IQEH50NE2LM7UCGSCATMA1 - 25V OptiMOS 7 N-Ch MOSFET | Infineon
料号： IQEH50NE2LM7UCGSCATMA1 ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.95 | $2.95 |
| 10 | $2.65 | $26.50 |
| 100 | $2.32 | $232.00 |
| 500 | $2.05 | $1,025.00 |
| 1,000 | $1.78 | $1,780.00 |
IQEH50NE2LM7UCGSCATMA1 概述
An N-channel power MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) is a voltage-controlled three-terminal device in which a positive gate-source voltage creates a conductive channel between drain and source. Power MOSFETs sit inside the broader semiconductor hierarchy: MOSFET -> discrete semiconductor -> power discrete -> switch-mode power conversion building block. Optimized low-voltage MOSFETs such as this part are routinely used as synchronous rectifiers on the secondary side of buck converters, where every milliohm of RDS(on) translates directly into conduction loss, efficiency, and thermal headroom.
Key differentiating parameters include 25 V drain-source breakdown voltage optimized for 12 V rails, 0.5 mΩ maximum on-resistance for minimum conduction loss, 175°C rated junction temperature for harsh thermal environments, and a 2 V typical gate threshold enabling low-voltage gate drive. The device dissipates 2.5 W at TA and 150 W at TC, with PCB layout on 6 cm² of copper drain area per the datasheet characterization conditions. The PG-WHTFN-9-1 package provides top-side cooling and a small footprint suitable for high-density VRM topologies.
Typical applications include AI accelerator point-of-load converters, server core voltage rails, telecom 48 V intermediate bus converters, hot-swap circuits, and OR-ing FETs in redundant power supplies. Its low RDS(on) and high current rating make it especially suitable as a synchronous rectifier where switching losses and conduction losses both matter.
When designing with this part, prioritize Kelvin-source gate drive to fully realize the 0.5 mΩ rating, and use the datasheet SOA diagram to verify operation under fault and transient conditions. PCB layout should minimize source-inductance loop area and maximize copper on the drain tab for thermal spreading.
This page synthesizes distributor inventory, parametric comparison with drop-in alternatives, and design notes not found in the manufacturer datasheet, helping engineers select and qualify the part faster.
直接替换替代料： IQEH50NE2LM7UCGSCATMA1 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： IQEH50NE2LM7UCGSCATMA1 （相同外形与封装尺寸） ——差异在于 Package, Technology, Operating Temperature Range, Drain-Source Voltage (VDS), Power Dissipation (Tc).
快速对比工具——选择替代料号进行并排对比：
IQEH50NE2LM7UCGSC
✅ 直接替换📋 参考替代料（不在目录中）
IQE220N15NM5CGSCATMA1
✅ 直接替换✓ 有现货
$2.18 / 个
查看数据手册 →BSC014NE2LSIATMA1
✅ 直接替换✓ 有现货
$0.48 / 个
查看数据手册 →ISC037N12NM6ATMA1
✅ 直接替换✓ 有现货
$3.62 / 个
查看数据手册 →ISC015N06NM5LF2ATMA1
✅ 直接替换✓ 有现货
$2.21 / 个
查看数据手册 →IQEH50NE2LM7UCGSCATMA1 最大额定值与电气特性
| Manufacturer | Infineon Technologies |
| Product Family | OptiMOS 7 Power-Transistor |
| 晶体管类型 | N-Channel MOSFET |
| Drain-Source Voltage (VDS) Max | 25 V |
| Continuous Drain Current (ID) at TA | 54 A |
| Continuous Drain Current (ID) at TC | 422 A |
| RDS(on) Max | 0.5 mΩ |
| Gate Threshold Voltage (VGS(th)) typ | 2 V |
| Power Dissipation (PD) at TA | 2.5 W |
| Power Dissipation (PD) at TC | 150 W |
| Maximum Junction Temperature | 175 °C |
| 封装 | PG-WHTFN-9-1 (surface mount) |
| 安装类型 | Surface Mount |
| Series | OptiMOS 7 |
| Technology | Silicon N-Channel Power MOSFET |
IQEH50NE2LM7UCGSCATMA1 pg-whtfn-9-1 (surface mount) 引脚配置指南
IQEH50NE2LM7UCGSCATMA1（pg-whtfn-9-1 (surface mount) 封装）的引脚配置。 该功率器件具有栅极、漏极和源极端子。对于无极性封装，请参阅制造商数据手册以了解确切的引脚 1 方向和封装尺寸细节。常见应用包括电源设计、电机驱动和负载开关。
暂无详细引脚数据： IQEH50NE2LM7UCGSCATMA1.
请参阅 数据手册 以查看完整引脚配置。
安全工作区
典型应用
IQEH50NE2LM7UCGSCATMA1 适用于 6 应用s: AI Server Point-of-Load Converters, Data Center 48 V Intermediate Bus Converters, Telecom Hot-Swap and OR-ing FETs, Synchronous Rectification in Server VRMs, Industrial High-Current DC-DC Modules, Battery Protection and Power Path Management.
AI Server Point-of-Load Converters
The IQEH50NE2LM7UCGSCATMA1 is well matched to 12 V point-of-load (PoL) converters feeding AI accelerator cores. Its 0.5 mΩ max RDS(on) and 422 A pulsed TC current let it serve as a synchronous rectifier with very low conduction loss, while the 25 V VDS rating provides comfortable headroom above the 12 V nominal bus. The PG-WHTFN-9-1 footprint supports dense VRM layouts typical of AI accelerator boards, where every milliohm of RDS(on) directly improves efficiency and reduces thermal load.
推荐
Data Center 48 V Intermediate Bus Converters
For 48 V intermediate bus architectures, the IQEH50NE2LM7UCGSCATMA1 can be used on the secondary-side synchronous rectification stage where high current and low loss are mandatory. The 25 V VDS allows placement on the 12 V output side of a multi-stage IBC. Its 175°C maximum junction temperature supports sustained high-current operation in well-cooled server chassis, and the 0.5 mΩ RDS(on) keeps conduction loss manageable even at hundreds of amps.
推荐
Telecom Hot-Swap and OR-ing FETs
The IQEH50NE2LM7UCGSCATMA1 serves as a hot-swap or OR-ing FET on -48 V telecom distribution boards where its low RDS(on) minimizes steady-state dissipation while the 25 V class fits 12 V load-side rails. The 54 A continuous TA rating supports typical 240-360 W load circuits. PG-WHTFN-9-1's top-side thermal pad aids board-level cooling, and the Infineon OptiMOS 7 process provides tight threshold distribution for predictable current sharing across redundant supplies.
推荐
Synchronous Rectification in Server VRMs
The IQEH50NE2LM7UCGSCATMA1 is engineered as a synchronous rectifier (low-side FET) in multi-phase buck VRMs for server CPUs and GPUs. With 0.5 mΩ max RDS(on) and 2 V typical gate threshold, it pairs with a companion high-side MOSFET and a 3.3 V-capable gate driver. Its 175°C rating and 150 W PD at TC enable sustained high current per phase, while the surface-mount PG-WHTFN-9-1 package reduces loop inductance compared to DPAK, helping minimize switching loss.
推荐
Industrial High-Current DC-DC Modules
In industrial 24 V to 12 V buck modules and high-current DC-DC bricks, the IQEH50NE2LM7UCGSCATMA1 fits as the synchronous rectifier or main switch on the 12 V side. Its 0.5 mΩ RDS(on) and 422 A pulsed rating support kilowatt-class brick converters. The wide -55°C to +175°C operating range suits industrial environments, and the small PG-WHTFN-9-1 footprint allows compact brick designs while the top-side thermal pad interfaces directly to a heatsink or cold plate.
推荐
Battery Protection and Power Path Management
For 12 V battery management systems and power-path OR-ing in industrial UPS or e-mobility charging infrastructure, the IQEH50NE2LM7UCGSCATMA1 can be used as a low-loss disconnect FET. Its 0.5 mΩ RDS(on) minimizes steady-state voltage drop across the protection element, and the 25 V VDS comfortably exceeds 12 V battery transients. The PG-WHTFN-9-1 package provides mechanical robustness and good thermal performance for continuous conduction in power-path circuits.
推荐
推荐产品汇总
工程参考数据： IQEH50NE2LM7UCGSCATMA1 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | IQEH50NE2LM7UCGSC | IQE220N15NM5CGSCATMA1 | BSC014NE2LSIATMA1 | ISC037N12NM6ATMA1 | ISC015N06NM5LF2ATMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-WHTFN-9-1 | PG-WHTFN-9-1 | PG-WHTFN-9-1 | PG-WHTFN-9-1 | PG-WHTFN-9-1 | PG-WHTFN-9-1 |
| VDS Max | 25 V | 25 V | 150 V | 25 V | 120 V | 60 V |
| RDS(on) Max | 0.5 mΩ | 0.5 mΩ | 22 mΩ | 1.4 mΩ | 3.7 mΩ | 1.5 mΩ |
| Continuous ID @ TA | 54 A | 54 A | 55 A | 40 A | 46 A | 55 A |
| PD @ TC | 150 W | 150 W | 150 W | 89 W | 83 W | 104 W |
| Max Junction Temp | 175 °C | 175 °C | 175 °C | 150 °C | 175 °C | 175 °C |
| Technology Generation | OptiMOS 7 | OptiMOS 7 | OptiMOS 5 | OptiMOS 2 | OptiMOS 6 | OptiMOS 5 LF2 |
| Target Application | AI / Data Center PoL | AI / Data Center PoL | Industrial HV | Server VRM | Industrial MV | Server / PoL |
关键差异点
- Lowest RDS(on) in the Infineon 25 V OptiMOS 7 PG-WHTFN family （对比 BSC014NE2LSIATMA1)
- 25 V VDS optimized for 12 V synchronous rectification （对比 IQE220N15NM5CGSCATMA1)
- OptiMOS 7 generation with 175°C junction rating （对比 ISC015N06NM5LF2ATMA1)
设计说明
Estimated: At continuous drain current of 54 A at TA and 422 A pulsed at TC, the IQEH50NE2LM7UCGSCATMA1 dissipates substantial heat in the PG-WHTFN-9-1 package. Infineon's datasheet characterization uses a 40 mm × 40 mm × 1.5 mm FR4 PCB with 6 cm² of 70 µm copper for the drain. For full SOA utilization, follow this minimum copper area and connect the top-side thermal pad to a copper pour or cold plate with multiple thermal vias.
Use a Kelvin-source gate drive connection to fully realize the 0.5 mΩ RDS(on) specification; sharing the source bond wire between gate-drive return and high-current return path adds ~0.2-0.4 mΩ of effective resistance and degrades efficiency at high current. Place the gate-driver and gate resistor within 5 mm of the gate pad to minimize the gate-drive loop inductance, which directly controls switching loss.
Estimated: With 2.5 W PD at TA, the package can dissipate in still air on a moderate PCB; at the 150 W TC rating, the package requires significant cooling. Use the datasheet SOA diagram to verify operation under worst-case load transients, and de-rate below 175°C maximum junction temperature - a 25-30°C margin is recommended for production reliability per typical power-electronics design practice.
Do not parallel this part with significantly different RDS(on) without adequate gate-source resistor balancing; OptiMOS 7 has positive temperature coefficient of RDS(on), but threshold voltage variation between parallel units can still cause current imbalance. Verify peak drain current under worst-case operating conditions (input surge, output short, hot-swap) against the SOA. Confirm 25 V VDS headroom above maximum bus transients in your system.
合规信息
RoHS and lead-free status inferred from Infineon OptiMOS 7 standard product compliance per product page; AEC-Q100 automotive grade not stated in the verified distributor listings.
