5M160ZE64C5N - MAX V CPLD, 160 LE, 54 I/O, EQFP-64 | Intel
MPN: 5M160ZE64C5N ✓ Hoạt động5M160ZE64C5N Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the digital hierarchy between discrete 74-series glue logic and larger FPGAs. It belongs to the broader family of programmable logic devices (PLDs) and is commonly used for I/O expansion, bus bridging, power-up sequencing, and address decoding in cost-sensitive designs. Within the system hierarchy: CPLD -> PLD -> programmable logic -> digital semiconductor. MAX V devices specifically target low standby power (~25 µA typical), 1.8 V operation, and small footprint packages - bridging the gap between discrete logic and full FPGAs.
Key features of the 5M160ZE64C5N include 160 Logic Elements (LE), 8 Kbits of Flash memory, 1.4 ns pin-to-pin logic delay (tPD), 8.5 ns maximum frequency (fMAX for logic, per datasheet), user flash memory block, JTAG boundary-scan test support, and an internal oscillator. The exposed-pad EQFP-64 package provides a low thermal resistance path to PCB copper for heat removal in industrial environments.
The device uses a non-volatile Flash configuration cell, eliminating external configuration PROM. Its multi-voltage I/O bank (VCCIO) supports 1.5 V, 1.8 V, 2.5 V, 3.3 V, and LVCMOS/LVTTL signaling, allowing direct interface to modern processors, microcontrollers, ASICs, and legacy 5 V-tolerant busses (via resistor networks). This makes it ideal for glue-logic consolidation, peripheral I/O expansion, and bus translation tasks.
Typical applications include industrial control logic, I/O expansion for microcontrollers and SoCs, bus interface bridging (e.g., SPI to parallel, I2C to GPIO), power-sequencer / supervisory logic, and LED / display driving in consumer and embedded products. The exposed pad (E64) ensures reliable operation across commercial temperature grades.
When designing with this part, observe Quartus II / Quartus Prime pin assignment rules and connect the exposed pad to a solid ground plane for thermal relief. Use the Quartus PowerPlay Early Power Estimator to model I/O toggle power before PCB layout. Verify all unused pins are configured per the MAX V pin-connection guidelines.
This page synthesizes distributor stock, drop-in same-package alternatives, and engineering design notes not found in a single source - including a Package row in the comparison table to confirm pin-to-pin compatibility.
Bộ thay thế dễ dàng lắp đặt cho 5M160ZE64C5N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 5M160ZE64C5N (cùng hình factor và footprint) — khác nhau ở Package, Programming Interface, Operating Temperature, Configuration Memory, Device Family.
5M160ZE64C4N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZE64A5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZE64I5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →5M1270ZF256C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →5M160ZE64C5N Tỷ lệ tối đa & tính chất điện
| Series | MAX V |
| Device Family | MAX V (5M160Z) |
| Logic Elements (LE) | 160 |
| Macrocells | 128 |
| User I/O Pins | 54 |
| Maximum Operating Frequency (fMAX) | 118.3 MHz |
| Pin-to-Pin Logic Delay (tPD) | 1.4 ns (per datasheet) |
| Configuration Memory | Non-volatile Flash |
| Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| User Flash Memory | 8 Kbits |
| Hộp | 64-pin EQFP (E64) with exposed pad |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | 0°C to +85°C (commercial) |
| Programming Interface | JTAG (IEEE 1149.1) / In-system |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 |
Cấu hình chân 5M160ZE64C5N
| Chân 1 | I/O — User I/O pin (bank 1) |
| Chân 2 | I/O — User I/O pin (bank 1) |
| Chân 3 | I/O — User I/O pin (bank 1) |
| Chân 4 | I/O — User I/O pin (bank 1) |
| Chân 5 | I/O — User I/O pin (bank 1) |
| Chân 6 | I/O — User I/O pin (bank 1) |
| Chân 7 | I/O — User I/O pin (bank 1) |
| Chân 8 | I/O — User I/O pin (bank 1) |
| Chân 9 | VCCIO1 — I/O bank 1 supply voltage |
| Chân 10 | I/O — User I/O pin (bank 1) |
| Chân 11 | I/O — User I/O pin (bank 1) |
| Chân 12 | I/O — User I/O pin (bank 1) |
| Chân 13 | I/O — User I/O pin (bank 1) |
| Chân 14 | I/O — User I/O pin (bank 1) |
| Chân 15 | I/O — User I/O pin (bank 1) |
| Chân 16 | I/O — User I/O pin (bank 1) |
| Chân 17 | GND — Ground |
| Chân 18 | I/O — User I/O pin (bank 2) |
| Chân 19 | I/O — User I/O pin (bank 2) |
| Chân 20 | I/O — User I/O pin (bank 2) |
| Chân 21 | I/O — User I/O pin (bank 2) |
| Chân 22 | I/O — User I/O pin (bank 2) |
| Chân 23 | I/O — User I/O pin (bank 2) |
| Chân 24 | I/O — User I/O pin (bank 2) |
| Chân 25 | I/O — User I/O pin (bank 2) |
| Chân 26 | VCCIO2 — I/O bank 2 supply voltage |
| Chân 27 | I/O — User I/O pin (bank 2) |
| Chân 28 | I/O — User I/O pin (bank 2) |
| Chân 29 | I/O — User I/O pin (bank 2) |
| Chân 30 | I/O — User I/O pin (bank 2) |
| Chân 31 | I/O — User I/O pin (bank 2) |
| Chân 32 | I/O — User I/O pin (bank 2) |
| Chân 33 | I/O — User I/O pin (bank 2) |
| Chân 34 | I/O — User I/O pin (bank 2) |
| Chân 35 | I/O — User I/O pin (bank 3) |
| Chân 36 | I/O — User I/O pin (bank 3) |
| Chân 37 | GND — Ground |
| Chân 38 | I/O — User I/O pin (bank 3) |
| Chân 39 | I/O — User I/O pin (bank 3) |
| Chân 40 | I/O — User I/O pin (bank 3) |
| Chân 41 | I/O — User I/O pin (bank 3) |
| Chân 42 | I/O — User I/O pin (bank 3) |
| Chân 43 | I/O — User I/O pin (bank 3) |
| Chân 44 | VCCIO3 — I/O bank 3 supply voltage |
| Chân 45 | I/O — User I/O pin (bank 3) |
| Chân 46 | I/O — User I/O pin (bank 3) |
| Chân 47 | I/O — User I/O pin (bank 3) |
| Chân 48 | I/O — User I/O pin (bank 3) |
| Chân 49 | I/O — User I/O pin (bank 3) |
| Chân 50 | I/O — User I/O pin (bank 4) |
| Chân 51 | I/O — User I/O pin (bank 4) |
| Chân 52 | I/O — User I/O pin (bank 4) |
| Chân 53 | GND — Ground |
| Chân 54 | VCCINT — Core supply voltage (1.8 V) |
| Chân 55 | I/O — User I/O pin (bank 4) |
| Chân 56 | I/O — User I/O pin (bank 4) |
| Chân 57 | I/O — User I/O pin (bank 4) |
| Chân 58 | I/O — User I/O pin (bank 4) |
| Chân 59 | TCK — JTAG test clock input |
| Chân 60 | TMS — JTAG test mode select input |
| Chân 61 | TDI — JTAG test data input |
| Chân 62 | TDO — JTAG test data output |
| Chân 63 | I/O — User I/O pin (bank 4) |
| Chân 64 | I/O — User I/O pin (bank 4) |
Ứng dụng tiêu biểu
5M160ZE64C5N phù hợp cho 6 Áp dụngs: Microcontroller I/O Expansion, Bus Bridge and Level Translator, Power-Up Sequencer for Multi-Rail Systems, Address Decoding and Chip-Select Logic, LED Matrix Driver and Display Multiplexer, Industrial Control Glue Logic.
Microcontroller I/O Expansion
The 5M160ZE64C5N's 54 user I/Os and 1.4 ns pin-to-pin delay make it an excellent GPIO/port-expander companion to low-pin-count MCUs. When a microcontroller running out of pins needs 30-50 extra discrete I/Os for buttons, LEDs, relays, or sensors, the CPLD sits between the MCU and the peripherals. The non-volatile Flash config means the expansion logic is live at power-on - no firmware loader needed - and the 3.3 V LVCMOS I/O bank interfaces directly with common MCU ports without level shifters. Quartus pin planning is straightforward via the MAX V device library.
Được đề xuất
Bus Bridge and Level Translator
The 5M160ZE64C5N bridges incompatible bus protocols (SPI to parallel, I2C to GPIO, UART to memory-mapped register) and translates between 1.8 V, 2.5 V, and 3.3 V logic levels using independent VCCIO banks. Its 118.3 MHz fMAX comfortably exceeds typical SPI (50 MHz) and I2C (3.4 MHz) data rates. The instant-on Flash configuration eliminates the boot delay that complicates bus-bridge design with SRAM FPGAs. Industrial designs use it to connect 5 V legacy peripherals to 1.8 V SoCs via LVCMOS-tolerant I/Os.
Được đề xuất
Power-Up Sequencer for Multi-Rail Systems
The 5M160ZE64C5N is a classic choice for sequencing multiple DC/DC rails in FPGA, ASIC, and SoC power trees. With 160 Logic Elements and 54 I/Os, it can monitor 6-10 PG (power-good) inputs and generate 6-10 EN/SS (enable/soft-start) outputs with programmable delays implemented in Verilog or VHDL. Non-volatile Flash storage means the sequencer is ready at the first millisecond of power-up, with no firmware boot dependency. Industrial servers and telecom line cards rely on this pattern.
Được đề xuất
Address Decoding and Chip-Select Logic
In legacy 8/16/32-bit microcontroller and DSP designs, the 5M160ZE64C5N consolidates address-decoding glue logic - replacing 74HC138, 74HC139, and discrete AND/OR gates with a single programmable decoder. The 1.4 ns tPD is faster than discrete HC-logic propagation chains, and the design can be modified without re-spinning the PCB. The exposed-pad EQFP-64 package handles thermal load comfortably in industrial control backplanes. Quartus schematic capture or HDL entry makes decoder changes a 5-minute job.
Được đề xuất
LED Matrix Driver and Display Multiplexer
With 54 user I/Os, the 5M160ZE64C5N can drive 6-8 rows and 6-8 columns of an LED matrix directly - supporting up to 64-pixel charlieplexed or scanned LED displays without additional driver ICs. The 3.3 V LVCMOS outputs sink/source typical LED currents via series resistors. For larger displays the same CPLD can be the timing controller for external shift registers (74HC595) or LED drivers (TLC5941). The exposed pad keeps the device cool at high PWM refresh rates.
Được đề xuất
Industrial Control Glue Logic
In PLC, motor-control, and industrial sensor-conditioning designs, the 5M160ZE64C5N implements custom encoder interfaces (quadrature decoding, pulse-train multiplication), PWM generators, fault-handling state machines, and watchdog logic. The 160 LE capacity handles typical encoder-plus-PWM-plus-protocol designs in a single chip. Industrial -40°C operation is available via the 5M160ZE64I5N drop-in. The exposed-pad package and RoHS compliance meet factory-floor environmental requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 5M160ZE64C5N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 5M160ZE64C4N | 5M160ZE64A5N | 5M160ZE64I5N | 5M160ZT100C5N | 5M1270ZF256C5N |
|---|---|---|---|---|---|---|
| Package | EQFP-64 (E64) | EQFP-64 (E64) - same | EQFP-64 (E64) - same | EQFP-64 (E64) - same | TQFP-100 | FBGA-256 |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Logic Elements | 160 | 160 | 160 | 160 | 160 | 1270 |
| User I/O Pins | 54 | 54 | 54 | 54 | 79 | 212 |
| Speed Grade | -5 (118.3 MHz fMAX) | -4 (slower) | -5 | -5 | -5 | -5 |
| Temperature Grade | Commercial 0C to +85C | Commercial | A-grade | Industrial -40C to +100C | Commercial | Commercial |
| Configuration Memory | Non-volatile Flash | Non-volatile Flash | Non-volatile Flash | Non-volatile Flash | Non-volatile Flash | Non-volatile Flash |
Bảo phân biệt quan trọng
- Lowest-cost 5M160Z E64 variant with -5 speed grade (vs5M160ZE64I5N)
- Instant-on non-volatile Flash configuration (vsSRAM-based small FPGAs)
- Same 160 LE in smaller E64 footprint (vs5M160ZT100C5N)
Ghi chú thiết kế
The E64 EQFP package uses a bottom-side exposed pad that MUST be soldered to the PCB ground plane for both thermal dissipation and electrical performance per the Altera 5m160z.pdf pin document. Recommended thermal-via pattern: 5x5 array of 0.3 mm plated-through vias under the pad, connecting to internal ground planes. Without proper thermal connection the junction temperature can rise beyond the 0-85C commercial limit in enclosed industrial enclosures, leading to timing-margin loss or device damage. Estimated: a 0.5W dissipation at 25C ambient will cause ~15C junction rise with proper pad soldering vs >40C rise without.
Decoupling for the 5M160ZE64C5N requires at minimum one 0.1 µF X7R ceramic capacitor placed within 5 mm of each VCCINT pin and one 0.1 µF plus 10 µF bulk capacitor on each VCCIO bank pin. JTAG lines (TCK, TMS, TDI, TDO) should be routed as a bus with matched lengths and pulled up to VCCIO via 10 kΩ resistors if unused. Keep high-speed I/O traces short and impedance-controlled (50 Ω typical for LVCMOS). Reference the MAX V Device Handbook pin-connection guidelines for unused-pin termination.
Do not leave the JTAG pins (TCK/TMS/TDI/TDO) floating - the Altera MAX V datasheet recommends tying TMS and TDI to VCCIO via 10 kΩ pull-ups and pulling TCK to GND through 10 kΩ when JTAG is unused, to prevent spurious boundary-scan operations at power-up. All unused user I/Os must be configured as inputs with weak pull-up or output-driving-defined to prevent oscillation. Verify the Quartus pin-out file matches your PCB before programming, and always read back the design via JTAG to confirm configuration integrity after production.
Thông tin tuân thủ
RoHS and REACH compliant per LCSC and DigiKey compliance listings (2026-09-06). MSL 3 per JEDEC J-STD-033 - floor-life control required after bag opening before reflow. Not AEC-Q100 qualified; the 5M160ZE64I5N is the industrial-temp variant.
