10AS057H2F34I2SG - Arria 10 SX SoC FPGA, 570K LE, Dual A9 | Intel
Référence : 10AS057H2F34I2SG ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $8500 | $8 500,00 |
| 10 | $8200 | $82 000,00 |
| 100 | $7800 | $780 000,00 |
| 500 | $7400 | $3 700 000,00 |
| 1 000 | $7100 | $7 100 000,00 |
10AS057H2F34I2SG Présentation
An SoC FPGA is a heterogeneous computing device that combines general-purpose application processor cores with programmable fabric on a single die, enabling designers to partition workloads between hardware acceleration in the FPGA and software execution on the ARM cores for the lowest possible latency and power. The Arria 10 SX family targets mid-range applications that require both deterministic hardware processing and a rich software stack.
Key specifications for the 10AS057H2F34I2SG include 570K logic elements, dual ARM Cortex-A9 cores with CoreSight, on-chip processor subsystems with peripherals, high-speed transceivers up to 1.5 GHz effective data rate, hardened memory controllers, and the 0.9 V core voltage typical of the 20 nm Arria 10 generation. The industrial temperature grade and -2 speed bin indicate balance between performance and timing margin for non-extended use cases.
Architecturally, the device combines a hard processor system (HPS) with hardened peripherals such as Ethernet MAC, USB, SD/MMC, NAND flash controllers, and DDR memory controllers, all connected to the FPGA fabric via high-bandwidth bridges. The 20 nm process enables higher logic density and lower dynamic power than the previous 28 nm Arria V generation, while maintaining transceivers and DSP blocks suited to wireless infrastructure and video processing.
Typical applications include wireless baseband processing, software-defined radio, radar signal processing, video broadcasting equipment, industrial machine vision, and secure communications. The Arria 10 SX is also widely used in test and measurement and medical imaging systems requiring simultaneous ARM-based control and FPGA-based data plane.
When designing with this device, pay close attention to PCB layout for the FCBGA-1152 package, including microvia stack-up, signal-integrity simulation for 1.5 GHz transceivers, and proper decoupling. Quartus Prime is the primary tool chain; configuration via JTAG, AS, or fast passive parallel modes is supported.
This page synthesizes distributor pricing, same-family Altera Arria 10 SX drop-in alternatives, and design context not present in the standalone datasheet, helping engineers quickly compare and source the part.
Alternatives de remplacement direct pour 10AS057H2F34I2SG — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec 10AS057H2F34I2SG (même facteur de forme et même empreinte) — différant par Package, Speed Grade, Logic Elements, Mounting Type, Process Technology.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
10AS057H2F34I2LG
✅ Remplacement direct✓ En stock
$3675 / unité
Voir la fiche technique →10AS057H2F34I1HG
✅ Remplacement direct✓ En stock
$4980.3 / unité
Voir la fiche technique →10AS057H2F34E2SG
✅ Remplacement direct✓ En stock
$3250 / unité
Voir la fiche technique →10AS057H2F34E2LG
✅ Remplacement direct✓ En stock
$2524.1 / unité
Voir la fiche technique →10AS057H2F34E1HG
✅ Remplacement direct✓ En stock
$3050 / unité
Voir la fiche technique →10AS057H1F34I1HG
✅ Remplacement direct✓ En stock
$3500 / unité
Voir la fiche technique →10AS057H1F34E1HG
✅ Remplacement direct✓ En stock
$3300 / unité
Voir la fiche technique →10AS057H2F34I2SG Valeurs maximales et caractéristiques électriques
| Family | Arria 10 SX SoC FPGA |
| Logic Elements | 570000 |
| Process Technology | 20 nm |
| Core Voltage | 0.9 V |
| Hard Processor System | Dual ARM Cortex-A9 MPCore with CoreSight |
| Maximum User I/O | 492 |
| Boîtier | 1152-ball FCBGA (F34) |
| Package Dimensions | 35 x 35 mm |
| Type de montage | Surface Mount (Flip-Chip BGA) |
| Operating Temperature Grade | Industrial (-40C to +100C) |
| Speed Grade | -2 (mid-range) |
| Transceiver Data Rate | Up to 1.5 Gbps (effective) |
| Configuration | JTAG, AS, FPP |
| Statut RoHS | Compliant |
| Part Number Decoder - I2 | Industrial temperature grade |
| Part Number Decoder - SG | Lead-free, RoHS compliant, Pb-free F34 package |
Guide de configuration des broches du 10AS057H2F34I2SG 35 x 35 mm
Configuration des broches du 10AS057H2F34I2SG (boîtier 35 x 35 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour 10AS057H2F34I2SG.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
10AS057H2F34I2SG convient pour 6 applications: Wireless Baseband Processing, Software-Defined Radio, Video Broadcasting Infrastructure, Industrial Machine Vision Systems, Radar Signal Processing, Test and Measurement Instrumentation.
Wireless Baseband Processing
The 10AS057H2F34I2SG suits wireless baseband applications thanks to its 570K logic elements for high-throughput DSP pipelines, integrated 1.5 Gbps transceivers for CPRI/OBSAI fronthaul links, and dual ARM Cortex-A9 cores that run the MAC and upper layers while the FPGA fabric accelerates PHY and FEC. The Arria 10 SX SoC architecture reduces latency by eliminating chip-to-chip HPS-to-FPGA bridge interfaces, which is critical for LTE and 5G NR sub-6 GHz radio units.
Recommandé
Software-Defined Radio
The dual ARM Cortex-A9 MPCore in the 10AS057H2F34I2SG runs real-time control stacks, scheduling, and waveform management while the 570K LE fabric executes parallel demodulation, channelization, and digital up/down conversion. Transceivers operating up to 1.5 Gbps aggregate support multi-band RF sampling for tactical and commercial SDR platforms. Quartus Prime DSP Builder and SoC EDS provide a complete development path.
Recommandé
Video Broadcasting Infrastructure
The 570K logic elements of the 10AS057H2F34I2SG provide the resources needed for multi-stream HEVC/AVC encode and decode, video processing pipelines (deinterlacing, scaling, color conversion), and overlay graphics at 4K/60p and beyond. The hard ARM cores manage IP/UDP/SRT/RTP protocol stacks for contribution encoders and decoders, while FCBGA-1152 with 492 I/O supports simultaneous SDI, HDMI, and 10G Ethernet I/O.
Recommandé
Industrial Machine Vision Systems
The 10AS057H2F34I2SG combines high-throughput FPGA logic for image preprocessing and machine-learning inference with an ARM Cortex-A9 dual-core for system control, network connectivity, and HMI rendering. Industrial temperature grading (-40C to +100C) suits factory-floor deployment. Multiple MIPI or LVDS channels aggregated over 492 I/O interfaces with CoaXPress, GigE Vision, or USB3 Vision cameras.
Recommandé
Radar Signal Processing
The 570K LE fabric of the 10AS057H2F34I2SG handles FFT, beamforming, and pulse compression for phased-array radar, while 1.5 Gbps transceivers digitize ADC outputs and feed back digital control. The hard ARM cores run the tracker and display rendering. Industrial temperature and high pin count make it well-suited to airborne, ground-based, and maritime radar systems where deterministic latency matters.
Recommandé
Test and Measurement Instrumentation
The 10AS057H2F34I2SG enables high-end test equipment by combining FPGA-speed data acquisition with ARM-driven display and remote control logic. The 570K LE fabric executes parallel DSP for real-time spectral analysis, protocol decoding, and arbitrary waveform generation, while 1.5 Gbps transceivers feed data from high-speed ADCs/DACs. SoC integration reduces board complexity in oscilloscopes, logic analyzers, and signal analyzers.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour 10AS057H2F34I2SG — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | 10AS057H2F34I2LG | 10AS057H2F34I1HG | 10AS057H2F34E2SG | 10AS057H2F34E2LG |
|---|---|---|---|---|---|
| Package | 1152-ball FCBGA (F34), 35x35 mm | 1152-ball FCBGA (F34), 35x35 mm - same | 1152-ball FCBGA (F34), 35x35 mm - same | 1152-ball FCBGA (F34), 35x35 mm - same | 1152-ball FCBGA (F34), 35x35 mm - same |
| Brand | Intel (Altera) | Intel (Altera) - same | Intel (Altera) - same | Intel (Altera) - same | Intel (Altera) - same |
| Logic Elements | 570000 | 570000 | 570000 | 570000 | 570000 |
| Speed Grade | -2 | -2 | -1 (faster) | -2 | -2 |
| Temperature Grade | Industrial (-40C to +100C) | Industrial | Industrial | Extended | Extended |
| Lead-free Suffix | SG | LG | HG | SG | LG |
| User I/O | 492 | 492 | 492 | 492 | 492 |
| HPS Revision | H2 | H2 | H2 | H2 | H2 |
Principaux différenciateurs
- Highest user I/O among the 570K-LE Arria 10 SX F34 family (vs 10AS057K1F35E1SG)
- Industrial temperature grade with -2 speed balance (vs 10AS057H2F34E2SG)
- Dual-core ARM Cortex-A9 hard processor system integrated (vs 10AS048H2F34I2SG)
Notes de conception
The 1152-ball FCBGA at 35x35 mm has a typical theta_JA in the range of 0.4-1.0 C/W with proper thermal design (chip-scale BGA with thermal lid and adequate PCB copper). For industrial temperature operation up to +100C ambient, plan for at least 8-10 W continuous dissipation without airflow. Use the manufacturer's thermal model and follow the package lid-down mounting recommendations in the Arria 10 device datasheet.
Design a high-density PCB stack-up (typically 12-16 layers) with microvia arrays under the BGA for breakout. Pair each high-speed transceiver differential pair with continuous reference ground planes and follow the Arria 10 pin connection guidelines for length matching. Use the Intel/Altera Pin Connection Guidelines document to identify any pins that require specific termination or pull-up resistors.
Verify the HPS (hard processor system) pin multiplex mapping for SD/MMC, USB, EMAC, and NAND before PCB layout - the HPS peripheral I/O assignment differs across Arria 10 SX SKUs. Also confirm Quartus Prime version supports the silicon revision on the part. Configuring SoC FPGA via AS mode requires a compatible EPCQ flash device; consult the Arria 10 Configuration Handbook for supported densities and voltage rails.
Informations de conformité
Lead-free F34 FCBGA package; SG suffix indicates lead-free and RoHS compliance per Altera/Intel convention. Not AEC-Q100 qualified - choose automotive-grade Arria 10 devices for that requirement.
