LM2904BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
MPN: LM2904BAIDR ✓ 啟用中LM2904BAIDR 概覽
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy, an operational amplifier belongs to the amplifier IC family and ultimately serves as a building block in analog, mixed-signal, and control systems. Unlike a discrete transistor stage, a dual operational amplifier integrates gain stages, biasing, compensation, output drivers, and protection functions into one package.
The LM2904BAIDR provides two independent amplifier channels, a 1.2 MHz gain bandwidth product, and offset voltage specified to 2 mV. Its 36 V maximum supply rating provides additional operating headroom for industrial systems and laboratory equipment. The operating temperature range extends from -40°C to 125°C, supporting applications across commercial and industrial temperature environments. The 8-pin SOIC footprint also supports conventional surface-mount assembly and hand-soldering workflows.
Texas Instruments positions the LM2904B family as an upgraded functional relative to the original LM2904 family. The LM2904B page identifies a 36 V maximum supply voltage and 1.2 MHz gain bandwidth product, while the original LM2904 page identifies a 26 V maximum supply voltage and 700 kHz gain bandwidth product. This generational increase provides more bandwidth and supply-voltage headroom without changing the familiar dual-amplifier architecture.
Typical uses include low-frequency instrumentation, industrial sensor interfaces, audio preamplification, communications equipment, active filtering, comparators, and general DC signal amplification. Two channels can implement differential, summing, feedback, or multi-stage amplifier arrangements. The 1.2 MHz bandwidth makes the device most appropriate for signals well below the upper practical frequency range of this general-purpose amplifier family.
Designers should verify the input common-mode range, output swing, input bias current, noise, and load capability against their actual operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. The two amplifier outputs should not be tied together unless the application explicitly supports a particular parallel-output configuration.
This page combines the LM2904BAIDR ordering information, principal electrical ratings, lifecycle context, and family-level replacement guidance. It also identifies same-package alternatives and explains when the original LM2904, the enhanced LM2904B, or the specifically ordered BA suffix best matches a design requirement.
直接替換替代品,適用於 LM2904BAIDR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904BAIDR (相同外形與佔位) — 差異在於 Amplifier Type, Input Offset Voltage, Number of Channels, Package, Operating Temperature Range.
LM2904BIDR
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2904AIDR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM2904ADR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM2904BAIDR 最大額定值與電氣特性
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Maximum Supply Voltage | 36 V |
| Gain Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV maximum |
| 工作溫度範圍 | -40°C to +125°C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Channel Count | 2 channels |
| Original LM2904 Maximum Supply Voltage | 26 V |
| Original LM2904 Gain Bandwidth Product | 700 kHz |
LM2904BAIDR 腳位配置
| 腳位 1 | OUT1 — Output of amplifier channel 1 |
| 腳位 2 | IN1- — Inverting input of amplifier channel 1 |
| 腳位 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| 腳位 6 | IN2- — Inverting input of amplifier channel 2 |
| 腳位 7 | OUT2 — Output of amplifier channel 2 |
| 腳位 8 | V+ — Positive supply connection |
典型應用
LM2904BAIDR 適用於 6 應用s: Industrial Sensor Signal Conditioning, Audio Preamplification, Communications Interface Amplification, Active Filters and Control Loops, Power Supply Monitoring and Feedback, Portable Battery-Powered Measurement.
Industrial Sensor Signal Conditioning
The LM2904BAIDR is well suited to conditioning low-frequency industrial sensor signals because its dual 1.2 MHz channels provide useful bandwidth for common pressure, temperature, and position transducer stages. The 36 V maximum supply rating provides additional headroom for 24 V industrial systems, while the -40°C to 125°C operating range supports equipment deployed across varied ambient conditions. Two channels can form a non-inverting stage followed by an active low-pass filter, or they can implement differential excitation and readout where source impedances remain compatible with the amplifier's input-bias and common-mode limits. A regulated bypass capacitor near the supply pins and short, shielded analog traces help reduce susceptibility to industrial noise. Verify the input common-mode range, output swing, sensor grounding method, and required precision before finalizing the signal chain.
推薦
Audio Preamplification
The LM2904BAIDR can implement low-frequency audio preamplification with two independent channels in a compact 8-pin SOIC package. Its 1.2 MHz gain bandwidth product is substantially above the audio band, leaving practical headroom for gain stages and moderate low-pass filtering around the signal path. The dual arrangement supports balanced input stages, stereo preamplifiers, microphone boosters, and active tone controls. Actual audio quality depends on voltage noise, input bias current, common-mode range, and output swing, so source impedance and loading must be checked against the manufacturer limits. For a quiet source, add a suitable bypass capacitor at each supply pin and keep the return path close to the analog ground reference. The 36 V rating also permits operation from higher legacy supply rails when the circuit does not otherwise exceed the amplifier's operating limits.
推薦
Communications Interface Amplification
The LM2904BAIDR is applicable in communications equipment that requires two low-frequency amplification or filtering channels within a 36 V supply environment. The 1.2 MHz gain bandwidth can support receiver-interface gain, threshold shaping, and modest band-limiting stages without approaching the amplifier's upper bandwidth limit. Its dual channel count reduces the number of packages required for a balanced receiver or a two-stage interface. Designers should account for the exact input common-mode range, output swing, and load impedance because a valid package pinout alone does not guarantee signal compatibility. Keep the input and feedback traces short, use a low-noise local supply bypass capacitor, and maintain a single-point ground reference where possible. For line-card equipment operating from a 12 V or 24 V rail, confirm ripple, startup behavior, and output drive at the highest expected signal and load conditions.
推薦
Active Filters and Control Loops
The LM2904BAIDR is suitable for active filters and low-frequency control loops where two amplifiers are needed to form second-order or multi-stage networks. A 1.2 MHz gain bandwidth product allows useful loop gain above the intended filter or control bandwidth, while each channel can provide inversion, non-inversion, integration, or active-feedback functions. Component tolerances and amplifier open-loop behavior will influence the achieved response, so validate stability and gain margin in simulation with realistic loading. Place feedback resistors and capacitors close to their corresponding pins, avoid long high-impedance nodes, and provide local supply decoupling to reduce phase perturbations from supply impedance. The 8-pin SOIC package offers a conventional surface-mount assembly format and can reduce board area compared with two single-amplifier packages. Confirm output-current capability when the filter drives a downstream ADC, sensor, or relay-driver input.
推薦
Power Supply Monitoring and Feedback
The LM2904BAIDR can compare a divided feedback voltage against a reference and provide an amplified error signal for slow power-supply monitoring or laboratory regulation loops. The 36 V maximum supply voltage gives the amplifier ample nominal operating range on many 12 V or 24 V industrial rails, while the two channels can monitor positive and negative outputs or implement a differential sensing arrangement. Stable operation requires checking the input common-mode limits around the reference node, the output swing near the error-signal limits, and the load presented by the feedback controller. A local bypass capacitor helps maintain supply impedance over the control bandwidth. Keep the high-impedance divider and reference nodes away from switching power stages, and evaluate loop compensation under minimum and maximum load conditions. The amplifier's 1.2 MHz bandwidth is generally more than adequate for slow supervisory loops but does not remove the need for deliberate compensation.
推薦
Portable Battery-Powered Measurement
The LM2904BAIDR can serve in portable battery-powered measurement equipment when its two amplifier channels and low-voltage operation are adequate for the selected supply. Its 1.2 MHz gain bandwidth supports gain and filtering stages for many low-frequency sensors without requiring two separate packages. The 36 V maximum supply rating does not require a 36 V rail; it defines the upper limit, allowing operation from lower battery-derived voltages when the minimum supply and input/output ranges remain valid. Low-power design decisions should include the amplifier quiescent current, which is not established by the product-page summary, as well as the load current and regulator efficiency. Place bypass capacitance at the supply pins, keep input nodes at high impedance, and use a low-leakage protection network when the source can be disconnected. Confirm battery-range operation across temperature and verify offset stability for the required measurement accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904BAIDR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904BIDR | LM2904AIDR | LM2904ADR | LM2904DR | LM2904D |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Gain Bandwidth Product | 1.2 MHz | 1.2 MHz | 700 kHz for original LM2904 family | 700 kHz for original LM2904 family | 700 kHz for original LM2904 family | 700 kHz for original LM2904 family |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Product Family | LM2904B | LM2904B | LM2904 | LM2904 | LM2904 | LM2904 |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
| Special Ordering Feature | BA ordering code | Standard B ordering code | A ordering code | A ordering code | Standard ordering code | Base ordering code |
主要差異化特點
- Higher bandwidth than the original LM2904 family (對比LM2904DR)
- Greater supply-voltage headroom (對比LM2904ADR)
- Two channels in one standard SOIC footprint (對比LM324WDT)
- Direct family continuity without changing the PCB footprint (對比LM2904BIDR)
設計說明
Place the supply bypass capacitor as close as practical to pins 4 and 8, with a short, low-impedance return path. For dual-amplifier layouts, route each channel's inverting-input feedback network close to its assigned amplifier and avoid routing between channels whenever possible. High-impedance non-inverting inputs are particularly susceptible to leakage and coupling, so minimize exposed trace length and keep them away from switching nodes, inductors, and power-supply traces.
The 36 V rating is a maximum operating limit, not a required supply voltage. Check the minimum operating voltage, input common-mode range, quiescent current, and output swing against the actual rail. A dual amplifier operating from a 24 V system still requires adequate headroom for its input signals and output swing. Use local regulation where necessary rather than allowing supply excursions to approach the 36 V maximum.
Do not assume that identical package outlines guarantee identical behavior. Compare offset voltage, input bias current, noise, common-mode range, output swing, slew rate, temperature grade, and qualification for every replacement candidate. The original LM2904 family is listed at 26 V and 700 kHz, while LM2904B is listed at 36 V and 1.2 MHz; substituting an original-family device into a design that relies on the enhanced limits may compromise margin.
Estimate dissipation from the actual output load and the voltage dropped across the output stage rather than from the full supply voltage alone. Verify that the load does not exceed the amplifier's output-current capability and provide adequate SOIC copper area for ambient-temperature operation. If both channels drive sustained heavy loads, evaluate each channel independently because shared package heating can raise the junction temperature of the complete device.
合規資訊
The LM2904B is a general-purpose operational amplifier, so AEC-Q100 is not applicable as an automotive qualification category. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the cited product-page summaries.