MPC860SRVR50D4R2 - PowerQUICC MPC8xx 50MHz MPU, 357-BGA | NXP
MPN： MPC860SRVR50D4R2 ⚠ 最後購買機會MPC860SRVR50D4R2 概覽
A microprocessor (MPU) is an integrated circuit that contains the arithmetic logic unit, control unit, and registers required to execute software instructions. In the embedded hierarchy, the MPC8xx family sits between general-purpose microcontrollers and high-end application processors, optimized for deterministic real-time control with integrated peripheral bridges. Power Architecture (formerly PowerPC) is the underlying instruction set, providing a 32-bit RISC execution pipeline well suited to protocol processing. PowerQUICC is NXP's brand name for MPC8xx-family parts that combine a PowerPC core with a separate RISC-based Communications Processor Module for offloading serial protocol handling.
Key features of the MPC860SRVR50D4R2 include an integrated CPM supporting HDLC, Ethernet, UART, and other serial protocols, dual 10/100 Mbps Ethernet interfaces via the Fast Ethernet Controller, and on-chip peripheral subsystems such as timers, interrupt controllers, and memory control for DRAM and SRAM. The part provides 4-channel DMA, I2C, SPI, and parallel I/O, alongside a PCMCIA/PC Card controller. These features reduce external component count and BOM cost in routing, switching, and telecom equipment designs.
Typical applications include WAN routers and remote access concentrators, ISDN terminal adapters, ATM switches, T1/E1 framers, industrial control with serial networking, and set-top box controllers. The CPM offloads HDLC framing and serial bit processing from the CPU, freeing the core for higher-layer protocol stacks.
When designing with this part, note the 357-ball BGA requires X-ray inspection and controlled reflow profiles. Use the recommended boot configuration word settings from the reference manual. Ensure proper decoupling on all power pins per the hardware specifications section of the MPC860 family datasheet, and verify DDR/SDRAM interface timing with the supplied IBIS models before PCB fabrication.
直接替換替代品，適用於 MPC860SRVR50D4R2 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MPC860SRVR50D4R2 （相同外形與佔位） — 差異在於 Processor Type, RoHS Status, Package, Mounting Type, Packaging.
MPC860ENCVR50D4
✅ 直接替換聯絡詢價
查看資料表 →MPC860TCVR50D4
✅ 直接替換聯絡詢價
查看資料表 →MPC860PZQ50D4
✅ 直接替換📋 參考替代品（不在目錄中）
MPC860DEZQ50D4
✅ 直接替換聯絡詢價
查看資料表 →MPC860SRVR50D4R2 最大額定值與電氣特性
| Processor Type | MPC8xx PowerQUICC, 32-Bit Power Architecture |
| Core Count | 1 |
| 最大時脈頻率 | 50 MHz |
| Operating Voltage | 3.3 V |
| 工作溫度範圍 | 0 C to +95 C |
| 封裝 | 357-BGA (25 x 25 mm) |
| 安裝類型 | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Lead Free Status | Lead Free |
| Process Technology | 0.32 um CMOS |
| Communications Processor Module | Yes (RISC CPM with HDLC, Ethernet, UART) |
| Ethernet Interfaces | 10/100 Mbps Fast Ethernet (FCC) |
| DMA Channels | 4 |
| Series | MPC860 |
| RoHS 狀態 | Compliant |
MPC860SRVR50D4R2 357-bga (25 x 25 mm) 腳位配置指南
MPC860SRVR50D4R2（357-bga (25 x 25 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MPC860SRVR50D4R2.
請參閱 資料表 以查看完整腳位配置。
典型應用
MPC860SRVR50D4R2 適用於 6 應用s: WAN Router and Remote Access Concentrator, ISDN Terminal Adapter, ATM Switch and Edge Controller, T1/E1 Framer Module, Industrial Serial Networking Controller, Set-Top Box and Embedded Media Controller.
WAN Router and Remote Access Concentrator
The MPC860SRVR50D4R2 is well suited to WAN router and remote access concentrator designs because its PowerQUICC architecture pairs a 50 MHz PowerPC core with a separate RISC-based Communications Processor Module that offloads HDLC framing and serial bit processing. The CPM's configurable serial channels and dual 10/100 Mbps Fast Ethernet controllers allow a single chip to terminate multiple T1/E1 lines and aggregate traffic onto a routed Ethernet backbone. Placing the CPM in the same silicon as the core removes the latency of an external framer, simplifying PCB layout. For new designs, the PowerQUICC II MPC8260 delivers higher CPM throughput; the original MPC860 remains the reference choice where verified stock and existing firmware are required.
推薦
ISDN Terminal Adapter
ISDN terminal adapters and BRI/PRI converter designs rely on the MPC860SRVR50D4R2's CPM to handle HDLC-based ISDN D-channel signaling while the PowerPC core runs higher-layer protocols. The integrated dual Fast Ethernet controllers enable a single device to bridge between an ISDN S/T interface and 10/100 Mbps Ethernet, reducing component count compared with a discrete framer plus microcontroller solution. At 50 MHz the part provides sufficient headroom for typical PPP/MLPPP stacks without thermal concerns in a small plastic BGA footprint. Engineers should note the part is in last-time-buy status, so legacy designs using this IC should plan for migration to the PowerQUICC II MPC8255 family.
推薦
ATM Switch and Edge Controller
ATM switch and edge controller designs use the MPC860SRVR50D4R2's CPM to terminate AAL5 segmentation and reassembly while the PowerPC core runs IP/ATM signalling and routing tables. The on-chip dual 10/100 Mbps Ethernet and configurable serial channels let a single MPC860 drive multiple ATM SAR ports in a compact edge concentrator. The 357-BGA package supports the multi-rail decoupling needed for clean AAL5 timing. Compared with newer MPC8255/MPC8260 devices the 50 MHz core can become a bottleneck at gigabit rates, so this part is best matched to T1/E1 or sub-100 Mbps ATM edge nodes.
推薦
T1/E1 Framer Module
T1/E1 framer and channel-bank modules integrate the MPC860SRVR50D4R2 to consolidate HDLC framing, bit error rate monitoring, and alarm detection in a single chip. The CPM's dedicated serial controllers execute HDLC bit-stuffing at line rate without CPU intervention, freeing the PowerPC core for higher-level OAM and SNMP handling. The 3.3V single-rail operation simplifies the power tree, while the 357-BGA keeps the design compact enough for a small daughter card that plugs into a central office shelf. Verified long-term availability is limited because the part is in last-time-buy, so design teams should verify remaining distributor stock before committing to new T1/E1 designs.
推薦
Industrial Serial Networking Controller
Industrial serial networking controllers use the MPC860SRVR50D4R2 to bridge RS-232/422/485 and HDLC fieldbus traffic onto Ethernet networks in factory automation cells. The on-chip I2C and SPI controllers let the same chip talk to EEPROM, real-time clocks, and ADC front ends, eliminating the need for a separate microcontroller. The 0 to 95 C operating range covers most factory-floor enclosures, and the integrated DMA engine moves fieldbus packets between the CPM and memory without CPU overhead. Newer industrial designs should evaluate the PowerQUICC II/III families for longer production lifetimes; the original MPC860 fits existing field installations where verified compatibility matters.
推薦
Set-Top Box and Embedded Media Controller
Set-top box and embedded media controller designs use the MPC860SRVR50D4R2 to host an RTOS, run a graphical UI, and process transport-stream and Ethernet traffic simultaneously. The dual Fast Ethernet controllers let the box share a MoCA or HomePlug bridge on one port and an IP return path on the other. The 50 MHz PowerPC core is adequate for legacy MPEG-2 transport-stream parsing and CAS descrambling, while the CPM offloads serial control-plane traffic from the tuner interface. Memory control supports both SDRAM and SRAM, allowing flexible PSRAM expansion. Designers should plan migration to MPC8255/MPC8260 for new set-top platforms to extend production lifecycle.
推薦
推薦產品摘要
工程參考資料，適用於 MPC860SRVR50D4R2 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MPC860ENCVR50D4 | MPC860TCVR50D4 | MPC860PZQ50D4 | MPC860DEZQ50D4 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 357-BGA (25 x 25 mm) | 357-BGA - same | 357-BGA - same | 357-BGA - same | 357-BGA - same |
| Maximum Clock Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Architecture | PowerQUICC (PowerPC + RISC CPM) | PowerQUICC | PowerQUICC | PowerQUICC | PowerQUICC |
| Operating Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | 0 to +95 C | 0 to +95 C | 0 to +95 C | 0 to +95 C | 0 to +95 C |
| Ethernet Controllers | Dual 10/100 Mbps Fast Ethernet | Dual 10/100 Mbps | Dual 10/100 Mbps | Dual 10/100 Mbps | Dual 10/100 Mbps |
| Lifecycle Status | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy |
主要差異化特點
- Lead-free RoHS-compliant variant (對比MPC860SRVR50D4 (non-RoHS predecessor))
- 50 MHz operation within the PowerQUICC family (對比MPC860PVR80D4 (80 MHz))
- 357-BGA package for high-density designs (對比MPC860DTCZQ50D4 (different BGA pinout))
設計說明
Estimated: The MPC860SRVR50D4R2 in a 357-BGA (25 x 25 mm) package has a junction-to-ambient thermal resistance on the order of 20 to 25 C/W when soldered to a properly designed PCB with multiple thermal vias under the die. At 50 MHz and 3.3V the typical power dissipation is below 1 W, so most designs do not require an external heatsink. Provide at least 4 thermal vias under the central BGA pad and follow the NXP reference layout for supply decoupling.
The 357-ball BGA package requires controlled-impedance PCB traces for the SDRAM and Ethernet interfaces to meet the timing budgets in the MPC860 hardware specifications document. Use a 4-layer stack-up with continuous ground and power planes under the BGA, and place decoupling capacitors as close as possible to each power pin. Ball-grid arrays must be inspected with X-ray equipment post-reflow because solder joints are hidden beneath the package.
The MPC860SRVR50D4R2 is in last-time-buy status, so do not start new design wins on this exact MPN. Configure the boot word correctly during reset so the CPU can locate the reset vector and memory controller registers. Always sequence the 3.3V I/O supply before the core voltage according to the datasheet, otherwise the part can latch up. Validate IBIS models against the chosen SDRAM DIMM vendor before board fabrication to avoid timing violations.
合規資訊
RoHS compliant and lead free per R2 suffix. AEC-Q100 not applicable - this is a communications MPU, not an automotive-grade part. Conflict-mineral reporting compliant per NXP policy.
