EPM7128STC100-6N - MAX 7000S 128-Macro-Cell CPLD | Altera | TQFP-100
Teilenummer: EPM7128STC100-6N ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $14 | $1.400,00 |
| 500 | $12.1 | $6.050,00 |
| 1.000 | $10.5 | $10.500,00 |
EPM7128STC100-6N Übersicht
What is a CPLD? A Complex Programmable Logic Device (CPLD) is a non-volatile programmable logic device that sits between simple PAL/GAL chips and FPGAs in the programmable logic hierarchy. CPLDs use EEPROM or flash configuration memory, provide deterministic timing with predictable propagation delays, and typically include on-chip non-volatile storage - making them ideal for glue logic, bus interfacing, and power-up configuration tasks. Within the taxonomy, EPM7128STC100-6N belongs to: CPLD > Complex Programmable Logic Device > Programmable Logic Device > Semiconductor IC.
Key features include 250 MHz internal counter frequency, IEEE 1149.1 JTAG boundary-scan support, in-system programmability (ISP) via JTAG, multi-volt core and I/O operation, and 5V-tolerant I/Os. The device is fabricated on a CMOS EEPROM process and supports Altera's Quartus and MAX+PLUS II development environments for schematic, VHDL, and Verilog HDL design entry.
The MAX 7000S architecture combines a Programmable Logic Array (PLA) with a Programmable Logic Device (PLD) macro-cell structure, providing each macro cell with a configurable register, product-term selection, and programmable I/O. This architecture yields fast, deterministic propagation delays and high logic density per I/O pin, suitable for high-speed glue-logic and state-machine applications.
Typical applications include address decoding for microprocessor and DSP systems, peripheral bus interface bridging (PCI, ISA, VME), state-machine control for industrial automation, bus arbitration and protocol conversion in telecommunications, and legacy system upgrade paths requiring 5V-tolerant logic. The 5V tolerant I/Os allow direct interface to legacy TTL logic without level shifters.
When designing with this part, verify power-supply decoupling: each VCC/VCCIO pin should have a 0.1 microfarad ceramic decoupling capacitor placed within 3 mm of the pin. Unused I/O pins should be configured as outputs driving ground to minimize power consumption.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Drop-in-Alternativen für EPM7128STC100-6N – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit EPM7128STC100-6N (gleiche Bauform und Footprint) – abweichend in Package, Logic Array Blocks (LABs), RoHS Status, Operating Temperature, Family.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
EPM7128STC100-6
✅ Drop-In✓ Auf Lager
$5.2 / Stück
Datenblatt ansehen →EPM7128STC100-10N
✅ Drop-In✓ Auf Lager
$9.3 / Stück
Datenblatt ansehen →EPM7128STC100-15N
✅ Drop-In✓ Auf Lager
$9.2 / Stück
Datenblatt ansehen →EPM7128SQC100-7N
✅ Drop-In✓ Auf Lager
$7.1 / Stück
Datenblatt ansehen →EPM7128SQC100-10N
✅ Drop-In✓ Auf Lager
$14.95 / Stück
Datenblatt ansehen →EPM7128AETC100-7N
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$31.8 / Stück
Datenblatt ansehen →EPM7128STC100-6N Grenzwerte & elektrische Eigenschaften
| Family | MAX 7000S |
| Usable Gates | 2,500 |
| Macro Cells | 128 |
| User I/Os | 84 |
| Logic Family | CMOS |
| Anzahl der Pins | 100 |
| Package Type | TQFP-100 |
| Maximum Internal Frequency | 147.1 MHz |
| Internal Counter Frequency | 250 MHz |
| Propagation Delay (tPD) | 6 ns |
| Pin-to-Pin Delay | 4.5 ns |
| Supply Voltage (VCCIO) | 5 V |
| Process Technology | CMOS EEPROM |
| Programmability | In-System Programmable (ISP) via JTAG |
| JTAG Support | IEEE 1149.1 Boundary Scan |
| Betriebstemperatur | 0C to +70C (Commercial) |
| Montageart | Surface Mount |
| RoHS-Status | Non-Compliant (lead-bearing package) |
EPM7128STC100-6N tqfp-100 Pinbelegungsleitfaden
Pinbelegung für EPM7128STC100-6N (tqfp-100-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für EPM7128STC100-6N.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
EPM7128STC100-6N ist geeignet für 7 Anwendungs: Microprocessor Address Decoding, PCI/ISA/VME Bus Interface Bridging, Industrial Control State Machines, Legacy System Upgrades (5V TTL Replacement), Telecommunications Protocol Conversion, Test & Measurement Equipment Front-End Logic, Avionics & Military Legacy Interfaces.
Microprocessor Address Decoding
The EPM7128STC100-6N is ideal for address-decoding and chip-select generation in legacy 5V microprocessor and DSP systems. With 128 macro cells and 84 user I/Os, it can replace multiple 74LS/74FTTL decoder packages with a single in-system-programmable device, simplifying PCB layout. Its 6 ns propagation delay is well below typical 25-33 MHz memory-bus cycle times, providing comfortable timing margin for synchronous DRAM, Flash, and peripheral chip-select generation.
Empfohlen
PCI/ISA/VME Bus Interface Bridging
The EPM7128STC100-6N serves as a bus-interface bridge between legacy 5V buses (PCI, ISA, VME) and modern peripherals, with 84 I/Os sufficient for full 32-bit data plus control/address signals. Its 5V-tolerant I/Os connect directly to TTL-level buses without level shifters, and the deterministic 6 ns pin-to-pin delay simplifies timing closure. The JTAG ISP interface enables in-field firmware updates for protocol-conversion logic.
Empfohlen
Industrial Control State Machines
Factory automation systems benefit from the EPM7128STC100-6N's deterministic timing and EEPROM non-volatile configuration, which provides instant-on behavior without external boot memory. Each macro cell's product-term logic efficiently encodes Moore and Mealy state machines for motor-control sequencing, sensor debouncing, and safety-interlock logic. The wide 0C to +70C commercial operating range suits most factory-floor enclosures.
Empfohlen
Legacy System Upgrades (5V TTL Replacement)
Engineers maintaining 1980s-1990s test equipment, instrumentation, and industrial controllers use the EPM7128STC100-6N as a modern, in-system-programmable replacement for racks of 74LS/74AS/74F glue-logic ICs. A single CPLD can absorb 5-10 discrete decoder, latch, and multiplexer packages, reducing board area and BOM cost. The 5V VCCIO allows direct solder-in replacement of legacy logic without PCB rework.
Empfohlen
Telecommunications Protocol Conversion
Telecom line cards and base-station controllers use the EPM7128STC100-6N for protocol conversion between legacy E1/T1 framing, HDLC channels, and proprietary backplane buses. The 84 I/Os handle multiple full-duplex serial channels plus parallel control/status registers, and the 6 ns tPD supports bit-rate conversion up to 80 Mbps. JTAG ISP simplifies factory provisioning and field firmware upgrades.
Empfohlen
Test & Measurement Equipment Front-End Logic
Bench-top oscilloscopes, logic analyzers, and signal generators use the EPM7128STC100-6N for trigger logic, channel multiplexing, and front-panel I/O scanning. The 5V-tolerant I/Os interface directly with legacy analog front-end ICs, and the deterministic 4.5 ns pin-to-pin delay ensures clean trigger-event timing. The in-system programmability enables last-minute feature additions without board respins.
Empfohlen
Avionics & Military Legacy Interfaces
Although the commercial-grade EPM7128STC100-6N operates only to 70C, the same MAX 7000S die is available in industrial and military temperature grades (EPM7128STI100-6N, EPM7128STC100-6) for avionics retrofit programs. The 5V-tolerant I/Os interface directly with MIL-STD-1553 and ARINC 429 transceivers without level translation, simplifying legacy airframe upgrades.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für EPM7128STC100-6N – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | EPM7128STC100-6 | EPM7128STC100-10N | EPM7128STC100-15N | EPM7128SQC100-7N | EPM7128AETC100-7N |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) |
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Family | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000A |
| Macro Cells | 128 | 128 | 128 | 128 | 128 | 128 |
| User I/Os | 84 | 84 | 84 | 84 | 84 | 84 |
| Propagation Delay (tPD) | 6 ns | 6 ns | 10 ns | 15 ns | 7.5 ns | 7.5 ns |
| Maximum Internal Frequency | 147.1 MHz | 147.1 MHz | 100 MHz | 76.9 MHz | 125 MHz | 125 MHz |
| Supply Voltage (VCCIO) | 5 V | 5 V | 5 V | 5 V | 5 V | 3.3 V |
| RoHS Status | Non-compliant (lead-bearing) | Compliant (lead-free) | Non-compliant | Non-compliant | Non-compliant | Non-compliant |
| Lifecycle Status | Obsolete (PDN 2017) | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Wichtigste Unterscheidungsmerkmale
- Fastest speed grade in MAX 7000S TQFP-100 family (vs. EPM7128STC100-10N)
- Larger logic capacity than PQFP-100 alternatives (vs. EPM7128SQC100-7N)
- 5V-native operation vs MAX 7000A 3.3V core (vs. EPM7128AETC100-7N)
Designhinweise
Estimated: at maximum toggle rate the EPM7128STC100-6N ICC is approximately 300-500 mA from VCC (5V). Place one 0.1 microfarad X7R ceramic decoupling capacitor within 3 mm of each VCC/VCCIO pin, and add a single 10 microfarad tantalum or aluminum-polymer bulk capacitor near the package. ICC rises sharply above 50 MHz internal frequency; use a star-ground topology to keep digital switching noise out of analog supply sections.
The TQFP-100 package has a 0.5 mm pitch and requires careful PCB layout. Use 0.15 mm/0.20 mm trace width with matched length pairs for high-speed signals, and provide a solid ground plane on the layer immediately beneath the CPLD. JTAG signals (TCK, TMS, TDI, TDO) should be routed with 4-8 mil traces and series 33 ohm terminators if the JTAG cable exceeds 150 mm length.
Do NOT connect EPM7128STC100-6N I/O pins directly to a 3.3V-only bus while VCCIO is at 5V - this violates the absolute-maximum VCCIO+0.3V clamp. For mixed-voltage designs, set VCCIO to 3.3V; the I/Os remain 5V-tolerant per the datasheet. Unused I/O pins MUST be configured as outputs driving ground via Quartus device-options to minimize quiescent current.
When using the EPM7128STC100-6N for high-speed bus multiplexing above 50 MHz, add 22-33 ohm series damping resistors on each output to control overshoot and ringing. The CMOS output structure has roughly 5-7 ns edge rates which can excite resonances on unterminated traces longer than 50 mm. Quartus II pin-assignment tools should reserve output-pins adjacent to high-edge-rate signals for ground or unused-output configurations.
Compliance-Informationen
N suffix in part number indicates lead-bearing (SnPb) finish, NOT RoHS compliant. Part was discontinued by Altera/Intel in June 2017 (PDN). Same die available in lead-free finish as EPM7128STC100-6 (no N suffix). REACH and conflict-minerals status not declared by manufacturer.