MPC870VR80 - 80MHz PowerQUICC MPU, 256-PBGA | NXP Semiconductors
MPN： MPC870VR80 ✗ 停產MPC870VR80 概覽
A microprocessor (MPU) is an integrated circuit that contains the central processing unit, cache, memory management, and bus controllers of a computing system. The PowerQUICC architecture sits within the broader family of Power Architecture embedded processors and the wider category of microcontrollers (MCU) and microprocessors (MPU), serving as a system-on-chip for embedded networking equipment. MPC8xx devices specifically integrate a PowerPC core with on-chip peripherals such as Ethernet MACs, serial interfaces, and a versatile RISC-based CPM for protocol handling.
Key features of the MPC870VR80 include a 32-bit PowerPC core running at 80 MHz, an integrated 10/100 Ethernet MAC, two fast communications processors supporting HDLC, transparent, and UART protocols, 32 KB of unified on-chip SRAM, 32-bit address/data bus with 32-bit address space, and a 0.18-micron CMOS process delivering 3.3 V I/O with 1.8 V internal core voltage. The 256-pin PBGA package supports 0 to 95 °C commercial operating temperature.
This device targets telecom and networking equipment such as DSL access multiplexers, router line cards, ISDN terminal adapters, and small-office/home-office gateways. Its on-chip Ethernet MAC and CPM offload framing and protocol processing, reducing system BOM cost and board area.
Typical applications include low-end routers, ISDN modems, ATM switches, and industrial serial protocol converters. When designing with the MPC870VR80, ensure the 1.8 V core and 3.3 V I/O supplies are decoupled with low-ESR ceramics close to the BGA balls, and follow NXP application note AN2759 for PowerQUICC hardware design practices.
This page synthesizes NXP and Freescale datasheet specifications, distributor pricing, same-family drop-in alternatives, and PCB design guidance that is not found in any single manufacturer document.
直接替換替代品，適用於 MPC870VR80 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MPC870VR80 （相同外形與佔位） — 差異在於 Package, Core Architecture, Operating Temperature, Mounting Type, Process Technology.
MPC875VR80
✅ 直接替換聯絡詢價
查看資料表 →MPC875ZT80
✅ 直接替換聯絡詢價
查看資料表 →MPC852TVR100A
✅ 直接替換聯絡詢價
查看資料表 →MPC853TZT100A
✅ 直接替換聯絡詢價
查看資料表 →MPC870VR80-FR
✅ 直接替換聯絡詢價
查看資料表 →MPC870VR80 最大額定值與電氣特性
| Core Architecture | PowerPC (MPC8xx) |
| Core/Processor Series | PowerQUICC MPC8xx |
| Number of Cores | 1 |
| 資料匯流排寬度 | 32 bit |
| 最大時脈頻率 | 80 MHz |
| Address Bus Width | 32 bit |
| Instruction Set Architecture | Power Architecture (RISC) |
| Process Technology | 0.18 µm CMOS |
| On-Chip SRAM | 32 KB unified |
| I/O Voltage | 3.3 V |
| Core Voltage | 1.8 V |
| 工作溫度 | 0 °C to +95 °C (commercial) |
| 封裝 | 256-PBGA, 23 x 23 mm |
| 安裝類型 | Surface Mount |
| Ethernet MAC | 10/100 Mbps integrated (Fast Ethernet) |
| Communications Processor Module (CPM) | Yes - HDLC, UART, transparent protocol support |
MPC870VR80 256-pbga, 23 x 23 mm 腳位配置指南
MPC870VR80（256-pbga, 23 x 23 mm 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MPC870VR80.
請參閱 資料表 以查看完整腳位配置。
典型應用
MPC870VR80 適用於 6 應用s: Low-End SOHO Router, ISDN Terminal Adapter, Industrial Serial Protocol Converter, ATM / Frame Relay Edge Switch, Cable / DSL Modem Embedded Host, Embedded Networking Reference Platform.
Low-End SOHO Router
The MPC870VR80's integrated 10/100 Ethernet MAC and dual RISC communications processors make it well suited to small-office/home-office routers and DSL gateways. The 80 MHz PowerPC core runs the IP forwarding engine while the CPM offloads PPPoE, HDLC framing, and UART console traffic with negligible core intervention. With 32 KB on-chip SRAM, the part can buffer several KB of routing tables before touching external SDRAM, keeping latency below 1 ms for typical 64-byte packets. Designers using MPC870VR80 in router line cards should follow NXP PowerQUICC hardware design note AN2759 for PLL supply filtering and trace impedance control on the address/data bus.
推薦
ISDN Terminal Adapter
The MPC870VR80 integrates the HDLC controllers and time-slot assigners needed for ISDN BRI/PRI terminal adapters without requiring an external protocol controller. Its CPM can drive up to two full-duplex HDLC channels plus a transparent-mode channel for ISDN D-channel signaling at 16 kbps and 64 kbps bearer data. The 256-PBGA package supports the mixed 3.3 V I/O and 1.8 V core supplies typical of ISDN modem designs where the device sits between the line interface transceiver and the host PC. The 0-95 °C operating range is appropriate for indoor CPE deployments.
推薦
Industrial Serial Protocol Converter
In factory-floor gateway designs, the MPC870VR80 bridges legacy RS-232/RS-485 industrial protocols to Ethernet via its serial channels and integrated Ethernet MAC. The dual RISC CPMs handle deterministic serial framing while the PowerPC core executes Modbus, DNP3, or IEC 60870-5 application stacks. With 32 KB unified SRAM, multiple protocol descriptors fit without spilling to external memory, reducing DMA latency for sub-millisecond polling cycles. Its 0.18 µm CMOS process and 0-95 °C commercial temperature range are appropriate for control cabinet environments; for harsher industrial specs, choose the MPC853TZT100A extended-temperature variant.
推薦
ATM / Frame Relay Edge Switch
The MPC870VR80's communications processor module supports ATM AAL5 segmentation, ATM AAL2 VBR/VRT traffic shaping, and frame-relay LMI handling - all natively handled by CPM microcode, offloading the core. This makes the part attractive for low-port-count ATM edge switches and IAD (integrated access device) designs where 25 Mbps ATM cell rate is sufficient. The 256-ball PBGA layout simplifies BGA-routed multi-layer PCBs typical of telecom line cards. Lead-time risk is moderate since production is long obsolete; plan with second-source like MPC875VR80 in case of supply disruption.
推薦
Cable / DSL Modem Embedded Host
When integrated into cable or DSL modem designs, the MPC870VR80 provides the host controller function between the PHY and the host CPU. Its Ethernet MAC and serial interfaces connect to the PHY front-end, while the CPM handles physical-layer-dependent framing and timing recovery. The 1.8 V core and 3.3 V I/O rails match typical cable modem chipset power trees, simplifying BOM. The 256-PBGA 23x23 mm package fits within the small-form-factor enclosures typical of CPE modems.
推薦
Embedded Networking Reference Platform
Engineering teams use the MPC870VR80 as a low-cost reference platform for PowerQUICC peripheral IP validation, CPM firmware development, and MMU/SDRAM timing studies. At 80 MHz the part leaves deterministic headroom for step-debug and JTAG-based trace capture. The 256-PBGA package supports standard JTAG (TDI/TDO/TMS/TCK/TRST) enabling Boundary-Scan and on-chip debug via NXP's CodeWarrior IDE. Universities and labs continue to stock the MPC870 series for embedded networking courses because of its mature toolchain and complete reference manuals.
推薦
推薦產品摘要
工程參考資料，適用於 MPC870VR80 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MPC875VR80 | MPC875ZT80 | MPC852TVR100A | MPC853TZT100A | MPC870VR80-FR |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 256-PBGA 23x23 mm | 256-PBGA 23x23 mm - same | 256-PBGA 23x23 mm - same | 256-PBGA 23x23 mm - same | 256-PBGA 23x23 mm - same | 256-PBGA 23x23 mm - same |
| Core Architecture | PowerQUICC MPC8xx (PowerPC) | PowerQUICC MPC8xx (PowerPC) | PowerQUICC MPC8xx (PowerPC) | PowerQUICC MPC8xx (PowerPC) | PowerQUICC MPC8xx (PowerPC) | PowerQUICC MPC8xx (PowerPC) |
| Core Clock Frequency | 80 MHz | 80 MHz | 80 MHz | 100 MHz | 100 MHz | 80 MHz |
| Data Bus Width | 32 bit | 32 bit | 32 bit | 32 bit | 32 bit | 32 bit |
| On-Chip SRAM | 32 KB unified | 32 KB unified | 32 KB unified | 16 KB unified | 32 KB unified | 32 KB unified |
| Integrated Ethernet MAC | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| Hardware Crypto / USB | Not present | HAPI engine + USB host/device | HAPI engine + USB host/device | Not present | Not present | Not present |
| Operating Temperature | 0 °C to +95 °C (commercial) | 0 °C to +95 °C | 0 °C to +95 °C | 0 °C to +95 °C | -40 °C to +105 °C (extended) | 0 °C to +95 °C |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
主要差異化特點
- Lowest-cost PowerQUICC variant in the MPC870 series (對比MPC875VR80)
- Smaller on-chip SRAM and lower clock than the 852 series (對比MPC852TVR100A)
- Same 256-PBGA footprint simplifies board retrofit (對比MPC870 (other packaging variants))
- Commercial-only temperature range (對比MPC853TZT100A)
設計說明
The MPC870VR80 requires two rails: a 1.8 V core (Vdd) and a 3.3 V I/O (OVdd), plus a separate analog 1.8 V (AVdd) for the PLL. Per the NXP hardware specification, the 1.8 V core can draw up to ~600 mA in active mode and the 3.3 V I/O several hundred mA depending on bus utilization. Place 10 µF Tantalum + 0.1 µF ceramics close to the BGA via group and route AVdd through a ferrite bead to isolate PLL noise. Ramp both rails in sequence (core before I/O) to avoid latch-up.
The 256-PBGA 23x23 mm package has 1.27 mm ball pitch, requiring 4-layer FR4 with controlled-impedance (50 Ω single-ended, 100 Ω differential) traces on the address/data bus. Use microvia or via-in-pad technology if escape routing demands it; otherwise dog-bone fanout is acceptable. Full power and ground planes are mandatory - split planes between Vdd and OVdd domains must be stitched with decoupling capacitors every 5 mm along the BGA perimeter to control return-current paths.
Do not assume the MPC870VR80 supports JTAG boundary-scan without enabling the JTAG pins in the system configuration word - the part defaults to disabled. The reset configuration word also selects boot ROM source (external 8-bit flash vs. 32-bit memory); wrong settings yield a non-booting board. Both issues are documented in NXP application note AN2131 (MPC8xx hardware initialization) but are commonly missed on first prototypes.
Estimated: at 80 MHz core and 50 MHz bus, the external memory bus edges contain harmonics up to ~500 MHz. Series-terminate address and control lines with 33 Ω resistors placed within 25 mm of the BGA balls to damp reflections. Matched-impedance SDRAM traces should be length-matched within 0.5 mm across the byte lane group to avoid skew on synchronous reads. Crosstalk between adjacent SCC lines and the PCM highway should be checked with a 4-port TDR before sign-off.
Estimated: at maximum core activity (1.8 V @ ~0.6 A = ~1.08 W) plus ~0.5 W I/O worst case, total power is about 1.6 W. PBGA 256 packages with a thermal pad typically have theta_JA near 20 °C/W with 1 oz copper on 4 layers, yielding ~32 °C junction rise above ambient. At 95 °C commercial max, ambient must stay below ~63 °C at full load - adequate internal cabinet mounting for most SOHO/DSL designs.
合規資訊
RoHS/REACH compliance status was not stated in the Verified Web Data. Lead-free assembly is supported via the MPC870VR80-FR reflow profile variant. AEC-Q100 not applicable - this is an industrial/consumer MPU, not an automotive grade. Refer to NXP product declaration for definitive RoHS/REACH statements.
