بەرهەمەکان (3,200+)

MPY100AG - 4-Quadrant Analog Multiplier/Divider | Texas Instruments
MPY100AG

MPY100AG - 4-Quadrant Analog Multiplier/Divider | Texas Instruments

The Texas Instruments MPY100AG is a precision 4-quadrant analog multiplier/divider originally developed by Burr-Brown, delivered in a 14-pin ceramic CDIP (0.300 inch, 7.62 mm) package and operating from dual supplies of 8.5 V to 20 V (typically +/-15 V DC). An analog multiplier is a linear function block whose output voltage is proportional to the product of two input voltages; the broader family of multipliers/dividers sits within the analog signal processing hierarchy, below full analog computers but above simple operational amplifier circuits. The MPY100 integrates a complete multiplication cell, output amplifier, and laser-trimmed thin-film resistor network on a single monolithic die, eliminating the external trims and potentiometers required by older discrete multiplier designs. Key features include true four-quadrant multiplication, on-chip support for analog division and square-root computation without external amplifiers, a slew rate of 20 V/us, and guaranteed accuracy classes achieved through laser trimming. The ceramic DIP package supports extended temperature deployment and provides the mechanical robustness expected in instrumentation and military-grade builds. The transfer architecture of the MPY100 implements W = XY/10 (multiplication) or W = 10Z/X (division) and W = square-root of (10Z) (square-root) via simple pin strapping, with fully differential, high-impedance inputs derived from the internal op amp. Laser trimming of the one-chip design guarantees accuracy over temperature, which is the core advantage over untrimmed GA (general purpose analog) multipliers such as the classic MC1495 class of parts that require extensive external calibration. Typical applications include analog computation blocks in process control, RMS-to-DC and power measurement front ends, voltage-controlled filters and amplifiers, modulators/demodulators and phase detectors, and square-root extraction from differential pressure sensors for flow measurement. When designing with the MPY100AG, use symmetric +/-15 V rails, keep feedback paths short, and reserve headroom: the 10 V full-scale input and output architecture means signals should be scaled to stay within the guaranteed accuracy window rather than the absolute supply limits. This page adds value beyond the TI datasheet by consolidating drop-in same-family alternatives (MPY100CG, MPY100SG), grade-level selection guidance, practical design notes, and RFQ-based sourcing information in one engineer-oriented reference.

RFQ پەیوەندی
MPY100AM - Precision Analog Multiplier/Divider | Texas Instruments
MPY100AM

MPY100AM - Precision Analog Multiplier/Divider | Texas Instruments

The Texas Instruments MPY100AM (originally Burr-Brown) is a precision analog multiplier/divider IC in a 10-pin TO-100 metal can package, offering four-quadrant multiplication, analog division, and square-root functions in a single laser-trimmed monolithic chip requiring no external trimming potentiometers. An analog multiplier/divider is a nonlinear signal-processing building block that produces an output proportional to the product, quotient, or square root of two input voltages. Within the signal-chain hierarchy, it sits alongside operational amplifiers and precision analog computing circuits, and is classified as a high-performance analog IC used for modulation, demodulation, rms conversion, and power measurement. Key features per the manufacturer datasheet include low cost, differential inputs, 100% tested and guaranteed accuracy, no external trimming required, low noise performance (quoted at 10 kHz in the datasheet features), and a highly reliable one-chip design. Because the transfer function is laser-trimmed at the factory, designers avoid the tedious calibration procedures associated with discrete multiplier cells built from op-amps and matched transistor pairs. The MPY100 architecture integrates the multiplier core and output summing amplifier on one die, which improves accuracy and thermal tracking compared to hybrid or multi-chip solutions. It performs four-quadrant multiplication, division, and square rooting without external amplifiers or potentiometers, simplifying PCB area and bill-of-material cost in analog computation circuits. Typical applications include analog signal conditioning, modulation and demodulation, RMS-to-DC conversion front ends, power calculation in instrumentation, and general-purpose analog computing in industrial and test equipment. The wide operating temperature range supports demanding industrial environments. Design consideration: as an analog computation device, the MPY100 is sensitive to supply decoupling and layout; keep input traces short and ground the differential inputs properly to preserve the factory-trimmed accuracy. This page synthesizes distributor availability, family alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
MPY100BG - 4-Quadrant Analog Multiplier/Divider | Texas Instruments
MPY100BG

MPY100BG - 4-Quadrant Analog Multiplier/Divider | Texas Instruments

The Texas Instruments MPY100BG is a 4-quadrant analog multiplier/divider, a low-cost precision computational component originally designed by Burr-Brown and supplied in a 14-pin ceramic DIP (CDIP) package. It performs four-quadrant multiplication, analog division, and square-root operations on-chip, executing the transfer function W = (X1 - X2)(Y1 - Y2)/10 without external amplifiers, trimming potentiometers, or support circuitry. An analog multiplier is a nonlinear signal-processing IC whose output voltage is proportional to the product of two input voltages, placing it in the broader family of analog computational circuits alongside operational amplifiers, log/antilog amplifiers, and voltage-to-frequency converters. The MPY100 belongs to the class of precision multipliers used for real-time signal math in analog signal chains before or alongside digital processing. Key features of the MPY100BG include differential X and Y inputs for common-mode noise rejection, 100% factory testing with guaranteed accuracy grades, laser-trimmed one-chip construction that eliminates external trimming, low output noise up to 10 kHz, and wide-temperature operation. According to the manufacturer datasheet, the family emphasizes low cost, high reliability, and guaranteed accuracy specifications. Technically, the MPY100 uses a laser-trimmed monolithic design: thin-film resistors and the gain-setting element are trimmed at wafer level, so transfer-function accuracy is guaranteed without user calibration. This distinguishes it from older multiplier generations such as the discrete-trimmed MC1495-class parts, which required external offset and scale-factor potentiometers. The internal output amplifier buffers the product signal, allowing direct connection to loads or further analog stages. Typical applications include analog signal multiplication and division in instrumentation, modulation and demodulation (AM, suppressed-carrier) in communications equipment, RMS-to-DC and square-root computation in measurement systems, function generation, and power/voltage-product measurement in energy monitoring circuits. The ceramic package suits industrial environments requiring long-term stability. When designing with the MPY100BG, observe the datasheet supply-voltage and input common-mode limits, and keep unused inputs properly terminated; division and square-root configurations require specific feedback wiring of the output amplifier as shown in the manufacturer datasheet application circuits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
MPY100BM - Precision Multiplier/Divider TO-100 | Texas Instruments
MPY100BM

MPY100BM - Precision Multiplier/Divider TO-100 | Texas Instruments

The Texas Instruments MPY100BM (originally Burr-Brown) is a precision analog multiplier-divider IC delivering four-quadrant multiplication, division, and square-root functions in a 10-pin TO-100 metal can package, operating from nominal +/-15V supplies with a bipolar process design and a nominal bandwidth of 0.55 kHz as listed by distributor parametric data. An analog multiplier-divider is a nonlinear signal-processing device that produces an output proportional to the product, quotient, or square root of two input voltages. Within the analog signal chain hierarchy, it sits alongside operational amplifiers and instrumentation amplifiers as a foundational analog computational block, enabling power measurement, RMS conversion, modulation, and gain-control functions without digital conversion. The MPY100 integrates the multiplier core and output summing amplifier on a single laser-trimmed die. Key features include differential X and Y inputs, 100% factory accuracy testing with guaranteed specifications, no external trimming components required, low noise at 10 kHz, and a highly reliable one-chip design. These characteristics eliminate costly potentiometer trimming in production and simplify board-level design. Technically, the MPY100 employs a laser-trimmed bipolar translinear multiplier core followed by an on-chip output amplifier, allowing direct configuration as a multiplier, divider (using the Z input feedback path), or square-rooter with only external connections, no external active parts. Burr-Brown's laser trimming establishes the rated total error grade at the factory over the full temperature range for the M grade. Typical applications include analog signal computation in industrial instrumentation, power and energy measurement, modulator-demodulator (analog communication) circuits, and RMS-to-DC conversion front ends where a compact, trimmed computational element is preferred. A key design consideration: the 10-pin TO-100 metal can is a through-hole package with round pin arrangement, so verify board footprint and thermal-mechanical anchoring before layout, and observe supply headroom for the input signal range. This page synthesizes distributor pricing, drop-in alternatives, design notes, and application guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
MPY100SM - Precision Analog Multiplier/Divider | Texas Instruments
MPY100SM

MPY100SM - Precision Analog Multiplier/Divider | Texas Instruments

The Texas Instruments MPY100SM is a laser-trimmed, precision four-quadrant analog multiplier/divider housed in a 10-pin TO-100 metal can package. Originally introduced by Burr-Brown (acquired by Texas Instruments in 2000), the MPY100SM performs multiplication, division, and square-root operations on-chip with guaranteed accuracy and no external trimming required. An analog multiplier is a device whose output voltage is proportional to the product of two input voltages. It sits within the broader analog signal processing hierarchy: analog multiplier/divider -> nonlinear analog function circuit -> operational amplifier family -> analog front-end signal chain components. The MPY100 belongs to the class of general-purpose multiplier/dividers used wherever two analog signals must be algebraically combined in real time, before digital conversion became the default approach. Key features include differential X and Y inputs, a fully 100% tested and guaranteed accuracy specification, laser-trimmed on-chip thin-film resistors that eliminate external potentiometers, and low noise performance specified at 10 kHz. The single-chip design delivers high reliability, and the device operates over a wide temperature range with standard +/-15V supplies, making it suitable for industrial environments. Technically, the MPY100 integrates a Gilbert-cell style translinear multiplier core with an internal output amplifier, so squaring, square-rooting, and ratio computations need no external op-amps or trim networks. The transfer function is set entirely by the on-chip laser-trimmed network, which is the source of its guaranteed, factory-tested accuracy - a notable advantage over older hybrid multipliers requiring calibration. Typical applications include analog computation in instrumentation, modulation and demodulation in communications systems, true-RMS and power measurement circuits, voltage-controlled filters and amplifiers, and square-root extraction from 4-20 mA transducer signals. Design consideration: the MPY100 is a legacy part - Texas Instruments recommends the MPY634 as the modern replacement, so new designs should evaluate it while the MPY100SM serves existing boards and last-time-buy programs. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
MS32011 - Component Datasheet, Specs & Alternatives
MS32011

MS32011 - Component Datasheet, Specs & Alternatives

The MS32011 component data sheet and specification profile, drawn from manufacturer and distributor sources, is summarized below for engineering reference. The MS32011 appears in distributor catalogs and parts databases, but no verified manufacturer datasheet, parametric block, or authoritative specification table was located in the provided web search results. The MPN string is similar to several unrelated catalog numbers - including an MS3201 infrared transceiver from Novalog, an MS320 Schottky barrier diode from Zibo Seno, an MSD3201 by ITT, and an MS3201 Tektronix acquisition module - none of which are confirmed to be the same silicon as the MS32011. Because of this ambiguity, every spec below is marked as needing datasheet verification before it can be cited in a BOM, schematic, or compliance document. This page exists to consolidate every public reference to the string "MS32011" so that an engineer searching for the MPN can quickly see what is known, what is unconfirmed, and where to look next. The Verified Web Data returned a 1:32 plastic scale model kit SKU (Mars Figures Delta Force MS32011), a tapered-roller bearing cross-reference (32011 series), a Phoenix Contact VAL-MS 320/1+1 surge arrester, and generic cross-reference tools - none of which is the MPN itself. No manufacturer page, octopart record, distributor SKU, or octopart-equivalent parametric listing was returned for the exact string "MS32011" as an electronic component. Until the manufacturer and category of the MS32011 are confirmed, treat this entry as a placeholder record. The drop-in alternatives list below is therefore populated with parametrically similar parts from common adjacent families (LDO regulators, op-amps, and small-signal analog ICs) only as engineering search aids; none have been verified as drop-in compatible because the package and pinout of the MS32011 itself are unknown. Use this entry as a starting point for cross-referencing, and confirm all specifications against the original manufacturer datasheet before design-in. Recommended next steps for an engineer working with the MS32011: search the manufacturer prefix on the part label or shipping carton, scan the package marking under magnification, run the MPN through DigiKey/Mouser parametric search, and request a datasheet from the supplier of record. Once the manufacturer and category are identified, the spec list, pinout, package, and alternatives can be updated with verified values. Do not assume any spec in this entry is production-ready without datasheet confirmation.

RFQ پەیوەندی
MS32051 - 4-Ch 25Gb/s CDR+TIA Array Receiver | Macom/Microsemi
MS32051

MS32051 - 4-Ch 25Gb/s CDR+TIA Array Receiver | Macom/Microsemi

The MS32051 is a 4-channel optical array receiver with integrated Clock and Data Recovery (CDR) and Transimpedance Amplifier (TIA), designed for 24Gb/s to 28Gb/s QSFP28-style optical modules. Each of the four channels supports data rates up to 28Gb/s and offers a CDR bypass mode for 10Gb/s non-retimed serial links, enabling mixed-rate QSFP28 deployments. The device is intended for next-generation datacom and telecom line-side optics where high channel density and low power per gigabit are required. A transimpedance amplifier (TIA) is a current-input, voltage-output analog front-end that converts the small photocurrent from a photodiode or ROSA into a differential voltage suitable for high-speed decision circuits. A Clock and Data Recovery (CDR) block then retimes the signal to a clean reference clock, reducing deterministic jitter accumulated across the optical and electrical paths. Combining the TIA and CDR in a single ASIC (the MS32051 belongs to the IC / integrated circuit taxonomy: optical IC -> transceiver IC -> mixed-signal IC -> semiconductor) allows module designers to drop four receive lanes onto one die, cutting BOM count, board area, and power compared with discrete TIA + CDR designs. Key features include integrated 4-channel TIA with typical input-referred noise suitable for ROSA modules, on-die CDR supporting 24-28 Gb/s retimed operation, CDR bypass for legacy 10 Gb/s lanes, per-channel loss-of-signal (LOS) indication, and an I²C / 4-wire digital control interface for setup, monitoring, and rate switching. Differential CML-compatible output drivers deliver sub-UI jitter performance required by IEEE 802.3bm / 100GBASE-SR4 links. Typical applications include QSFP28, QSFP-DD, and CFP-style parallel optical transceivers for data-centre switches, 100G / 400G client-side optics, OTU4 telecom line cards, and breakout 4×10G / 4×25G AOC / AOI assemblies. Placing the MS32051 between the photodiode array and the module's host-side DSP or switch ASIC also reduces clock routing complexity. When designing with the MS32051, treat the high-speed differential outputs as 100-Ω matched pairs and route them on a continuous reference plane; consult the manufacturer datasheet for thermal-coupling and supply-decoupling guidelines. CDR bypass mode must be selected via the digital interface before low-rate traffic is forwarded to avoid false lock to pattern-dependent edges.

RFQ پەیوەندی
NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi
NCS199A1RSQT2G

NCS199A1RSQT2G - Zero-Drift Current Sense Amp, Gain 50 | onsemi

The onsemi NCS199A1RSQT2G is a zero-drift, voltage-output current-shunt monitor (current sense amplifier) with a fixed gain of 50 V/V, supplied in a 6-pin SC-88 / SC-70-6 / SOT-363 surface-mount package. It can sense voltages across a current shunt at common-mode voltages from -0.3 V to 26 V, independent of the device supply voltage, making it suitable for both high-side and low-side current-sensing topologies in industrial, automotive, and consumer systems. The device operates from a single supply of 2.2 V to 26 V, offers rail-to-rail output swing, and delivers typical input offset voltage below 50 uV. A current sense amplifier (CSA) is a type of instrumentation amplifier that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. CSAs belong to the broader family of analog signal-conditioning ICs and are essential building blocks in power management, motor control, and battery-monitoring systems where high common-mode rejection, low offset, and small package size are required. Key features include a fixed gain of 50 V/V (other family members NCS199A2R = 100 V/V, NCS199A3R = 200 V/V/Current = 50 mA), bidirectional sensing capability, 60 uV maximum input offset voltage (zero-drift chopper architecture), and a -3 dB bandwidth of approximately 90 kHz. The zero-drift internal architecture continuously cancels 1/f noise and offset drift over temperature, achieving typical input offset drift of 0.5 uV/C. The NCS199A1R uses a proprietary auto-zero / chopper-stabilized topology that eliminates the need for external precision resistors and provides excellent long-term stability. Common-mode rejection ratio (CMRR) exceeds 100 dB at DC, and the small SOT-363 footprint allows placement directly at the shunt resistor for minimum parasitic errors. The part also includes an internal EMI filter and ESD protection rated at 4 kV HBM. Typical applications include battery-pack current monitoring in power tools and e-bikes, motor-control current loops in BLDC drivers, solar MPPT input current sensing, server and telecom -48 V hot-swap current monitoring, and USB-C PD current telemetry. In all cases the wide -0.3 V to 26 V common-mode range allows the same IC to be used on either rail of the load. When designing with this part, keep the input differential loop to the shunt as short as possible and place a 10 nF differential capacitor across the IN+ and IN- pins to suppress switching noise from PWM-driven loads. Ensure the output does not drive more than 1 nF of capacitance without a series isolation resistor to maintain stability.

RFQ پەیوەندی
NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi
NCV2202SN2T1G

NCV2202SN2T1G - 0.85V CMOS Comparator, Open-Drain, SOT-23-5 | onsemi

The onsemi NCV2202SN2T1G is a sub-one-volt, low-power, single-channel CMOS comparator in a 5-pin SOT-23 (TSOP) package, qualified to the AEC-Q100 automotive standard. It operates over a supply voltage range of 0.85V to 6.0V, consumes only 10 uA of quiescent current, and provides an open-drain output capable of rail-to-rail input and rail-to-rail output swing. The NCV2202 prefix indicates AEC-Q100 / PPAP-capable automotive grade screening, while the non-automotive NCS2202 family member shares the same die and pinout. What is a low-voltage CMOS comparator? A comparator is an analog circuit that compares two input voltages and produces a binary output indicating which input is larger. Low-voltage CMOS comparators like the NCS2200/NCV2202 series are designed to operate from supply rails below 1V, making them essential building blocks in single-cell battery powered electronics where earlier bipolar comparators could not function. They are widely used for voltage threshold detection, battery monitoring, and system reset generation in portable, IoT, and automotive sensor systems. The NCV2202SN2T1G features a propagation delay of approximately 1 us, an internal hysteresis for clean switching on slow-moving input signals, and an open-drain output stage that allows the user to pull the output up to any rail up to 6V, independent of VDD. The internal design prevents phase reversal on the inputs when the common-mode voltage is driven beyond the supply rails, preserving output integrity in fault conditions. The device is built on a sub-micron CMOS process optimized for ultra-low quiescent current, with 0.3 uA consumption when the enable pin is held low (output tri-state). Two industry-standard pinout options exist across the NCS2200 family: SOT-23-5 and SC-88-5 (SC70-5); the SN2T1G suffix denotes the TSOP / SOT-23-5 package on a 7-inch tape-and-reel. Typical applications include low-battery detection in single-cell Li-ion and alkaline systems, window comparators for voltage monitoring in automotive ECU rails, zero-crossing detectors in motor control, and threshold detectors in IoT sensor nodes. The automotive-grade NCV prefix makes this variant especially suitable for under-the-hood, body, and infotainment ECUs. When designing with the NCV2202SN2T1G, place a pull-up resistor on the open-drain output (typically 10 kohm to 100 kohm) sized according to the desired propagation speed and power budget. Decouple VDD with a 100 nF ceramic capacitor located within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

RFQ پەیوەندی
NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi
NCV2250SN2T3G

NCV2250SN2T3G - 50ns Low-Voltage Rail-to-Rail Comparator | onsemi

The onsemi NCV2250SN2T3G is a single high-speed, low-voltage, rail-to-rail comparator with push-pull output, packaged in a 5-pin TSOP. It delivers a typical propagation delay of 50 ns with a 100 mV input overdrive, making it well suited for fast threshold detection in space-constrained designs. The part operates from a single 1.8 V to 5.5 V range, and the input common-mode range extends 200 mV beyond both supply rails, allowing direct sensing near ground or VCC. The push-pull output stage eliminates the external pull-up resistor required by open-drain alternatives and swings to within millivolts of both rails. A comparator is an analog active device that compares two input voltages and drives its output logic a discrete single (high or low) based on which input is more positive. Within the broader taxonomy, the NCV801A sits under analog comparator -> comparator -> amplifier/comparator IC -> semiconductor. Push-pull CMOS output topology differs from open-drain comparators (such as the classic LM393) by actively driving both high and low states, enabling faster edges and lower power in many applications. This category of comparator is essential in any mixed-signal system requiring fast logic-level translation from analog signals. Key features include 1.8 V to 5.5 V single-supply operation, 200 mV beyond-the-rails input common-mode range, 50 ns typical propagation delay (100 mV overdrive), push-pull CMOS output, low quiescent current, and automotive-grade NCV prefix indicating PPAP-capable qualification per onsemi's automotive quality program. The 5-TSOP package consumes only a few square millimeters of PCB area, ideal for compact sensor and signal-conditioning modules. The NCV2250 is built on a standard CMOS process with on-chip ESD protection diodes on the inputs and outputs. The rail-to-rail input stage uses a complementary differential pair topology that maintains linear behavior across the full common-mode range. Internally, hysteresis can be introduced via external positive feedback resistors to prevent output chattering on slow-moving inputs. The NCV2250SN2T3G is functionally identical to the NCS2250SN2T3G except for automotive-grade qualification and traceability. Typical applications include zero-crossing detectors for line-voltage sensing, battery voltage monitoring in 12 V automotive systems, window comparators with multi-threshold detection, motor control feedback loops, sensor signal conditioning for microcontroller ADC front-ends, and threshold alarms in industrial control. The wide input common-mode range is particularly valuable for current-sense applications where the sense resistor sits at a high common-mode voltage close to the supply rail. When designing with this part, ensure input signals stay within the ESD rating of the device and consider adding small input series resistance to limit fault current during over-voltage transients. Decoupling the supply pin with a 100 nF ceramic capacitor placed within 3 mm of the VCC pin is essential for stable high-frequency switching performance. This page synthesizes distributor inventory, the parametric equivalent on the manufacturer's cross-reference database, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi
NCV2904DR2G

NCV2904DR2G - Dual Op-Amp, 3-26V Single Supply | onsemi

The onsemi NCV2904DR2G is a single-supply dual operational amplifier in an 8-pin SOIC (Case 751) package, operating from 3.0 V to 26 V with a common-mode input range extending to ground/VEE, targeted at automotive-grade applications. An operational amplifier (op-amp) is a high-gain differential voltage amplifier that sits within the analog signal chain hierarchy: op-amp -> amplifier IC -> analog IC -> semiconductor. Dual op-amps integrate two independent amplifier cores in one package, halving board space and BOM line items versus two singles. Single-supply op-amps like the NCV2904 are specifically designed for input common-mode ranges that reach the negative rail, making them usable directly on ground-referenced sensor signals without negative supplies. Key features of the NCV2904 include low power drain, short-circuit protected outputs, a true differential input stage, internally compensated frequency response, and ESD clamps on the inputs. The NCV prefix designates onsemi automotive qualification and temperature screening, making this device suitable for under-hood and body-electronics environments. Per the onsemi datasheet, the LM358 series is equivalent to one-half of an LM324, positioning the NCV2904 as the automotive member of this industry-standard family. Technically, the NCV2904 uses the circuit designs perfected for the quad LM2904/LM324 family: an internally compensated architecture that provides unity-gain stability without external compensation components. Single-supply or split-supply operation gives designers flexibility across 3.0 V to 26 V rails, and the input bias currents are low, minimizing offset errors with high-impedance sensors. Typical applications include automotive sensor signal conditioning (throttle position, pressure), battery-voltage monitoring dividers, comparators for window detection in ECUs, and general industrial signal amplification on single 5 V to 24 V rails. A key design consideration: the output cannot swing to the positive rail, so gain-setting must keep target output levels below the VOH specification at the expected load current. This page synthesizes distributor availability, drop-in alternatives across the LM258/LM358/LM2904 family, and practical design notes beyond what the manufacturer datasheet states.

RFQ پەیوەندی
NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532AD

NE5532AD - Dual 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532AD is a dual, low-noise operational amplifier designed for audio applications, with a 10 MHz typical unity-gain bandwidth, 5 nV/√Hz typical input noise voltage at 1 kHz, and 100 dB typical high dc voltage gain. The device is supplied in an 8-pin SOIC package. It is unity-gain compensated and combines low noise, low distortion, high output-drive capability, and a typical 32 V peak-to-peak output voltage swing under ±18 V supply conditions. An operational amplifier is an active semiconductor device that uses high gain and negative feedback to amplify voltage differences between its inputs. The NE5532 belongs to the low-noise operational amplifier hierarchy, which sits within analog signal-chain ICs, integrated circuits, and semiconductor devices. Its dual-amplifier configuration provides two independent amplifiers in one package, reducing board area in audio preamplifiers, mixers, active filters, and signal-conditioning circuits. The principal audio-oriented characteristics are 5 nV/√Hz typical equivalent input noise voltage at 1 kHz and a 10 MHz typical unity-gain bandwidth. According to the Texas Instruments product description, the NE5532 is a dual 30 V, 10 MHz low-noise operational amplifier. The device also provides 100 dB typical high dc voltage gain, a 32 V typical peak-to-peak output swing with ±18 V supplies, and a typical slew rate of 600 V/µs. The NE5532x family is internally compensated for unity-gain operation, reducing the external compensation components normally required around a high-speed amplifier. Its dual architecture allows two amplifier channels to share one package while retaining the low-noise characteristics sought in audio paths. Input-protection diodes, output short-circuit protection, and a high output-drive capability are identified in the manufacturer datasheet, making the device suitable for conventional low-frequency audio and general analog applications. Typical uses include stereo audio preamplification, mixing consoles, headphone-driver stages, active equalization filters, low-level audio signal conditioning, and instrumentation requiring low input noise. The dual configuration is especially useful where two related channels are required, such as left and right program paths. Its 10 MHz bandwidth also provides more than enough bandwidth for conventional audio while retaining useful response for other precision low-noise signal-chain work. When designing around the NE5532AD, verify the required output swing, input common-mode range, supply voltage, and stability at the selected gain against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet rather than left with open inputs. Source and sink capability should also be checked when driving a transformer, headphone stage, or capacitive load. This product record combines verified manufacturer and distributor information with practical engineering guidance, package and pinout details, pricing references, and a qualification of available drop-in alternatives. The comparison and application sections emphasize where the NE5532AD fits and where the available source evidence does not support claiming a true same-package replacement.

RFQ پەیوەندی
NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi
NE5532AD8

NE5532AD8 - Dual Low Noise Op-Amp, 8-SOIC, 5nV/√Hz | onsemi

The onsemi NE5532AD8 is a dual high-performance, internally-compensated low-noise operational amplifier supplied in an 8-pin SOIC (SO-8, "D8" suffix) surface-mount package. The device integrates two independent op-amp channels with input-protection diodes, output short-circuit protection, very low equivalent input noise voltage of about 5 nV/√Hz typical at 1 kHz, a high unity-gain bandwidth of 10 MHz, a 9 V/µs slew rate, and a 600 Ω drive capability, all from a single dual-supply rail of ±3 V to ±20 V (or single-supply 6 V to 40 V). An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. It is the fundamental analog building block inside audio preamplifiers, active filters, instrumentation stages, servo loops, ADC input buffers, and DAC output I/V converters. The NE5532 family belongs to the "low-noise audio" op-amp class — a category that improves upon generic parts such as the 1458 by combining low voltage noise, wide bandwidth, and strong output drive into one device. Key features include low harmonic distortion (typically 0.002 % at 1 kHz into 600 Ω), high output current that can drive 600 Ω headphone loads directly, large output voltage swing (≈ ±13 V on ±15 V supplies), and excellent channel separation around 110 dB at 1 kHz. The "A" suffix denotes the higher-precision NE5532A variant with tighter input-offset voltage (typically 0.5 mV versus 0.5 mV for the non-A) and improved AC characteristics versus the original NE5532, while remaining pin-compatible with the standard NE5532 socket. Architecturally, the NE5532A uses a bipolar-junction input stage with emitter-degeneration resistors, a PNP common-emitter second stage, and an NPN class-AB output stage. Compensation is built into the die (no external capacitor required), which simplifies PCB design but caps stable unity-gain operation. Designers should treat the device as a "single-supply-unfriendly" part when planning ground-referenced single-rail circuits; a mid-rail bias is required for true ground sensing. Typical applications include high-fidelity audio preamplifiers, mixing consoles, microphone preamps, RIAA phono stages, line drivers, active crossovers, test-instrumentation signal conditioners, and ADC/DAC interface buffers. The 8-pin SOIC footprint is well-suited to high-density PCB designs and is one of the most widely supported DIP-socket IC sockets on adapter boards. When designing with the NE5532AD8, derate output current with increasing junction temperature, mind the input common-mode range that does not include the negative rail, and provide a solid ground pour for the exposed copper pad of the SOIC to keep the junction temperature below 150 °C. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi
NE5532AD8G

NE5532AD8G - Dual 10 MHz Low-Noise Op Amp | onsemi

onsemi NE5532AD8G is a dual, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and two amplifier circuits in an 8-pin SOIC package. It is intended for audio, instrumentation, and control applications where low noise and improved output drive are important. The device is specified for dual supplies of ±3 V to ±20 V and commercial-temperature operation. A dual operational amplifier combines two independent amplifiers in one package. The NE5532A family belongs to the operational-amplifier hierarchy, within analog signal-conditioning and active-control systems. Its internally compensated design simplifies use in non-inverting, inverting, and feedback configurations without an external compensation network, while its low-noise characteristics make it useful when signal integrity must be preserved through amplification. The verified NE5532AD8G data identifies a 10 MHz gain-bandwidth product, 9 V/µs slew rate, 200 nA input-bias current, 500 µV input-offset voltage, 8 mA supply current, and a 3 V to 20 V supply range in the distributor listing. The dual SOIC package provides two circuits in one component, reducing board area compared with separate single amplifiers. Its improved output-drive capability and small-signal bandwidth distinguish it from basic general-purpose dual op amps. Typical uses include stereo audio preamplification, mixer stages, active filters, microphone and line-level signal conditioning, test equipment, and industrial control circuits. In audio designs, the low-noise architecture helps preserve quiet signal paths, while the 9 V/µs slew rate supports higher-frequency transients when the circuit bandwidth and load permit. In instrumentation applications, the two amplifiers can process complementary or sequential channels. The primary design consideration is supply and load compatibility. Confirm the dual-supply range against the system rails, check input and output swing limits for the selected gain, and place decoupling capacitors close to the supply pins. Stable feedback-network layout, adequate output-current capability, and thermal margin should be checked against the actual signal amplitude and frequency. No SOA applies because this is a linear operational amplifier rather than a power semiconductor.

RFQ پەیوەندی
NE5532AD8R2 - Dual 10MHz Low-Noise Op Amp | onsemi
NE5532AD8R2

NE5532AD8R2 - Dual 10MHz Low-Noise Op Amp | onsemi

The onsemi NE5532AD8R2 is an internally compensated, dual low-noise operational amplifier with a 10 MHz gain-bandwidth product, packaged in an 8-pin SOIC. It combines two amplifier channels in one package for audio, instrumentation, and general-purpose signal-processing circuits where low-noise performance and moderate bandwidth are important. The device operates from ±3 V to ±20 V and is specified at 38 mA per channel, with 200 nA of input bias current, 70 dB common-mode rejection ratio, and 1 µA maximum input offset current. An operational amplifier is an analog signal-processing IC that compares its inverting and non-inverting inputs and drives its output to amplify the difference between them. The NE5532 belongs to the internally compensated operational-amplifier family within the broader amplifier, analog IC, and semiconductor hierarchies. Internal compensation makes the amplifier stable without an external compensation network, simplifying conventional audio and instrumentation designs. Its dual-channel configuration reduces component count and board area when two gain stages are required. The NE5532AD8R2 is specifically described as a low-noise dual amplifier. Its 10 MHz gain-bandwidth product supports audio-frequency amplification and general closed-loop signal conditioning, while the 70 dB common-mode rejection helps reject common-mode disturbance on differential inputs. The low 200 nA input bias current can simplify biasing of higher-impedance source networks, although the supplied data does not establish input impedance, input capacitance, slew rate, or output-current capability. Typical uses include stereo audio preamplification, active equalization, low-level microphone-stage amplification, instrumentation buffering, and dual-channel analog filtering. In a preamplifier, the device can be configured as a non-inverting stage with feedback resistors, while the two internal channels can process left and right signal paths independently. In instrumentation circuits, the dual format can support gain and active filtering functions without requiring two separate amplifier packages. Designers should preserve the SOIC-8 footprint and verify the exact channel pin assignments against the manufacturer datasheet before layout release. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels require appropriate input termination rather than being left floating. Input and output swings, gain-bandwidth behavior, stability, and output-current limits must be checked against the circuit operating conditions. This page consolidates the verified onsemi and distributor information, provides package-level selection guidance, and distinguishes electrically similar candidates from confirmed drop-in replacements. Pricing, lifecycle classification, exact pin names, and several detailed electrical parameters remain explicitly marked where the supplied source data does not provide authoritative values.

RFQ پەیوەندی
NE5532AD8R2G - Dual Low-Noise Amplifier | onsemi
NE5532AD8R2G

NE5532AD8R2G - Dual Low-Noise Amplifier | onsemi

The onsemi NE5532AD8R2G is a dual, internally compensated, low-noise operational amplifier rated for 3 V to 20 V supply operation and supplied in an 8-pin SOIC package. It provides two amplifier channels in one package, making the device suitable for professional audio, instrumentation, signal conditioning, active filtering, test and measurement, and general-purpose analog designs. The verified distributor descriptions identify the NE5532AD8R2G as a standard general-purpose amplifier with two circuits and an 8-SOIC package. An operational amplifier is an analog building block that amplifies the voltage difference between its non-inverting and inverting inputs. Internally compensated operational amplifiers include frequency-compensation circuitry that establishes a stable operating characteristic without requiring an external compensation capacitor. Within the broader semiconductor hierarchy, an operational amplifier belongs to the linear-amplifier and signal-conditioning IC family, where low noise, output-current capability, slew rate, and input bias behavior determine its suitability for sensitive analog signals. The NE5532 family is specifically associated with low-noise audio and instrumentation operation. A dual-channel configuration reduces the number of packages required when two amplifier sections are needed, while the 8-pin SOIC format supports conventional surface-mount assembly. The Mouser listing specifies a 3 V to 20 V operating range, and the Arrow listing describes the device as a dual low-noise amplifier with an automotive AEC-Q100 option. These characteristics make the amplifier relevant to signal paths where low-noise performance and adequate output drive are more important than very small package area. The NE5532/SE5532 device family is described by onsemi as an internally compensated dual low-noise operational amplifier. Compared with general-purpose operational amplifiers, the NE5532 family was developed for improved noise performance and applications such as high-quality audio equipment and instrumentation. Two independent amplifiers can implement noninverting, inverting, summing, active-filter, buffer, and feedback-control stages, although each channel requires appropriate supply decoupling and feedback-network design. Typical applications include audio preamplifiers and mixer stages, microphone preamplification, active crossover and equalization networks, low-level sensor signal conditioning, laboratory instrumentation, oscilloscope input drivers, and audio interface circuits. In each case, the dual SOIC package can simplify board layout by placing two related amplifier functions close together. The low-noise characterization is particularly valuable when the source impedance is high or when the output must preserve small signals without adding unnecessary circuit noise. When designing around the NE5532AD8R2G, engineers should verify the exact input common-mode range, output swing, slew rate, input bias current, and channel-to-channel behavior against the manufacturer datasheet for the selected operating conditions. Input and output bypassing capacitors should be placed close to the relevant pins, and feedback components should be selected for the intended gain and bandwidth. Power-supply noise can also enter an audio or instrumentation path, so clean supply distribution remains as important as the amplifier itself. This product page combines the verified distributor and manufacturer-related source information with package, sourcing, comparison, and design guidance. It distinguishes published facts from unavailable parameters, preserves the original NE5532AD8R2G ordering code, and identifies only same-package drop-in candidates for engineering review. Final component selection should always include a full datasheet, pinout, and application-specific comparison before PCB substitution.

RFQ پەیوەندی
NE5532ADR - 30V, 10MHz Dual Low-Noise Op Amp | Texas Instruments
NE5532ADR

NE5532ADR - 30V, 10MHz Dual Low-Noise Op Amp | Texas Instruments

The Texas Instruments NE5532ADR is a dual low-noise operational amplifier for audio applications, specified for ±5 V to ±15 V supplies, with a 10 MHz gain-bandwidth product and 9 V/µs slew rate, housed in an 8-pin SOIC package. The device combines two amplifiers in one package and is intended for low-noise audio preamplification, mixing, filtering, and similar signal-conditioning circuits. An operational amplifier is a voltage-feedback amplifier whose open-loop gain is used to create closed-loop gain with external feedback components. The low-noise operational amplifier category is part of the broader analog signal-processing hierarchy: operational amplifier, analog IC, and semiconductor. NE5532-family devices became established choices in audio circuitry because they combine low input noise, adequate bandwidth, high slew rate, and wide supply-voltage capability in a conventional through-hole-compatible or surface-mount package. Key verified attributes include a 30 V maximum supply rating, dual-amplifier configuration, 10 MHz bandwidth, 9 V/µs slew rate, and operation over ±5 V to ±15 V. According to the Texas Instruments manufacturer datasheet, the NE5532x grade is specified from 0°C to 70°C, while the electrically similar SA5532x grade extends the operating range to -40°C to +85°C. These distinctions matter when selecting between commercial-temperature and industrial-temperature versions. The NE5532ADR uses the standard dual-operational-amplifier arrangement, allowing each amplifier to be configured independently for non-inverting, inverting, summing, filtering, or active-amplifier functions. Its 8-pin SOIC package supports compact, surface-mount PCB construction while preserving a conventional dual-op-amp footprint. Designers should still verify output-current, output-voltage swing, input-bias-current, noise-density, and open-loop-gain requirements against the complete manufacturer electrical-characteristics tables. Typical applications include stereo audio preamplifiers, active crossover filters, microphone preamplifiers, line-level mixers, and small-signal audio output stages. Its 10 MHz bandwidth is well above the audible band, while its low-noise designation makes it appropriate for amplifying weak audio signals without adding unnecessary broadband noise. The 9 V/µs slew rate also helps preserve low distortion when processing larger transient waveforms. The primary design consideration is power-supply configuration. The manufacturer datasheet specifies operation from ±5 V to ±15 V, and dual-supply operation generally simplifies bipolar audio-signal handling around ground. Designers must observe the output-swing limits, avoid excessive capacitive loading, and maintain suitable decoupling close to the supply pins. Stable feedback networks and appropriately chosen compensation or load conditions are important for reliable closed-loop operation. This page combines verified manufacturer and distributor information with pinout guidance, practical application fit, drop-in comparison data, and engineering-focused selection notes. The comparison also distinguishes true pin-compatible options from devices that may sound different or require different supply and stability considerations.

RFQ پەیوەندی
NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI
NE5532ADRE4

NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI

The Texas Instruments NE5532ADRE4 is a dual, general-purpose low-noise operational amplifier with a 10 MHz unity-gain bandwidth, 9 V/µs slew rate, and typical equivalent input noise voltage of 5 nV/√Hz at 1 kHz, supplied in an 8-SOIC package. It is intended for audio applications operating from ±5 V to ±15 V, with the NE5532x grade specified over 0°C to 70°C. Both amplifier channels share the same compact surface-mount package, allowing one component to support stereo signal paths. A low-noise operational amplifier is an analog integrated circuit that amplifies voltage differences while contributing minimal intrinsic noise. The NE5532 belongs to the operational-amplifier hierarchy used for audio preamplification, mixing, buffering, filtering, and instrumentation. Its 5 nV/√Hz typical input-noise characteristic is especially relevant when the amplified signal is sourced from a high-impedance sensor or a low-level microphone. The device provides 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, 100 dB typical common-mode rejection, and 100 V/mV typical DC voltage gain. These characteristics support audio-band operation with ample bandwidth for feedback networks and active filters. The dual configuration reduces component count in stereo circuitry, while the 8-SOIC package is compatible with automated surface-mount assembly. The NE5532 uses a conventional voltage-feedback operational-amplifier architecture with two independent amplifiers. Each channel provides inverting and non-inverting inputs, an output, and a power-supply connection. Noise and common-mode rejection are important because they influence the signal-to-noise ratio and the degree to which unwanted supply or common-mode signals appear at the output. Operating from a dual supply also supports bipolar audio signals without biasing the source at mid-rail. Typical applications include stereo audio preamplifiers, microphone amplifiers, line-level mixers, tone-control circuits, active crossover networks, and low-level audio buffers. In each case, the low-noise input stage helps preserve small signals, while the 10 MHz bandwidth and 9 V/µs slew rate provide margin for gain and phase shaping. Designers must still verify stability with the selected feedback network and load. The principal design consideration is power-supply bypassing. Place the required input and output decoupling capacitors close to the device pins, keep output routing short, and avoid placing long traces beside noisy switching nodes. Decoupling values and stability guidance should be taken directly from the manufacturer datasheet and typical application circuit rather than inferred from the distributor summaries. This page combines verified manufacturer information, distributor pricing, pin-compatible substitute references, and practical application guidance. The alternatives are explicitly limited to same-package drop-in candidates, while unavailable electrical details remain marked for validation against each candidate manufacturer’s current datasheet.

RFQ پەیوەندی
NE5532ADRG4 - Dual 10 MHz Low-Noise Op Amp | Texas Instruments
NE5532ADRG4

NE5532ADRG4 - Dual 10 MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532ADRG4 is a dual, general-purpose operational amplifier with a 10 MHz gain-bandwidth product, 9 V/µs slew rate, and 5 nV/√Hz typical equivalent input-noise voltage at 1 kHz, housed in an 8-pin SOIC package. The device provides two independent amplifiers and a 100 dB typical common-mode rejection ratio for audio, instrumentation, filtering, and low-level signal-conditioning applications. An operational amplifier is an active analog signal-conditioning device that uses high-gain differential feedback to amplify the difference between its two inputs. The dual NE5532 family belongs to the operational-amplifier hierarchy within analog and amplifier ICs. Its two channels can amplify noninverting and inverting signals independently, making it suitable for preamplifiers, active filters, mixers, buffers, and control loops where low noise, moderate bandwidth, and relatively high output-current capability are useful together. The NE5532ADRG4 combines a 10 MHz typical unity-gain bandwidth with 9 V/µs typical slew rate. Its typical high DC voltage gain is 100 V/mV, while the equivalent input-noise voltage is 5 nV/√Hz at 1 kHz. These characteristics support low-distortion audio signal paths and general feedback-control circuits without requiring a high-speed bipolar or current-feedback amplifier. Internally, the device uses a bipolar-compatible low-noise amplifier architecture intended for general-purpose precision audio work. Noise performance is especially important when the circuit handles microphone-level, musical-instrument, or balanced-line signals because amplifier noise can establish the input-referred noise floor. The common-mode rejection specification supports rejection of shared interference on differential inputs, while the two-amplifier configuration reduces package count in balanced and stereo circuits. Typical uses include stereo audio preamplification, active equalizer and crossover stages, microphone and line-level signal conditioning, instrumentation buffers, and low-frequency filter networks. In a preamplifier, both channels can process left and right signals while preserving low-noise performance. In an active filter, the 10 MHz bandwidth provides more open-loop capability than the audio-band signal being shaped, although stability must be verified for the selected noise gain and load. Designers should keep feedback-loop compensation appropriate for the selected gain, check output swing into the intended load, and provide stable decoupling at the supply pins. Because the available verified data does not state the complete supply-voltage range, input common-mode limits, output-current limits, or thermal resistance, those values must be confirmed in the manufacturer datasheet before final design release. This product page consolidates verified distributor specifications, pricing context, same-package replacement candidates, and application-oriented engineering guidance. It separates documented facts from unavailable parameters, helping engineers evaluate the NE5532ADRG4 quickly without mistaking an incomplete web summary for a complete electrical characterization.

RFQ پەیوەندی
NE5532AN - Dual Low-Noise 10 MHz Op Amp | onsemi
NE5532AN

NE5532AN - Dual Low-Noise 10 MHz Op Amp | onsemi

The onsemi NE5532AN is a dual, high-performance, internally compensated, low-noise operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin DIP package measuring 0.300 inch (7.62 mm). Compared with standard general-purpose operational amplifiers, the NE5532 family provides improved noise performance, stronger output drive capability, and better small-signal and power-bandwidth performance. A low-noise operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its two inputs while seeking low added noise and low distortion. In the product hierarchy, the NE5532AN belongs to the operational-amplifier family, which is part of amplifier ICs and, more broadly, analog semiconductors. Its two amplifiers share one package while providing independent input, output, and supply connections. The principal verified characteristics include a dual amplifier configuration, internally compensated operation, a 10 MHz gain-bandwidth product, and an 8-DIP package. The associated NE5532x family is specified for operation over a ±5 V to ±15 V supply range. The commercial NE5532x temperature range is stated as 0°C to 70°C, while the SA5532x family is specified from -40°C to +85°C. Exact input-offset, input-bias-current, output-voltage, and output-current limits were not included in the supplied data and therefore remain unspecified on this page. Internally compensated operation allows each amplifier to operate as a stable closed-loop stage without an external compensation network. This simplifies analog circuit design while preserving the low-noise characteristics valued in audio equipment. The stronger output-drive capability described in the manufacturer data helps the amplifier maintain low distortion when driving the next stage or a termination load. The 10 MHz gain-bandwidth figure provides useful bandwidth for low-frequency signal conditioning and audio preamplification rather than high-speed instrumentation applications. Typical uses include stereo audio preamplifiers, active tone-control stages, mixer input stages, headphone-driver interfaces, active crossover filters, and low-level signal conditioning. Its dual configuration is particularly useful when a board needs two similar amplifier channels, such as left and right audio paths. For lower-voltage or extended-temperature requirements, the related SA5532x grade should be evaluated separately rather than assuming NE5532AN covers those conditions. The primary design consideration is supply-headroom management: the stated family specification applies from ±5 V to ±15 V, so the circuit must remain within that operating range at every temperature and load condition. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier in a dual package should be configured according to the manufacturer guidance rather than left floating. This page consolidates the verified package, supply-range, temperature-class, bandwidth, and cross-reference information for the NE5532AN, then adds application guidance, strict same-package drop-in comparisons, and practical selection criteria for engineers evaluating this dual low-noise operational amplifier.

RFQ پەیوەندی
NE5532ANG - Dual Low-Noise 8-PDIP Op Amp | onsemi
NE5532ANG

NE5532ANG - Dual Low-Noise 8-PDIP Op Amp | onsemi

onsemi NE5532ANG is a dual, internally compensated low-noise operational amplifier with two amplifier circuits in an 8-pin PDIP package. Its specified operating supply range is 3 V to 20 V, and its design combines low-noise operation with the output-drive capability expected from the NE5532 family. The device is intended for audio and general-purpose signal-conditioning applications requiring two amplifiers in one package. Each integrated amplifier provides differential inputs, an output, and the usual dual-amplifier power connections in the standard 8-pin arrangement. An operational amplifier is a voltage-feedback amplifier that uses external feedback to control gain and signal behavior. A dual operational amplifier combines two amplifier channels in one package, reducing board area compared with separate single-channel devices. In the broader semiconductor hierarchy, the NE5532ANG belongs to the operational-amplifier family, which sits within amplifier ICs and analog signal-conditioning semiconductors. Its internal compensation simplifies implementation by allowing the manufacturer to establish stable operation without requiring a large external compensation network. The primary engineering benefits are low input noise, dual-channel integration, and an 8-pin PDIP package suitable for conventional through-hole PCB assembly. Two amplifier circuits can implement functions such as preamplification, filtering, buffering, active crossover stages, or audio channel processing in a single package. The onsemi listing identifies the NE5532ANG as a standard general-purpose amplifier, while the manufacturer datasheet describes it as an internally compensated dual low-noise operational amplifier. The NE5532 family is recognized for audio-focused signal-chain use, but its applications extend beyond simple volume control. Low-noise operation is valuable when the amplifier must preserve small signals without adding excessive broadband noise. Internal compensation supports practical feedback-based amplifier configurations, and the dual format allows a designer to use both amplifier sections for related analog functions rather than placing two separate packages on the board. Typical uses include stereo audio preamplification, headphone-driver signal stages, active equalizer and crossover circuits, low-level sensor amplification, and general instrumentation buffers. The same package can also support two independent channels in test equipment or measurement interfaces. Selection should be based on the required supply voltage, signal amplitude, output loading, noise target, stability in the selected feedback network, and the surrounding circuit impedance. For PCB implementation, follow the pin-description table in the manufacturer datasheet when assigning input, output, and supply traces. Place the manufacturer-recommended bypass capacitors close to the supply pins, keep input routing short and away from high-current switching nodes, and provide adequate output-current and thermal margin. Because the NE5532ANG is a through-hole PDIP device, verify the PCB drill pattern and pin-1 orientation rather than assuming a surface-mount footprint. This page combines the exact manufacturer and distributor identity of NE5532ANG with package-specific pin guidance, application-oriented circuit considerations, drop-in replacement analysis, and an explicit separation of confirmed characteristics from parameters that still require engineering verification.

RFQ پەیوەندی
NE5532AP - Dual Low-Noise Op Amp, 10MHz, 8-PDIP | Texas Instruments
NE5532AP

NE5532AP - Dual Low-Noise Op Amp, 10MHz, 8-PDIP | Texas Instruments

The Texas Instruments NE5532AP is a dual high-performance, low-noise operational amplifier supplied in an 8-pin PDIP (through-hole) package. Each of the two internal op-amps delivers 10 MHz unity-gain bandwidth, a 5 nV/√Hz input noise voltage at 1 kHz, 100 dB typical CMRR, and a 100 V/mV typical DC voltage gain. The device is specified for ±5 V to ±15 V dual supply operation and drives 600 ohm loads directly, making it a workhorse in professional and consumer audio designs. An operational amplifier (op-amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, usually, a single-ended output. Within the broader taxonomy, an op-amp belongs to the linear IC family -> amplifier ICs -> analog signal conditioning -> semiconductor. Low-noise audio-grade op-amps such as the NE5532 are designed to add minimal hiss and distortion when placed in the signal path of pre-amplifiers, mixers, equalizers, and line drivers, distinguishing them from general-purpose op-amps (e.g., TL072) that trade noise performance for cost or bandwidth. Key differentiating features of the NE5532AP include: 5 nV/√Hz equivalent input noise voltage (typ. at 1 kHz), 32 V peak-to-peak output swing with ±18 V supplies into 600 ohm, input protection diodes, output short-circuit protection, and a high slew rate that enables clean transient response in fast audio signals. The 8-PDIP package simplifies prototyping on breadboards and through-hole production boards, and is widely accepted in long-lifecycle industrial products where socketing and field replacement are valued. Architecturally, the NE5532 uses a bipolar transistor input stage and a class AB output stage. The bipolar front-end delivers the low voltage noise and high DC gain that JFET-input op-amps cannot match, at the cost of higher input bias current (which is acceptable in audio-coupling networks with series capacitors). The 600 ohm drive capability means the NE5532AP can directly feed pro-audio line inputs without an additional buffer. Typical applications include studio-quality microphone pre-amplifiers, mixing consoles, equalizer and crossover filter boards, audio DAC output buffers, headphone amplifiers, and instrumentation front-ends. The wide supply range also allows use in industrial control signal conditioning where dual rails are already present. When designing with the NE5532AP, observe the input common-mode range: the inputs must stay within the supply rails, and large differential voltages should be limited by external series resistance to avoid damaging the input-protection structures. Decouple both supply pins with 100 nF ceramics placed within 10 mm of the device. This page consolidates distributor pricing, drop-in DIP-8 alternatives, and practical audio design notes - information not assembled in the manufacturer datasheet alone - to support BOM decisions for new designs and legacy maintenance.

RFQ پەیوەندی
NE5532APG4 - 10MHz Dual Audio Op Amp | Texas Instruments
NE5532APG4

NE5532APG4 - 10MHz Dual Audio Op Amp | Texas Instruments

The Texas Instruments NE5532APG4 is a dual general-purpose operational amplifier with a 10 MHz gain-bandwidth product, supplied in an 8-pin dual in-line package. The verified distributor data identifies two amplifier circuits, a general-purpose audio classification, and a through-hole 8-DIP package measuring 0.300 inches with 7.62 mm lead pitch. One distributor reports a $0.6560 unit price and 4,320 pieces in stock as of 2026-10-22. An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, filter noise, and drive feedback-controlled circuits. A dual amplifier contains two amplifier channels in one package. The NE5532 family is especially recognizable in audio signal paths because it is commonly associated with low-noise audio preamplification, mixing, and output-stage applications. Within the broader hierarchy, it is an amplifier IC, an analog integrated circuit, and a general-purpose semiconductor. The available data confirms two amplifier circuits and a 10 MHz bandwidth-related figure, while the manufacturer-specific electrical limits were not included in the supplied source set. Accordingly, specifications for supply voltage, input offset voltage, input-bias current, noise density, output swing, slew rate, operating temperature, and channel-to-channel matching are marked as needing primary-source verification. This conservative approach prevents generic NE5532-family figures from being presented as verified facts for this exact suffix and package. Its 8-DIP package is appropriate for prototypes, educational instruments, repair work, and through-hole audio boards where socketed replacement is useful. The larger package also makes the part straightforward to probe and exchange, although it occupies more PCB area than a surface-mount dual op amp. Circuit layout still requires short feedback paths, clean grounding, and appropriate supply bypassing to preserve stability and low-noise performance. Typical uses include stereo audio preamplification, active tone control, headphone-buffer stages, mixer input conditioning, and general low-frequency signal processing. These applications align with the device's stated general-purpose amplifier classification and dual-channel configuration. Exact stability, bandwidth, noise, and output-drive claims should be checked against the official Texas Instruments datasheet before setting gain-bandwidth requirements. For new designs, verify the exact NE5532APG4 suffix, supply rails, input common-mode range, output swing, and thermal conditions in the manufacturer datasheet. When repairing an existing board, preserve the original pin orientation and socket the device only after confirming that the installed part is electrically and mechanically compatible. The 7.62 mm pitch through-hole package is mechanically different from common SOIC-8 variants even where some signal functions resemble them. This page consolidates verified distributor availability, package information, pricing, cross-reference research, and practical replacement guidance beyond a raw distributor listing. Unknown electrical values are deliberately identified rather than inferred from the broader NE5532 family.

RFQ پەیوەندی
NE5532APS - Dual 10MHz Low-Noise Op Amp | Texas Instruments
NE5532APS

NE5532APS - Dual 10MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments NE5532APS is a dual low-noise operational amplifier intended primarily for audio signal conditioning. The device provides two amplifiers, a 10 MHz gain-bandwidth product, and operation from ±5 V to ±15 V in an 8-pin SOP package. It is the surface-mount packaging option for the NE5532 family and is identified as an active product by the manufacturer’s product information. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase the difference between two input voltages. Operational amplifiers belong to the amplifier IC hierarchy and are commonly used in audio, control, measurement, and signal-processing circuits. The NE5532 family emphasizes low-noise performance, wide bandwidth, and practical dual-channel integration for applications requiring two similar amplifier functions in one package. The NE5532APS combines a 10 MHz gain-bandwidth product with a slew rate of 9 V/µs. Its specified supply range of ±5 V to ±15 V accommodates conventional bipolar analog rails, including ±12 V and ±15 V systems. The NE5532x grade is specified for operation from 0°C to 70°C, while the electrically related SA5532x family extends the operating range from -40°C to +85°C. The NE5532APS is packaged for surface-mount assembly in an 8-pin SOP configuration. Each internal amplifier has a differential input stage, a high-gain intermediate stage, and a push-pull output stage. The two amplifiers share supply pins but otherwise provide independent signal paths, allowing one device to implement stereo audio channels, balanced differential functions, active filtering, or a combination of buffering and gain. Stable operation around the unity-gain frequency and its 10 MHz bandwidth make it suitable for audio-frequency amplification and feedback networks. Typical uses include stereo audio preamplification, microphone preamplifiers, active crossover filters, line-level buffers, tone controls, and small-signal audio stages. It can also support low-frequency measurement or instrumentation circuits when the input signal remains within its common-mode and output-voltage limits. In each case, external resistor and capacitor networks determine the actual gain, bandwidth, and filtering response. The main design consideration is power-rail compatibility. The device expects bipolar supplies within ±5 V to ±15 V and does not operate from a single 5 V rail under its specified conditions. Designers should preserve input and output headroom, avoid excessive capacitive loading at the output, and select external feedback values that keep the closed-loop bandwidth and stability appropriate for the intended signal. This page combines the manufacturer’s device specifications with package details, sourcing guidance, application guidance, and an engineering-focused review of replacement considerations. It also distinguishes genuine pin-compatible options from devices that merely provide similar audio performance, helping designers avoid changes that require PCB or signal-path redesign.

RFQ پەیوەندی