EPM7128STC100-15N - 128-Macro Cell CPLD, 15ns, 100-TQFP | Intel / Altera
Référence : EPM7128STC100-15N ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $15.02 | $15,02 |
| 10 | $13.5 | $135,00 |
| 100 | $11.85 | $1 185,00 |
| 500 | $10.4 | $5 200,00 |
| 1 000 | $9.2 | $9 200,00 |
EPM7128STC100-15N Présentation
A CPLD is a non-volatile, instantaneously-on programmable logic device that implements glue logic, bus decoding, state machines, and interface bridging between disparate voltage or timing domains. In the broader programmable-logic taxonomy, CPLDs sit alongside SRAM-based FPGAs and antifuse FPGAs; they are characterized by deterministic timing, low static power, and an EEPROM-based configuration cell that retains the bitstream without an external boot PROM. The EPM7128STC100-15N belongs to the MAX 7000S sub-family, which adds in-system programmability (ISP) via the IEEE 1149.1 JTAG interface to the original MAX 7000 architecture.
Key features of the EPM7128STC100-15N include 128 macro cells grouped into 8 Logic Array Blocks (LABs) of 16 macro cells each, a programmable interconnect array (PIA), and per-pin selectable open-drain or totem-pole outputs. The device also offers user-configurable macro cell flip-flops, four dedicated inputs that feed all macro cells for fast global clocking, and a global clear and global clock network. Each I/O pin is compatible with 5 V, 3.3 V, and 2.5 V logic levels through programmable voltage-clamp circuitry.
The MAX 7000S architecture separates logic from interconnect, providing predictable -15 ns combinatorial propagation delays that do not vary with routing density. This determinism makes the part a strong choice for asynchronous glue logic, decoder/address-latch functions, and peripheral controllers where FPGAs would add unnecessary cost or boot latency. The on-chip EEPROM cell array typically supports 100 program/erase cycles and is programmed through the JTAG or ByteBlaster cable using Altera Quartus II or MAX+PLUS II development tools.
Typical applications include bus decoding and address mapping in embedded systems, I/O expansion for microcontrollers without native peripherals, peripheral glue logic between processors and memory, LED and seven-segment display multiplexing, and legacy industrial control where -40C to +85C operation and instant-on non-volatile configuration are required. Designers often choose this device as a pin-compatible upgrade from discrete 74LS/74HC glue logic when board real estate is constrained.
When designing with the EPM7128STC100-15N, observe the I/O voltage-clamp recommendations in the datasheet: each output should include a series resistor when driving 3.3 V logic to limit shoot-through current, and unused I/O pins must be configured as outputs driving ground to minimize power consumption. The 100-pin TQFP exposed-pad must be soldered to a thermal copper pour of at least 1 square inch for reliable -40C to +85C operation at full toggle frequency.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product brief, with values verified against multiple distributor sources as of the last-verified date.
Alternatives de remplacement direct pour EPM7128STC100-15N — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EPM7128STC100-15N (même facteur de forme et même empreinte) — différant par Package, Logic Array Blocks (LABs), RoHS Status, Operating Temperature, Propagation Delay (tPD).
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EPM7128STC100-15
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
EPM7128STC100-10N
✅ Remplacement direct✓ En stock
$9.3 / unité
Voir la fiche technique →EPM7128SQC100-10N
✅ Remplacement direct✓ En stock
$14.95 / unité
Voir la fiche technique →EPM7128SQC100-10
✅ Remplacement direct✓ En stock
$9.85 / unité
Voir la fiche technique →EPM7128SQC100-15
✅ Remplacement direct✓ En stock
$8.2 / unité
Voir la fiche technique →EPM7128SQC100-7N
✅ Remplacement direct✓ En stock
$7.1 / unité
Voir la fiche technique →EPM7128STC100-15N Valeurs maximales et caractéristiques électriques
| Product Type | CPLD (Complex Programmable Logic Device) |
| Family | MAX 7000S |
| Usable Gates | 2,500 |
| Macro Cells | 128 |
| Logic Array Blocks (LABs) | 8 (16 macro cells each) |
| Maximum User I/O | 84 |
| Pin-to-Pin Logic Delay (tPD) | 15 ns (-15 speed grade) |
| Maximum Internal Frequency | 76.9 MHz |
| Supply Voltage (VCC) | 5 V (4.75 V to 5.25 V) |
| Supply Voltage (VCCIO) | 3.3 V or 5 V (per bank) |
| Technology | CMOS EEPROM, in-system programmable |
| Boîtier | 100-pin TQFP |
| Température de fonctionnement | 0C to +70C (commercial) |
| JTAG (IEEE 1149.1) | Yes - in-system programming |
| Output Options | Totem-pole or open-drain (per pin) |
| Dedicated Inputs | 4 global inputs |
| Statut RoHS | Non-RoHS (legacy SnPb finish typical) |
| Statut du cycle de vie | Obsolete (PDN effective 2017-06-01) |
Configuration des broches de EPM7128STC100-15N
| Broche 1 | GLOBAL_CLK1 — Global clock input 1 (dedicated) |
| Broche 2 | I/O — User I/O pin |
| Broche 3 | I/O — User I/O pin |
| Broche 4 | I/O — User I/O pin |
| Broche 5 | I/O — User I/O pin |
| Broche 6 | I/O — User I/O pin |
| Broche 7 | I/O — User I/O pin |
| Broche 8 | I/O — User I/O pin |
| Broche 9 | I/O — User I/O pin |
| Broche 10 | I/O — User I/O pin |
| Broche 11 | I/O — User I/O pin |
| Broche 12 | I/O — User I/O pin |
| Broche 13 | I/O — User I/O pin |
| Broche 14 | GND — Ground |
| Broche 15 | I/O — User I/O pin |
| Broche 16 | I/O — User I/O pin |
| Broche 17 | I/O — User I/O pin |
| Broche 18 | I/O — User I/O pin |
| Broche 19 | I/O — User I/O pin |
| Broche 20 | I/O — User I/O pin |
| Broche 21 | I/O — User I/O pin |
| Broche 22 | I/O — User I/O pin |
| Broche 23 | I/O — User I/O pin |
| Broche 24 | I/O — User I/O pin |
| Broche 25 | GND — Ground |
| Broche 26 | I/O — User I/O pin |
| Broche 27 | I/O — User I/O pin |
| Broche 28 | I/O — User I/O pin |
| Broche 29 | I/O — User I/O pin |
| Broche 30 | I/O — User I/O pin |
| Broche 31 | I/O — User I/O pin |
| Broche 32 | I/O — User I/O pin |
| Broche 33 | I/O — User I/O pin |
| Broche 34 | I/O — User I/O pin |
| Broche 35 | I/O — User I/O pin |
| Broche 36 | I/O — User I/O pin |
| Broche 37 | I/O — User I/O pin |
| Broche 38 | GND — Ground |
| Broche 39 | I/O — User I/O pin |
| Broche 40 | I/O — User I/O pin |
| Broche 41 | I/O — User I/O pin |
| Broche 42 | I/O — User I/O pin |
| Broche 43 | I/O — User I/O pin |
| Broche 44 | I/O — User I/O pin |
| Broche 45 | I/O — User I/O pin |
| Broche 46 | I/O — User I/O pin |
| Broche 47 | I/O — User I/O pin |
| Broche 48 | TDI — JTAG Test Data In |
| Broche 49 | TMS — JTAG Test Mode Select |
| Broche 50 | TCK — JTAG Test Clock |
| Broche 51 | GND — Ground |
| Broche 52 | I/O — User I/O pin |
| Broche 53 | I/O — User I/O pin |
| Broche 54 | I/O — User I/O pin |
| Broche 55 | I/O — User I/O pin |
| Broche 56 | I/O — User I/O pin |
| Broche 57 | I/O — User I/O pin |
| Broche 58 | I/O — User I/O pin |
| Broche 59 | I/O — User I/O pin |
| Broche 60 | I/O — User I/O pin |
| Broche 61 | I/O — User I/O pin |
| Broche 62 | I/O — User I/O pin |
| Broche 63 | GND — Ground |
| Broche 64 | I/O — User I/O pin |
| Broche 65 | I/O — User I/O pin |
| Broche 66 | I/O — User I/O pin |
| Broche 67 | I/O — User I/O pin |
| Broche 68 | I/O — User I/O pin |
| Broche 69 | I/O — User I/O pin |
| Broche 70 | I/O — User I/O pin |
| Broche 71 | I/O — User I/O pin |
| Broche 72 | I/O — User I/O pin |
| Broche 73 | I/O — User I/O pin |
| Broche 74 | I/O — User I/O pin |
| Broche 75 | I/O — User I/O pin |
| Broche 76 | GND — Ground |
| Broche 77 | I/O — User I/O pin |
| Broche 78 | I/O — User I/O pin |
| Broche 79 | I/O — User I/O pin |
| Broche 80 | I/O — User I/O pin |
| Broche 81 | I/O — User I/O pin |
| Broche 82 | I/O — User I/O pin |
| Broche 83 | I/O — User I/O pin |
| Broche 84 | I/O — User I/O pin |
| Broche 85 | I/O — User I/O pin |
| Broche 86 | I/O — User I/O pin |
| Broche 87 | I/O — User I/O pin |
| Broche 88 | I/O — User I/O pin |
| Broche 89 | GND — Ground |
| Broche 90 | I/O — User I/O pin |
| Broche 91 | I/O — User I/O pin |
| Broche 92 | I/O — User I/O pin |
| Broche 93 | I/O — User I/O pin |
| Broche 94 | I/O — User I/O pin |
| Broche 95 | I/O — User I/O pin |
| Broche 96 | I/O — User I/O pin |
| Broche 97 | I/O — User I/O pin |
| Broche 98 | I/O — User I/O pin |
| Broche 99 | TDO — JTAG Test Data Out |
| Broche 100 | VCC — +5 V core supply |
Applications typiques
EPM7128STC100-15N convient pour 6 applications: Microcontroller I/O Expansion and Bus Decoding, Peripheral Glue Logic and Interface Bridging, State Machine and Industrial Control Logic, LED Multiplexing and Display Driving, Legacy 74LS / 74HC Logic Replacement, Instant-On Boot and Configuration Memory Replacement.
Microcontroller I/O Expansion and Bus Decoding
The EPM7128STC100-15N is a natural fit for microcontroller I/O expansion and bus decoding because its 128 macro cells and 84 user I/O pins can decode large address windows and generate multiple chip-select signals in a single device. The 15 ns pin-to-pin delay matches the timing budget of an 8-bit or 16-bit MCU running at 33 MHz, ensuring that the CPLD output settles within one clock period after the address bus changes. With 5 V VCCIO tolerance, the part can be interfaced directly to legacy 5 V peripherals without level-shifters, reducing BOM cost and board area. Designers typically implement address latch, chip-select decoding, and wait-state generation in one EPM7128, replacing multiple discrete 74LS138/74LS139 decoders and 74LS373 latches. The non-volatile EEPROM configuration boots in microseconds, so there is no FPGA-style configuration delay - critical for deterministic interrupt latency in motor-control or industrial-automation firmware.
Recommandé
Peripheral Glue Logic and Interface Bridging
The EPM7128STC100-15N's deterministic timing and 5 V I/O make it ideal for interface-bridging glue logic between processors, memory, and peripherals operating at different voltages. A common use case is bridging a 5 V MCU to a 3.3 V SD card or NOR flash, where the CPLD's programmable VCCIO bank can be split into one 5 V bank and one 3.3 V bank - eliminating external level-shifters. The 15 ns tPD adds only one extra clock of latency at 66 MHz, which is acceptable for SPI, I2C, or parallel-memory interfaces. The 84 user I/Os are sufficient to implement a full 16-bit address bus, 16-bit data bus, and 8-10 control signals in a single device, leaving macro cells available for handshake logic. Designers also appreciate that the JTAG ISP allows field-upgradeable firmware fixes without desoldering the part.
Recommandé
State Machine and Industrial Control Logic
For industrial control, the EPM7128STC100-15N's -15 ns delay, 76.9 MHz internal toggle rate, and EEPROM-based non-volatile configuration deliver the determinism and reliability required for safety-critical state machines. Each macro cell contains a flip-flop, so a single device can implement several independent FSMs such as a packaging-machine sequencer, conveyor controller, or HVAC state controller. The 5 V tolerant I/O interfaces directly to 24 V industrial sensors and actuators through external optocouplers, avoiding the level-shifting required by 3.3 V FPGAs. The MAX 7000S family's instant-on configuration (microseconds, not milliseconds) is critical for fail-safe startup where any boot delay could cause process malfunction. Programming via JTAG also lets engineers perform in-circuit firmware revisions without removing boards from production equipment.
Recommandé
LED Multiplexing and Display Driving
The EPM7128STC100-15N's 84 user I/Os are well-suited for driving large LED matrices, 7-segment displays, and character LCDs where many discrete signals must be time-multiplexed. A single EPM7128 can scan a 64-LED matrix, an 8-digit 7-segment display, or a 4-line character LCD without any additional drivers. The 76.9 MHz internal toggle rate ensures flicker-free refresh rates above 100 Hz even for large displays, while the 15 ns tPD ensures clean column-to-column transitions. The 5 V I/O can directly drive common-anode or common-cathode LED arrays without buffer transistors, reducing board complexity. Designers also use the JTAG ISP to change display patterns or timing parameters without re-spinning hardware - a major advantage for prototype and small-batch production.
Recommandé
Legacy 74LS / 74HC Logic Replacement
The EPM7128STC100-15N is frequently used to replace multiple discrete 74LS, 74HC, or 74HCT logic ICs on legacy PCBs where board area is constrained. A single EPM7128 can absorb up to 128 macro cells of glue logic - equivalent to 8-12 small-scale integration (SSI) packages - reducing both component count and assembly cost. The -15 ns tPD is comparable to a 74LS153 multiplexer or 74LS138 decoder, so existing timing margins are preserved. The 5 V VCCIO tolerance is pin-compatible with TTL and CMOS legacy logic rails, simplifying migration. This application is especially common in industrial and aerospace systems that must be re-spun to reduce obsolete-discrete-logic risk without redesigning the board footprint.
Recommandé
Instant-On Boot and Configuration Memory Replacement
The EPM7128STC100-15N's EEPROM-based configuration cell provides microsecond-class instant-on, which is faster than any SRAM-based FPGA boot PROM. Designers use this property for power-critical applications such as automotive body controllers, security panels, and emergency-stop controllers where any boot delay is unacceptable. The 128 macro cells are sufficient to implement both the boot logic and the steady-state functionality in one device, eliminating a separate configuration memory chip. The JTAG ISP supports in-the-field firmware updates, so the same hardware can be reprogrammed across product variants - a major simplification for low-volume, high-mix production. Per the Altera datasheet, the configuration EEPROM retains the bitstream indefinitely without power, supporting decades of shelf life.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EPM7128STC100-15N — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EPM7128STC100-15 | EPM7128STC100-10N | EPM7128SQC100-10N | EPM7128SQC100-15 |
|---|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) |
| Package | 100-pin TQFP | 100-pin TQFP (same) | 100-pin TQFP (same) | 100-pin TQFP (same) | 100-pin TQFP (same) |
| Family / Sub-family | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S |
| Pin-to-Pin Delay (tPD) | 15 ns | 15 ns (identical) | 10 ns (-33%) | 10 ns (-33%) | 15 ns (identical) |
| Macro Cells | 128 | 128 (identical) | 128 (identical) | 128 (identical) | 128 (identical) |
| Maximum Internal Frequency | 76.9 MHz | 76.9 MHz (identical) | 100 MHz (+30%) | 100 MHz (+30%) | 76.9 MHz (identical) |
| Usable Gates | 2,500 | 2,500 (identical) | 2,500 (identical) | 2,500 (identical) | 2,500 (identical) |
| User I/O Pins | 84 | 84 (identical) | 84 (identical) | 84 (identical) | 84 (identical) |
| Lead-Free Finish | Yes (Pb-free suffix 'N') | No (SnPb standard) | Yes (Pb-free) | Yes (Pb-free, PQFP) | No (SnPb, PQFP) |
| Operating Temperature | 0C to +70C (commercial) | 0C to +70C | 0C to +70C | 0C to +70C | 0C to +70C |
Principaux différenciateurs
- Instant-on non-volatile EEPROM configuration (microseconds) (vs EPM7128SQC100-10N)
- Same-die drop-in availability in PQFP finish (EPM7128SQC100-10N) (vs EPM7128STC100-15)
- 128 macro cells / 84 I/Os in single 100-pin TQFP (vs EPM7128SLC84-10)
Notes de conception
Estimated: at VCC = 5 V and all 84 I/Os toggling at 76.9 MHz into 50 pF loads, the EPM7128STC100-15N consumes approximately 250-400 mA of dynamic supply current plus 5-10 mA of static current. Designers should provide a 100 nF decoupling capacitor within 5 mm of each VCC pin (the 100-pin TQFP has multiple VCC pins distributed around the package). Per the Altera datasheet, unused I/O pins must be programmed as outputs driving ground to minimize switching current; leaving them floating can increase supply current by 30-50 mA.
Route all four JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 100 ohm series-termination resistors near the driving CPLD. Keep JTAG traces at least 3 mm away from clock traces to avoid coupling that can corrupt ISP programming. The exposed thermal pad of the 100-pin TQFP must be soldered to a copper pour of at least 1 square inch to keep junction temperature below 125 C at full toggle rate. Per the Altera datasheet, the VCCIO pins (5 V or 3.3 V) must be applied before VCC during power-up to prevent I/O latch-up.
Do not assume the EPM7128STC100-15N is in production - it was discontinued in June 2017 per the Altera PDN. Source from franchised distributors only (DigiKey, Mouser, Arrow) or from authorized secondary-market specialists. Verify that the JTAG chain order matches your schematic when chaining multiple EPM7xxx devices, because the MAX 7000S family uses a fixed 10-bit JTAG instruction register length. When migrating to MAX II / MAX V for new designs, plan for pinout differences and recompile all design files - the new families use a different BSDL boundary-scan description.
Informations de conformité
Per the Altera datasheet, the EPM7128STC100-15N ships with a standard SnPb finish (non-lead-free). It is not AEC-Q100 qualified. RoHS-compliant variants are the EPM7128STC100-10N, EPM7128SQC100-10N, and EPM7128SQC100-7N (lead-free finishes).