalent LM239QT replacement LM239QT cross reference LM239QT vs LM239AQT LM239QT application circuit LM239QT price LM239QT stock STMicroelectronics LM239QT LM239QT open collector output LM239QT battery threshold monitoring

Related Components & Terms

STMicroelectronics LM239QT LM239AQT TS972IQT TS974IDT voltage comparator analog comparator precision comparator quad comparator semiconductor analog integrated circuit open-collector output single-supply operation split-supply operation supply current input bias current offset voltage 16-QFN QFN family surface-mount package battery monitoring power-supply sequencing industrial sensor conditioning RoHS TTL MOS CMOS
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details