بەرهەمەکان (3,200+)

LM2903PSRG4 - Dual Differential Comparator | Texas Instruments
LM2903PSRG4

LM2903PSRG4 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903PSRG4 is a dual differential comparator containing two independent comparator channels, with a 36 V maximum supply range, 0.4 mA typical supply-current drain per comparator, and an 8-pin SOIC package. It is designed for single-supply operation or dual-supply operation when the total supply span remains within 2 V to 36 V. A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals. The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain. The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits. Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable. When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter. This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.

RFQ پەیوەندی
LM2903PT - Dual Low-Power Voltage Comparator, +2V to +36V | STMicroelectronics
LM2903PT

LM2903PT - Dual Low-Power Voltage Comparator, +2V to +36V | STMicroelectronics

The STMicroelectronics LM2903PT is a low-power dual voltage comparator with two independent, single-pole comparators on a single monolithic substrate, supplied in an 8-pin TSSOP (8TSSOP) surface-mount package. It operates from a single +2 V to +36 V supply or from dual supplies of +/-1 V to +/-18 V, drawing only 0.4 mA of supply current independent of supply voltage, equal to 1 mW per comparator at +5 V. A voltage comparator is an amplifier IC that compares two input voltages and switches its output when the difference between them changes sign. In system terms a comparator sits at the base of the hierarchy of analog signal conditioning: comparator -> amplifier IC -> analog integrated circuit -> semiconductor, and it is the natural front end for threshold detection, sensor signalling and window monitoring. Because the LM2903 output is an open-collector style transistor stage, it interfaces directly with TTL, MOS and CMOS logic families and can pull a rail low without an external push-pull driver. Key features of the LM2903PT include a common-mode input voltage range that includes ground even when operated from a single supply, very low supply current drain of 0.4 mA, low input bias current of 25 nA typical, and low input offset current of +/-5 nA typical. The low offset current means the two comparators of the pair track each other closely, which matters when one channel is used as a reference and the other as the active comparator in a window-detector arrangement. The device is built on a bipolar monolithic process, which explains the wide supply range and the ability to accept input signals near and beyond ground. Two comparators share one package, so a single 8-pin TSSOP footprint can implement a full two-threshold window comparator, a dual-level battery monitor, or a pair of independent limit detectors for analog signals with only one board space increment. Typical applications include industrial control and instrumentation thresholds, battery-powered monitoring and protection circuits, motor and solenoid drive control loops, sensor interface modules, and consumer equipment power supervision. Because supply current is independent of the supply voltage, the part remains usable across wide battery-discharge ranges without the quiescent current rising as the cell voltage falls. When laying out the design, route the two input nets as short and separated as possible, keep the open-collector output pull-up resistor close to the device, and confirm that the logic family connected to the output can tolerate the pull-up voltage. Use the pin-description table in the STMicroelectronics datasheet when assigning PCB tracks. This page brings together the supply-voltage and input-current characteristics, drop-in alternatives that share the identical TSSOP-8 footprint, comparison tables and practical design notes that go beyond a bare parameter listing, helping engineers qualify the part quickly for industrial, automotive-adjacent and consumer designs.

RFQ پەیوەندی
LM2903PW - Dual Differential Comparator, 36V TSSOP-8 | TI
LM2903PW

LM2903PW - Dual Differential Comparator, 36V TSSOP-8 | TI

The Texas Instruments LM2903PW is a dual differential comparator with open-collector outputs, rated for supply operation up to 36 V, drawing a typical 0.4 mA of supply current per comparator, and housed in an 8-pin TSSOP package. It belongs to the industry-standard LM193/LM293/LM393/LM2903 comparator family trusted in automotive, industrial, and consumer designs. A comparator (also called a voltage comparator) is an analog building block that compares two input voltages and drives its output to indicate which is higher. It sits within the broader hierarchy of amplifier ICs and analog signal-chain components, bridging the gap between raw sensor signals and digital logic decisions. Unlike an operational amplifier used in closed-loop gain configurations, a comparator operates open-loop with very high gain, switching its output rail-to-rail between defined logic states. Key features of the LM2903PW include single-supply or dual-supply operation across a wide 36 V range, low supply-current drain that is largely independent of supply voltage, low input bias current of 25 nA typical per comparator, and low input offset current of 3 nA typical. The open-collector outputs allow wired-OR connections and direct interface with TTL, CMOS, and other logic families via a pull-up resistor. Architecturally, each comparator provides high differential gain with inputs that work down to the negative supply rail (ground in single-supply systems), enabling ground-referenced sensing. The common-mode input range extends to the positive supply minus about 1.5 V. A typical response time of approximately 1300 ns suits monitoring, threshold detection, and level-shifting tasks where microsecond-scale decisions are adequate. Typical applications include automotive sensor threshold detection, battery undervoltage lockout, zero-crossing detection for motor control, window comparators in industrial monitoring, and oscillator/timer circuits. The automotive temperature grade (up to +125 C ambient) makes the LM2903 family a default choice in vehicle environments. Design consideration: because outputs are open-collector, every output requires a pull-up resistor to the desired logic rail; choosing a lower pull-up resistance speeds rise time but increases power dissipation. This page adds engineering value beyond the datasheet: a parameter comparison against drop-in alternatives, practical design notes on pull-up sizing and hysteresis, application guidance, and sourcing FAQs consolidated in one place.

RFQ پەیوەندی
LM2903PWR - Dual Open-Collector Comparator | Texas Instruments
LM2903PWR

LM2903PWR - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903PWR is a dual differential comparator with an open-collector output, rail-to-rail input capability, and a wide operating range of ±18V, or 36V total, in an 8-pin TSSOP package. The device contains two independent comparators, making it suitable for threshold detection, window comparison, industrial control, and signal-conditioning systems. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. In the larger semiconductor hierarchy, the LM2903 belongs to the comparator and analog IC family, where its differential inputs, open-collector outputs, and wide supply tolerance support robust sensing across industrial voltage ranges. The LM2903PWR provides two independent comparison channels in one package. Its open-collector outputs can sink output current while remaining in a high-impedance state when inactive, allowing pull-up resistors to set the logic-high voltage and multiple comparator outputs to share a bus when wired appropriately. Rail-to-rail input operation extends the usable common-mode range toward the supply limits, which is valuable in battery-powered and industrial designs. The improved LM2903B family associated with this device is specified for operation up to 38V, an ESD rating of 2kV HBM, input offset voltage as low as 0.37mV, input bias current as low as 3.5nA, supply current of 200µA per comparator, and response time of 1µs. These characteristics improve on older LM393-family performance while retaining the established LM2903 function and pin arrangement. Typical uses include DC threshold monitors, overvoltage and undervoltage detection, sensor conditioning, window comparators, and industrial control logic. In a typical application, each comparator evaluates a signal against a reference generated by a resistor divider, while external pull-up resistors convert the open-collector output into a valid logic-high state. Layout should keep input traces short, route sensitive comparison nodes away from switching-node currents, and place input and reference-network components close to the device. A common ground reference and stable bypass capacitance are essential because comparator decisions depend on the difference between two input voltages. This page combines manufacturer device information, verified distributor listings, package identification, replacement analysis, and application-focused design guidance. It also distinguishes confirmed drop-in options from alternatives that cannot be installed on the same 8-pin TSSOP footprint without redesign.

RFQ پەیوەندی
LM2903PWRG3 - Dual Differential Comparator | Texas Instruments
LM2903PWRG3

LM2903PWRG3 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903PWRG3 is a dual differential comparator containing two independent general-purpose comparator channels, a 2 V to 36 V single-supply operating range, and open-collector outputs in an 8-pin TSSOP package. According to the Texas Instruments LM2903 product information, each channel compares two differential inputs and can also operate from split power supplies spanning 2 V to 36 V. A differential comparator is an analog integrated circuit that evaluates the relative voltage between its inverting and non-inverting inputs. When the non-inverting input rises above the inverting input, the associated output transistor turns on; when the relationship reverses, the output transistor turns off. This complementary sensing function places the LM2903 in the amplifier and interface IC hierarchy, where comparator ICs convert small analog voltage differences into logic-level decisions for control, protection, and signaling systems. The LM2903 provides two independent channels in one package, reducing component count in designs requiring more than one threshold comparison. Its open-collector outputs permit wired connections and external pull-up resistors, providing flexibility for interfacing with TTL, CMOS, and other digital logic families. The 2 V to 36 V supply range supports both low-voltage control circuits and higher-voltage industrial systems, while the differential input arrangement helps monitor two sensed voltages without requiring a separate input amplifier. The PWRG3 ordering configuration is supplied in an 8-TSSOP surface-mount package for compact PCB layouts and automated assembly. Open-collector outputs require suitable pull-up arrangements when a logic-high output state is needed. Because both comparators share the same supply package while retaining independent inputs and outputs, designers can allocate the two channels to separate analog domains when those domains remain compatible with the device's common-mode and supply limitations. Typical uses include overvoltage and undervoltage detection, window monitoring, sensor threshold comparison, industrial control logic, and power-supply supervision. The two-channel organization is particularly useful in window comparators, where one channel establishes an upper threshold and the other establishes a lower threshold, or in systems where separate alert functions require independent decisions. When designing a PCB around the LM2903PWRG3, place input, output, and bypass connections to minimize noise coupling into the high-impedance comparison inputs. Select pull-up resistors according to the required sink current, rise time, and logic family. Verify common-mode range, supply polarity, and output-state requirements across temperature and supply tolerance before treating the comparator output as a guaranteed logic-high signal. This product page combines the Texas Instruments device information with package, application, sourcing, and replacement guidance. It also provides design-focused comparisons that help engineers distinguish ordering-grade, package, supply, and output-stage differences before selecting a pin-compatible replacement or integrating the device into a new analog control board.

RFQ پەیوەندی
LM2903Q2T - Dual Low-Power Voltage Comparator | STMicroelectronics
LM2903Q2T

LM2903Q2T - Dual Low-Power Voltage Comparator | STMicroelectronics

STMicroelectronics LM2903Q2T is a dual, independent, low-power voltage comparator designed for single-supply or split-supply operation across a wide voltage range. The device is identified as a standard general-purpose comparator with open-collector, rail-to-rail outputs and is packaged in an 8-DFN 2 x 2 mm package. Its two comparator channels can be used separately or together for threshold detection, overvoltage and undervoltage monitoring, signal conditioning, and basic analog control functions. A voltage comparator is an analog mixed-signal IC that compares an input voltage with a reference voltage and changes its output state when the relationship between those voltages changes. The LM2903 belongs to the comparator hierarchy, which sits between general-purpose analog signal conditioning and system-level protection or control. Its open-collector outputs can be pulled up to a suitable supply rail, allowing interface compatibility with TTL, CMOS, MOS, and other digital logic when the output circuit is designed correctly. The LM2903Q2T is specifically suited to low-power applications because the manufacturer identifies it as a low-power dual comparator. Its two independent channels provide flexibility in battery-operated equipment, industrial sensing, automotive electronics, consumer products, and embedded control systems. The 2 x 2 mm DFN package also supports compact layouts where board area is limited, although its exposed thermal pad and fine-pitch assembly requirements require careful PCB design. The comparator output architecture is open collector, so an external pull-up resistor is generally required to establish a high output level. The output transistor can sink current when the comparator condition is met, while the pull-up network determines the high-state voltage and rise time. This configuration is useful for wired-AND signal aggregation, but it also means that the output voltage, transition timing, and allowable sink current depend on the external resistor and load. The LM2903 family is designed for operation from a single supply or split supplies, making it appropriate for systems that require comparison of signals referenced to ground or signals that exceed ground when both positive and negative rails are available. Because the exact electrical limits, common-mode range, output timing, and automotive qualification details are not shown in the retrieved product summaries, final circuit design should use the manufacturer datasheet and its recommended operating conditions. A compact application should include local input filtering when sensor leads are long or noisy, a defined output pull-up, and adequate copper around the exposed pad when both channels operate continuously. The small DFN package can reduce board space, but its compact size does not eliminate thermal or assembly constraints. Use the manufacturer pin configuration and land pattern when assigning inputs, outputs, supply pins, and the exposed pad. This page combines the LM2903Q2T product identity, verified manufacturer and distributor references, application guidance, package considerations, and design notes. It also explains why open-collector operation, power-supply topology, output pull-up design, and thermal layout determine whether the comparator works reliably in a real system.

RFQ پەیوەندی
LM2903QDG4 - Dual Differential Comparator, 36 V | Texas Instruments
LM2903QDG4

LM2903QDG4 - Dual Differential Comparator, 36 V | Texas Instruments

The Texas Instruments LM2903QDG4 is a dual differential comparator containing two independent comparison channels, operating from a single 2 V to 36 V supply or dual supplies whose total voltage spans 2 V to 36 V. The device accepts differential input voltage and uses open-collector outputs compatible with TTL, CMOS, and MOS logic. It is packaged for surface-mount assembly in an 8-pin SOIC package. A differential comparator is an analog interface integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits, where it bridges low-level sensor or signal voltages to a digital logic domain. Each half of the device can operate independently, allowing two comparisons in one package when the power supplies and input signals share a suitable common range. The principal features are dual independent comparators, a wide 2 V to 36 V operating range, open-collector outputs, and logic compatibility with TTL, CMOS, and MOS devices. The open-collector architecture gives the output a defined pulled-up state when the output transistor is off and allows multiple open-collector outputs to share a wired bus when suitable, provided each output has its own pull-up path. The operating-temperature grade extends from -40 °C to 125 °C for industrial temperature conditions. Each comparator uses a differential input stage and an open-collector output stage. A positive differential input produces the corresponding output state, while the magnitude and polarity of the differential input determine switching behavior. Because the outputs are open collector, external pull-up resistors are required for normal TTL or CMOS-compatible operation. The pull-up value controls rise time, power consumption, and susceptibility to bus capacitance, so it must be selected with the driven load and operating speed in mind. Typical uses include monitoring a sensor threshold, detecting overvoltage or undervoltage conditions, comparing an analog measurement with a reference, and providing an open-collector signal to a microcontroller or logic gate. The wide supply range is useful for industrial control systems, automotive-adjacent sensing circuits, power-supply monitoring, and test equipment where input signals may exceed conventional low-voltage logic rails. PCB layout should keep the exposed routes short and provide a stable ground reference close to the comparator. Place input and output components according to the manufacturer application guidance, and avoid routing high-current or switching-node copper directly beside the differential inputs. Pull-up resistors should connect to the intended logic supply rather than the comparator supply when separate output-interface voltage is required. This page combines the manufacturer's device information, package details, operating limits, direct drop-in candidates, comparison parameters, and practical implementation guidance. It also identifies which electrical details require confirmation in the LM2903 family datasheet before production release.

RFQ پەیوەندی
LM2903QDGKRQ1 - Dual 36V Automotive Comparator | Texas Instruments
LM2903QDGKRQ1

LM2903QDGKRQ1 - Dual 36V Automotive Comparator | Texas Instruments

The Texas Instruments LM2903QDGKRQ1 is an AEC-Q100 Grade 0 and Grade 1 automotive dual differential comparator with open-collector outputs, operating from 3 V to 36 V and supplied in an 8-pin VSSOP package. The device provides two independent comparison channels, a common supply range of 3 V to 36 V, and input common-mode operation extending to the supply rails. According to the TI LM2903-Q1 product page, the LM2903-Q1 family is designed for cost-sensitive automotive and industrial systems requiring high-voltage tolerant inputs and open-collector outputs. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital output indicating whether the non-inverting input is above or below the inverting input. Within the broader hierarchy, the LM2903-Q1 is a differential comparator, a general-purpose analog IC, and a member of the power-management and signal-conditioning semiconductor category. Its open-collector output structure allows several comparator outputs to be wired together for wired-AND operation and requires an external pull-up resistor for normal logic-level operation. Key characteristics include dual-channel operation, a 36 V maximum supply capability, and open-collector outputs suitable for automotive battery-powered systems. The AEC-Q100 Grade 0 and Grade 1 qualification supports demanding automotive environments, while the wide input voltage range reduces the need for separate input protection in many 12 V, 24 V, and 36 V system architectures. The 8-pin VSSOP package also supports compact PCB layouts where space is limited. The LM2903-Q1 architecture is designed for general-purpose threshold detection rather than high-speed waveform discrimination. Its differential input stage allows sensing of small analog changes, and the open-collector outputs can directly pull up a logic bus, drive a relay driver, or interface with automotive transceiver inputs. The open-collector configuration also provides wired-AND behavior when multiple comparator channels share a pull-up resistor. Typical applications include automotive battery monitoring, overvoltage and undervoltage detection, window or door sensing, sensor conditioning, and industrial control systems. In battery systems, the wide supply tolerance supports operation across load dump and automotive electrical-environment conditions when paired with appropriate protection. In control logic, two independent channels can monitor separate thresholds or implement a window comparator using external resistor networks. When designing the PCB, route the comparator inputs away from switching nodes and high-current return paths because input offset voltage can make nearby interference appear as a false state transition. Place the pull-up resistor close to the open-collector output and verify that its value keeps the logic rise time within the receiving device's limits. Automotive designs should also include the transient-protection components required by the complete vehicle electrical system rather than relying on the comparator alone for surge suppression. This page consolidates the verified package, voltage, output, qualification, and lifecycle information with application guidance, comparison parameters, and design notes that support faster component selection and PCB implementation.

RFQ پەیوەندی
LM2903QDRG4 - 36 V Dual Comparator | Texas Instruments
LM2903QDRG4

LM2903QDRG4 - 36 V Dual Comparator | Texas Instruments

The Texas Instruments LM2903QDRG4 is a dual differential analog comparator with two independent comparison channels, an open-collector output, and an 8-pin SOIC package. The device supports single-supply or dual-supply operation over a wide voltage range up to 36 V, while each comparator typically consumes 0.4 mA. It is specified for an ambient temperature range of -40°C to +125°C. An analog comparator is an integrated circuit that compares two input voltages and produces a digital-level result indicating which input is higher. The LM2903 belongs to the comparator hierarchy within amplifier and interface ICs, providing a simple alternative to a general-purpose operational amplifier used only for voltage comparison. Its open-collector outputs can sink external pull-up current and support wired logic, level translation, or open-drain bus arrangements. The two comparators operate independently, allowing one package to implement two sensing or threshold functions. Low typical input bias current of 25 nA helps minimize disturbance on high-impedance sensor circuits. The low supply-current drain, reported as 0.4 mA typical per comparator, is useful in battery-powered equipment where continuous comparator consumption affects available operating time. The LM2903 can operate from a single positive supply or from two supplies when their voltage difference is between 2 V and 36 V. In dual-supply use, the positive supply must remain at least 1.5 V above the negative supply referenced by the device. This flexibility supports comparator designs around 5 V, 12 V, 24 V, and split-rail industrial systems. Typical applications include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage supervision, window comparators for analog signals, and open-drain alarm signaling. Because each output is open collector, a pull-up resistor is required when the output must drive a conventional logic-high state. The open-collector architecture also permits several comparators to share a common pull-up when wired logic is appropriate. PCB design should keep input and output traces short, provide a solid ground return, and place input filtering close to the relevant pins. Because an open-collector output cannot source current, size the pull-up resistor to balance rising time, signal current, and power dissipation. The -40°C to +125°C rating supports industrial temperature ranges, although the complete system still requires suitable thermal verification. This product page combines the exact LM2903QDRG4 ordering information with package, pinout, sourcing, comparison, and application guidance. It helps engineers distinguish verified pin-compatible options from devices that merely use a similar 8-pin package but differ in electrical behavior, qualification, or supply requirements.

RFQ پەیوەندی
LM2903QDRG4Q1 - Dual Comparator | Texas Instruments
LM2903QDRG4Q1

LM2903QDRG4Q1 - Dual Comparator | Texas Instruments

Texas Instruments LM2903QDRG4Q1 is an automotive dual differential comparator containing two independent comparator channels, with an 8-SOIC package, a 2 V to 36 V supply-voltage range, open-collector outputs, and an operating-temperature range of -40°C to +125°C. The device supports single-supply operation and dual-supply operation when the supply difference and common-mode requirements are satisfied. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category belongs to the broader amplifier IC and signal-conditioning hierarchy, where open-collector outputs are useful for wired logic, system-level signaling, and driving external pull-up networks. The LM2903-Q1 family combines independent channels with automotive qualification for applications requiring reliable operation across extended temperatures. Key electrical characteristics include a maximum input-offset voltage of 7 mV at 5 V, a maximum input-bias current of 0.25 µA, typical output current of 20 mA, and maximum quiescent current of 2.5 mA. Its differential architecture supports sensing whether one voltage is above or below another without requiring a feedback network. The open-collector output can sink current while remaining in a high-impedance state when the output transistor is off. The two channels operate independently, allowing one device to implement two threshold decisions, window-detection functions, or complementary monitoring functions. A supply range extending to 36 V is valuable in automotive and industrial systems where the comparator may be connected to protected battery-derived or higher-voltage signal rails. The low input-bias current helps reduce errors when sensing high-impedance sources, while the specified offset limit establishes the basic threshold-accuracy boundary. Typical applications include automotive battery and power-rail supervision, sensor threshold detection, overvoltage and undervoltage indication, window comparators, and digital-control interfaces. The open-collector architecture also allows multiple comparators to share a pull-up resistor when wired logic is acceptable. External pull-up selection must account for the required sink current, rise time, bus capacitance, and system-level fault conditions. Designers should account for input common-mode limits, supply polarity, output pull-up placement, and unused-channel handling. Place the pull-up resistor near the open-collector output or system bus, and verify that the 20 mA typical output-current capability covers the worst-case sink demand. The manufacturer datasheet and pin-description table remain the controlling references for connection, common-mode range, and package details. This product page combines manufacturer specifications, package information, drop-in replacement guidance, and practical application guidance. It supports faster component selection while preserving the electrical checks required for reliable comparator-based sensing and control systems.

RFQ پەیوەندی
LM2903QDRQ1 - 36V Automotive Dual Comparator | Texas Instruments
LM2903QDRQ1

LM2903QDRQ1 - 36V Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903QDRQ1 is an AEC-Q100-qualified automotive dual differential comparator with two independent comparison channels, a 2 V to 36 V single-supply operating range, and open-collector outputs in an 8-pin SOIC package. It is designed for high-voltage industrial and automotive systems where two independent comparator channels are required in a compact package. A differential comparator is an analog integrated circuit that compares the voltage at its inverting input with the voltage at its non-inverting input and changes its output state when the input difference crosses a defined threshold. The comparator belongs to the broader hierarchy of analog ICs, signal-conditioning ICs, and semiconductor devices. Its open-collector architecture allows the output to be pulled up to a system-compatible logic voltage rather than being limited to the IC supply rail. Key electrical characteristics include a typical input offset voltage of 2 mV, a typical input bias current of 25 nA, and a supply current of 0.4 mA per comparator. Each channel provides one push-pull-compatible input stage and an open-collector output that is compatible with TTL, MOS, and CMOS logic families. The single-supply operating range is 2 V to 36 V, while operation from dual supplies is possible when the total supply difference is between 2 V and 36 V. The LM2903-Q1 family combines a wide supply range with low supply current and AEC-Q100 Grade 0 and Grade 1 options. These characteristics make it suitable for sensing circuits connected to higher-voltage buses than those commonly handled by low-voltage mixed-signal comparators. The open-collector outputs also simplify wired-interface and level-shifting arrangements when an external pull-up resistor is used. Typical applications include automotive battery and power-system monitoring, industrial control systems, motor and solenoid feedback circuits, window or lighting controllers, overcurrent and overvoltage detection, and general-purpose threshold sensing. Two channels in one package reduce board area when independent comparison functions are required. The main design consideration is the open-collector output. Every output requires a pull-up resistor to the desired logic rail, and the pull-up must be sized against the output sink current and expected switching rate. Designers should also verify the input common-mode range at the selected supply voltage before committing the circuit to automotive or industrial rail conditions.

RFQ پەیوەندی
LM2903QM8-13 - Dual 36V Comparator | Diodes Inc.
LM2903QM8-13

LM2903QM8-13 - Dual 36V Comparator | Diodes Inc.

The Diodes Incorporated LM2903QM8-13 is a dual differential voltage comparator designed for automotive and industrial systems, with two independent comparator channels, a 36 V maximum supply rating, 2 mV input offset voltage, 25 nA input bias current, and an 8-MSOP package. It supports input common-mode ranges that include ground and a differential input range equal to the supply voltage. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output when the difference crosses a defined threshold. The LM2903 belongs to the broader comparator hierarchy within analog ICs and signal-conditioning electronics. Each of its two channels includes a noninverting input, an inverting input, and an output, allowing one device to perform threshold detection, window comparison, or independent level sensing. Key features include low input offset voltage, low input bias current, 5 nA output leakage current, and low output saturation voltage of 200 mV at 4 mA. The LM2903QM8-13 is identified as an automotive-compliant Q-grade device, while its lead-free construction and full RoHS compliance support environmentally constrained production programs. Its open-collector-style output is compatible with TTL, MOS, and CMOS logic systems. Technically, the device combines precision differential input handling with practical supply-voltage tolerance. The comparators can operate across a broad input range because the common-mode input voltage includes ground while the differential input range can extend to the power-supply voltage. This makes the device useful where sensing signals may approach 0 V or where input stages share the comparator supply rail. Designers should still verify absolute maximum conditions and output pull-up arrangements for the specific operating environment. Typical uses include automotive battery and rail monitoring, sensor threshold detection, window comparators, overvoltage and undervoltage detection, industrial control thresholds, and digital-interface signaling. The dual-channel organization saves board area when two independent decisions are required, while the 8-MSOP package supports compact surface-mount assemblies. For implementation, use a suitable pull-up resistor on each open-collector output and account for output-leakage effects when the output is high. Keep sensitive input traces short, provide a stable local supply connection, and verify common-mode, differential, and absolute-maximum limits before applying large transient voltages. This page combines the manufacturer specifications, automotive qualification details, package information, drop-in alternatives, and practical circuit guidance into a design-oriented reference for engineers evaluating the LM2903QM8-13.

RFQ پەیوەندی
LM2903QPWRG4Q1 - Dual 36V Automotive Comparator | TI
LM2903QPWRG4Q1

LM2903QPWRG4Q1 - Dual 36V Automotive Comparator | TI

The Texas Instruments LM2903QPWRG4Q1 is an AEC-Q100 Grade 0 and Grade 1 automotive dual differential comparator with an open-collector output configuration, housed in an 8-pin TSSOP package. The device operates from 2 V to 36 V on a single supply or from plus or minus 18 V on dual supplies, making it suitable for high-voltage industrial and automotive signal-conditioning systems. A differential comparator compares two input voltages and changes its output state according to the polarity of the difference between them. The LM2903-Q1 family contains two independent comparators, allowing one package to implement two threshold decisions, window monitoring functions, or independent protection channels. Its wide input and supply voltage ranges support battery-derived systems, industrial control boards, and 24 V vehicle electrical environments. The automotive-qualified LM2903QPWRG4Q1 provides low offset voltage, low supply current, low input bias current, 1.3 microsecond propagation delay, and improved 2 kV ESD performance. Its open-collector outputs allow wired-AND operation with an external pull-up resistor and permit the output voltage to be referenced independently of the internal supply. This makes the device practical for interfacing with logic gates, relay drivers, and systems requiring fail-safe output states. The LM2903-Q1 family is designed for drop-in convenience with established LM2903-family footprints, helping reduce redesign effort when automotive qualification and a 36 V maximum supply are required. The 8-pin TSSOP package supports compact surface-mount layouts, while the -40 C to +125 C operating range supports harsh industrial and vehicle environments. Typical uses include automotive battery monitoring, overvoltage and undervoltage detection, fan-speed control, sensor conditioning, power-supply supervision, and industrial control systems. The dual architecture also allows both halves to operate independently, although their input common-mode behavior and output pull-up network must be checked against the system requirements. When laying out the board, keep comparator inputs away from switching nodes and route the ground reference directly to the device ground pin. Choose the external output pull-up for the required logic family, account for the open-collector sink-current limit, and validate the design across the full temperature range. This page combines manufacturer specifications, package details, verified listing information, drop-in alternatives, and practical design guidance for faster component selection.

RFQ پەیوەندی
LM2903QPWRQ1 - 36V Automotive Dual Comparator | Texas Instruments
LM2903QPWRQ1

LM2903QPWRQ1 - 36V Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903QPWRQ1 is an AEC-Q100 Grade 0 and Grade 1 automotive dual differential comparator with an open-collector, rail-to-rail output configuration, supplied in an 8-pin TSSOP (PW) package. It operates from a single or dual supply across a wide range of supply voltages up to 36 V, consumes 0.4 mA typical per comparator, and is specified for temperatures from -40°C to 125°C. A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level indication of their relationship. The LM2903-Q1 family belongs to the broader differential comparator and analog signal-conditioning hierarchy, where it sits between general-purpose analog front ends and downstream control logic such as system supervisors, motor controllers, and automotive ECUs. Its differential inputs allow small voltage differences to be resolved without converting the signal through an analog-to-digital converter. Key features include a 36 V maximum supply capability, low supply-current drain independent of supply voltage, 25 nA typical input bias current, and 3 nA typical input offset current. The open-collector outputs can sink current for wired-AND logic or drive external pull-up devices, while the dual differential architecture places two independent comparator channels in one package. Automotive Grade 0 and Grade 1 qualification supports use in demanding environmental conditions. The device supports single-supply or dual-supply operation and is designed for low-power threshold detection. Its wide supply range makes it suitable for systems that must monitor voltages well above conventional 5 V or 12 V rails, including vehicle battery systems and industrial control boards. The rail-to-rail open-collector output stage also allows the output to approach the negative supply during low-level input conditions. Typical applications include automotive battery and power-supply monitoring, overvoltage and undervoltage detection, motor and solenoid control, sensor conditioning, and window or lighting logic. It is also appropriate for industrial control systems requiring a comparator that can operate across a wide supply range without drawing supply current that changes significantly with voltage. When designing around the LM2903QPWRQ1, verify logic-level compatibility between the open-collector output and the connected microcontroller or system logic. Provide a suitable pull-up resistor at each output, keep input and output traces short, and place bypass capacitance close to the supply pins. Consider input common-mode limits carefully when signals exceed the supply rails. This page consolidates the manufacturer’s automotive qualification details, package information, comparator specifications, cross-reference candidates, and practical circuit guidance. It supports faster component selection by placing electrical limits, package compatibility, replacement considerations, and application guidance in one engineering-oriented reference.

RFQ پەیوەندی
LM2903QS-13 - 36V Dual Precision Comparator | Diodes Incorporated
LM2903QS-13

LM2903QS-13 - 36V Dual Precision Comparator | Diodes Incorporated

The Diodes Incorporated LM2903QS-13 is a dual precision voltage comparator designed for operation from a single supply or split power supplies. Its headline ratings include a 36 V maximum supply voltage, 2 mV input offset voltage, 25 nA input bias current, 0.6 mA supply current, and 5 nA input offset current. The device is packaged in an 8-pin SOIC and is qualified to AEC-Q100 for automotive applications. A voltage comparator is an analog interface IC that evaluates two input voltages and switches its output when one input becomes higher than the other. Within the semiconductor hierarchy, a comparator belongs to the amplifier IC family, supports signal conditioning, and is frequently used to bridge low-level analog measurements to digital logic. The LM2903 contains two independent comparators, allowing one package to monitor two thresholds or perform two independent decisions. The low input offset and bias-current characteristics support precise threshold decisions when signals originate from sensors, dividers, or low-level analog stages. The common-mode input range includes ground, a useful property for single-supply systems whose signals remain near the lower rail. Open-collector outputs also allow the two channels to be connected together for wired-AND operation and permit external pull-up resistors to establish the logic-high voltage independently of the comparator supply. The LM2903 architecture emphasizes low power consumption and broad supply compatibility rather than high-speed comparator performance. According to the Diodes Incorporated datasheet, the series supports single-supply operation over a wide voltage range and split-supply operation as well. This makes it suitable for industrial, automotive, and embedded systems where a sensing element compares a variable voltage against a reference before driving a control, fault, or sequencing circuit. Typical applications include supply sequencing, battery and power-system threshold detection, sensor signal conditioning, window-comparator implementations, overvoltage and undervoltage protection, and general digital-logic interfacing. Two independent channels can implement a two-threshold system, compare two sensor signals, or provide one always-enabled channel and one conditionally monitored channel. The 8-pin SOIC footprint is convenient for conventional surface-mount assembly. The principal design consideration is the open-collector output. Each output requires a pull-up resistor to the appropriate logic supply, and the selected resistor must satisfy the output sink-current and rise-time requirements. Inputs should also remain within their specified common-mode and differential ranges, while supply decoupling should be placed close to the device to limit switching-induced disturbance. This product record combines the LM2903QS-13 electrical identity, automotive-grade package information, family-level replacement context, and application-focused design guidance. It helps engineers identify the correct SOIC-8 part, understand its threshold-measurement role, and compare it with same-footprint dual-comparator options before finalizing a PCB or BOM revision.

RFQ پەیوەندی
LM2903QTH-13 Dual 36V Comparator, TSSOP-8 | Diodes Inc
LM2903QTH-13

LM2903QTH-13 Dual 36V Comparator, TSSOP-8 | Diodes Inc

The Diodes Incorporated LM2903QTH-13 is a dual differential voltage comparator with two independent precision channels, a 36 V maximum supply rating, 2 mV input offset voltage, 25 nA input bias current and 0.6 mA typical supply current per channel, housed in an 8-pin TSSOP surface-mount package. A voltage comparator is an analog integrated circuit that compares two input voltages and converts the result into a logic-level output that indicates which input is higher. Within the semiconductor hierarchy, a comparator sits in the linear IC family alongside op amps and voltage references, and it is the simplest building block for threshold detection, level translation and open-loop control functions. Key features of the LM2903QTH-13 include AEC-Q100 Grade 1 automotive qualification, RoHS3 and REACH compliance, MSL Level 1 moisture sensitivity, and the use of green mold compound, all supporting automotive programs that require PPAP documentation. The device shares industry-standard 8-pin pinouts with the wider LM2903 and LM393 families, which makes board requalification and cross-brand second sourcing straightforward. Low quiescent current keeps the part attractive for always-on battery-powered sensing systems. Technically, the device contains two independent amplifier and output stages. Each channel offers differential inputs and an open-collector (open-drain) output stage, so an external pull-up resistor is required on every output. The wide 36 V supply ceiling allows the inputs and outputs to sit well above the logic rail of the controlling MCU, simplifying direct interface to 5 V, 12 V or 24 V systems without level shifters. The low input bias and offset currents minimize error when driving high-impedance sensor networks. Typical applications include automotive sensor interface and battery monitoring, industrial control and threshold detection, DC-DC converter current-limit loops, over-temperature protection circuits in power modules, and general-purpose logic level shifting where a pulled-up open-collector output is acceptable. When designing with the LM2903QTH-13, always fit pull-up resistors on OUT1 and OUT2, keep input common-mode voltage inside the supply range, and give each supply pin a local 100 nF decoupling capacitor close to the pad. Tie the unused channel inputs to a defined voltage within the supply range so that output state stays predictable. This page brings together verified distributor listings, drop-in alternatives across TI and Diodes, pin-level detail and practical layout notes that go beyond the basic orderable-parts listings.

RFQ پەیوەندی
LM2903S-13 - Dual 36V Differential Comparator | Diodes
LM2903S-13

LM2903S-13 - Dual 36V Differential Comparator | Diodes

Diodes Incorporated LM2903S-13 is a dual differential comparator in an 8-pin SOIC package, with a 36 V maximum supply rating, 20 mA output current capability, and 25 nA input bias current rating. It contains two independent comparators, allowing one package to provide two separately controlled threshold-detection or level-shifting channels. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. Within the broader hierarchy of comparator IC, voltage comparator, analog IC, and semiconductor, the LM2903S-13 is intended for general-purpose signal conditioning, threshold detection, and logic-interface applications. Its dual-channel architecture improves board utilization while keeping the two channels electrically independent. Key features include a 36 V maximum total supply voltage, operation from a single supply or split supplies, and an input common-mode range that includes ground. The open-collector outputs are designed to interface with TTL, MOS, and CMOS logic. Each comparator can drive an external pull-up network, making the device useful when a wired-AND function or level translation is required. The stated 25 nA input bias current supports applications where input bias effects must be controlled. The LM2903 family uses an open-collector output architecture rather than a push-pull or rail-to-rail CMOS output. When the output transistor is off, the output voltage is set by the pull-up resistor and its connected supply. When the output transistor is on, the output approaches ground while remaining within the device's output-current capability. This architecture provides flexibility in interface voltage, but it also requires an external pull-up resistor and suitable attention to pull-up current. Typical applications include two-threshold monitoring, zero-cross detection, sensor-signal conditioning, relay or solenoid drive interfaces, window comparators, and general digital logic level translation. The device can also support dual-polarity sensing when powered from split supplies. Its 8-pin SOIC package is convenient for conventional through-hole assembly and hand rework, although modern high-density designs may prefer a smaller surface-mount package when one is qualified. For reliable operation, keep the total supply voltage within the 36 V rating and observe the absolute maximum input and output limits listed in the manufacturer datasheet. Place the pull-up resistor close to the output net, maintain a continuous ground return, and account for the open-collector output's rise time, which is determined by output capacitance and pull-up resistance rather than by a dedicated push-pull driver. This product page combines the LM2903S-13 device identity, package details, manufacturer-family information, sourcing references, pin-compatible alternatives, and application-oriented design guidance. It is structured to help engineers evaluate the comparator electrically before deciding whether the 8-pin SOIC implementation matches the assembly, protection, interface, and lifecycle requirements of the target design.

RFQ پەیوەندی
LM2903ST - Dual Low-Power Comparator, 36V | STMicroelectronics
LM2903ST

LM2903ST - Dual Low-Power Comparator, 36V | STMicroelectronics

The STMicroelectronics LM2903ST is a low-power dual voltage comparator with two independent open-collector comparator channels, operating from a wide single supply of +2 V to +36 V or dual supplies of ±1 V to ±18 V, drawing only 0.4 mA of supply current, and housed in an 8-pin MiniSO surface-mount package. A voltage comparator is an analog integrated circuit that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier and analog signal-chain hierarchy: comparator -> amplifier IC -> analog IC -> semiconductor. Unlike operational amplifiers, comparators are designed for fast, saturated switching between output states, and the LM2903's open-collector output stage lets the output be pulled to any logic level via an external pull-up resistor, enabling interfacing between different voltage domains. Key features of the LM2903ST include the very wide 2 V to 36 V supply range, which covers 3.3 V, 5 V, 12 V, 24 V, and industrial 36 V rails from a single device; a very low supply current of 0.4 mA that is largely independent of supply voltage (approximately 1 mW per comparator at +5 V); a low input bias current of 25 nA typical; and a low input offset current of ±5 nA typical. The common-mode input range extends to ground, allowing sensing of signals referenced to the negative rail. Technically, the LM2903ST uses a bipolar process optimized for low quiescent power rather than speed. Its open-collector outputs can be wire-ORed, and the device is qualified and characterized for automotive use per AEC-Q100 within the LM2903 family, making it robust across industrial and vehicular temperature environments. Propagation behavior suits threshold detection, level shifting, and slow-to-medium-speed switching rather than high-speed clocking. Typical applications include battery chargers and battery-powered instruments, industrial limit comparators and window detectors, automotive sensor threshold detection, square-wave and relaxation oscillators, and level-shifting interfaces between logic families with different supply rails. When designing with this part, always fit an external pull-up resistor on each output (typically 3 kOhm to 15 kOhm) since the outputs are open collector; also account for input differential voltage limits at high supply rails. This page adds value beyond the manufacturer datasheet by combining verified specifications, drop-in alternatives, practical design notes, and application guidance in a single citable reference. Request current pricing and stock through the Request a Quote form on this page.

RFQ پەیوەندی
LM2903TH-13 Dual Differential Comparator | Diodes
LM2903TH-13

LM2903TH-13 Dual Differential Comparator | Diodes

Diodes Incorporated LM2903TH-13 is a dual differential comparator designed for general-purpose analog signal comparison, with two independent comparator channels and an 8-pin TSSOP package. The device operates from 2 V to 36 V, accepts input voltages spanning approximately ±18 V in the dual-supply configuration, and provides a maximum input offset voltage of 7 mV. These characteristics position it for industrial control, sensor interfacing, voltage-threshold detection, and general analog decision-making circuits. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator evaluates the voltage difference between its inverting and non-inverting inputs. This function is placed within the hierarchy of comparator integrated circuits, analog signal-processing ICs, semiconductor devices, and electronic control systems. Unlike a general-purpose operational amplifier used primarily for linear amplification, a comparator is optimized for fast, decisive output-state transitions. The LM2903 family provides two channels in one package, reducing component count and PCB space in dual-threshold applications. Its 2 V to 36 V supply capability supports operation from low-voltage analog systems through substantially higher industrial voltage ranges. The 7 mV maximum input offset specification limits the input difference that can be recognized as a deliberate transition, making the device suitable for threshold monitoring when board-level signal integrity and input conditioning are properly controlled. The dual differential architecture allows two independent comparisons within one IC. Each channel can monitor a sensor signal against a reference, supervise a supply rail, or establish an upper and lower control boundary. Its wide operating-voltage range is especially useful where input signals may exceed the nominal supply of a low-voltage controller. The 8-TSSOP package also supports compact surface-mount layouts, although thermal performance and unused-channel handling remain important design considerations. Typical uses include industrial motor-control logic, power-supply supervision, temperature-sensor interfaces, battery monitoring, overvoltage detection, and general-purpose threshold switching. For dual-polarity sensing, the comparator can operate from single or dual supplies. For a single-supply design, the output reference and input signal levels must remain compatible with the supply voltage and the logic thresholds of the following digital device. PCB design should keep sensitive comparison inputs away from switching nodes and high-current return paths. Place input-referenced components close to the corresponding pins, maintain a stable ground reference, and account for input bias current when using high-source-impedance sensors. If only one comparator channel is required, verify the manufacturer's guidance for the unused channel so that it does not introduce unstable behavior or excess switching activity. This product page combines the LM2903TH-13 identification, package information, technical specifications, sourcing workflow, verified drop-in alternatives, and practical comparison guidance. It is intended to help engineers determine whether the dual comparator's voltage range, offset limit, pin compatibility, and surface-mount format match a specific analog-control design.

RFQ پەیوەندی
LM2903VDG - Dual 2-36V Open-Collector Comparator | onsemi
LM2903VDG

LM2903VDG - Dual 2-36V Open-Collector Comparator | onsemi

The onsemi LM2903VDG is a dual differential voltage comparator designed for single or split-supply operation over a 2 V to 36 V supply range. Each half of the device provides an open-collector output, rail-to-rail input capability, and independent input and output pins. The component is offered in an 8-pin SOIC package for surface-mount industrial, automotive, and consumer electronic assemblies. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM2903 series belongs to the comparator hierarchy, which also includes the broader category of analog interface ICs. Its two independent channels allow one package to implement two comparison functions while avoiding the common-mode limitations associated with older single-supply comparators. The principal features of the LM2903VDG include two independent precision comparator channels, open-collector outputs suitable for pulling a logic node low, operation from a single 2 V supply or split supplies, and an extended temperature range of -40 °C to 125 °C. Maximum input offset voltage is 15 mV, maximum average input bias current is 0.5 µA, and typical response time is 1.5 µs. The open-collector architecture requires an external pull-up resistor when driving CMOS or other logic families. Each channel contains non-inverting and inverting inputs, an output, and a common power-supply connection. The two channels operate independently, but both share the same package pins for ground and positive supply. Because the outputs are open collectors, they can remain in a high-impedance state until an external pull-up establishes the logic-high voltage. This feature also permits several open-collector outputs to share a bus when the application requires wired logic behavior. Typical uses include automotive sensing interfaces, industrial control and monitoring circuits, battery-powered equipment, consumer electronics, and general-purpose threshold detection. A common example is comparing a divided sensor signal with a reference voltage, where the comparator output indicates whether the measured value is above or below the selected threshold. The 2 V minimum supply permits operation from low-voltage rails, while the 36 V maximum supports applications with higher industrial supply levels. Designers should account for the open-collector output when selecting the pull-up resistor and logic family. The resistor must be small enough to achieve the required output rise time but large enough to limit pull-up current when the transistor is saturated. Input-referred offset and bias-current errors should also be included when the comparator threshold requires high accuracy. This product page combines the exact LM2903VDG ordering information with technical characteristics, verified source links, application guidance, and same-footprint replacement analysis. It is structured to help engineers identify suitability, evaluate alternatives, and plan PCB implementation without overlooking the electrical distinctions that matter in comparator designs.

RFQ پەیوەندی
LM2903VDR2G - Dual Open-Collector Comparator | onsemi
LM2903VDR2G

LM2903VDR2G - Dual Open-Collector Comparator | onsemi

The onsemi LM2903VDR2G is a dual independent precision voltage comparator with open-collector outputs, a supply-voltage rating of 2 V to 36 V, and an 8-pin SOIC package. Each comparator can operate from a single supply or from split supplies, while its input common-mode range extends to ground for single-supply threshold detection. The device supports a differential input range of ±18 V, has a response time of 1.5 µs, and offers input offset voltage as low as 2.0 mV. Its open-collector outputs permit wired-AND operation and require an external pull-up resistor. A voltage comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference crosses a defined threshold. In the product hierarchy, the LM2903VDR2G is a comparator, within the broader amplifier and comparator IC family, and ultimately belongs to the semiconductor and analog signal-processing categories. The LM2903 series provides two independent comparison channels in one package, reducing board area compared with two separate single comparators. Key features include independent comparator operation, single or split-supply capability, a common-mode input range extending to ground, and open-collector outputs that support wired-AND logic. The 1.5 µs response time is suitable for threshold monitoring and general-purpose signal conditioning, although it is not optimized for the very low latency required by high-speed edge-detection systems. The manufacturer identifies automotive, industrial, and consumer electronics as suitable application areas. Each channel compares a non-inverting input with an inverting input. The differential input voltage can extend to ±18 V, while the 2 V to 36 V supply rating supports single-rail operation from 2 V through 36 V and split-rail operation with an input range from -1 V through 18 V on either side of ground. The open-collector transistor can sink output current while remaining in a high-impedance state when inactive, so the pull-up resistor determines the output high voltage and limits sink current. Typical applications include battery-voltage monitoring, overvoltage and undervoltage protection, industrial control-interface detection, sensor threshold conditioning, and ground-referenced digital logic interfaces. In each case, the reference network establishes the switching threshold, while the open-collector output can drive a pull-up, relay-driver input, or logic gate. Designers should verify the required output sink current and choose a resistor value that balances current consumption against output rise time. For reliable operation, place the pull-up resistor close to the output and maintain short input traces to reduce sensitivity to injected noise. Check input and output behavior at both supply extremes, confirm that the signal source stays within the common-mode range, and account for offset voltage when defining a precise switching threshold. The manufacturer datasheet is the controlling reference for full electrical limits, test conditions, and connection details. This product page combines the principal LM2903VDR2G specifications, application guidance, drop-in alternatives, and design considerations to support faster component selection and PCB planning.

RFQ پەیوەندی
LM2903VQDR - Dual Differential Comparator | Texas Instruments
LM2903VQDR

LM2903VQDR - Dual Differential Comparator | Texas Instruments

Texas Instruments LM2903VQDR is a dual differential comparator with open-collector outputs, a 2 V to 36 V supply range, and an operating temperature range of -40°C to +125°C, housed in an 8-pin SOIC (D) package. Each channel compares one differential input pair and provides an open-collector output suitable for wired logic, relay drive, and industrial sensing circuits. A differential comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903V belongs to the comparator hierarchy: differential comparator, voltage comparator, analog comparator, and ultimately semiconductor. Its two channels allow one packaged device to perform two independent threshold decisions, reducing component count when a system requires multiple sensing or control functions. The device operates from a 2 V minimum supply to a 36 V maximum supply, giving it broad compatibility with industrial control voltages. The distributor specifications identify an input bias current of 0.5 nA and a supply current of 0.8 mA. Its open-collector outputs can sink output current from external pull-up circuitry, and the 8-pin SOIC package supports conventional surface-mount assembly and automated inspection. The enhanced-voltage LM2903V family is intended for applications that benefit from wide supply-voltage operation and low input bias current. A high-impedance input stage can limit loading on slow sensor signals, while the open-collector output provides flexibility in voltage-domain interfacing. Because the output transistor is open, the external pull-up voltage can be selected independently within the design's logic constraints. Typical uses include industrial process-limit detection, automotive and battery-powered control systems, motor and relay interfaces, window-comparator circuits, and low-frequency sensor conditioning. In a threshold circuit, one input can receive the sensed voltage and the other can receive a reference. The output changes state when their relationship crosses the configured threshold, allowing the result to drive another logic stage or an external transistor. Design the pull-up network carefully because it determines output voltage, rise time, and available sink current. Place the pull-up resistor close to the open-collector output, keep comparator inputs away from switching-current paths, and provide a stable reference with low noise when threshold accuracy matters. The open-collector pins can also be tied together for wired-AND behavior when the circuit requires multiple fault signals to share one node. This product page combines device specifications, application guidance, drop-in replacement options, and parameter-by-parameter comparison information. It helps engineers determine whether the LM2903VQDR's voltage range, low input bias current, open-collector interface, and extended temperature coverage match the mechanical and electrical requirements of a specific PCB design.

RFQ پەیوەندی
LM2903VQDRG4 - Dual 36V Open-Collector Comparator | TI
LM2903VQDRG4

LM2903VQDRG4 - Dual 36V Open-Collector Comparator | TI

The Texas Instruments LM2903VQDRG4 is a dual differential comparator with two independent comparator channels, a 2 V to 36 V supply-voltage range, and an open-collector output configuration. The device is packaged in an 8-pin SOIC package and is specified for operation from -40 °C to 125 °C. Typical input offset voltage is 15 mV, response time is 1.3 microseconds, and supply current is 1 mA. A differential voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the comparator hierarchy within the broader amplifier and signal-conditioning IC category. Its differential inputs allow it to detect positive or negative voltage relationships, while the open-collector output supports wired logic, relay drivers, and interface functions. The LM2903VQDRG4 provides two independent comparators within one package. Each channel can operate from a single supply or from dual supplies when the total supply span and positive-to-negative rail requirements are satisfied. Open-collector outputs require an external pull-up resistor and can be connected to a common bus when only one output is active at a time. This arrangement is useful when multiple sensing channels must share a digital or microcontroller input. Key electrical characteristics include a 2 V to 36 V total supply range, 15 mV input offset voltage, 1.3 microsecond response time, and 1 mA supply current. The enhanced-voltage LM2903V version supports operation up to 36 V, which gives designers additional margin for industrial supply transients and automotive-style sensing environments when the board-level protection and operating requirements are appropriate. Typical uses include overvoltage and undervoltage detection, sensor threshold conditioning, industrial control interfaces, battery monitoring, window or level sensing, and general digital threshold detection. Two independent channels can also be used separately for a high-side and low-side limit, a differential sensor monitor, or a pair of unrelated comparator functions. For PCB implementation, keep input and output traces short, provide a stable reference or return path, and place the required pull-up resistor close to the open-collector output. Account for input common-mode limits when the inputs can move outside the supply rails. Stable bypass capacitance near the supply pins helps reduce supply noise and output disturbance. This product page combines the manufacturer device data, package information, compatibility details, application guidance, and practical design notes needed to evaluate the LM2903VQDRG4 before PCB design, sourcing, or replacement planning.

RFQ پەیوەندی
LM2903VQDRG4Q1 - 36V Automotive Dual Comparator | Texas Instruments
LM2903VQDRG4Q1

LM2903VQDRG4Q1 - 36V Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903VQDRG4Q1 is an automotive dual differential comparator with two independent open-collector outputs, a 2 V to 36 V single-supply operating range, and operation from dual supplies of ±18 V. Each comparator supports rail-to-rail input operation, and the device is available in an 8-pin SOIC package rated for AEC-Q100 Grade 0 and Grade 1 automotive applications. Typical supply-current consumption is 0.4 mA per comparator. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a selected threshold. The LM2903 family combines two independent comparators in one package, providing greater functional flexibility than a single comparator while requiring only one device. Its open-collector outputs can sink current and support wired logic, lamp drivers, or interface with pull-up resistors and external transistors. Automotive qualification is the principal differentiator of the LM2903VQDRG4Q1. The device is qualified to AEC-Q100 Grade 0 and Grade 1, and the manufacturer documentation identifies ESD protection exceeding 1000 V under MIL-STD-883, Method 3015 and exceeding 100 V with the machine model. The dual architecture supports single-supply operation from 2 V to 36 V or split-supply operation where the total supply difference remains within the device rating. Each channel has its own differential input pair, output, and output-strobe capability. The input common-mode range extends across the supply rails, allowing the comparator to monitor low-level sensor signals without separate input protection in many applications. Open-collector outputs avoid push-pull output contention, but they require a pull-up resistor when a logic-high output voltage is required. Typical propagation delay is listed at 0.3 microseconds for the automotive variant. Typical uses include battery monitoring, automotive sensor conditioning, window and seat-position sensing, overvoltage detection, fan control, and industrial control modules. The dual supply capability is useful in systems with positive and negative rails, while the wide single-supply range accommodates 5 V, 12 V, and 24 V automotive electrical environments. The device should be paired with input filtering where noisy signals could cause repeated output transitions. Layout and stability require attention near the supply pins. Place the supply bypass capacitor close to pin 8 and the ground connection close to pin 4, keep comparator inputs away from output and supply traces, and connect open-collector pull-ups to a compatible logic rail. Check absolute maximum voltage limits, input common-mode range, output-current capability, and the pull-up voltage before finalizing the external circuit. This page combines automotive qualification, operating limits, package details, lifecycle information, and drop-in family alternatives with practical PCB and application guidance. It is intended to help engineers select or replace the LM2903VQDRG4Q1 in 8-pin SOIC designs while accounting for supply architecture, output loading, and automotive qualification requirements.

RFQ پەیوەندی