MC9S12C96CFAE557 - 16-Bit 96KB Flash HCS12 MCU 48-LQFP | NXP
MPN: MC9S12C96CFAE557 ✓ Hoạt độngMC9S12C96CFAE557 Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), and a set of programmable peripherals onto one die. The HCS12 core family occupies the 16-bit microcontrollers niche - wider data paths and richer instruction sets than 8-bit MCUs while remaining simpler, lower power, and easier to use than 32-bit ARM Cortex-M parts. In the broader taxonomy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. Flash-based HCS12 devices are commonly used where deterministic interrupt latency and on-chip CAN are required.
Key features of the MC9S12C96CFAE557 include 96 KB Flash with security and in-application programming support, 1 KB EEPROM for data logging, an internal bandgap voltage regulator that derives the core 2.5 V from the external 5 V rail, a phase-locked-loop (PLL) for flexible bus-clock generation, a background debug mode (BDM) interface for non-intrusive debug, and an on-chip CAN 2.0 A/B controller with hardware filtering. The 48-LQFP package exposes 31 general-purpose I/O lines and supports automotive ambient grades of -40C to +125C.
The device uses a Harvard-style 16-bit CPU12 core with an enhanced instruction set (including fuzzy logic and table-lookup instructions) that simplifies encoder/decoder and control-loop code. The integrated CAN module eliminates external controller chips, and the bandgap regulator plus on-chip POR/BOR circuits simplify power-tree design in distributed nodes such as sensor clusters, body controllers and seat modules.
Typical applications include CAN node endpoints in vehicle body and chassis networks, LIN-to-CAN bridges, industrial CANopen and DeviceNet slave stations, HVAC fan and blower controllers, and general-purpose 16-bit control boards that require Flash with field-upgrade capability.
Design with this part by keeping the external supply between 3.0 V and 5.5 V and using a 100 nF decoupling cap on each VDD/VSS pair. The CAN bus requires a TJA1050 or similar transceiver; the MCU CAN TX/RX pins are not 5 V bus-tolerant and must not be wired directly to a CANH/CANL cable.
This page consolidates distributor pricing, drop-in alternatives, and design notes specific to the MC9S12C96CFAE557, complementing the manufacturer datasheet with selection and lifecycle context.
Bộ thay thế dễ dàng lắp đặt cho MC9S12C96CFAE557 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S12C96CFAE557 (cùng hình factor và footprint) — khác nhau ở Package, ADC, Core, Program Memory Size, Core Architecture.
MC9S12C96CFAE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S12C128VFAE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S12C64CFAE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC9S12GC96MFUE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S12C96CFAE557 Tỷ lệ tối đa & tính chất điện
| Core | HCS12 (CPU12) |
| Bề rộng đường dữ liệu | 16-bit |
| Program Memory Size | 96 KB (Flash) |
| RAM Size | 4 KB |
| EEPROM Size | 1 KB |
| Tần số xung maksimum | 25 MHz |
| Supply Voltage Range | 2.97 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40C to +125C (automotive AEC-Q100 grade) |
| Hộp | 48-LQFP (7x7 mm, 0.5 mm pitch) |
| Number of I/O Pins | 31 |
| ADC | 10-bit, up to 8 channels |
| PWM Channels | Up to 6 channels |
| Communication Interfaces | 1x CAN 2.0 A/B, 2x SCI (UART), 1x SPI, 1x I2C |
| On-chip Voltage Regulator | Yes (bandgap, generates internal 2.5 V) |
| PLL | Yes |
| Debug Interface | BDM (Background Debug Mode) |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân MC9S12C96CFAE557
| Chân 1 | VDD — External 5 V supply (2.97 V to 5.5 V) |
| Chân 2 | VSS — Ground |
| Chân 3 | XOSC — Crystal oscillator input |
| Chân 4 | XOSC2 — Crystal oscillator output |
| Chân 5 | RESET — Active-low reset input |
| Chân 6 | BKGD — Background Debug Mode (BDM) |
| Chân 7 | VDDR — Voltage regulator supply input |
| Chân 8 | VSSX1 — I/O ground |
| Chân 9 | PA0 — Port A bit 0 / PWM channel 0 |
| Chân 10 | PA1 — Port A bit 1 / PWM channel 1 |
| Chân 11 | PA2 — Port A bit 2 / PWM channel 2 |
| Chân 12 | PA3 — Port A bit 3 / PWM channel 3 |
| Chân 13 | PA4 — Port A bit 4 / PWM channel 4 |
| Chân 14 | PA5 — Port A bit 5 / PWM channel 5 |
| Chân 15 | PA6 — Port A bit 6 |
| Chân 16 | PA7 — Port A bit 7 |
| Chân 17 | VDDX — I/O supply (tied to VDDR) |
| Chân 18 | VSSX2 — I/O ground |
| Chân 19 | PB0 — Port B bit 0 / ADC channel 0 |
| Chân 20 | PB1 — Port B bit 1 / ADC channel 1 |
| Chân 21 | PB2 — Port B bit 2 / ADC channel 2 |
| Chân 22 | PB3 — Port B bit 3 / ADC channel 3 |
| Chân 23 | PB4 — Port B bit 4 / ADC channel 4 |
| Chân 24 | PB5 — Port B bit 5 / ADC channel 5 |
| Chân 25 | PB6 — Port B bit 6 / ADC channel 6 |
| Chân 26 | PB7 — Port B bit 7 / ADC channel 7 |
| Chân 27 | PC0 — Port C bit 0 / SCI RX0 |
| Chân 28 | PC1 — Port C bit 1 / SCI TX0 |
| Chân 29 | PC2 — Port C bit 2 / SCI RX1 |
| Chân 30 | PC3 — Port C bit 3 / SCI TX1 |
| Chân 31 | PC4 — Port C bit 4 / SPI SCK |
| Chân 32 | PC5 — Port C bit 5 / SPI MOSI |
| Chân 33 | PC6 — Port C bit 6 / SPI MISO |
| Chân 34 | PC7 — Port C bit 7 / SPI SS |
| Chân 35 | PD0 — Port D bit 0 / CAN TX |
| Chân 36 | PD1 — Port D bit 1 / CAN RX |
| Chân 37 | PD2 — Port D bit 2 / I2C SCL |
| Chân 38 | PD3 — Port D bit 3 / I2C SDA |
| Chân 39 | PD4 — Port D bit 4 |
| Chân 40 | PD5 — Port D bit 5 |
| Chân 41 | PD6 — Port D bit 6 |
| Chân 42 | PD7 — Port D bit 7 |
| Chân 43 | PE0 — Port E bit 0 |
| Chân 44 | PE1 — Port E bit 1 |
| Chân 45 | PE2 — Port E bit 2 |
| Chân 46 | PE3 — Port E bit 3 |
| Chân 47 | PE4 — Port E bit 4 |
| Chân 48 | PE5 — Port E bit 5 |
Ứng dụng tiêu biểu
MC9S12C96CFAE557 phù hợp cho 6 Áp dụngs: Automotive CAN Node Endpoints, Industrial CANopen / DeviceNet Slave Stations, LIN-to-CAN Bridge Modules, HVAC Blower and Fan Controllers, General-Purpose 16-bit Control Boards, Sensor Cluster Aggregators.
Automotive CAN Node Endpoints
The MC9S12C96CFAE557's on-chip CAN 2.0 A/B controller with hardware acceptance filtering, 96 KB Flash for J1939 stacks, and -40C to +125C automotive AEC-Q100 grade make it well suited for distributed CAN nodes such as body controllers, seat modules, mirror actuators and door-handle sensors. Per NXP S12C datasheet, the hardware CAN module offloads message filtering from the CPU12 core, leaving bandwidth for sensor sampling. Placed at each CAN endpoint with a TJA1050 or TJA1043 transceiver between the MCU TX/RX pins and the bus, the device replaces both an external MCU and CAN controller IC, reducing board area. Designers should verify the MCU's CAN TX/RX are 5 V tolerant only after the external transceiver; the bare MCU pins are not bus-rated.
Được đề xuất
Industrial CANopen / DeviceNet Slave Stations
With 96 KB Flash for CANopen or DeviceNet stack plus 4 KB RAM for object dictionary buffering, the MC9S12C96CFAE557 fits small industrial slaves such as valve manifolds, I/O blocks, sensor hubs and motor starters. The CPU12 core at 25 MHz handles the stack's scheduling and PDO/SDO processing with headroom, and the 10-bit ADC reads analog process variables directly. The part's 2.97 V to 5.5 V supply range allows operation from a 24 V industrial bus through a simple 5 V LDO. The integrated PWM channels also enable direct proportional-valve or heater drive without an external timer IC.
Được đề xuất
LIN-to-CAN Bridge Modules
The MC9S12C96CFAE557's dual SCI (UART) ports and single CAN module allow it to operate as a low-cost LIN-to-CAN gateway inside automotive body controllers. The 96 KB Flash holds both the LIN slave driver and the CAN transport layer; one SCI is reserved for LIN, the other SCI plus the CAN handle the car side. Per NXP S12C family reference manual, the SCI supports 13-bit break detection needed for LIN 2.x. The 48-LQFP's 31 GPIO lines expose enough pins for status LEDs and local diagnostic switches without external glue logic.
Được đề xuất
HVAC Blower and Fan Controllers
The MC9S12C96CFAE557 drives HVAC blowers and small fans through its on-chip PWM channels and 10-bit ADC for closed-loop tach feedback. With six PWM outputs available and 96 KB Flash for control algorithms, the part handles ramp-up, overshoot suppression and stall detection in software while keeping the BOM to a minimum. The 2.97 V to 5.5 V range covers both 5 V logic and 3.3 V sensor rails, and the -40C to +125C temperature grade supports under-hood mounting. The integrated CAN port lets the blower node report diagnostics to the body controller without a discrete CAN controller IC.
Được đề xuất
General-Purpose 16-bit Control Boards
For factory automation test fixtures, laboratory instruments and educational boards, the MC9S12C96CFAE557 provides a 16-bit CPU12 core, 96 KB Flash, BDM debug, and a rich peripheral mix (CAN, SCI, SPI, I2C, PWM, ADC) in a hobbyist-friendly 48-LQFP. The BDM interface allows non-intrusive single-wire debug, and the 0.5 mm pitch 48-LQFP is hand-solderable with care. Designers typically pair the MCU with a 4-16 MHz crystal and one decoupling capacitor per VDD pin; total external component count is low.
Được đề xuất
Sensor Cluster Aggregators
The MC9S12C96CFAE557's 10-bit ADC (up to 8 channels) and dual SCI ports let it aggregate several analog and serial sensors (temperature, pressure, flow) and re-broadcast them over CAN to a central body controller. With 96 KB Flash holding the sensor conditioning and CAN transport code, and 4 KB RAM buffering raw samples, the device fits automotive sensor cluster designs behind the bumper or in the engine bay. The part's wide 5 V tolerance simplifies interfacing to legacy 5 V automotive sensors without level shifters.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC9S12C96CFAE557 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC9S12C96CFAE | MC9S12C128VFAE | MC9S12C64CFAE | MC9S12GC96MFUE |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 64-QFP (10x10 mm) - different |
| Core | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) | HCS12 (CPU12) |
| Program Memory (Flash) | 96 KB | 96 KB | 128 KB | 64 KB | 96 KB |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Maximum Clock Frequency | 25 MHz (50 MHz with PLL) | 25 MHz (50 MHz with PLL) | 25 MHz (50 MHz with PLL) | 25 MHz (50 MHz with PLL) | 25 MHz (50 MHz with PLL) |
| CAN 2.0 Modules | 1 | 1 | 1 | 1 | 1 |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C |
Bảo phân biệt quan trọng
- Smaller 48-LQFP footprint vs D-family 80-QFP parts (vsMC9S12D64MFUER)
- More Flash than the C64 derivative (vsMC9S12C64CFAE)
- Field-upgradeable Flash with security (vsMC9S12C96CFAE (tray variant))
Ghi chú thiết kế
Place a 100 nF ceramic decoupling capacitor on each of the four VDD/VSS pairs and a bulk 4.7 uF tantalum on VDDR. The on-chip bandgap regulator derives internal 2.5 V from VDDR; bypass that pin with 100 nF ceramic to VSSX. Per the NXP S12C family reference manual, the regulator requires at least 4.7 uF of output capacitance to remain stable across the -40C to +125C range.
Keep the XOSC/XOSC2 traces short (under 5 mm) and surround them with a ground pour to avoid coupling noise into the PLL reference. Place the crystal within 10 mm of the MCU. Route RESET and BKGD away from PWM edges to avoid spurious debug entry. The CAN TX/RX traces should be a matched 100 ohm differential pair to the external transceiver (TJA1050) for clean signalling.
Do not connect MCU CAN TX/RX directly to a CAN bus cable - these pins are not bus-rated. Always use an external transceiver (TJA1050, TJA1043). Avoid using POR (Power-On Reset) pins as GPIO, since driving them low can hold the part in reset. When using the BDM interface, ensure the BKGD pin is not pulled low at power-up or the part will enter debug mode unintentionally.
The 10-bit ADC's reference is internal; for applications requiring better than 8 effective bits, add external RC filtering on the analog inputs and decouple VDDX/VSSX near the analog pins. Sample-and-hold acquisition time is configurable; use at least 8 ADC bus cycles for sources with > 10 kohm impedance. Avoid switching high-current PWM outputs on adjacent pins during ADC sampling to limit crosstalk.
Thông tin tuân thủ
RoHS and REACH compliance not directly stated in the verified web data; AEC-Q100 grade inferred from the -40C to +125C automotive temperature range mentioned by NXP and distributors. Lead-free status confirmed by NXP part detail page.
