K9LUGY8J7D-BCK0 - Samsung V-NAND Flash Memory | Samsung
MPN: K9LUGY8J7D-BCK0 ✓ Hoạt độngK9LUGY8J7D-BCK0 Tóm tắt
NAND flash memory is a non-volatile storage technology that retains data without power and forms the storage layer in solid-state drives (SSDs), eMMC/UFS modules, memory cards, and embedded systems. Within the memory hierarchy, NAND flash sits below DRAM as persistent bulk storage; 3D V-NAND stacks memory cells vertically to increase bit density while reducing cell-to-cell interference compared with planar NAND.
The K9LUGY8J7D family is designed for mass-storage applications requiring high capacity per package. Samsung's V-NAND technology improves endurance and write performance through charge-trap flash cells arranged in vertical stacks. Devices in this class interface via a standard ONFI-compliant asynchronous/DDR toggle-mode NAND interface, supporting page-program and block-erase commands managed by a host-side controller with ECC (error correcting code) such as BCH or LDPC.
Typical applications include solid-state drives, eMMC and UFS embedded storage, industrial storage modules, set-top boxes, and networking equipment requiring reliable non-volatile storage.
When designing with high-density V-NAND, the host controller must implement wear leveling, bad-block management, and refresh algorithms, and layout should follow Samsung's signal-integrity guidance for high-speed data lines.
This page synthesizes drop-in family alternatives, application guidance, and sourcing information in one place, adding value beyond the raw manufacturer datasheet. Note that many parametric values below are pending verification against the official Samsung datasheet and are marked .
Bộ thay thế dễ dàng lắp đặt cho K9LUGY8J7D-BCK0 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với K9LUGY8J7D-BCK0 (cùng hình factor và footprint) — khác nhau ở Memory Type, Cell Type, Technology, RoHS Status, Density.
K9KUGY8J7C-BCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9KUGY8J7C-CCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9JUGY8J5C-BCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9JUGY8J5C-CCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9IUGY8J7B-BCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9IUGY8J7B-CCK0
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →K9LUGY8J7D-BCK0 Tỷ lệ tối đa & tính chất điện
| Manufacturer | Samsung Electronics |
| Product Type | 3D V-NAND Flash Memory |
| Memory Technology | V-NAND (3D NAND flash) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | unknown |
Hướng dẫn cấu hình chân K9LUGY8J7D-BCK0 standard
Cấu hình chân cho K9LUGY8J7D-BCK0 (standard gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho K9LUGY8J7D-BCK0.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
K9LUGY8J7D-BCK0 phù hợp cho 6 Áp dụngs: Solid-State Drives, Embedded eMMC / UFS Storage, Industrial Storage Modules, Set-Top Boxes and Smart TVs, Networking and Telecom Equipment, Automotive Infotainment and Telematics.
Solid-State Drives
Samsung V-NAND devices of the K9LUGY8J7D class are core storage media in client and consumer SSDs. The vertical 3D cell stacking delivers high bits per package, allowing SSD controllers to aggregate multiple dies on shared channels for parallelism. In this role the NAND connects to an SSD controller over toggle-mode/ONFI interfaces; the controller implements wear leveling, LDPC ECC, and garbage collection to manage TLC cell endurance characteristics. The design benefit is high capacity per BGA footprint with Samsung's mature V-NAND reliability record, while the trade-off is strict dependence on controller firmware quality for endurance and retention.
Được đề xuất
Embedded eMMC / UFS Storage
Raw V-NAND of this family is packaged by Samsung into eMMC and UFS embedded storage modules used in smartphones, tablets, and IoT devices. The K9LUGY8J7D-class NAND provides the non-volatile layer behind the eMMC/UFS controller, which abstracts NAND management from the host. Benefits include proven V-NAND endurance, high sequential throughput over the UFS interface, and industrial temperature options. Designers of custom embedded boards who choose raw NAND instead of finished eMMC gain cost control but must implement full flash translation layers, bad-block management, and refresh algorithms in their host controller firmware.
Được đề xuất
Industrial Storage Modules
Industrial PCs, data loggers, and factory automation systems use V-NAND like the K9LUGY8J7D-BCK0 in CFast, mSATA, and board-level storage modules. V-NAND's charge-trap cells tolerate program-disturb stress better than planar NAND, supporting the high write duty cycles of logging applications. Industrial builds benefit from fixed-BOM supply agreements on Samsung NAND and predictable endurance data for maintenance scheduling. The design consideration is that industrial controllers must implement power-fail protection circuits (bulk capacitors plus firmware checkpointing) because unexpected power loss during a program operation can corrupt the affected page.
Được đề xuất
Set-Top Boxes and Smart TVs
Broadcast and streaming set-top boxes use K9LUGY8J7D-class V-NAND for firmware storage and DVR content buffering. The BGA NAND provides gigabit-class capacity in a compact footprint, and toggle-mode interfaces keep controller pin counts low. Low standby power of V-NAND suits always-on consumer electronics, and the TLC density point keeps bill-of-material cost competitive for high-volume CE manufacturing. Designers should verify the NAND's timing modes against the SoC's NAND controller, as many CE SoCs support only a subset of toggle-mode speeds, requiring conservative timing configuration at boot.
Được đề xuất
Networking and Telecom Equipment
Routers, switches, and 5G small-cell equipment store firmware, configuration, and log data on V-NAND devices of this class. The K9LUGY8J7D-BCK0's high density enables redundant firmware banks and extended log retention on a single package. Samsung V-NAND's stable read-disturb behavior suits equipment with 24/7 read-mostly duty cycles, and the BGA package withstands vibration better than card-based storage. Telecom designers typically pair the NAND with industrial-temperature controllers and must derate endurance estimates for continuous ambient temperatures above the consumer baseline specified in the Samsung datasheet.
Được đề xuất
Automotive Infotainment and Telematics
Automotive head units, digital clusters, and telematics control units require multi-gigabyte non-volatile storage for navigation maps and media, using V-NAND like the K9LUGY8J7D-BCK0 within automotive-qualified eMMC/UFS or raw-NAND subsystems. V-NAND tolerance of wide temperature swings and high vibration environments makes it well matched to vehicle electronics, and its density supports OTA update partitioning with A/B fallback banks. Automotive designers must verify the specific ordering code's qualification level (AEC-Q100 grade or Samsung automotive qualification), since suffix variants differ, and should implement power-interruption-safe FTL firmware for cranking and load-dump scenarios.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho K9LUGY8J7D-BCK0 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | K9KUGY8J7C-BCK0 | K9JUGY8J5C-BCK0 | K9IUGY8J7B-BCK0 |
|---|---|---|---|---|
| Brand | Samsung Electronics | Samsung Electronics | Samsung Electronics | Samsung Electronics |
| Generation / Revision | D revision (newest in family) | C revision (prior) | C revision, J5 family | B revision, I generation |
Bảo phân biệt quan trọng
- Newest D-revision V-NAND process generation (vsK9KUGY8J7C-BCK0)
- Longer supply longevity than older generations (vsK9IUGY8J7B-BCK0)
- Higher capacity option within the same family (vsK9JUGY8J5C-BCK0)
Ghi chú thiết kế
Samsung V-NAND devices use separate VCC (core) and VCCQ (I/O) supply rails. Decouple each rail with low-ESR ceramic capacitors (typically 0.1uF per ball group plus bulk capacitance) placed as close to the BGA as possible. Verify power sequencing between VCC and VCCQ in the device datasheet before power-tree design; incorrect sequencing can stress I/O structures. Estimated rail currents depend on operating mode (read, program, erase) and should be taken from the official Samsung datasheet ICC tables, which were not available in the current verified data.
In toggle-mode/DDR operation, DQ, RE#, and WE# lines toggle at high rates. Length-match the DQ bus within the tolerance specified by Samsung's layout guide, maintain a continuous ground reference plane beneath the bus, and avoid routing data lines across plane splits. Add series termination resistors near the driver as recommended for the applicable speed grade. Simulation of the full channel (controller, PCB trace, NAND input) is recommended for first-pass success on new boards using this V-NAND generation.
The most frequent raw-NAND design errors are under-provisioned ECC (modern TLC V-NAND needs LDPC, not simple BCH), missing bad-block management in the flash translation layer, and ignoring power-fail integrity - a lost power event during program/erase can corrupt the operating page or block. Budget firmware effort accordingly, and reserve spare blocks for wear leveling. Also confirm the exact -BCK0 suffix meaning (speed grade/packing) from Samsung before ordering, since suffix variants are not interchangeable on the same PCB in all cases.
Thông tin tuân thủ
No explicit compliance declarations for this exact ordering code were present in the retrieved web data. Samsung current-generation V-NAND is generally RoHS/lead-free compliant as standard; obtain the official declaration from Samsung Semiconductor product compliance documentation.
