Amplifier ICs
بەرهەمەکان (3,200+)
LM324KADR - Quad 30V 1.2MHz Op Amp | Texas Instruments
Texas Instruments LM324KADR is a quad, general-purpose operational amplifier rated for a 30 V maximum supply, 1.2 MHz gain-bandwidth performance, and 3 mV input offset voltage. The device contains four independent, internally frequency-compensated amplifiers and is available in a 14-pin SOIC (D) package. Its improved ESD withstand rating is 2 kV, making it suitable for industrial control, instrumentation, signal conditioning, and low-cost general-purpose analog systems. An operational amplifier is a high-gain differential amplifier whose external feedback network determines its behavior. In the signal-chain hierarchy, the LM324KADR belongs to the operational-amplifier family within amplifier ICs and analog signal-chain devices. Unlike a single-amplifier package, this quad device integrates four independent amplifiers, allowing one component to support multiple analog channels while reducing package count and board area. Key features include four independent amplifiers, operation from a single supply or split supplies, a 1.2 MHz gain-bandwidth product, and a 3 mV input offset voltage. The 14-pin SOIC package also provides improved 2 kV ESD protection. These characteristics make the LM324KADR appropriate for low-frequency control loops, sensor amplification, buffering, and general-purpose signal processing where a broad supply-voltage range and economical quad integration are more important than precision or high-speed performance. The amplifiers are internally frequency compensated, which simplifies closed-loop design when stable operation is required. The 30 V maximum supply supports higher-voltage industrial interfaces than many low-voltage rail-to-rail amplifier families. Split-supply operation is also possible when the difference between the supplies remains within the device's permitted range. Its 1.2 MHz bandwidth is adequate for audio-band and general control applications but is not intended for high-speed instrumentation or RF signal paths. Typical uses include 4–20 mA current-loop receivers, industrial sensor interfaces, active low-pass filters, audio preamplifier stages, relay and motor-control loops, and general instrumentation. Using four amplifiers in one SOIC package simplifies multi-channel designs, although each amplifier has an independent signal path and shares the common supply and ground pins. PCB design should keep sensitive input and feedback traces short, place input bypassing close to the supply pins, and maintain a stable ground reference around the device. Do not substitute a rail-to-rail amplifier without checking input common-mode range, output swing, offset voltage, bandwidth, stability, and maximum supply voltage; those electrical differences can change the behavior of an existing LM324-based circuit.
LM324KADRG4 - Quad 32V Op Amp with 2kV ESD | Texas Instruments
The Texas Instruments LM324KADRG4 is a quadruple general-purpose operational amplifier in a 14-pin SOIC package, with four independent, frequency-compensated amplifiers that can operate from a single supply or split supplies. Its 3 V to 32 V operating range, typical 0.8 mA supply-current drain, and common-mode input range that includes ground make it suitable for cost-sensitive industrial and consumer signal-conditioning circuits. The LM324 family combines a high-gain differential input stage with single-ended output stages designed for straightforward single-supply operation. According to the Texas Instruments LMx24, LMx24x, LMx24xx, LM2902, LM2902x, LM2902xx and LM2902xxx datasheet, operation from split supplies is also possible when the total supply difference is 3 V to 32 V. This flexibility supports legacy industrial control, sensor conditioning, audio preamplification, and low-frequency filter designs. Key characteristics include four amplifiers in one package, a 3 V to 32 V supply range, low quiescent current of approximately 0.8 mA typical, and input common-mode voltage that includes ground. The LM324KADRG4 variant also carries 2 kV ESD protection according to its Texas Instruments product listing. The 14-pin SOIC footprint allows direct substitution with compatible LM324-family devices where electrical and temperature requirements are equivalent. The internal architecture favors general-purpose precision over high-speed or low-noise performance. Each channel is internally frequency compensated, so no external compensation network is required for unity-gain voltage-follower or non-inverting amplifier configurations. Input bias and offset currents remain part of the error budget when the amplifier operates with high-impedance sensors. Typical uses include four-channel sensor interfaces, low-frequency active filters, buffered ADC inputs, audio preamplifier stages, and general DC signal conditioning. Because all four channels share one package, ground-return and supply-bypass placement directly affect every amplifier and should follow the pinout and layout guidance in the manufacturer datasheet. For new single-rail designs, first verify output swing, input common-mode limits, output-current capability, and noise at the intended signal bandwidth. The LM324 remains effective where its supply range and low quiescent current outweigh the lower noise, wider bandwidth, and faster slew rate available from modern precision operational amplifiers. This page also organizes practical substitution options, application guidance, and design checks that are not presented together on a standard distributor listing.
LM324KAN - 14-PDIP Quad Operational Amplifier | Texas Instruments
The Texas Instruments LM324KAN is a four-circuit general-purpose operational amplifier in a 14-pin PDIP package, designed for low-power operation from a single power supply across a wide voltage range. The device provides four independent amplifier sections in one package, making it suitable for general-purpose signal conditioning, buffering, voltage amplification, and feedback-control circuits. The LM324KAN is identified as the military-temperature-grade ordering option within the LM324 family. An operational amplifier is an active analog device that amplifies the difference between its two inputs. The LM324 family belongs to the broader hierarchy of operational amplifiers, analog amplifiers, linear integrated circuits, and signal-chain semiconductors. Its single-supply capability allows operation from one positive rail and ground, although the complete electrical limits and common-mode behavior should be confirmed in the manufacturer datasheet before fixing system voltages. The primary feature of the LM324KAN is its integration of four general-purpose amplifier channels into one 14-pin PDIP. This reduces component count and board area compared with four single-amplifier packages. The through-hole PDIP format also suits educational equipment, industrial control prototypes, audio projects, legacy instruments, and maintenance applications where socketed or hand-soldered installation is common. Each amplifier section includes differential input and output connections arranged in a standard quad-op-amp layout. Pin 11 supplies the positive rail, pin 4 connects to the negative rail, and pins 1, 7, 8, and 14 provide the four outputs. Input pins 2 and 3, 5 and 6, 9 and 10, and 12 and 13 form the four differential input pairs. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks or socket connections. Typical uses include audio preamplification, sensor-signal conditioning, low-frequency filtering, active feedback, sample-and-hold support, and general instrumentation. Because the LM324KAN is a general-purpose amplifier rather than a precision or high-speed device, its noise, input-bias-current, slew-rate, output-current, and input-offset-voltage characteristics should be checked against the signal amplitude, source impedance, bandwidth, and required accuracy of the design. When designing around this device, check the maximum supply voltage and input common-mode range at the selected operating voltage. Decoupling capacitors should be placed close to the supply pins, and unused amplifier sections should be configured according to the manufacturer recommendations instead of being left floating. The DIP footprint also requires adequate spacing for through-hole insertion and soldering access. This page combines device identification, pin-level guidance, application analysis, drop-in alternatives, and practical design notes to support schematic capture, PCB layout, sourcing, and legacy-product maintenance for the LM324KAN.
LM324KANSR - 1.2MHz Quad Op Amp | Texas Instruments
The Texas Instruments LM324KANSR is a four-circuit general-purpose operational amplifier with a 1.2 MHz gain-bandwidth product, supplied in a 14-pin small-outline integrated-circuit package. The device contains four independent, internally frequency-compensated amplifiers designed for general-purpose signal conditioning, control, and analog signal-processing applications. An operational amplifier, commonly abbreviated op amp, is a high-gain differential amplifier. Within the broader semiconductor hierarchy, an op amp belongs to the linear amplifier family, which sits within amplifier ICs and analog signal-processing devices. LM324-type amplifiers are valued for straightforward operation from single or split supplies, broad input-voltage flexibility, and low cost. The LM324KANSR is specifically identified as a 14-SO device. The four-amplifier configuration allows one package to serve several independent signal paths. Its 1.2 MHz gain-bandwidth product supports general-purpose feedback networks, instrumentation-style buffering, comparators with suitable hysteresis, differential summing circuits, and low-frequency active-filter stages. Because the amplifiers are frequency compensated, many common closed-loop configurations do not require external compensation components. Each circuit operates independently, allowing four unrelated signals to be processed simultaneously while sharing one package and supply connection. The 14-pin arrangement provides four amplifier sections, supply pins, and input or output connections for every channel. Its standard general-purpose classification supports broad industrial, instrumentation, control, audio, and interface applications where moderate bandwidth and precision are sufficient. Typical uses include sensor-signal conditioning, low-level signal amplification, active filtering, control-loop support, transducer interfacing, and general analog conditioning. Because the four channels operate independently, a single device can implement a sensor amplifier, output buffer, active filter section, and auxiliary gain stage when the required accuracy and bandwidth meet the application requirements. When assigning PCB tracks, use the pin-description table in the Texas Instruments datasheet and preserve the pin order associated with the 14-SO outline. Decouple the supply pins with the capacitance and placement required by the datasheet, and verify input and output common-mode limits for every operating condition. Stable feedback-network values and proper grounding are important because the 1.2 MHz bandwidth limits high-frequency gain and stability margin. This page combines the exact LM324KANSR ordering information, package details, sourcing guidance, drop-in replacement analysis, and practical design guidance to support faster component selection, PCB implementation, and legacy-design maintenance.
LM324KAPW - Quad 2 kV ESD Op Amp | Texas Instruments
Texas Instruments LM324KAPW is a quad general-purpose operational amplifier with 2 kV ESD protection, four amplifier channels, and a 14-pin TSSOP package. The device is intended for single-supply operation and is identified in manufacturer-related listings as a standard general-purpose amplifier. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare two input voltages and drive an output according to their difference. The quad LM324 combines four amplifiers in one package, reducing component count and simplifying layout in audio, sensor, filtering, and control circuits. As a general-purpose amplifier, it belongs to the operational-amplifier hierarchy within integrated circuits and analog signal processing. The principal device-level features include four amplifier channels, a 14-pin TSSOP package, operation from a single positive supply, and 2 kV ESD protection. Searchable manufacturer product information identifies the LM324KAPW as a general-purpose amplifier, while comparison data lists a gain-bandwidth product of 1.2 MHz. The four-channel integration allows one package to support independent filtering, buffering, amplification, or feedback-control functions. The LM324 architecture is suited to low-cost, low-frequency analog designs where moderate bandwidth and straightforward external compensation are sufficient. Its quad organization can reduce board area compared with four single-amplifier packages. Designers should still account for input common-mode range, output swing, supply headroom, input bias current, and stability when selecting external feedback components for a specific topology. Typical applications include low-frequency audio signal conditioning, resistive sensor amplification, active filtering, DC error amplification, and general feedback control. The same package can also be used for multi-stage signal conditioning where four channels must operate independently. For instrumentation or precision measurement designs, verify the complete electrical limits and noise performance against the manufacturer datasheet before finalizing the gain and bandwidth budget. PCB implementation should preserve short feedback paths, provide an unobstructed ground return, and decouple the supply close to the IC. The TSSOP-14 lead pitch also makes the device practical for compact, high-density analog assemblies. Avoid long signal traces between input and output nodes because parasitic capacitance can alter feedback behavior or cause instability in high-gain configurations. This product record combines manufacturer-related product descriptions, package information, cross-reference findings, and practical engineering guidance. The comparison section distinguishes true pin-compatible options from alternatives that may require a footprint or pinout change, while the design notes emphasize supply bypassing, feedback layout, and stability checks that are important when replacing a quad amplifier in an existing design.
LM324KAPWR - Quad 2 kV ESD Op Amp | Texas Instruments (Tape & Reel)
Texas Instruments LM324KAPWR is a quad general-purpose operational amplifier with 2 kV ESD protection, four amplifier channels, and a 14-pin TSSOP package. The device is intended for single-supply operation and is identified in manufacturer-related listings as a standard general-purpose amplifier. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare two input voltages and drive an output according to their difference. The quad LM324 combines four amplifiers in one package, reducing component count and simplifying layout in audio, sensor, filtering, and control circuits. As a general-purpose amplifier, it belongs to the operational-amplifier hierarchy within integrated circuits and analog signal processing. The principal device-level features include four amplifier channels, a 14-pin TSSOP package, operation from a single positive supply, and 2 kV ESD protection. Searchable manufacturer product information identifies the LM324KAPWR as a general-purpose amplifier, while comparison data lists a gain-bandwidth product of 1.2 MHz. The four-channel integration allows one package to support independent filtering, buffering, amplification, or feedback-control functions. The LM324 architecture is suited to low-cost, low-frequency analog designs where moderate bandwidth and straightforward external compensation are sufficient. Its quad organization can reduce board area compared with four single-amplifier packages. Designers should still account for input common-mode range, output swing, supply headroom, input bias current, and stability when selecting external feedback components for a specific topology. Typical applications include low-frequency audio signal conditioning, resistive sensor amplification, active filtering, DC error amplification, and general feedback control. The same package can also be used for multi-stage signal conditioning where four channels must operate independently. For instrumentation or precision measurement designs, verify the complete electrical limits and noise performance against the manufacturer datasheet before finalizing the gain and bandwidth budget. PCB implementation should preserve short feedback paths, provide an unobstructed ground return, and decouple the supply close to the IC. The TSSOP-14 lead pitch also makes the device practical for compact, high-density analog assemblies. Avoid long signal traces between input and output nodes because parasitic capacitance can alter feedback behavior or cause instability in high-gain configurations. This product record combines manufacturer-related product descriptions, package information, cross-reference findings, and practical engineering guidance. The comparison section distinguishes true pin-compatible options from alternatives that may require a footprint or pinout change, while the design notes emphasize supply bypassing, feedback layout, and stability checks that are important when replacing a quad amplifier in an existing design.
LM324KAPWRG4 - Quad 14-TSSOP Op Amp | Texas Instruments
The Texas Instruments LM324KAPWRG4 is a low-power, general-purpose quadruple operational amplifier integrating four amplifiers in a 14-pin TSSOP package. It supports single-supply operation, offers a typical low-supply-current drain of 0.8 mA, and is designed for general-purpose applications that require one amplifier per signal channel. An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify differences between its input terminals. The LM324 family combines four operational amplifiers with supply drain that remains largely independent of supply voltage. Its common-mode input range includes ground, allowing the device to operate from a positive supply while processing signals whose lower excursion approaches the negative supply rail. The LM324KAPWRG4 is identified as a standard general-purpose amplifier with four circuits and 2 kV ESD protection. According to the LM324 manufacturer information, it supports wide supply ranges of up to 26 V for single-supply operation and up to plus or minus 13 V for dual supplies. Its common-mode input capability is especially useful for sensor interfaces, transducer amplifiers, audio paths, and control signals referenced to ground. The four-amplifier configuration reduces the number of packages needed when several independent low-frequency signals must be processed. Each amplifier can operate independently, allowing one LM324KAPWRG4 to implement functions such as two instrumentation-amplifier sections, four voltage followers, or a mixture of summing, buffering, and gain stages. Independent operation requires careful grounding and decoupling so that high-current output stages do not disturb sensitive channels sharing the package. Typical applications include low-cost sensor conditioning, audio preamplification, active filtering, current-to-voltage conversion, and general industrial control. The TSSOP-14 surface-mount package supports compact PCB layouts, but its small thermal dissipation area makes trace and copper-plan consideration important when driving capacitive loads or operating continuously near the supply limits. For layout, place the package power-decoupling capacitor close to the supply pins and connect each ground reference to a low-impedance ground plane. Avoid placing sensitive input traces beside output traces carrying fast transients. Check output-swing and common-mode limits at the actual supply voltage and load before committing the design. This product page combines package, application, and drop-in replacement guidance with practical PCB and signal-integrity considerations. It also distinguishes same-footprint LM324 variants so engineers can review orderable suffixes and functional differences before redesigning an existing 14-TSSOP layout.
LM324KD - Quad 30V 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM324KD is a quad general-purpose operational amplifier rated for supply voltages up to 30 V, with a gain-bandwidth product of 1.2 MHz and improved 2 kV ESD protection. The device contains four independent, frequency-compensated amplifiers in a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, wide. Its combination of single- or dual-supply operation, low input bias current, and broad supply range makes it suitable for general-purpose analog signal conditioning. An operational amplifier, or op amp, is a high-gain differential amplifier used within the wider voltage-amplifier and analog IC hierarchy. LM324-family devices are commonly used for buffering, voltage amplification, current-to-voltage conversion, filtering, comparators, and instrumentation interfaces. Unlike rail-to-rail precision amplifiers, the LM324 uses conventional bipolar input stages and includes internal compensation, allowing straightforward use without an external frequency-compensation network. The LM324KD provides four amplifiers in one package, reducing board area and simplifying designs that require multiple similar analog channels. Its verified supply capability covers 3 V to 32 V for single-supply operation and ±1.5 V to ±16 V for dual-supply operation. The listed per-channel output current capability is 60 mA, while the input bias current is listed as 20 nA. The 1.2 MHz gain-bandwidth product supports moderate-bandwidth closed-loop applications. Each channel is independent and can operate with common input ranges that include ground, making single-supply sensing of signals near 0 V practical. The LM324K family also incorporates improved 2 kV ESD protection, an important consideration for exposed sensor, interface, and control boards. The internal architecture prioritizes forgiving general-purpose operation rather than the low offset, low drift, and rail-to-rail performance expected from precision or modern energy-efficient amplifier families. Typical uses include low-frequency sensor amplifiers, buffered analog inputs, audio preamplification, loop-filter sections, motor and industrial control interfaces, and general instrumentation. The 14-pin SOIC package supports conventional surface-mount assembly, while the four-amplifier configuration can implement two differential channels, four single-ended channels, or a mixture of amplifiers and comparators. Designers should preserve adequate input and output common-mode range, account for the typical 0.5 uA supply current, and verify operation across the full industrial supply range. Decoupling close to the positive and ground pins is recommended, and signal routing should minimize parasitic capacitance around high-impedance input nodes. The published 24-page datasheet and manufacturer product page should be consulted for the complete electrical limits, pin configuration, and test conditions. This page combines verified manufacturer and distributor information, current pricing, package and pinout details, drop-in replacement evidence, and application-focused design guidance. It is intended to help engineers compare the LM324KD with other LM324-family choices while preserving PCB footprint, supply-voltage, and signal-chain compatibility.
LM324KDR - Quad 30V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
The Texas Instruments LM324KDR is a quad general-purpose operational amplifier rated for supply voltages up to 30 V, with a gain-bandwidth product of 1.2 MHz and improved 2 kV ESD protection. The device contains four independent, frequency-compensated amplifiers in a 14-pin SOIC package measuring 0.154 inch, or 3.90 mm, wide. Its combination of single- or dual-supply operation, low input bias current, and broad supply range makes it suitable for general-purpose analog signal conditioning. An operational amplifier, or op amp, is a high-gain differential amplifier used within the wider voltage-amplifier and analog IC hierarchy. LM324-family devices are commonly used for buffering, voltage amplification, current-to-voltage conversion, filtering, comparators, and instrumentation interfaces. Unlike rail-to-rail precision amplifiers, the LM324 uses conventional bipolar input stages and includes internal compensation, allowing straightforward use without an external frequency-compensation network. The LM324KDR provides four amplifiers in one package, reducing board area and simplifying designs that require multiple similar analog channels. Its verified supply capability covers 3 V to 32 V for single-supply operation and ±1.5 V to ±16 V for dual-supply operation. The listed per-channel output current capability is 60 mA, while the input bias current is listed as 20 nA. The 1.2 MHz gain-bandwidth product supports moderate-bandwidth closed-loop applications. Each channel is independent and can operate with common input ranges that include ground, making single-supply sensing of signals near 0 V practical. The LM324K family also incorporates improved 2 kV ESD protection, an important consideration for exposed sensor, interface, and control boards. The internal architecture prioritizes forgiving general-purpose operation rather than the low offset, low drift, and rail-to-rail performance expected from precision or modern energy-efficient amplifier families. Typical uses include low-frequency sensor amplifiers, buffered analog inputs, audio preamplification, loop-filter sections, motor and industrial control interfaces, and general instrumentation. The 14-pin SOIC package supports conventional surface-mount assembly, while the four-amplifier configuration can implement two differential channels, four single-ended channels, or a mixture of amplifiers and comparators. Designers should preserve adequate input and output common-mode range, account for the typical 0.5 uA supply current, and verify operation across the full industrial supply range. Decoupling close to the positive and ground pins is recommended, and signal routing should minimize parasitic capacitance around high-impedance input nodes. The published 24-page datasheet and manufacturer product page should be consulted for the complete electrical limits, pin configuration, and test conditions. This page combines verified manufacturer and distributor information, current pricing, package and pinout details, drop-in replacement evidence, and application-focused design guidance. It is intended to help engineers compare the LM324KDR with other LM324-family choices while preserving PCB footprint, supply-voltage, and signal-chain compatibility.
LM324KN - Quad 14-PDIP General-Purpose Op Amp | Texas Instruments
Texas Instruments LM324KN is a four-circuit general-purpose operational amplifier in a 14-pin PDIP package. The device combines four independent, internally frequency-compensated amplifiers with an operating supply range extending to 36 V, a typical low supply-current drain of 0.8 mA, and input common-mode operation that includes ground. It is designed for single-supply or split-supply operation and includes 2 kV ESD protection. An operational amplifier is an analog signal-conditioning IC that uses feedback to control gain, amplify differential inputs, buffer sensors, and perform general-purpose analog calculations. The LM324 family belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its common-mode input range includes ground, making it useful in circuits powered from a positive rail and sensing signals near 0 V. The four independent channels can perform simultaneous amplification, filtering, buffering, or summing functions while sharing one package. Internal frequency compensation makes the LM324 suitable for general-purpose closed-loop amplifier designs without external compensation networks. Its low 0.8 mA typical supply-current drain helps reduce system power consumption, while the broad supply capability supports industrial and legacy equipment operating from multiple rail voltages. Common applications include sensor-signal conditioning, low-level current-to-voltage conversion, audio preamplification, active filtering, comparators with additional biasing, and general instrumentation. The 14-pin PDIP format also supports manual assembly and through-hole prototyping in laboratories, educational equipment, industrial control systems, and repair products. When designing an LM324KN circuit, verify input and output voltage limits against the selected operating rail, including output swing limitations when driving capacitive loads. Place input compensation or bias resistors close to the relevant amplifier pins, keep feedback loops short, and provide stable bypassing at the supply pins to limit noise and prevent oscillation. This product page combines the LM324KN package and feature information with practical analog-design guidance, application context, verified alternatives, and a parameter comparison for faster component selection.
LM324KNSR - Quad 30-V 1.2-MHz Op Amp | Texas Instruments
The Texas Instruments LM324KNSR is a quadruple general-purpose operational amplifier with four independent, high-gain, frequency-compensated amplifiers, a 30 V maximum supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection in a 14-pin SOIC (NS) package. Each amplifier can operate from a single supply or split supply, making the device useful in general-purpose analog signal-processing circuits. An operational amplifier, or op amp, is a high-gain differential amplifier that compares two input voltages and drives its output to represent their difference. Within the broader semiconductor hierarchy, an op amp is an analog amplifier IC used for signal conditioning, buffering, amplification, filtering, feedback control, and voltage-level conversion. The LM324KNSR integrates four such amplifiers into one package, reducing board area compared with four separate single or dual amplifier packages. The principal device ratings include operation from a single or split supply, a 30 V maximum supply voltage, 1.2 MHz gain-bandwidth bandwidth, and 2 kV improved ESD protection. The manufacturer identifies LM324KNSR as a standard general-purpose amplifier with four circuits and a 14-pin SOP package. Its specified operating-temperature range is 0 to 70 °C, making it appropriate for commercial equipment where an extended industrial temperature rating is not required. The LM324K family is designed for broad compatibility with established LM324-type amplifier boards. Because the four amplifiers share a common package but operate independently, separate signal paths can be implemented within one device. The frequency-compensated architecture simplifies closed-loop use when the amplifier is configured as a standard inverting or non-inverting gain stage, although loop stability and bandwidth still depend on the external feedback network and load. Typical uses include audio preamplification, sensor signal conditioning, current-to-voltage conversion, active filtering, voltage comparison, and general instrumentation. The four-amplifier arrangement is especially useful when a design needs several channels of similar gain and bandwidth, such as multiple sensor inputs or a balanced differential stage followed by additional gain stages. PCB layout should keep input and feedback connections short and route them away from high-current switching nodes. Decoupling capacitors should be placed close to the power pins, while the unused amplifier in any unused channel must be configured according to the Texas Instruments LM324K datasheet rather than left floating. The 14-pin SOIC footprint simplifies replacement on compatible LM324NS-style boards. This product record combines manufacturer specifications, package and ordering information, drop-in candidate analysis, comparison parameters, and practical PCB guidance. It helps engineers evaluate the LM324KNSR for general-purpose analog designs and identify whether a same-footprint LM324-family device is appropriate when supply voltage, temperature grade, or sourcing requirements change.
LM324KPWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM324KPWR is a four-circuit general-purpose operational amplifier with a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection. The device is packaged in a 14-pin TSSOP, combining four amplifiers in a compact surface-mount footprint. Each channel supports the standard op-amp functions of voltage amplification, filtering, buffering, summing, and difference amplification. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to control an output voltage. The LM324 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Its four channels share a positive supply, negative supply, and ground reference, making it useful where several independent low-frequency analog stages are required in the same board area. The principal features include four amplifiers per package, a 1.2 MHz gain-bandwidth product, operation from a single supply or dual supplies, a 30 V maximum total supply rating, and 2 kV ESD protection. These characteristics suit general-purpose signal conditioning rather than precision or high-speed instrumentation. The quad organization also reduces component count and simplifies routing when one board section contains four similar low-frequency channels. Each amplifier uses differential inputs, an output stage, bias compensation, and internal frequency compensation. The common design is intended for stable operation with feedback networks that define closed-loop gain. Because this is a general-purpose amplifier, input offset, input bias current, output-current capability, slew rate, and common-mode limits should be checked against the exact signal levels and load conditions before finalizing a design. Typical uses include sensor-signal conditioning, low-frequency active filters, audio preamplification, comparators with suitable feedback, DC summing and difference stages, and general buffer or gain stages. The 14-pin TSSOP is appropriate for compact industrial, instrumentation, consumer, and embedded-control equipment where four analog channels are preferable to separate single or dual amplifier packages. Layout and stability remain the primary implementation considerations. Keep input and feedback traces short, place compensation or bypass components close to their associated pins, and maintain a common ground reference across all four channels. Avoid long unprotected inputs and place external input clamps where exposed connectors can carry electrostatic discharge. Confirm the selected channel’s input and output swing against the intended supply rails. This page consolidates the exact package, electrical headline ratings, drop-in alternatives, comparison parameters, and practical design guidance for LM324KPWR. It helps engineers identify the correct TI orderable MPN and assess whether the quad general-purpose amplifier meets a circuit’s voltage, bandwidth, ESD, footprint, and sourcing requirements.
LM324LVIDR - 4-Channel 5.5V Op Amp | Texas Instruments
The Texas Instruments LM324LVIDR is a four-channel, general-purpose operational amplifier designed for low-voltage operation from 2.7 V to 5.5 V, with a gain-bandwidth product of 1 MHz and a typical input offset voltage of 3 mV. The device is packaged in a 14-pin SOIC (D) and supports operation from -40°C to 125°C. Four independent amplifiers in one package make it suitable for compact analog signal-conditioning, sensing, filtering, and buffering systems. An operational amplifier, or op amp, is a high-gain differential amplifier that compares two input voltages and drives its output to represent their difference. The LM324LV belongs to the broader operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its four channels can amplify sensor signals, buffer high-impedance sources, perform active filtering, or provide simple differential-to-single-ended conversion when configured with external resistors. The LM324LV family is optimized for supply voltages down to 2.7 V, making it more useful in low-voltage systems than standard LM324 devices intended for wider supply ranges. Its 1 MHz gain-bandwidth product supports general-purpose signal paths rather than high-speed video or precision instrumentation. The 3 mV input offset specification is important for dc applications because it influences the output error after gain is applied and can contribute to input-referred error near the lower end of the input range. Each channel provides practical flexibility for single-supply designs. Input and output behavior depends on the common-mode and output-swing limits, so the circuit must keep signals within the amplifier's supported operating region. The four amplifiers share a common supply voltage, but their input stages are independent, allowing different signals and gains to be processed in one package. Grounding, bypassing, and output-load conditions remain important for stable low-frequency operation. Typical uses include battery-powered sensor interfaces, industrial control signals, audio preamplifier stages, active low-pass filters, transducers, and low-voltage data-acquisition modules. The SOIC-14 package is also convenient for prototyping and conventional surface-mount assembly. Because all four channels are independent, unused amplifiers can be configured as buffers, followers, or signal conditioners rather than left unconnected. For reliable operation, place the supply bypass capacitor close to the positive and ground pins and keep feedback resistors close to the corresponding amplifier inputs. Check input common-mode range and output swing against the actual signal. When replacing a standard LM324, verify voltage range, offset, bandwidth, output-current capability, and stability because the LM324LV is optimized specifically for low-voltage operation. This page combines the LM324LVIDR electrical and package details with application guidance, validated replacement information, comparison parameters, and practical PCB design notes for engineers evaluating a 2.7 V to 5.5 V quad op amp.
LM324LVIPWR - Quad 5.5V 1MHz Op Amp | Texas Instruments
The Texas Instruments LM324LVIPWR is a quad, general-purpose operational amplifier rated for a 5.5 V maximum supply, operating from ±2.75 V to 5.5 V. Each of its four amplifiers provides 1 MHz of gain-bandwidth product and a 3 mV offset-voltage rating. The device is packaged in a 14-pin TSSOP (PW) and is specified across the -40°C to +125°C industrial temperature range. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM324LV belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and integrated circuits. Its quad configuration integrates four amplifiers in one package, reducing board area when a design requires several independent gain stages, buffers, comparators, or current-feedback loops. The LM324LV series is designed for low-voltage operation while retaining the familiar pin arrangement and general-purpose characteristics associated with industry-standard quad amplifiers. The 1 MHz gain-bandwidth product supports audio-frequency and general analog signal conditioning, while the 3 mV offset specification supports precision-enough closed-loop amplification when resistor matching and calibration are considered. The 5.5 V ceiling allows operation from regulated 3.3 V or 5 V rails common in industrial control, instrumentation, sensor-conditioning, and embedded systems. Because the IC contains four amplifiers, each channel has independent input, output, and power connections arranged according to the manufacturer pin-description table. Typical applications include voltage buffers, transimpedance stages, active filters, differential amplifiers, level shifting, and low-frequency audio paths. Decoupling capacitors near the supply pins help control impedance and prevent supply noise from appearing at the amplifier output. A key design consideration is that the gain-bandwidth product must be appropriate for the operating frequency. A closed-loop gain of 10 leaves approximately 100 kHz of bandwidth, so higher closed-loop gains reduce usable bandwidth. The offset specification alone does not determine total accuracy; input bias current, input common-mode range, output swing, resistor tolerance, and temperature drift also contribute to the final error budget. This page organizes the device specifications, package information, design guidance, and engineering selection criteria into a compact reference. It also highlights where additional datasheet details are required before a circuit is released for production.
LM324M - Low-Power Quad Op Amp | Texas Instruments
The Texas Instruments LM324M is a low-power, general-purpose quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin SOIC package. The verified source identifies the device as a standard four-circuit amplifier designed for operation from a single power supply over a wide voltage range. Because exact electrical ratings were not included in the supplied source data, values such as supply voltage, gain-bandwidth product, input bias current, and output-current limits remain subject to confirmation in the manufacturer datasheet. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two inputs. Negative feedback establishes a stable closed-loop gain and bandwidth. The LM324 family belongs to the broader quad-operational-amplifier hierarchy: operational amplifier, analog amplifier, linear amplifier, and integrated circuit. Its four internally compensated channels can amplify AC or DC signals when supported by suitable biasing, decoupling, feedback, and output-loading conditions. The principal feature of LM324M is integration. Four amplifiers in one 14-pin SOIC reduce package count and simplify common dual-rail or single-supply analog boards. Internal frequency compensation means each channel does not require a separate compensation network for ordinary closed-loop operation. The verified manufacturer result specifically describes LM324 as low-power and optimized for single-supply operation, while the distributor result classifies LM324M as a standard general-purpose instrumentation and buffer amplifier. The four channels are intended for independent signal-conditioning tasks. Typical functions include noninverting and inverting amplification, voltage buffering, active filtering, cross-coupled analog networks, and sensor-signal conditioning. Internal compensation supports unity-gain buffer use, but stability, output swing, input common-mode range, slew rate, noise, and usable bandwidth must be checked against the actual circuit. A low-power general-purpose amplifier may not be suitable when very wide bandwidth, very low offset, low noise, rail-to-rail input/output, or high capacitive-drive capability is required. A practical single-supply design must establish a suitable input common-mode voltage and output bias point. Bypass the power pin close to the IC, route traces to avoid feedback around unintended paths, and avoid excessive capacitive loading on an output. Because the provided search result does not include verified temperature, RoHS, REACH, or package-dimension details, those specifications should be taken from the official LM324 documentation before release to production. Typical uses include low-frequency sensor conditioning, buffered instrumentation, active filters, classroom electronics, industrial control blocks, and general analog signal chains. This page summarizes the verified product identity and package, provides practical design guidance, distinguishes confirmed facts from missing ratings, and directs buyers to the official product page for complete electrical and qualification data.
LM324M/NOPB - Quad 32V 1MHz Op Amp | Texas Instruments
The Texas Instruments LM324M/NOPB is a four-circuit, general-purpose operational amplifier designed for single-supply operation, with a nominal 32 V maximum supply rating, 1 MHz gain-bandwidth product, and a 14-pin SOIC package. The device combines four amplifiers in one package and is intended for conventional low-cost analog signal-conditioning applications. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose high open-loop gain enables closed-loop functions such as buffering, amplification, summing, comparison, filtering, and differential signal conversion. The LM324 belongs to the broader operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its four-amplifier configuration reduces package count and board area when several independent amplifier stages are required in the same circuit. The LM324M/NOPB is identified by Texas Instruments as a low-power quad operational amplifier. Its four amplifier circuits provide a 1 MHz gain-bandwidth product, while the 32 V supply rating supports higher-voltage industrial and instrumentation systems than typical low-voltage rail-to-rail amplifiers. The 14-pin SOIC (D) package is a conventional surface-mount package, and the specified 0 °C to 70 °C temperature range targets commercial operating conditions. The LM324 family is designed to operate from either a single supply or split supplies. Internal frequency compensation allows stable operation in common noninverting, inverting, voltage-follower, summing, and amplifier configurations without an external compensation network. Its general-purpose architecture is appropriate for transducer amplifiers, DC gain blocks, sensors, audio circuitry, and conventional control loops where moderate bandwidth and broad supply flexibility are more important than rail-to-rail input or output operation. Typical applications include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, current-loop interfaces, instrumentation buffers, and general-purpose analog boards. Because all four channels share one package, decoupling requirements and ground-return design should be evaluated for the complete circuit rather than for each amplifier independently. When laying out a board, place power and ground connections to minimize loop area and avoid routing sensitive input traces close to high-current outputs. The SOIC footprint leaves more separation between pins than a compact leadless package, which can simplify prototype assembly, inspection, and rework. Confirm the exact circuit limits, output-swing behavior, input common-mode range, and stability requirements against the manufacturer datasheet for the intended supply voltage and load. This product record combines the manufacturer’s 32 V, 1 MHz, 14-SOIC and 0 °C to 70 °C identification with same-package alternatives, application guidance, design notes, and a parameter-oriented comparison for engineers evaluating quad general-purpose op amps in SOIC-14 designs.
LM324MT - Low-Power Quad Op Amp, 14-TSSOP | Texas Instruments
Texas Instruments LM324MT is a low-power quad operational amplifier designed for single-supply operation across a wide voltage range. The device integrates four amplifier channels in a 14-pin TSSOP package, and the listed temperature range is 0°C to 70°C. Its quad-channel configuration reduces the number of amplifiers and packages required in designs that need multiple independent analog signal paths. An operational amplifier is a voltage-gain device used to amplify, buffer, filter, or compare analog signals. A quad operational amplifier contains four amplifiers in one integrated circuit. Within the signal-chain hierarchy, an operational amplifier belongs to the amplifier-IC family and, more broadly, to analog and mixed-signal semiconductor devices. The LM324MT is designed for applications operating from a single power supply, which simplifies circuit design in systems without a negative supply rail. The LM324MT provides four amplifier sections in one 14-TSSOP package. Its low-power operating concept is useful when four analog channels are required in compact equipment. The 0°C to 70°C rating identifies it as a commercial-temperature device, so system designers should verify that the enclosure temperature remains within this range. The manufacturer identifies the LM324 as a low-power quad operational amplifier intended for single power-supply operation. Compared with discrete single amplifier packages, integrating four amplifiers into one TSSOP-14 package can simplify assembly and conserve board area. Designers should still account for shared supply pins, input bias currents, output-current limits, input common-mode range, output swing, stability with the selected load, and the behavior of unused amplifier channels. These operating limits must be confirmed against the manufacturer datasheet for the selected electrical grade and package. Typical uses include four-channel sensor conditioning, buffered analog measurement, low-frequency active filtering, voltage comparison, general-purpose signal amplification, and educational or laboratory analog circuits. The single-supply architecture is particularly useful in battery-powered and compact embedded systems where a negative rail is unavailable. Input and output signal ranges must remain within the limits required by the circuit. Layout should place input components close to the associated amplifier pins and maintain short feedback paths. Bypass the supply pins with a suitable local decoupling network, keep sensitive inputs away from switching nodes and high-current return paths, and account for the thermal limits of the TSSOP package. Unused amplifier inputs should be connected to a defined common-mode potential rather than left floating. This product page combines the manufacturer product information, distributor package identification, cross-reference results, application guidance, and a practical comparison of same-package LM324-family choices. It is designed to help engineers evaluate the LM324MT for signal-conditioning and general analog applications while making package and sourcing requirements explicit.
LM324MT/NOPB - Quad 32V 1MHz Op Amp | Texas Instruments
Texas Instruments LM324MT/NOPB is a low-power, quad operational amplifier with four amplifier circuits, a 32 V maximum supply rating, and 1 MHz gain-bandwidth performance in a 14-pin TSSOP package. The device is designed for general-purpose signal conditioning and operates from a single power supply over a wide voltage range. An operational amplifier, or op amp, is an analog signal-processing semiconductor that amplifies the difference between two input voltages. The LM324 belongs to the voltage-feedback operational-amplifier family within the broader amplifier IC and analog semiconductor hierarchy. Its four integrated amplifiers can handle independent channels or be interconnected for filtering, gain, buffering, comparison, and transducer-conditioning functions. The quad configuration consolidates four amplifiers into one device, reducing board area and simplifying multi-channel designs. Key characteristics include a 32 V supply rating, 1 MHz gain-bandwidth product, internally frequency compensation, high voltage gain, and bipolar input and output stages. The manufacturer identifies the LM324 as a standard general-purpose amplifier intended for single-supply operation across a wide voltage range. Internally, each channel uses a voltage-feedback architecture and internal frequency compensation, allowing operation without external compensation components. The four amplifiers share common supply and ground connections, so applications must keep return-current paths short and account for shared thermal behavior when all four channels operate at high output current. The 14-pin TSSOP outline supports compact surface-mount assembly. Typical applications include industrial sensor conditioning, low-frequency audio paths, control-signal buffers, current-to-voltage conversion with external resistors, active filtering, and four-channel instrumentation. The 32 V supply capability is particularly useful in industrial systems where signal levels can exceed conventional low-voltage analog ranges. When laying out a design, place each amplifier's input and feedback components close to the corresponding pins, keep ground returns short, and use a stable bypass capacitor near the supply pins. Account for input common-mode limits, output swing, load capability, and input bias-current errors when setting gain. Stable operation should also be checked across temperature, supply tolerance, and output-current variation. This page combines the exact LM324MT/NOPB package and temperature information with practical design guidance, pin mapping, sourcing information, and qualified same-footprint alternatives. It is intended to help engineers evaluate the device for compact four-channel analog designs without overlooking the electrical limits of the LM324 architecture.
LM324MTX - Quad Op-Amp, 1MHz, 32V, TSSOP-14 | Texas Instruments
The Texas Instruments LM324MTX is a low-power quad operational amplifier containing four independent, high-gain, internally frequency-compensated op amps in a 14-pin TSSOP surface-mount package. It operates from a single supply over a wide voltage range up to 32V total (or +/-16V split supplies) and provides a 1 MHz gain-bandwidth product, making it one of the most widely deployed general-purpose amplifiers in industrial electronics. A general-purpose operational amplifier is a differential voltage amplifier with very high open-loop gain that, with external feedback networks, performs amplification, buffering, filtering, comparison and level-shifting functions. The op amp sits near the top of the analog signal-chain hierarchy: operational amplifier -> amplifier IC -> analog mixed-signal IC -> power management and signal conditioning system. Quad devices such as the LM324 integrate four of these amplifiers on a single die, cutting board area and BOM count in multi-channel analog designs. Key differentiating features include single-supply operation from 3V up to 32V with rail-to-rail-referenced inputs and output that swings close to ground, four independently functioning amplifiers that stay matched and thermally coupled, and very low quiescent supply current draw that is largely independent of supply magnitude. Common-mode input range extends to ground, which is the defining advantage over older op amps in single-supply designs. Internally, the LM324 uses compensated bipolar circuitry that guarantees stability at unity gain without external compensation components. Because all four amplifiers share one bias network, supply current rises only modestly as channels are exercised, and inter-channel thermal drift is minimized in DC-coupled multi-stage circuits. Typical applications include transducer signal conditioning and sensor front ends, active RC filters and multichannel summing amplifiers, industrial PLC analog input stages, battery-powered portable instrumentation, and DC servo or motor-control loop error amplification where four gain stages are needed on one rail. Design-wise, remember the output stage is not rail-to-rail: the high-side output saturates roughly 1.5V below VCC under load, so gain stages needing output swing near the positive rail require headroom or a newer RRIO alternative. The LM324MTX TSSOP-14 footprint is pin-identical across the LM124/LM224/LM324/LM2902 temperature-grade family. This page consolidates drop-in alternatives, per-parameter comparison against automotive and military grade variants, practical design notes, and pricing evidence in one place - information not compiled in the manufacturer datasheet alone.
LM324MTX/NOPB - Quad 1 MHz Op Amp | Texas Instruments
Texas Instruments LM324MTX/NOPB is a low-power, general-purpose quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin TSSOP package. The device supports a single-supply operating range of 3 V to 32 V and provides a gain-bandwidth product of 1 MHz with a slew rate of 0.3 V/µs. Each amplifier can source up to 40 mA, making this device suitable for general signal-conditioning and low-to-moderate-frequency analog systems. An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare analog signals. The LM324 family belongs to the operational-amplifier hierarchy within analog ICs and analog signal-chain components. Its internal frequency compensation removes the need for external compensation networks in conventional closed-loop gain configurations, simplifying implementation in general-purpose amplifier boards. The quad configuration provides four amplifiers in one package, reducing PCB area and component count in designs requiring multiple analog channels. Key electrical characteristics include 1 MHz gain-bandwidth product, 0.3 V/µs slew rate, 20 nA input bias current, and 1 mV input offset voltage. The output stage can supply up to 40 mA per channel, while the low-power architecture supports portable and single-supply systems operating from 3 V to 32 V. Internal frequency compensation makes the amplifier suitable for voltage gains near unity without external compensation capacitors. The 1 MHz bandwidth places the device in the general-purpose, low-to-moderate-frequency class rather than the precision or high-speed class. Designers should account for finite bandwidth and slew rate when processing larger or faster signals, and should verify output swing against the selected supply voltage before driving a load. Typical uses include four-channel sensor conditioning, low-frequency active filters, general-purpose signal buffers, differential-to-single-ended conversion, and instrumentation interfaces. The four independent channels can also be configured as two differential amplifiers when signal polarity relationships require it. The 14-TSSOP package is appropriate for compact surface-mount assemblies, although its narrow lead pitch requires careful PCB layout and inspection. For reliable layout, route input and feedback connections away from switching nodes and high-current return paths. Place input-biasing resistors close to the amplifier inputs to reduce leakage sensitivity, and use short feedback traces to minimize parasitic capacitance. Because this is a general-purpose amplifier rather than a rail-to-rail precision device, input common-mode range and output swing must be checked in the actual supply configuration. This page combines the LM324MTX/NOPB electrical characteristics, package information, drop-in alternatives, comparison data, and practical PCB guidance to support faster component selection and implementation. Use the manufacturer pin-description table and recommended operating conditions when assigning PCB tracks and validating signal headroom.
LM324MWA - Quad 1.2MHz Op Amp | Texas Instruments
The Texas Instruments LM324MWA is a low-power, four-amplifier general-purpose operational-amplifier die designed for single-supply operation over a wide voltage range. Each of its four independent channels combines high voltage gain with internal frequency compensation, and the device is identified as a 1.2 MHz amplifier in the manufacturer product information. LM324MWA is supplied as an unpackaged wafer rather than a leaded or surface-mount package. An operational amplifier is an analog signal-processing IC that compares voltages applied to its high- and low-impedance input terminals and amplifies the difference between them. The LM324 belongs to the operational-amplifier hierarchy, where it is a low-power, general-purpose quad amplifier intended for inexpensive, broadly applicable analog circuits. Four independent channels on one die allow a designer to implement four amplifier functions without using four separate packages. The defining feature of LM324MWA is its combination of four channels, internal frequency compensation, and single-supply operation. Because compensation is integrated into each amplifier, external compensation components are not required for the device's normal operation. Its 1.2 MHz gain-bandwidth figure identifies it as a general-purpose, moderate-bandwidth amplifier rather than a high-speed precision device. The wide supply-voltage range specified for the LM324 family supports use across systems whose rail voltage may vary. The MWA suffix denotes a wafer-sale configuration, so the delivered item is bare semiconductor die instead of a finished, pin-encapsulated IC. Its terminal form and package code are therefore not equivalent to a conventional DIP or surface-mount package. This form can be useful to specialized manufacturers that perform die inspection, wafer-level processing, custom packaging, or multi-die module assembly. It is not intended for direct soldering onto a conventional printed circuit board without an appropriate assembly process. Typical uses for the LM324 family include low-frequency signal conditioning, transducers, sensor interfaces, audio and control circuits, and general instrumentation. Four independent sections can handle several small-signal functions within one device, reducing component count when a system does not require the low noise, high speed, or precision associated with more specialized amplifiers. System designers must also account for the limitations inherent in a general-purpose internally compensated amplifier. The primary design consideration is that wafer supply requires a defined die-handling and packaging strategy. Pin assignment, bonding, inspection criteria, and long-term reliability requirements should be confirmed with Texas Instruments before volume assembly. If the application requires a directly mountable component with established outlines, lead pitch, and thermal behavior, a packaged LM324 orderable part is generally easier to integrate and qualify. This page combines the manufacturer product description, distributor package information, and the supplied cross-reference results with application guidance specific to an unpackaged quad op-amp die. It also distinguishes the wafer-sale format from conventional LM324 package variants and documents which engineering facts require confirmation before custom manufacturing.
LM324MX - Low Power Quad Op Amp, 3V-32V, 14-SOIC | Texas Instruments
The Texas Instruments LM324MX is a low power, general-purpose quad operational amplifier with four independent amplifiers in a 14-pin SOIC package. It operates from 3 V to 32 V single supply or up to plus or minus 16 V dual supply, delivering a large DC voltage gain of 100 dB with 7 mV input offset voltage and 65 dB minimum common mode rejection ratio. An operational amplifier (op amp) is an analog building block that amplifies the difference between two input voltages. The LM324 belongs to the hierarchy of single-supply general-purpose amplifier -> quad operational amplifier -> analog signal conditioning IC -> semiconductor. Internally frequency compensated for unity gain, it needs no external compensation network, which is why it remains the default amplifier for cost-sensitive DC and low-frequency signal conditioning designs. Key characteristics include four amplifiers sharing one supply pin, a wide 3 V to 32 V rail range, single-supply operation from 2 V output swing above ground, and low quiescent current typical of the low-power family. Because all four channels are in one package, a complete amplifier subsystem costs one PCB footprint instead of four, and channels share a common ground reference, which simplifies layout and reduces ground-bounce risk in multi-channel analog circuits. The device is internally trimmed and thermally stable, with input stages protected against differential overvoltage through internal clamp diodes. Because the amplifier is a bipolar-input design rather than a CMOS-input design, input bias current is in the nanoamp range and common mode rejection is good over the full supply range, at the cost of higher supply current than CMOS-input amplifiers. Typical applications include sensor signal conditioning, low-frequency active filters, transducer amplifiers, audio preamplifier stages, current-to-voltage conversion in instrumentation, and general DC gain stages in industrial control and consumer equipment. Because the LM324 family is available from several manufacturers, the same 14-SOIC footprint and pinout are widely supported for second sourcing. When designing around the LM324MX, keep input and output signals inside the common mode range and account for input offset and bias current when working with high-impedance sources. Place the bypass capacitor close to the supply pin and keep feedback loops short so that the modest gain-bandwidth product does not limit stability.
LM324MX/J7001601 - Quad Op Amp | Texas Instruments
The Texas Instruments LM324MX/J7001601 is a low-power, general-purpose quad operational amplifier packaged in a 14-SOIC package with a stated body width of 0.154 inches, or 3.90 mm. The device integrates four operational amplifiers into one package, allowing a design to use four independent amplifier sections without requiring four separate single-amplifier packages. The LM324MX/J7001601 designation is associated with the National Semiconductor LM324MX family and is offered in the market as a 14-pin SOIC device. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. A quad operational amplifier contains four such amplifier sections, making it useful in systems that need several signal-conditioning functions at the same time. Its place in the electronics hierarchy is analog integrated circuit > operational amplifier > quad operational amplifier, and it is commonly used as a building block for sensing, buffering, filtering, amplification, and control circuits. The principal product characteristics established for this ordering code are its four-amplifier configuration, low-power general-purpose design, 14-SOIC package, and commercial operating-temperature designation of 0 to 70 degrees Celsius. The 14-SOIC format supports conventional surface-mount PCB assembly while providing enough pins for four amplifier inputs, four outputs, power rails, and ground connections. A single package can therefore reduce component count and simplify board-level purchasing and assembly. The LM324 family architecture is intended for practical analog signal paths rather than high-speed precision applications. Engineers should use the manufacturer datasheet to confirm input common-mode range, output swing, supply range, offset voltage, input bias current, slew rate, open-loop response, and output-current limitations before fixing a design. Those operating limits determine whether an application requires external bias compensation, output buffering, rail-to-rail signal coverage, or protection from input or output overvoltage. Typical uses include four-channel sensing interfaces, buffered sensor outputs, active low-pass filters, sample-and-hold signal conditioning, current-loop instrumentation, analog control loops, and general-purpose amplifier boards. In each case, the four sections can process related or independent channels while sharing one package. The device can be particularly useful when the design needs more amplifier channels than a dual package provides but does not require the density of a higher-performance mixed-signal component. For layout, keep input and feedback components close to their associated amplifier pins, route high-impedance signals with minimal leakage risk, and place input-biasing resistors where they can minimize leakage and parasitic capacitance. Confirm the polarity of feedback networks for each amplifier section because an incorrect connection can introduce unintended positive feedback and saturation. Decoupling capacitors should be placed at the power pins, and unused amplifier sections should be configured according to the manufacturer recommendations rather than left open. This product summary combines package information, manufacturer documentation locations, practical application guidance, and same-family replacement analysis. It is intended to help engineers determine whether the 14-SOIC quad operational amplifier fits a legacy or new analog board before consulting the complete LM324 datasheet for electrical limits, test conditions, and ordering details.
LM324MX/NOPB - Quad 14-SOIC General-Purpose Amplifier | TI
The Texas Instruments LM324MX/NOPB is a low-power, general-purpose quad operational amplifier packaged in a 14-pin SOIC. It integrates four amplifier channels in one package, making it a practical choice for analog signal conditioning, current-to-voltage conversion, feedback networks, and low-frequency control applications. The device is identified as a Standard (General Purpose) Amplifier with a 4-circuit configuration. An operational amplifier is an analog building block that compares two input voltages and drives its output toward a higher or lower level. The quad LM324MX/NOPB combines four amplifiers in a single 14-pin SOIC, reducing component count and board area compared with four separate single or dual amplifier packages. Its standard general-purpose classification makes it suitable for designs where cost, supply availability, and straightforward implementation matter. The principal documented characteristics are the four-channel architecture, the 14-SOIC package, and the 0°C to 70°C commercial-temperature range associated with the Texas Instruments LM324MX family. The /NOPB suffix identifies the standard ordering variant without the NOPB marking used by some other catalog entries. Its low-power architecture suits battery-operated instrumentation, educational electronics, sensor interfaces, and general-purpose analog boards. In voltage-follower and non-inverting configurations, each amplifier can buffer a sensor output without introducing significant loading. The same buffer function applies to current-to-voltage converters when a sense resistor converts an input current into a measurable voltage. Because all four channels share one package, unused amplifiers can be configured as voltage followers or left unconnected only when their inputs are maintained at valid common-mode voltages. Typical uses include 4-to-20 mA receiver front ends, analog sensor conditioning, low-cost laboratory instruments, audio preamplifier stages, and general DC gain blocks. The quad arrangement is particularly effective when a board needs several similar channels, such as four sensor inputs, four buffered outputs, or a multichannel measurement interface. Designers should confirm the full electrical limits, input common-mode range, output swing, input bias current, gain-bandwidth behavior, and supply-current budget in the manufacturer datasheet before release. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased within the valid input range rather than left floating. This page combines package details, source-based specifications, drop-in alternatives, and practical design guidance for faster component selection.