Amplifier ICs
بەرهەمەکان (3,200+)
LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi
The onsemi LM2903DMR2G is a dual independent precision voltage comparator with 2 mV typical input offset voltage, 1.3 us typical response time, and a wide 2 V to 36 V supply range, housed in an 8-pin MSOP (Micro8) surface-mount package. A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators form the lowest tier of the amplifier IC hierarchy (comparator -> amplifier IC -> analog signal chain IC -> semiconductor) and differ from op-amps by their open-collector outputs and fast, unsaturated switching behavior. The LM2903 belongs to the industry-standard LM393 comparator family, which has been the default choice for level detection, threshold monitoring, and limit sensing across consumer, automotive, and industrial electronics for decades. Key features include low input offset voltage as low as 2.0 mV, input common-mode range extending down to ground (V-) level even under single-supply operation, low supply current of approximately 700 uA per package, and open-collector outputs compatible with TTL, MOS, and CMOS logic levels. The wide 2 V to 36 V single-supply range (or equivalent split-supply operation) allows direct connection to automotive 12 V and industrial 24 V rails without preconditioning. Architecturally, the device integrates two fully independent comparator channels that share only the supply pins, permitting simultaneous use without channel-to-channel interaction. The open-collector output stage requires an external pull-up resistor, which lets designers set the logic interface level independently of the supply - a 5 V pull-up on a 12 V-powered comparator interfaces directly with TTL logic. Typical applications include limit comparators and threshold detectors in power supplies, window comparators in battery chargers and over-voltage protection circuits, sensor conditioning for industrial automation, and level translation and oscillator timing circuits in consumer electronics. A key design consideration: because the output is open-collector, forgetting the pull-up resistor produces a permanently floating output; select the pull-up value for the required rise time and sink current, typically 3 k to 15 k. Also keep input differential voltage within the absolute maximum rating. This page consolidates verified electrical specifications, drop-in alternatives, application guidance, and practical design notes not found in a single manufacturer document.
LM2903DR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)
The Texas Instruments LM2903DR is a dual differential analog comparator with two independent comparator channels, an operating supply range of 2 V to 36 V, a response time of 300 ns, and an 8-pin SOIC package. Each channel provides open-collector output behavior for level translation, relay driving, and wired-AND logic functions. The device is specified for operation from -40 °C to +125 °C according to the available manufacturer comparison data. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2903DR belongs to the comparator hierarchy within analog and mixed-signal semiconductors, providing a simple alternative to an operational amplifier configured as a comparator. Its two channels operate independently, allowing one package to implement two threshold decisions or to control complementary functions in a single circuit. The open-collector outputs are a defining electrical feature. Each output transistor can pull its output low, but it cannot actively drive the output high, so an external pull-up resistor is required. Multiple open-collector outputs can share one pull-up to create a wired-AND arrangement. This architecture also provides a useful form of output isolation while remaining compatible with standard 5 V and 3.3 V digital logic levels when the pull-up rail is selected appropriately. The 2 V to 36 V supply capability allows operation from low-voltage analog systems through conventional industrial control rails. Its 300 ns response time supports applications where decisions must be made faster than typical slow comparators but where nanosecond-level precision is unnecessary. The operating temperature range covers industrial environments, although production designs should still verify temperature-dependent input offset, output-current, and propagation-delay behavior using the selected manufacturer's complete datasheet. Typical uses include industrial sensor conditioning, battery monitoring, overvoltage detection, window or level comparators, relay and solenoid interfaces, and digital control systems that require open-collector outputs. The SOIC-8 package is also appropriate for through-hole-style PCB assembly and manual rework, although SOIC-8 is larger than modern comparator packages such as SOT-23 and MSOP-8 variants. When designing with the LM2903DR, always place the input and pull-up networks close to their associated pins, and account for input common-mode limits at the selected supply voltage. A pull-up resistor is not optional because the open-collector output cannot source current. Reviewing the voltage drop across the pull-up and the output transistor's current rating is essential when several outputs share the same node. This page consolidates verified distributor listings, manufacturer references, pin-compatible alternatives, package details, and practical circuit guidance. It also distinguishes directly interchangeable devices from higher-speed or higher-precision alternatives whose electrical behavior may require different design assumptions.
LM2903DR2 - Dual 36 V Comparator | onsemi | SOIC-8
onsemi LM2903DR2 is a dual differential voltage comparator designed for single-supply or split-supply operation between 2 V and 36 V. The device contains two independent comparison channels, supports a common-mode input range extending to ground in single-supply systems, and is packaged in an 8-pin SOIC. Its open-collector output architecture provides flexible interface options for wired logic, pull-up networks, relay drivers, and systems operating from multiple supply rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its primary role is threshold detection rather than linear amplification. Two independent channels allow one package to implement two unrelated sensing functions while sharing a common supply connection and ground reference. The LM2903 series combines low input-offset voltage, low input-bias current, and a wide supply-voltage range. Input offset voltage is specified as low as 2.0 mV, which helps define the input-voltage difference required to change output state. The 2 V to 36 V operating range supports legacy 5 V logic, industrial 12 V and 24 V rails, automotive-style 12 V systems, and higher-voltage threshold-detection circuits. The open-collector outputs permit an external pull-up voltage to be selected independently of the comparator supply. Each channel compares a non-inverting input with an inverting input. When the non-inverting voltage is higher, the corresponding open-collector output transistor turns on and pulls the output toward the pull-up rail; when the inverting voltage is higher, the transistor turns off and the output rises. The two channels are independent, although their supply and ground pins are shared. This arrangement supports sensor thresholding, window detection, and complementary decisions without requiring two separate packages. Typical uses include industrial control and factory automation, battery-powered monitoring, automotive battery and power-system detection, instrumentation, protection circuits, and embedded systems using 3.3 V or 5 V microcontroller interfaces. For digital interfaces, the open-collector output can use a pull-up to the logic rail used by a comparator input or microcontroller. The SOIC-8 package also supports conventional surface-mount assembly and hand-soldering workflows. Designers should verify the allowable input and output voltage relationships, including the differential input range, and use a pull-up resistor that supplies adequate output current without exceeding the output transistor's limits. Care is also needed when a channel drives a cable, relay, or large capacitance because slower edges and parasitic coupling can affect system behavior. The input network should include suitable filtering when the sensed signal contains switching noise. This product overview combines the exact LM2903DR2 ordering identity with practical guidance on comparator operation, pin usage, output interfacing, and verified drop-in options. It is intended to support component selection, PCB replacement, and design reviews involving dual open-collector comparators in SOIC-8 packages.
LM2903DR2G - Dual 36V Open-Collector Comparator | onsemi
onsemi LM2903DR2G is a dual differential voltage comparator with two independent comparator channels, 2 V to 36 V supply operation, open-collector outputs, 1.5 µs propagation delay, and an 8-pin SOIC package. The device also supports split-supply operation with stated rails from ±1 V to ±18 V and an input offset voltage as low as 2.0 mV. A dual comparator is a semiconductor that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the broader voltage-comparator hierarchy within analog integrated circuits and power-management signal conditioning. Its two independent channels allow simultaneous or separate threshold, window, sensing, and level-detection functions without requiring two separate comparator packages. Key features include two open-collector channels, a 1.5 µs response time, and low-offset operation with input offset voltage specifications as low as 2.0 mV. The 2 V to 36 V total supply range supports industrial, automotive-style, and embedded applications where the comparator may operate from a single supply or from positive and negative rails. Open-collector outputs permit external pull-up selection and can interface with TTL, MOS, or CMOS-compatible systems when the pull-up voltage and current are appropriate. The comparator architecture is appropriate when a design needs a digital decision rather than a linear analog output. Each channel can compare a sensed voltage against a reference threshold, while the open-collector structure allows wired logic, alarm signaling, or direct control of a pull-up-equipped input. Operation from single or split supplies expands its usefulness in power systems that use both positive and negative reference rails. Typical applications include automotive battery and power-rail monitoring, industrial control thresholds, motor and actuator interfaces, sensor conditioning, overvoltage and undervoltage detection, and embedded system supervision. The 8-SOIC package provides a conventional surface-mount footprint, while the dual-channel configuration helps reduce component count in dual-threshold or multi-channel sensing designs. Designers should verify input common-mode limits, output pull-up values, differential input limits, and the exact electrical grade associated with the selected ordering code. Keep output pull-up paths short, provide adequate return-current routing, and account for the open-collector output’s tendency to sink current rather than source it. The Request a Quote form on this page supports current commercial sourcing questions. This page organizes the LM2903DR2G electrical characteristics, package information, drop-in candidates, comparison parameters, and practical circuit-placement guidance. It also identifies which ordering variants are technically suitable for footprint reuse and where direct replacement requires additional engineering review.
LM2903DRE4 - Dual 2-36V Comparator | Texas Instruments
Texas Instruments LM2903DRE4 is a dual differential voltage comparator with open-collector outputs, rail-to-rail input capability, a 2 V to 36 V supply range, and an 8-pin SOIC package. Each channel can operate independently, making the device suitable for threshold detection, level translation, window monitoring, and industrial control tasks. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when one input crosses the other. A dual comparator contains two electrically independent comparator channels in one package. The LM2903 belongs to the voltage comparator hierarchy, where it can be described more specifically as a differential comparator with open-collector outputs. It operates from a single supply or from split supplies, making it suitable for industrial power systems with widely separated ground references. The principal advantages of the LM2903DRE4 are its broad 2 V to 36 V operating supply range, rail-to-rail input characteristic, low typical supply-current drain of 0.4 mA per comparator, and 300 ns response time. The two open-collector outputs allow the output state to be pulled up to an external voltage and provide wired-AND behavior when several comparators share a pull-up resistor. This output arrangement is useful when interfacing with open-drain logic, relay drivers, or subsequent CMOS and TTL stages. Each comparator contains independent input and output circuitry. Differential input voltage is evaluated between the inverting and noninverting inputs, and the output transistor is turned off or on according to that relationship and the polarity of the open-collector stage. Because the outputs are open collector, the output voltage depends on the pull-up network rather than the comparator alone. Designers must account for leakage current, pull-up resistance, logic thresholds, and propagation delay when translating a high-impedance output state into a valid digital level. Typical uses include industrial sensor thresholds, battery and power-supply monitoring, overvoltage detection, motor-control signaling, and general-purpose logic interfacing. A split-supply arrangement can compare bipolar signals around ground, while a single-supply arrangement supports systems whose input common-mode range reaches the lower supply rail. The 8-pin SOIC package also supports conventional surface-mount assembly and easy routing between two comparator channels. A key design consideration is that open-collector outputs require an external pull-up resistor. Select that resistor so that its maximum current and the output leakage current still produce a valid high level, while keeping rise time consistent with the required system response. The 300 ns propagation delay is important for high-speed threshold decisions, but slower pull-up networks can add additional delay after the comparator changes state. This page combines manufacturer and distributor information with package guidance, application analysis, cross-brand substitution notes, and engineering-focused design advice to help evaluate the LM2903DRE4 beyond a basic catalog listing.
LM2903DRG3 - Dual Open-Collector Comparator | Texas Instruments
The Texas Instruments LM2903DRG3 is a dual differential comparator with open-collector outputs, operating from 2 V to 36 V on a single supply or ±1 V to ±18 V on dual supplies, in an 8-pin SOIC package. Each of the two independent comparator channels draws 200 µA of supply current and offers a 1 µs response time, making the LM2903DRG3 a standard general-purpose comparator for industrial, automotive and instrumentation signal chains. A comparator is a differential amplifier whose output is driven to a logic state when one input exceeds the other by more than the input offset voltage. It belongs to the amplifier IC family, sits under the operational amplifier hierarchy, and ultimately falls inside the linear and signal-conditioning IC category. Unlike an op-amp, a comparator has no linear output region and is not intended for open-loop gain; its open-collector output is designed to pull a rail low and to be pulled up externally, which allows it to sink more current than a CMOS push-pull output can. Key features include a maximum rated supply of up to 38 V, an ESD rating of 2 kV HBM, a low input offset voltage of 0.37 mV and a low input bias current of 3.5 nA, all of which improve threshold accuracy and reduce source loading on the sensed signal. The differential input voltage range is equal to the maximum rated supply voltage at ±38 V, and the common-mode input voltage range includes ground, allowing the device to monitor bipolar signals referenced to 0 V. Outputs are compatible with TTL, MOS and CMOS logic families. Electrically the device is a bipolar dual differential comparator with an open-collector output stage. The open-collector architecture means the output can be pulled to any supply level the system uses, and a pull-up resistor sets the high level. This is essential in relay-drive, lamp-drive and level-shifting designs where the load requires more current than the IC itself can source. Typical applications include industrial sensor threshold detection, battery and rail window comparison, overvoltage and undervoltage protection in power supplies, temperature monitoring with thermistors or RTDs, and current-sense comparison in motor drive and inverter control stages. When designing with the LM2903DRG3, always place the pull-up resistor close to the output pin and check that the total sink current stays within the output rating, because the open-collector transistor, not the internal drive, sets the load capability. This page consolidates parametric data, drop-in alternatives, comparison tables and practical design notes so engineers can evaluate the LM2903DRG3 against equivalent dual comparators without rebuilding the analysis from scratch.
LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments
Texas Instruments LM2903DRG4 is a dual differential voltage comparator with an open-collector output, supplied in an 8-pin SOIC package. It operates from a single supply over a 2 V to 30 V range, or from dual supplies when the total supply difference remains within 2 V to 36 V. The device contains two independent comparators, making it suitable for threshold detection, window comparison, and industrial control functions. The LM2903 is a general-purpose comparator within the broader category of analog comparator ICs. A comparator evaluates two input voltages and produces a logic-level result indicating which input is higher. In an open-collector implementation, the output stage can sink current while remaining in a high-impedance state when the device is inactive. This architecture allows external pull-up resistors to set the output voltage and interface with TTL, MOS, or CMOS logic. Key characteristics include a 2 V to 30 V supply range for the non-V device, a 30 V maximum supply rating, approximately 1.3 microsecond propagation delay, and typical supply-current drain of approximately 0.4 mA per comparator. The input common-mode range includes ground, and the differential input voltage range is equal to the maximum-rated supply voltage at ±38 V for the versions described by the manufacturer. The open-collector outputs require pull-up resistors when connected to digital logic. The outputs are intended to sink rather than source output current, so the pull-up resistor value determines the rise time, power consumption, and compatibility with the receiving logic. The wide supply range and low-power operation make the LM2903 suitable for process control, power supervision, sensor conditioning, and general-purpose threshold detection. When designing around the LM2903, verify the supply limits, common-mode input range, differential input limits, output pull-up network, and the switching behavior required by the downstream circuit. The device is a dual comparator, so each channel is independent, but both channels share the same supply pins and package footprint. The SOIC-8 format supports conventional surface-mount assembly and provides a practical upgrade path from through-hole comparator designs when the pin configuration is verified. This page brings together the manufacturer product information, verified distributor references, package details, drop-in comparison options, and application guidance for engineers evaluating the LM2903DRG4 in new analog-control and embedded-system designs.
LM2903FVJ-E2 - Dual Ground-Sense Comparator | ROHM Semiconductor
ROHM Semiconductor LM2903FVJ-E2 is a dual-channel, general-purpose ground-sense comparator with open-collector outputs and a 3 V to 32 V operating supply range. The device is packaged in an 8-pin TSSOP-B8J package and is supplied in tape-and-reel packing. ROHM lists the LM2903FVJ as Not Recommended for New Designs, so the part is best evaluated for existing designs, maintenance, and previously qualified industrial equipment rather than new product creation. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. The dual architecture provides two comparison channels in one package, reducing component count when a board needs independent threshold decisions. The LM2903FVJ-E2 is intended for ground-sense applications, where a comparator evaluates a signal relative to a ground-referenced threshold and drives an open-collector output. Open-collector outputs allow wired-AND behavior when several outputs share a pull-up resistor, which is useful in alarm, interlock, and system-fault signaling circuits. The key operating characteristics are the 3 V to 32 V supply range, two comparator channels, ground-sense input arrangement, and open-collector output architecture. The broad supply range allows the device to operate from conventional 5 V and 12 V industrial rails as well as higher-voltage systems, subject to the limits in the manufacturer datasheet. Its open-collector output stage requires an external pull-up resistor when a logic-high output is required. The output should not be assumed to drive a load directly; the pull-up resistor, downstream logic input, and fault-state behavior must be checked together. Typical uses include overvoltage and undervoltage indication, ground-fault detection, battery or power-supply monitoring, industrial control interlock logic, threshold-based signal conditioning, and general embedded control. The comparator can operate directly from higher-voltage rails, but the input pins, output pull-up network, grounding, and protection network must remain within their specified limits. External filtering or clamping may be required when the monitored signal contains transients or exceeds the input common-mode range. Designers should review the ROHM datasheet for the complete electrical limits, input common-mode range, output sink-current capability, response-time behavior, and package details before release to production. Because the manufacturer marks the LM2903FVJ as Not Recommended for New Designs, a responsible product decision should compare current ROHM alternatives rather than treating this part as the preferred choice for a fresh design. Existing production equipment may still benefit from a qualified replacement strategy when availability, lifecycle status, and electrical compatibility are reviewed. This product summary consolidates the manufacturer product identity, package information, lifecycle status, operating-range information, practical application guidance, and sourcing questions into one engineering reference. It is intended to support initial part identification, circuit review, and replacement planning without replacing the complete manufacturer datasheet.
LM2903FVT-E2 Dual Ground-Sense Comparator | ROHM
ROHM Semiconductor LM2903FVT-E2 is a dual-channel ground-sense comparator with open-collector outputs, a 3 V to 32 V operating-voltage range, and low supply current. The device is supplied in an 8-pin TSSOP-B surface-mount package for compact industrial and automotive electronic systems. Its two independent comparator channels compare input signals against ground-sensitive thresholds and drive open-collector outputs suitable for pull-up-based interfacing. A comparator is an analog integrated circuit that evaluates one input voltage relative to another and changes its output state when the relationship between those voltages crosses a defined threshold. The LM2903 series belongs to the broader open-collector comparator hierarchy, which combines analog signal conditioning, threshold detection, and digital-compatible output signaling. Ground-sense operation is particularly useful when the reference or monitored signal is referenced to the system ground rather than to a mid-supply rail. The principal features of the LM2903FVT-E2 include two comparator channels, a wide 3 V to 32 V supply range, low supply current, and open-collector outputs. The open-collector architecture allows the output transition speed to be influenced by an external pull-up resistor and load capacitance. This flexibility makes the device suitable for wired logic, relay or solenoid interfaces, threshold monitoring, and systems where the pull-up voltage must be selected independently from the comparator supply. The wide operating-voltage range allows the comparator to operate from low-voltage 3 V systems through substantially higher supply rails, subject to the absolute maximum ratings and application conditions defined by the manufacturer. Because each channel uses an open-collector transistor, an external pull-up resistor is required to establish a valid high output level. The pull-up voltage, resistor value, allowable sink current, and rise time should be selected together according to the required operating frequency and connected load. Typical applications include automotive and industrial control modules, battery-powered equipment, overvoltage and undervoltage detection, sensor-threshold conditioning, window or level detection, and general digital control systems. The low supply-current characteristic is particularly relevant to systems that maintain operation across a broad supply range without continuously operating from a tightly regulated rail. The TSSOP-B package supports compact layouts, although careful PCB planning remains necessary for clean signal routing. For reliable implementation, connect the required pull-up resistor to the pull-up supply, keep comparator input traces short, and avoid routing high-current or fast-switching paths near the input pins. Confirm the input common-mode limits, differential input limits, output current, and supply decoupling requirements against the manufacturer datasheet for the selected automotive and temperature grades before production release. This product record combines the manufacturer product description with distributor packaging information and practical guidance for comparator implementation, PCB integration, output pull-up design, and drop-in replacement assessment. It also distinguishes verified ordering information from engineering assumptions so engineers can review the circuit and manufacturing implications before selecting a comparator for a new design.
LM2903HD - Dual 36V Open-Collector Comparator | STMicroelectronics
STMicroelectronics LM2903HD is a low-power dual differential voltage comparator designed for single-supply operation from 2 V to 36 V or dual-supply operation from ±1 V to ±18 V. Each channel provides an open-collector output, and the device is supplied in an 8-pin SOIC package with tube packing. The LM2903HD combines two independent comparators in one package for threshold detection, level translation, window sensing, and general-purpose signal conditioning. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its open-collector outputs can sink current from a pull-up network, making the device suitable for wired logic, relay drivers, and interface applications where the output must connect to another supply domain. The STMicroelectronics LM2903 datasheet identifies a wide supply range of 2 V to 36 V under single-supply operation and ±1 V to ±18 V under dual-supply operation. It also specifies low supply-current drain independent of supply voltage and a typical drain of 0.4 mA per comparator. These characteristics allow economical operation from industrial, automotive, and embedded supply rails while preserving useful input and output operating ranges. The differential input arrangement places the inverting and non-inverting terminals on separate comparator channels. When the voltage applied to the non-inverting input exceeds the corresponding inverting input, the associated open-collector output transitions according to the comparator's polarity. External resistors normally define the output high state because an open-collector transistor actively pulls the output low but does not source a sustained output voltage. Typical LM2903HD applications include DC threshold detection, battery-voltage monitoring, sensor signal conditioning, window comparators, and logic-level translation. The dual-channel configuration reduces component count in circuits requiring two independent comparisons. Its open-collector outputs also support wired-AND behavior when multiple comparator outputs share a pull-up resistor. PCB design should keep comparator inputs and feedback components away from switching nodes and high-current return paths. Place input resistors and feedback resistors close to the device, use a solid ground reference, and add supply bypassing where required by the implementation. Validate output pull-up values against sink-current limits, propagation delay, and the required logic rise time. This product page combines manufacturer specifications, ordering information, package details, application guidance, and pin-compatible comparison information. It is designed to help engineers identify the LM2903HD quickly, verify its electrical limits, and select an appropriate second source without changing the PCB footprint.
LM2903HYPT - Dual Open-Collector Comparator | STMicroelectronics
The STMicroelectronics LM2903HYPT is a low-power dual differential voltage comparator with two open-collector outputs, a 2 V to 36 V single-supply range, and an 8-TSSOP package. Each comparator operates from dual supplies of ±1 V to ±18 V, responds in 1.3 µs typically, and draws 0.4 mA per comparator. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903HYPT belongs to the comparator hierarchy within analog ICs and interface electronics. Its differential inputs suit threshold, window, overvoltage, and sensor-conditioning circuits, while the open-collector outputs allow wired AND operation, level translation, or pull-up-based interfacing. Each channel offers a typical input offset voltage of 1 mV, input offset current of ±5 nA, and input bias current of 25 nA. The input common-mode range includes ground, making the device useful in single-supply systems in which signals approach the lower supply rail. Output saturation voltage is 250 mV typical with 4 mA output current, and the outputs are compatible with DTL, TTL, CMOS, ECL, and MOS logic families. The two independent comparators operate over a −40 °C to +150 °C temperature range. The HYPT ordering code places the device in an 8-TSSOP package supplied in tape-and-reel format. Its automotive qualification and RoHS-compliant construction support demanding industrial, automotive, and sensing applications where low input bias, wide supply range, and open-collector interface flexibility are important. Typical uses include battery-powered monitoring, industrial sensor interfaces, overvoltage protection, control-loop threshold detection, and open-drain alarm signaling. The 36 V maximum single-supply operation also permits direct monitoring of higher-voltage systems when the input and supply ratings are respected. For reliable implementation, place input and output traces away from fast-switching nodes, provide a pull-up resistor on each open-collector output, and verify common-mode, differential-input, and output-current limits against the manufacturer datasheet. The low input bias current helps preserve sensor accuracy, while the open-collector output requires an external pull-up. This page combines exact operating specifications, pin-level implementation guidance, application analysis, and package-compatible replacement information to support faster design-in and sourcing decisions.
LM2903ITLX/NOPB - Dual Low-Power Open-Collector Comparator, 8-DSBGA
The Texas Instruments LM2903ITLX/NOPB is a dual, low-offset, open-collector differential comparator in an 8-ball DSBGA package, with two independent comparator channels operating from a single supply between 2 V and 36 V. Each channel offers an input offset voltage as low as 2.0 mV maximum for the LM193-series family, an input bias current of 0.25 uA maximum at 5 V, a typical output sink current of 16 mA at 5 V, and a propagation delay of 700 ns maximum. A comparator is a differential input amplifier whose output switches state when one input exceeds the other by more than the offset voltage. Comparators sit at the bottom of the analog signal chain as the decision element that converts a small analog difference into a logic-level event. The LM2903 belongs to the LM193/LM2903/LM393 family, a classic general-purpose voltage comparator family, and this device adds a low-power, wide-supply differential pair plus a saturating open-collector transistor output stage. Key features of the LM2903ITLX/NOPB include open-collector outputs that can be pulled up to any logic level up to the supply rail, differential input range of plus or minus 18 V, common-mode input voltage range that includes ground, an industrial temperature grade of -40 C to +85 C, and total quiescent current of 2.5 mA maximum for the pair. The open-collector architecture allows multiple comparators to be wire-ORed on a shared pull-up resistor, which is the standard technique for driving slow, high-voltage relay, lamp, or open-drain bus loads. Internally the device is a bipolar dual-diff-pair design with an emitter-stabilized differential input stage feeding a saturated open-collector output transistor. Because the output stage is open collector rather than push-pull, output rise and fall times are set by the pull-up resistor and the load capacitance rather than by an internal driver, which allows a designer to trade speed for EMI margin. The wide 2 V to 36 V supply span lets a single part sense signals referenced to either a low-voltage logic rail or a 24 V industrial bus. Typical applications include over/under-voltage and window monitoring in power supplies, sensor threshold conditioning for industrial and automotive sensing chains, zero-cross and level detection in motor control and drive electronics, open-drain bus arbitration in multi-drop industrial networks, and general-purpose analog signal conditioning where an open-collector output must drive a relay or an opto-isolator. Design consideration: because the outputs are open collector, an external pull-up resistor is mandatory, and its value sets the output rise time. Keep pull-ups high enough to limit sink current within the 16 mA typical output rating, and low enough to achieve the required switching speed with the total bus capacitance. This page consolidates parametric detail, drop-in alternatives for the same 8-DSBGA footprint, and practical layout and pull-up guidance that is not assembled in one place in the original LM2903 documentation.
LM2903M/NOPB - Dual Open-Collector Comparator | Texas Instruments
The Texas Instruments LM2903M/NOPB is a dual differential analog comparator with two independent channels, low offset voltage, and open-collector outputs in an 8-pin SOIC package. According to the manufacturer product information, the device supports a single-supply operating range extending to 18 V and an operating temperature range of -40°C to 85°C. Its maximum input offset voltage is specified as low as 2 mV, while input current values of 2 nA and 5 nA appear in the product listing. An analog comparator is a signal-conditioning semiconductor that compares two input voltages and changes its output state when one input exceeds the other. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. A differential comparator can operate from a single supply or split supply, allowing it to compare signals near ground, bipolar signals, or thresholds referenced to a supply rail. The LM2903M/NOPB provides two independent low-power, low-offset comparators in one package. Its open-collector outputs are designed for wired-interface use and require an external pull-up resistor to establish a positive logic high when the output transistor is off. The listed propagation delay is 1.5 microseconds, making the device suitable for threshold detection, level translation, relay or solenoid driving, and general industrial control functions where microsecond-scale decision speed is sufficient. A broad supply range is useful in equipment operating from industrial or automotive-style voltage rails. The -40°C to 85°C temperature range supports industrial and extended-temperature environments, although the specific LM2903M/NOPB orderable status and quality qualification should be checked for each deployment. The 8-pin SOIC package is a standard surface-mount footprint that is larger than contemporary compact packages but remains convenient for hand assembly, prototyping, and through-hole-style external pull-up routing. Typical uses include monitoring a sensor against an adjustable threshold, detecting overvoltage or undervoltage conditions, converting an analog level into a logic event, and providing two independent comparisons in control, instrumentation, or power-supply systems. Because the outputs are open collector, multiple devices or nodes can share a pull-up arrangement when the electrical conditions permit. Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and the effect of input bias current when selecting threshold resistors. Keep comparator inputs away from switching-node currents and provide a stable local ground reference. The open-collector nodes should have pull-up resistors selected for the required logic voltage, sink-current budget, rise-time target, and system power budget. This page combines the manufacturer's ordering information, a source-grounded parameter summary, application engineering guidance, and package-level replacement analysis. It also identifies the design trade-offs that matter when comparing the LM2903M/NOPB with related dual comparators rather than relying only on basic device descriptions.
LM2903M/SL160222 - Dual Differential Comparator | Texas Instruments
The Texas Instruments LM2903M/SL160222 is a dual differential comparator containing two independent precision voltage comparators in an 8-pin SOIC package. It supports single-supply operation, provides an input offset voltage specification as low as 2.0 mV maximum for two comparators, and uses open-collector outputs. The device is intended for general-purpose signal comparison, threshold detection, industrial control, and interface applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category sits within analog signal-processing ICs, alongside amplifiers and voltage references, while remaining distinct from a general-purpose operational amplifier. The LM2903 architecture combines two independent channels in one package, reducing board area when two comparison functions are required. The LM2903 family is designed to operate from a single power supply over a wide voltage range. According to the manufacturer datasheet, the offset voltage can be specified as low as 2.0 mV maximum for the two-comparator configuration. Open-collector outputs permit wired connections to pull-up circuitry and provide a flexible interface to TTL, MOS, and CMOS-compatible systems. Each channel offers separate inverting, non-inverting, and output terminals. Because the two sections are electrically independent, engineers can use one channel for a sensor threshold and the second for a system interlock or control signal. The single-supply architecture is useful in equipment where one supply rail defines the comparator signal domain. Input and output operating conditions, channel-to-channel behavior, supply-current characteristics, and absolute maximum ratings should be checked against the exact manufacturer ordering information before production release. Typical applications include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, motor-control logic, window comparators, and digital threshold conditioning. In each case, open-collector outputs can drive a pull-up and logic gate, or serve as an active-low alert signal. The small SOIC footprint also supports compact control boards where two independent channels are valuable. For robust layouts, route comparator inputs away from switching nodes and power inductors, place input-referred bypassing close to the supply pin, and pull each open-collector output up to the appropriate logic supply. Check that the pull-up voltage, input common-mode range, supply voltage, and output sink-current requirement satisfy the application before substituting this part into an existing design. This page consolidates the exact LM2903M/SL160222 ordering information, verified manufacturer and distributor references, pin assignments, drop-in alternatives, and practical application guidance to accelerate schematic review, PCB reuse, sourcing, and replacement planning.
LM2903MX - Dual Differential Comparator | Texas Instruments
Texas Instruments LM2903MX is a dual differential analog comparator containing two independent general-purpose comparator channels in an 8-pin SOIC package. Each channel supports single-supply operation from 2 V to 36 V or dual-supply operation from 1 V to 18 V, and the device includes rail-to-rail input capability, an open-collector output, and a typical response time of 1.3 us. The open-collector outputs are compatible with CMOS, MOS, and TTL logic. An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state according to their relative polarity. Within the semiconductor hierarchy, a comparator belongs to the broader group of analog ICs and serves as an interface between sensors and digital logic. The LM2903MX is useful when a design needs to detect crossings, thresholds, overvoltage, undervoltage, or differences between two analog signals without converting them into a digital quantity. The two channels operate independently, allowing one device to implement two unrelated threshold functions. Key features include comparison of input voltages near ground potential, a wide supply range, low current drain, and open-collector outputs that require an external pull-up resistor. Rail-to-rail input behavior is particularly valuable when the signal of interest lies close to either supply rail. The specified 1.3 us response time makes the comparators appropriate for power-line, protection, sensing, and general signal-conditioning circuits. Typical uses include monitoring a divided battery voltage, detecting an over-temperature condition with a sensor, comparing an adjustable reference with an analog input, and translating a sensor threshold into a logic-level event. The open-collector topology also allows several comparator outputs to share a wired bus when each output has a suitable pull-up and the system design accounts for the resulting behavior. PCB implementation should follow the manufacturer pin-description table and place input, output, and decoupling connections to minimize switching noise. Input traces should be kept short and away from high-current paths. Use a pull-up resistor sized for the target logic family, and verify its maximum current across all operating conditions. Do not substitute a push-pull output device without reviewing the full pinout and signal behavior. This page compares the LM2903MX with documented same-footprint alternatives, summarizes verified electrical and package characteristics, and adds practical PCB, logic-interface, and replacement guidance for engineers evaluating this dual comparator.
LM2903MX-ON - Dual Open-Collector Comparator | onsemi
The onsemi LM2903MX-ON is a dual open-collector voltage comparator for single-supply or split-supply operation, housed in an 8-pin SOIC package. It provides two independent comparator channels, a common-mode input range extending to ground during single-supply operation, and input offset voltage as low as 2.0 mV. The device supports supply voltages from 2 V to 36 V and is specified for an operating temperature range of -40°C to +85°C. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output when the difference crosses a specified threshold. The LM2903 family belongs to the comparator hierarchy, which sits within analog and mixed-signal semiconductors used for threshold detection, sensing, and control. Its two channels can operate independently from a shared supply, allowing one device to implement two comparison functions in a compact footprint. The primary features of the LM2903MX-ON are its dual-channel architecture, open-collector outputs, wide operating supply range, and low-offset capability. Open-collector outputs permit an external pull-up resistor to establish the output logic level. This arrangement supports wired-AND behavior and allows interface levels to be selected by changing the pull-up supply rather than relying on a dedicated output-supply pin. Each internal comparator has two inputs and one output. With single-supply operation, the common-mode input range can include ground, making the device useful for monitoring signals near 0 V. Split-supply operation permits comparison around a midpoint reference. Because the two channels are independent, they can compare separate sensor or threshold pairs while sharing the same package and supply architecture. Typical applications include industrial sensor interfaces, battery and power-system monitoring, control-loop threshold detection, window comparison, and general-purpose digital conditioning. The dual channel reduces board area when two independently referenced signals must be evaluated. The open-collector architecture is especially useful where the output must drive a pull-up rail, connect to a wired logic bus, or interface with a microcontroller input. PCB design should reserve a pull-up resistor for each open-collector output and route the input and output paths away from high-current switching nodes. The wide 2 V to 36 V supply range supports both low-voltage systems and higher industrial rails, but input and output operating conditions must remain within their respective absolute maximum ratings. This product page combines the LM2903MX-ON technical characteristics, verified manufacturer information, pin-level guidance, drop-in alternatives, and practical design considerations. These engineering details help shorten component selection and support direct PCB, sourcing, and lifecycle planning for dual-comparator designs.
LM2903MX/NOPB - Dual Open-Collector Comparator | Texas Instruments
Texas Instruments LM2903MX/NOPB is a dual differential analog comparator with two independent comparator channels, low offset voltage, open-collector outputs, and rail-to-rail input capability in an 8-pin SOIC package. The device is intended for low-power applications operating from a single supply or split supplies, with a manufacturer-specified operating temperature range of -40°C to 85°C for this ordering variant. An analog comparator is a semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the broader voltage comparator hierarchy, where each channel can evaluate a non-inverting input against an inverting input. Its open-collector outputs can sink output-stage current while leaving the output otherwise undriven in the high state, allowing a pull-up resistor to establish the logic-high voltage and support wired logic or level translation. The LM2903 provides two independent comparators in one package. Its differential input arrangement is useful when a circuit must detect whether a measured voltage is above or below a reference threshold. The low-offset characteristic reduces the input-voltage difference required to change output state, which is valuable in sensing circuits where small signal changes must be resolved accurately. Open-collector outputs also provide flexibility when driving pull-up resistors to a supply selected by the system designer. The rail-to-rail input characteristic expands the usable common-mode range of the comparator, while the low-power architecture suits battery-powered and general-purpose industrial designs. Because the two channels are independent, one package can implement two threshold detections, window-limit functions, or separate monitoring functions. Common implementations include overvoltage detection, undervoltage indication, temperature or sensor threshold switching, and simple control-loop decisions around a regulated supply. Typical applications include industrial control boards, battery-powered instrumentation, sensor interfaces, power-supply supervision, and embedded systems requiring logic-compatible threshold decisions. The 8-pin SOIC package supports conventional surface-mount assembly and works well where moderate pin count and straightforward layout are priorities. It is also a familiar functional family for designs built around the LM2903, LM2903-N, and related dual-comparator platforms. When designing the circuit, choose the external pull-up resistor to establish a valid logic-high voltage and check that the intended sink current remains within the output-device limits. Keep comparator inputs away from switching-node edges where practical, and evaluate input bias-current effects when the source impedance is high. The open-collector architecture avoids an active push-pull output but requires correct pull-up selection for dependable logic levels. This product data combines the exact ordering information for LM2903MX/NOPB with practical guidance on pin use, logic interfacing, common-mode behavior, and drop-in alternatives. It also organizes the comparator’s electrical, environmental, package, and sourcing attributes for faster engineering selection and PCB planning.
LM2903N - Dual Voltage Comparator, Open-Collector, 8-DIP | TI/STMicro/onsemi
The LM2903N is a dual-channel low-offset voltage comparator supplied in an industry-standard 8-pin PDIP (DIP-8) through-hole package. It integrates two independent precision comparators with 2.0 mV typical input offset voltage, an open-collector output stage capable of swinging to the negative rail (ground-sense at single supply), and operates from a 2 V to 36 V single supply or ±1 V to ±18 V dual supply rail. The output transistor sinks up to 16 mA typical (6 mA minimum over temperature), making the part suitable for directly driving low-power relays, LEDs, and logic interfaces. A voltage comparator is an analog building block that compares two input voltages and produces a binary digital output; when the non-inverting input exceeds the inverting input, the output switches state. The LM2903N belongs to the LM393/LM2903 family - a long-standing industry standard introduced for low-power single-supply sensing, and it sits in the hierarchy: comparator -> analog comparator -> signal conditioning IC -> integrated circuit. Its open-collector architecture requires an external pull-up resistor (typically 10 kohm to VCC), which lets multiple comparators be wire-ORed together and lets the output pull to a different rail than the supply voltage. Key specifications include a 1.3 us typical response time at 5 V/2 mA, a 2.5 mV maximum input offset voltage (LM2903 grade), an input bias current of 25 nA typical, and ESD clamps on the inputs that tolerate human-body-model discharge. The device operates across the automotive-industrial -40 C to +125 C range (LM2903N suffix N designates the PDIP-8 package, not the temp grade). The LM2903's architecture uses a PNP input stage that gives the inputs an exceptionally wide common-mode range that includes the negative rail (ground), which is why single-supply ground-referenced sensing is its dominant application. The open-collector NPN output stage isolates the comparator logic from the load voltage; only the pull-up rail sets the high-level output. Typical applications include battery monitoring in 12 V/24 V automotive and industrial systems (window detectors, under-voltage cutoff), zero-crossing detectors for mains interfaces when paired with an optocoupler, line-receiver / level-shift interfaces between high-voltage analog and low-voltage logic, threshold alarms and signal-conditioning front-ends, and oscillator / relaxation-oscillator circuits. When designing with the LM2903N, observe one trade-off: open-collector outputs use a pull-up resistor that adds RC delay to the rising edge - at 10 kohm with 100 pF of trace capacitance, rise time is about 1 us. For high-speed logic interfaces downstream, size the pull-up conservatively or use a discrete or integrated push-pull comparator when sub-microsecond edge rates are needed.
LM2903N-NS - Dual Precision Comparator | onsemi
The onsemi LM2903N-NS is a dual, independent precision voltage comparator with open-collector outputs, supplied in an 8-pin PDIP package. It contains two separate comparator channels, an input offset voltage specified as low as 2.0 mV maximum for the LM193/LM2903 family, and operation from either a single supply or split supplies. Its single-supply common-mode capability extends down to ground, making it useful for systems that monitor signals referenced to the supply rail. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 family belongs to the broader comparator category within analog and mixed-signal semiconductors. Unlike an operational amplifier used primarily for linear amplification, each LM2903N-NS channel provides a binary decision function. The open-collector outputs permit wired logic, pull-up arrangements, level translation, and connection to external pull-up networks. The two internal channels are independent, allowing them to perform separate threshold, window, or protection functions without sharing signal paths. Low input offset is important when the two compared voltages are close, because excessive offset can shift the switching threshold and create errors in precision monitoring. The family was specifically designed for single-supply operation over a wide voltage range, while split-supply operation is also supported. Its supply-current drain is independent of the magnitude of the applied supply voltage. The LM2903N-NS combines two independent precision comparators in one through-hole package. Open-collector outputs require suitable pull-up resistors or suitable pull-up logic to establish a valid high output state. Because the output stage is open collector, multiple comparator outputs can be combined when the application supports wired-AND behavior and the electrical conditions remain within the device ratings. Common-mode input limits, supply voltage limits, output sink-current limits, and input-current limits must still be respected. Typical uses include industrial sensor interfaces, battery and power-system monitoring, control systems, threshold detection, overvoltage and undervoltage protection, and general digital logic interfacing. The dual-channel organization is especially useful when two independent thresholds must be monitored in the same circuit. A single package also reduces board area compared with two separate single comparators while retaining straightforward through-hole assembly. For reliable operation, connect unused comparator inputs to a defined potential so they do not float near the switching threshold. Place the input and output pull-up network close to the relevant pins, and check that the external pull-up voltage does not exceed the allowed output and supply limits. The comparator normally responds to an input crossing, so hysteresis or positive feedback may be needed to prevent repeated output transitions when the compared signals are nearly equal. This product page combines the family-level electrical description, package and pin information, sourcing guidance, compatible alternatives, and practical design notes. It also distinguishes true same-footprint replacements from alternatives that require PCB changes, helping engineers assess upgrade options before committing a design to production.
LM2903N/NOPB - 36V Dual Open-Collector Comparator | TI
Texas Instruments LM2903N/NOPB is a dual differential comparator with two independent channels, open-collector open-drain outputs, a 36 V maximum supply rating, and an 8-pin PDIP package. The device provides a 2 mV maximum input offset-voltage specification, 1.3 microseconds propagation delay, and an operating temperature range of -40°C to 85°C. A comparator is a signal-conditioning semiconductor that evaluates two input voltages and produces a logic-level result indicating which input is higher. A dual differential comparator combines two independent comparison channels in one package. The LM2903 belongs to the broader comparator and amplifier IC hierarchy and is designed for single-supply operation, split-supply operation, and interfaces where an open-collector output can directly drive pull-up resistors. The principal features include low offset voltage, low power consumption, and open-collector outputs. Open-collector outputs can sink current while remaining in a high-impedance state when inactive, allowing the output transition speed and logic level to be set by an external pull-up network. The two channels operate independently, supporting simultaneous comparison, level detection, window monitoring, or dual-threshold functions in one circuit. The Texas Instruments LM2903-N family is specified for operation from a single supply across a wide voltage range, with an operating range extending to 36 V. The 2 mV maximum offset specification is useful when the comparator must resolve small voltage differences. Its 1.3 microsecond response is suitable for general-purpose industrial control, monitoring, and interface circuits rather than ultra-high-speed signal comparison. Typical applications include industrial sensor interfaces, overvoltage and undervoltage detection, battery threshold monitoring, temperature-control loops, and general digital logic interfaces. The open-drain architecture also allows wired logic, alarm aggregation, and level-shifting arrangements when suitable pull-up resistors are provided. For reliable PCB implementation, place the input and output components close to the device and provide a defined pull-up resistor on each open-collector output. Check the output sink-current limit, input common-mode range, supply decoupling, and unused-channel configuration against the manufacturer datasheet before finalizing the design. This product page combines the exact orderable part information, package information, comparator characteristics, drop-in candidate analysis, and application-focused engineering guidance to support faster component selection and board-level implementation.
LM2903NG - Dual Low-Offset Voltage Comparator | onsemi | PDIP-8
The onsemi LM2903NG is a dual independent precision voltage comparator with low input offset voltage, open-collector outputs, and single or split supply operation from 2V to 36V, housed in an 8-pin PDIP through-hole package. The device operates over -40C to +105C and supports input common-mode voltage ranges down to ground. A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC and signal-conditioning hierarchy of power management and analog semiconductor systems. Unlike an operational amplifier, a comparator is intentionally optimized for fast, saturated switching between two output states rather than linear amplification, and the LM2903 family adds an open-collector output stage that lets multiple devices share a common pull-up node for wired-OR logic. Key features include a supply range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), input common-mode range that extends to the negative rail, and very low input bias current of about 250nA. The typical response time is approximately 1.5 microseconds, which suits general-purpose threshold detection, level shifting, and oscillator timing rather than high-speed clocking. The LM2903 architecture uses two fully independent comparator channels sharing one die and supply pins. Each channel has its own inverting and non-inverting inputs plus an open-collector output, so external pull-up resistors define the output high level, allowing interface to logic families at any voltage up to the supply rails. Typical applications include power-supply undervoltage and overvoltage supervision, battery threshold monitoring, window comparators, relaxation oscillators, and sensor threshold detection in industrial and automotive-adjacent environments. The wide supply range makes it a natural fit for 5V, 12V, and 24V industrial rails. For design, always include a pull-up resistor on each open-collector output (typically 1k to 10k ohm), and add hysteresis with positive feedback when comparing slowly moving signals to avoid output chatter near the threshold. This page synthesizes datasheet parameters, drop-in alternatives, practical design notes, and application guidance not found together in the manufacturer datasheet.
LM2903P - Dual Differential Comparator, 30 V, PDIP-8 | Texas Instruments
The Texas Instruments LM2903P is a dual differential comparator with open-collector, rail-to-rail outputs, supplied in an 8-pin PDIP package. The device contains two independent voltage comparators designed for general-purpose signal conditioning, threshold detection, and simple control applications. The verified distributor and manufacturer data identifies the LM2903 as a dual differential comparator intended for operation from a single supply or dual supplies, with a maximum supply voltage rating of up to 38 V for the B-version family and a listed operating supply range of 2 V minimum for comparison devices in the same family. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic result. The LM2903 family belongs to the broader comparator and analog signal-conditioning hierarchy, where open-collector outputs provide flexible interface options for pull-up resistors, relay drivers, lamp circuits, and low-voltage digital logic. Its differential inputs allow one signal to be monitored against a reference or another input, making the device suitable for window detection, current sensing, sensor thresholding, and industrial control circuits. The LM2903P uses two independent comparators, with output transistors capable of sinking current into an external pull-up network. The verified data identifies the output style as open-collector and rail-to-rail, while the family description confirms two independent voltage comparators and operation from a single power supply over a wide voltage range. The LM2903P is supplied through a tube package in the verified distributor result, making it appropriate for through-hole production and prototype boards rather than compact surface-mount assemblies. Typical uses include monitoring a control voltage, detecting an overvoltage or undervoltage condition, converting an analog sensor threshold into a logic event, and driving an alert or shutdown input. Because an open-collector output requires an external pull-up resistor, the output voltage is defined by the pull-up supply and resistor rather than by the comparator alone. Designers should also verify input common-mode limits, output sink current, supply-current requirements, and propagation delay for the exact operating conditions. The principal design consideration is that the LM2903P is a through-hole PDIP-8 comparator, not a low-power modern micropower comparator. Its application circuit must respect the device's supply voltage, input voltage, common-mode range, output pull-up arrangement, and maximum output current. This page combines the verified manufacturer and distributor information with practical application guidance and same-family replacement context for engineers evaluating an LM2903P design.
LM2903P-MAND - Dual Open-Collector Comparator | Texas Instruments
The Texas Instruments LM2903P-MAND is a dual differential comparator with two independent comparator channels and open-collector outputs, packaged in an 8-pin PDIP package. The device compares two input voltages at each channel and provides a logic-level indication of their relative relationship. Its through-hole PDIP package supports straightforward PCB assembly, prototyping, repair, and applications that favor accessible leads over a surface-mount footprint. A comparator is an analog signal-conditioning IC that occupies the comparator hierarchy within analog signal processing and broader semiconductor systems. Unlike an operational amplifier, a comparator is optimized for fast logic-level decisions and normally has open-collector outputs suited to pulling a wired bus or logic node high. The LM2903P-MAND contains two such channels, allowing a single component to monitor two thresholds, supervise two signals, or implement a window-style decision function. The principal features of the LM2903P-MAND are its dual-channel architecture, differential inputs, open-collector outputs, and PDIP-8 package. Each channel can use its non-inverting and inverting inputs around a common reference. The open-collector outputs require an external pull-up resistor when the output must actively drive a high voltage level. This arrangement also permits several open-collector outputs to share a bus when their operating conditions and logic polarity are compatible. The LM2903P-MAND belongs to the Texas Instruments LM2903 dual-comparator family. Its architecture supports operation from a single supply or split supplies, depending on the selected voltage limits and application requirements. Differential comparison is useful when the two inputs are referenced to the same signal source, such as a sensor divided into two scaled voltages. Open-collector outputs are particularly useful for relay, lamp, alarm, and industrial logic interfaces because they provide a straightforward way to sink current. Typical applications include industrial sensor threshold detection, overvoltage and undervoltage supervision, automotive electronics, battery monitoring, control-panel annunciation, and general-purpose digital control systems. The PDIP package is especially useful in equipment where long-term maintainability, socketed assembly, or hand rework is valuable. Designers should still account for the open-collector pull-up network and verify the common-mode, supply, and output-current limits against the manufacturer datasheet for the exact ordering code. For a new PCB, route the input traces away from switching nodes and connect a suitable pull-up resistor to each open-collector output. Confirm the input reference arrangement so the required high or low output polarity is obtained without reversing the channel logic. Because the MAND ordering suffix may denote a special qualification or temperature treatment, do not infer its production limits solely from the base LM2903 family designation; consult the exact MPN documentation. This product page organizes the dual-comparator function, verified package information, practical design notes, and same-footprint alternatives into an engineer-focused guide. It also highlights the distinction between the LM2903 family and the B-version with improved electrical specifications, helping PCB designers separate drop-in continuity from a functional upgrade.
LM2903PS-MAND - Dual Open-Collector Comparator | Texas Instruments
The Texas Instruments LM2903PS-MAND is a dual differential comparator with two independent comparator channels, an open-collector output architecture, and an 8-pin small-outline package. The LM2903 family is designed for general-purpose signal comparison and can operate from a single supply while also supporting split-supply arrangements. Its input common-mode range includes ground, making it useful in battery-powered and mixed-polarity systems where inputs may approach the lower supply rail. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. Within the semiconductor hierarchy, a comparator belongs to the broader operational-amplifier and signal-conditioning family, with the LM2903 providing two independently usable channels in one monolithic package. This integration reduces the component count and package footprint in threshold detection, sensing, and control circuits. The primary features of the LM2903PS-MAND are its dual-channel configuration, open-collector outputs, ground-referenced input capability, and ability to operate from either a single or split supply. Open-collector outputs are useful when the output must pull up to a system-specific voltage, interface with TTL or CMOS logic, or support wired-AND behavior. Each channel may also be used independently, allowing one device to compare two different signal pairs. In practical signal-path terms, the comparator evaluates a voltage present at its inverting or non-inverting input against a reference or threshold established by the other input. Its wide common-mode capability allows direct sensing of low-level signals referenced to ground. Designers should account for input and output timing, pull-up requirements, supply behavior, and the transition characteristics listed in the manufacturer datasheet when setting switching thresholds or driving downstream circuitry. Typical applications include battery threshold monitoring, sensor signal conditioning, window comparators, overvoltage detection, industrial control interfaces, and general-purpose digital decision logic. The two channels are particularly useful when a design needs two related comparisons, such as monitoring both a rising threshold and a falling threshold, or detecting upper and lower limits around a nominal operating point. For implementation, connect an appropriate pull-up resistor to each open-collector output and account for the resulting rise time when operating speed matters. Keep input and output routing compact to reduce sensitivity to interference, and confirm the device's operating-temperature, supply-voltage, and input-voltage limits against the requirements of the target application before releasing the PCB design. This product overview combines the device's core functionality with practical guidance on open-collector interfaces, dual-channel usage, threshold detection, and drop-in alternatives. It also provides comparison-focused engineering information intended to make component selection and PCB reuse faster than a distributor specification summary alone.