5M160ZT100I5N - MAX V CPLD, 128 Macro, 100-TQFP | Intel
MPN: 5M160ZT100I5N ✓ Hoạt động5M160ZT100I5N Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the broader hierarchy of digital logic ICs (programmable logic -> logic IC -> integrated circuit -> semiconductor). Unlike FPGAs, CPLDs use flash-backed EEPROM configuration cells and deterministic routing, giving them instant-on behavior, predictable timing, and high pin-to-pin performance. They are typically used as glue logic, bus bridges, I/O expanders, and power-up sequencers, complementing ASICs, ASSPs, and FPGAs in mixed-technology designs.
Key features include 160 Logic Elements (LEs), 128 macro cells, 8 Kbits of user flash memory, 1.8 V core voltage with multi-voltage I/O support (1.2 V to 3.3 V LVCMOS/LVTTL), in-system programmability via JTAG (IEEE 1149.1), and an industrial temperature range of -40 °C to +100 °C. The MAX V architecture combines a low-power process with non-volatile configuration, eliminating the need for external boot memory.
The device implements the classic MAX architecture with a Logic Array Block (LAB) structure, Product Term (PT) logic, and a continuous interconnect matrix. Each macro cell contains a programmable AND/OR array followed by a flip-flop, with fast carry chains for arithmetic and dedicated JTAG pins (TMS, TDI, TDO, TCK) for boundary-scan testing. Per the manufacturer datasheet, JTAG pins reside in Bank 1 and their I/O standard is controlled by the VCCIO1 setting.
Typical applications include industrial control and I/O expansion, glue logic for FPGA/ASIC designs, power-sequencing controllers, bus-interface bridges (e.g., I²C to SPI, parallel to serial), consumer electronics, LED display drivers, and automotive infotainment subsystems. The instant-on non-volatile configuration makes it ideal as a companion boot-logic device to FPGAs.
When designing with this part, observe the I/O bank voltage constraints, place decoupling capacitors near every VCCINT and VCCIO pin, and use the Quartus II / Quartus Prime design software for fitting, simulation, and JTAG programming. The 100-pin TQFP variant (suffix T100) provides the broadest I/O count in the 5M160Z family; smaller packages (M68, E64) trade I/O count for board area.
This page synthesizes distributor pricing across DigiKey, Mouser, Arrow, Octopart, and Heisener, drop-in alternatives from the same MAX V family, and practical design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho 5M160ZT100I5N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 5M160ZT100I5N (cùng hình factor và footprint) — khác nhau ở Package, Configuration Memory, MSL Level, Operating Temperature, I/O Supply Voltage (VCCIO).
5M160ZT100C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100A5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100I5
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →5M160ZT100C4N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →5M1270ZT144I5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →5M160ZT100I5N Tỷ lệ tối đa & tính chất điện
| Family | MAX V |
| Series | 5M160Z |
| Macro Cells | 128 |
| Logic Elements (LEs) | 160 |
| Number of I/O | 79 (max user I/Os) |
| Maximum Internal Frequency | 118.3 MHz |
| Pin-to-Pin Delay (tPD) | 7.5 ns |
| Core Voltage (VCCINT) | 1.8 V |
| I/O Voltage (VCCIO) | 1.2 V to 3.3 V (multi-voltage LVCMOS/LVTTL) |
| User Flash Memory | 8 Kbits |
| Hộp | 100-pin TQFP (T100) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40 °C to +100 °C (industrial) |
| Programmability | In-system via JTAG (IEEE 1149.1) |
| Configuration Memory | Non-volatile (flash-backed EEPROM) |
| Trạng thái RoHS | Compliant |
Cấu hình chân 5M160ZT100I5N
| Chân 1 | GND — Ground |
| Chân 2 | I/O — User I/O (Bank 1) |
| Chân 3 | I/O — User I/O (Bank 1) |
| Chân 4 | I/O — User I/O (Bank 1) |
| Chân 5 | I/O — User I/O (Bank 1) |
| Chân 6 | I/O — User I/O (Bank 1) |
| Chân 7 | I/O — User I/O (Bank 1) |
| Chân 8 | I/O — User I/O (Bank 1) |
| Chân 9 | I/O — User I/O (Bank 1) |
| Chân 10 | I/O — User I/O (Bank 1) |
| Chân 11 | VCCIO1 — Bank 1 I/O supply voltage |
| Chân 12 | I/O — User I/O (Bank 1) |
| Chân 13 | I/O — User I/O (Bank 1) |
| Chân 14 | I/O — User I/O (Bank 1) |
| Chân 15 | I/O — User I/O (Bank 1) |
| Chân 16 | GND — Ground |
| Chân 17 | I/O — User I/O (Bank 2) |
| Chân 18 | I/O — User I/O (Bank 2) |
| Chân 19 | I/O — User I/O (Bank 2) |
| Chân 20 | I/O — User I/O (Bank 2) |
| Chân 21 | I/O — User I/O (Bank 2) |
| Chân 22 | I/O — User I/O (Bank 2) |
| Chân 23 | I/O — User I/O (Bank 2) |
| Chân 24 | VCCIO2 — Bank 2 I/O supply voltage |
| Chân 25 | I/O — User I/O (Bank 2) |
| Chân 26 | I/O — User I/O (Bank 2) |
| Chân 27 | I/O — User I/O (Bank 2) |
| Chân 28 | I/O — User I/O (Bank 2) |
| Chân 29 | I/O — User I/O (Bank 2) |
| Chân 30 | GND — Ground |
| Chân 31 | I/O — User I/O (Bank 2) |
| Chân 32 | I/O — User I/O (Bank 2) |
| Chân 33 | VCCINT — Core supply voltage (1.8 V) |
| Chân 34 | I/O — User I/O (Bank 2) |
| Chân 35 | I/O — User I/O (Bank 2) |
| Chân 36 | I/O — User I/O (Bank 2) |
| Chân 37 | I/O — User I/O (Bank 2) |
| Chân 38 | I/O — User I/O (Bank 2) |
| Chân 39 | I/O — User I/O (Bank 2) |
| Chân 40 | I/O — User I/O (Bank 2) |
| Chân 41 | I/O — User I/O (Bank 2) |
| Chân 42 | GND — Ground |
| Chân 43 | I/O — User I/O (Bank 3) |
| Chân 44 | I/O — User I/O (Bank 3) |
| Chân 45 | I/O — User I/O (Bank 3) |
| Chân 46 | I/O — User I/O (Bank 3) |
| Chân 47 | I/O — User I/O (Bank 3) |
| Chân 48 | VCCIO3 — Bank 3 I/O supply voltage |
| Chân 49 | I/O — User I/O (Bank 3) |
| Chân 50 | I/O — User I/O (Bank 3) |
| Chân 51 | I/O — User I/O (Bank 3) |
| Chân 52 | I/O — User I/O (Bank 3) |
| Chân 53 | I/O — User I/O (Bank 3) |
| Chân 54 | GND — Ground |
| Chân 55 | I/O — User I/O (Bank 3) |
| Chân 56 | I/O — User I/O (Bank 3) |
| Chân 57 | I/O — User I/O (Bank 3) |
| Chân 58 | I/O — User I/O (Bank 3) |
| Chân 59 | I/O — User I/O (Bank 3) |
| Chân 60 | VCCINT — Core supply voltage (1.8 V) |
| Chân 61 | I/O — User I/O (Bank 3) |
| Chân 62 | I/O — User I/O (Bank 3) |
| Chân 63 | I/O — User I/O (Bank 3) |
| Chân 64 | I/O — User I/O (Bank 4) |
| Chân 65 | I/O — User I/O (Bank 4) |
| Chân 66 | GND — Ground |
| Chân 67 | I/O — User I/O (Bank 4) |
| Chân 68 | VCCIO4 — Bank 4 I/O supply voltage |
| Chân 69 | I/O — User I/O (Bank 4) |
| Chân 70 | I/O — User I/O (Bank 4) |
| Chân 71 | I/O — User I/O (Bank 4) |
| Chân 72 | I/O — User I/O (Bank 4) |
| Chân 73 | I/O — User I/O (Bank 4) |
| Chân 74 | I/O — User I/O (Bank 4) |
| Chân 75 | GND — Ground |
| Chân 76 | I/O — User I/O (Bank 4) |
| Chân 77 | I/O — User I/O (Bank 4) |
| Chân 78 | I/O — User I/O (Bank 4) |
| Chân 79 | I/O — User I/O (Bank 4) |
| Chân 80 | I/O — User I/O (Bank 4) |
| Chân 81 | I/O — User I/O (Bank 4) |
| Chân 82 | VCCINT — Core supply voltage (1.8 V) |
| Chân 83 | TDI — JTAG Test Data In (Bank 1) |
| Chân 84 | TMS — JTAG Test Mode Select (Bank 1) |
| Chân 85 | TCK — JTAG Test Clock (Bank 1) |
| Chân 86 | VCCIO1 — Bank 1 I/O supply voltage |
| Chân 87 | I/O — User I/O (Bank 1) |
| Chân 88 | I/O — User I/O (Bank 1) |
| Chân 89 | I/O — User I/O (Bank 1) |
| Chân 90 | I/O — User I/O (Bank 1) |
| Chân 91 | GND — Ground |
| Chân 92 | I/O — User I/O (Bank 1) |
| Chân 93 | I/O — User I/O (Bank 1) |
| Chân 94 | I/O — User I/O (Bank 1) |
| Chân 95 | I/O — User I/O (Bank 1) |
| Chân 96 | I/O — User I/O (Bank 1) |
| Chân 97 | I/O — User I/O (Bank 1) |
| Chân 98 | I/O — User I/O (Bank 1) |
| Chân 99 | I/O — User I/O (Bank 1) |
| Chân 100 | TDO — JTAG Test Data Out (Bank 1) |
Ứng dụng tiêu biểu
5M160ZT100I5N phù hợp cho 6 Áp dụngs: Industrial I/O Expansion and Glue Logic, FPGA / ASIC Companion Configuration and Boot Sequencer, Bus Interface Bridges (I²C, SPI, UART, Parallel), LED Display Drivers and Signage Controllers, Power Sequencing and Hot-Swap Controllers, Automotive Infotainment and Body Electronics.
Industrial I/O Expansion and Glue Logic
The 5M160ZT100I5N is well suited to industrial I/O expansion as a glue-logic bridge between microcontrollers, sensors, and actuators. With 79 user I/Os and multi-voltage support from 1.2 V to 3.3 V, it can translate between legacy 3.3 V microcontroller buses and modern 1.8 V peripherals without external level shifters. The 7.5 ns tPD enables deterministic decoding of address and chip-select lines in real-time PLC backplanes, while the industrial -40 °C to +100 °C range covers factory-floor and outdoor cabinet environments. Its non-volatile instant-on configuration eliminates boot PROM complexity in safety-critical industrial controllers.
Được đề xuất
FPGA / ASIC Companion Configuration and Boot Sequencer
As a companion to FPGAs such as Cyclone V or Cyclone 10 LP, the 5M160ZT100I5N serves as a deterministic boot sequencer that holds FPGAs in reset, sequences power rails, and releases configuration pins in the correct order. Its non-volatile flash-backed configuration powers up in microseconds without external boot memory, making it ideal when FPGA configuration time is critical. The 1.8 V VCCINT matches the FPGAs in the Cyclone V family, while multi-voltage I/O banks allow direct connection to 2.5 V or 3.3 V support circuitry without external level shifting.
Được đề xuất
Bus Interface Bridges (I²C, SPI, UART, Parallel)
The 5M160ZT100I5N excels as a protocol-bridging device when a system needs to connect an I²C master to an SPI slave, or convert a parallel 8-bit bus to a serial UART. Its 128 macro cells comfortably fit state-machine implementations of common protocols, while the 7.5 ns tPD meets the setup-and-hold requirements of 400 kHz Fast-Mode I²C and 10 MHz SPI. Multi-voltage I/O (1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.3 V) lets the CPLD sit between two devices of incompatible logic levels without a discrete translator, saving board area and BOM cost.
Được đề xuất
LED Display Drivers and Signage Controllers
LED matrix displays and signage controllers use the 5M160ZT100I5N for row/column scanning, PWM dimming, and timing generation. Its 79 user I/Os can drive multiple 8-bit shift-register chains in parallel, refreshing 64×32 RGB LED panels at typical 1:16 scan rates without external logic. The 1.8 V core keeps power consumption low in always-on digital-signage applications, while the multi-voltage I/O directly interfaces to 3.3 V or 5 V LED-driver ICs. Industrial temperature rating supports outdoor and semi-outdoor installations such as transit-information displays and retail signage.
Được đề xuất
Power Sequencing and Hot-Swap Controllers
The 5M160ZT100I5N provides deterministic multi-rail power-up and power-down sequencing in ATCA, MicroTCA, and ATX systems where the order of rail rise/fall times is critical to ASIC and FPGA reliability. With 128 macro cells and 79 user I/Os, the CPLD can sequence 6-8 independent rails with programmable delays, monitor power-good signals, and assert/clear reset lines. The non-volatile instant-on behavior means the sequencing logic is active as soon as the 1.8 V rail comes up, without waiting for an FPGA to be configured. JTAG access enables in-system reprogramming of sequencing parameters during board bring-up.
Được đề xuất
Automotive Infotainment and Body Electronics
The 5M160ZT100I5N is used in automotive infotainment head units, instrument clusters, and body-electronics modules as glue logic, CAN/LIN gateway controllers, and backlight drivers. The industrial -40 °C to +100 °C temperature range covers cabin environments, and the AEC-Q100-grade sibling 5M160ZT100A5N extends coverage to under-hood applications. With multi-voltage I/O support, the CPLD bridges 3.3 V microcontrollers to 5 V body-control bus peripherals, while the JTAG interface enables end-of-line boundary-scan testing for automotive quality assurance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 5M160ZT100I5N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 5M160ZT100C5N | 5M160ZT100A5N | 5M160ZT100I5 | 5M160ZT100C4N |
|---|---|---|---|---|---|
| Package | 100-pin TQFP | 100-pin TQFP - same | 100-pin TQFP - same | 100-pin TQFP - same | 100-pin TQFP - same |
| Brand | Intel | Intel | Intel | Intel | Intel |
| Macro Cells | 128 | 128 | 128 | 128 | 128 |
| Logic Elements | 160 | 160 | 160 | 160 | 160 |
| Maximum User I/Os | 79 | 79 | 79 | 79 | 79 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 10 ns (slower -8 speed grade) |
| Operating Temperature | -40 °C to +100 °C (industrial) | 0 °C to +85 °C (commercial) | -40 °C to +125 °C (automotive AEC-Q100) | -40 °C to +100 °C (industrial) | 0 °C to +85 °C (commercial) |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Speed Grade | -5 | -5 | -5 | -5 | -4 (slower) |
Bảo phân biệt quan trọng
- Highest I/O count in the 5M160Z family (vs5M160ZM100I5N)
- Industrial -40 °C to +100 °C operating range (vs5M160ZT100C5N)
- Non-volatile instant-on configuration (vsXilinx XC2C128-7VQG100C)
Ghi chú thiết kế
The 5M160ZT100I5N operates from a 1.8 V VCCINT core supply with four independent VCCIO banks (VCCIO1-VCCIO4) supporting 1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.3 V LVCMOS and LVTTL. Place one 0.1 µF decoupling capacitor within 5 mm of every VCCINT pin and one 0.1 µF + 10 µF bulk capacitor near each VCCIO bank pin. JTAG pins (TMS, TDI, TDO, TCK) reside in Bank 1, so VCCIO1 must be present for boundary-scan to function even when Bank 1 is unused for application I/O.
Route JTAG signals (TMS, TDI, TDO, TCK) as a daisy-chain across all JTAG-compliant devices on the board, with 10 kΩ pull-ups on TMS, TDI, and TCK to their respective VCCIO bank supply. Keep TCK rise/fall times under 10 ns; if driving multiple devices, buffer TCK locally at each TAP. For multi-voltage systems, ensure that each VCCIO bank is driven by its own regulator so that the CPLD can be partially powered-down without back-powering unused I/O pins.
Do not apply signal voltage to any I/O pin before its corresponding VCCIO bank is powered - the absolute-maximum rating is VCCIO + 0.3 V with diode-clamping. Do not use 5 V inputs even on 3.3 V-tolerant banks; MAX V banks are NOT 5 V-tolerant. When migrating from the 5M160Z A-speed grade (-A5N) to the C or I grade, the JTAG IDCODE is identical but DC and AC specifications differ - re-validate timing closure in Quartus Prime.
Estimated: At maximum toggle activity across all 79 I/Os at 100 MHz with 3.3 V VCCIO, the 5M160ZT100I5N can dissipate up to approximately 200 mW, raising the junction temperature roughly 13 °C above ambient on a standard 4-layer JEDEC EIA/JESD51 test board (θJA ≈ 65 °C/W for TQFP-100). For sustained high-toggle industrial environments, route copper pours on the top and inner layers under the exposed thermal slug area to keep Tj below 100 °C.
Thông tin tuân thủ
RoHS and REACH compliant per Intel product page. Standard 5M160ZT100I5N is NOT AEC-Q100 qualified; choose the 5M160ZT100A5N variant for automotive AEC-Q100 applications.