TS932BIN - Dual 20uA Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS932BIN ✓ ActiveTS932BIN Overview
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The broader hierarchy is operational amplifier -> analog amplifier IC -> integrated circuit. The TS932BIN belongs to the micropower operational-amplifier family, where low quiescent current and rail-to-rail output capability are the principal selection criteria. Its dual-channel configuration also reduces component count when two independent gain stages are required.
Key electrical characteristics include a 2.7 V to 10 V operating supply, approximately 20 uA supply current per channel, up to 5 mA output current per channel, 1 pA input-bias current, and 55 dB nominal gain-bandwidth information. The device also supports rail-to-rail output operation and is specified for low-voltage applications. These characteristics make it appropriate for portable measurement, current sensing, and sensor-conditioning circuits where a conventional high-current amplifier would consume unnecessary power.
The TS932BIN uses a rail-to-rail output architecture rather than relying exclusively on conventional source or sink output stages. This allows output signals to approach both supply rails more closely, improving usable dynamic range in low-voltage systems. Because it is a dual amplifier, both channels share the same supply pins while retaining independent input and output connections. Engineering designs must still account for common-mode-range limits, output-current limits, input-bias-current effects, and the voltage drop needed to drive the connected load.
Typical applications include battery-powered sensor interfaces, portable instrumentation, low-current transducers, industrial control signals, and general dual-stage analog signal conditioning. Two amplifiers can be used for independent amplifier, buffer, comparator, or active-filter functions. For precision measurement systems, the circuit designer should verify input offset voltage, common-mode rejection, noise, and bias-current error against the complete signal-chain requirements rather than treating the amplifier as an ideal component.
A practical design consideration is to bypass each supply pin close to the device with local ceramic decoupling and route analog inputs away from switching-current paths. The operating range of 2.7 V to 10 V leaves design margin for both low-voltage portable systems and higher-voltage industrial rails. Output loading and feedback-network values should be checked against the 5 mA per-channel output-current capability.
This page combines the TS932BIN electrical characteristics, package information, pin assignment, engineering alternatives, comparison parameters, and application guidance into a selection reference for dual micropower operational-amplifier designs.
Drop-in alternatives for TS932BIN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with TS932BIN (same form factor and footprint) — differing in Amplifier Type, Input Bias Current, Mounting Type, Package.
TS932ID
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →TS932BID
✅ Drop-In📋 Reference alternative (not in catalog)
TS932IJ
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
TS932BIN Maximum Ratings & Electrical Characteristics
| Number of Amplifiers | 2 channels |
| Amplifier Type | General-purpose operational amplifier |
| Output Type | Rail-to-rail |
| Supply Voltage Range | 2.7 V to 10 V |
| Supply Current per Channel | 20 uA |
| Output Current per Channel | 5 mA |
| Input Bias Current | 1 pA |
| Nominal Gain-Bandwidth | 55 dB |
| Maximum Input Offset Voltage | 2 mV |
| Nominal Common-Mode Rejection Ratio | 85 dB |
| Operating Temperature Range | -40 C to +85 C |
| Package | 8-DIP, 7.62 mm row spacing |
| Pin Count | 8 pins |
| Mounting Type | Through-hole |
| Technology | BiCMOS |
| Primary Application | Low-voltage instrumentation |
| Power Consumption Class | Micropower |
| RoHS Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_qualified |
TS932BIN Pin Configuration
| Pin 1 | OUT1 — Output of amplifier channel 1 |
| Pin 2 | IN1- — Inverting input of amplifier channel 1 |
| Pin 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Pin 6 | IN2- — Inverting input of amplifier channel 2 |
| Pin 7 | OUT2 — Output of amplifier channel 2 |
| Pin 8 | V+ — Positive supply connection |
Typical Applications
TS932BIN is suitable for 6 applications: Battery-Powered Sensor Interface, Portable Instrumentation Amplification, Low-Power Transducer Conditioning, Industrial Control Signal Buffering, Active Filtering and Gain Stage, Low-Voltage Data Acquisition.
Battery-Powered Sensor Interface
The TS932BIN is well matched to battery-powered sensor interfaces because each amplifier channel consumes approximately 20 uA across the 2.7 V to 10 V supply range. Two independent channels can condition signals from two low-power sensors without requiring a separate package for each stage. The rail-to-rail output stage provides additional signal range in low-voltage systems, while the listed 1 pA input-bias current helps minimize loading on high-impedance sensors. Designers should still verify the actual common-mode range, noise performance, and sensor source impedance at the selected operating voltage.
Recommended
Portable Instrumentation Amplification
The TS932BIN supports portable instrumentation designs that require low supply current and flexible output range. Its dual-channel architecture can implement two noninverting gain stages, two buffers, or a mixed signal-conditioning arrangement. With a 2.7 V minimum supply and rail-to-rail output, the device can operate from compact battery-derived rails while preserving useful output headroom. For low-level measurement channels, verify the 2 mV maximum input offset voltage and 85 dB nominal CMRR against the required accuracy and common-mode environment.
Recommended
Low-Power Transducer Conditioning
The TS932BIN is suitable for conditioning outputs from low-power transducers because its 1 pA listed input bias current reduces the loading imposed on high-impedance sources. The dual circuit can amplify one transducer channel and buffer another, or combine two gain stages in a differential measurement arrangement. Its 20 uA per-channel supply current is valuable when the transducer and signal chain must operate from a small energy budget. Feedback resistors should be selected to obtain the required gain while keeping output loading within the 5 mA per-channel capability.
Recommended
Industrial Control Signal Buffering
The TS932BIN can buffer low-level industrial control signals when the design operates within its 2.7 V to 10 V range and -40 C to +85 C temperature interval. Rail-to-rail output helps preserve signal range at low supply voltages, while the dual package provides a compact way to condition two related channels. For factory equipment, place the device away from high-current switching nodes, maintain local supply decoupling, and confirm that the selected protection network does not introduce excessive leakage into the high-impedance input stage.
Recommended
Active Filtering and Gain Stage
The TS932BIN can implement active filters and moderate-bandwidth gain stages when the signal bandwidth is within the amplifier's stated capability. The dual architecture allows a two-stage filter or separate gain and buffer channels without increasing the package count. Rail-to-rail output operation is useful when the filter must operate close to a low-voltage rail, while 20 uA per channel supports compact, low-power analog modules. Component tolerances and the amplifier's finite gain-bandwidth should be included in the frequency-response and stability analysis.
Recommended
Low-Voltage Data Acquisition
The TS932BIN is appropriate for compact data-acquisition front ends that need two low-power analog channels. It can buffer an ADC input, amplify a sensor signal, or provide separate channels for sampling multiple low-voltage measurements. The 2.7 V to 10 V supply range supports common low-voltage rails, and the listed 2 mV maximum input offset voltage should be included in the acquisition-error budget. Place the amplifiers close to the signal source when long traces could allow interference to dominate the small input signal.
Recommended
Recommended Products Summary
Engineering reference data for TS932BIN — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TS932ID | TS932BID | TS932IJ |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-DIP | 8-DIP - same | 8-DIP - same | 8-DIP - same |
| Number of Amplifiers | 2 channels | 2 channels | 2 channels | 2 channels |
| Supply Voltage Range | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V |
| Supply Current per Channel | 20 uA | 20 uA | 20 uA | 20 uA |
| Output Current per Channel | 5 mA | 5 mA | 5 mA | 5 mA |
| Output Type | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Maximum Input Offset Voltage | 2 mV | 2 mV | 2 mV | 2 mV |
| Nominal Common-Mode Rejection Ratio | 85 dB | 85 dB | 85 dB | 85 dB |
Key Differentiators
- Lower power than a conventional dual general-purpose amplifier (vs LM2902N/PB)
- Rail-to-rail output improves low-voltage signal range (vs LM2902N/PB)
- Direct same-family temperature-grade options (vs TS932BIN)
Design Notes
Use local ceramic decoupling at the V+ and V- pins, with the shortest possible ground return from pin 4. The TS932BIN is specified at approximately 20 uA per channel, so supply leakage, input-protection leakage, and resistor loading can become significant in high-impedance battery-powered designs. Calculate the total circuit current rather than relying only on the amplifier specification, and ensure the source can support the maximum channel current over the full 2.7 V to 10 V supply range.
Keep the two amplifier channels away from switching nodes and high-current return paths because the TS932BIN is intended for low-level signal conditioning. Place input components close to pins 2, 3, 5, and 6, and route feedback traces away from the output traces at pins 1 and 7. For an 8-DIP design, check the notch orientation and pin-1 marking during PCB layout and assembly documentation.
Do not treat rail-to-rail output as permission to exceed the output-current or absolute-maximum limits. The listed output capability is 5 mA per channel, and the accepted supply range is 2.7 V to 10 V. Verify load current, output swing, input common-mode limits, and temperature derating. When using TS932ID or TS932IJ instead of TS932BIN, update the PCB documentation and production test limits to match the selected temperature grade.
Compliance Information
The manufacturer documentation identifies the TS932BIN as a general-purpose instrumentation operational amplifier, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code.