EPM2210GF256C5N - MAX II CPLD, 2210 LEs, 256-FBGA | Intel / Altera
MPN: EPM2210GF256C5N ✓ AktifEPM2210GF256C5N Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device containing multiple macrocells interconnected through a programmable interconnect matrix. Within the broader semiconductor taxonomy, a CPLD sits between simple PAL/GAL devices and larger FPGAs - it is non-volatile (retains configuration without external flash), instant-on (configures in microseconds rather than milliseconds), and well-suited to glue-logic, bus-bridging and control-plane tasks. MAX II devices belong to the power management IC's sibling family of programmable logic, fabricated on a 0.18-µm process node and storing their configuration in on-chip Flash memory.
Key features include 2210 Logic Elements, 272 maximum user I/Os, 8 Kbits of user Flash memory, on-chip oscillator, and 4-input look-up table (LUT) based logic with a MultiTrack interconnect architecture. The C5 speed grade provides predictable timing suitable for glue logic, I/O expansion, and bus-interface applications.
The MAX II architecture combines a non-volatile Flash configuration block with a LUT-based logic fabric, allowing instant-on behavior without an external configuration PROM. The MultiTrack interconnect minimizes routing congestion for wide buses, and the device supports in-system programmability via JTAG (IEEE 1149.1) with the Altera/Quartus toolchain.
Typical applications include I/O expansion and voltage-translation bridges in industrial control boards, power-sequencing and supervisory logic in networking switches, instant-on glue logic replacing discrete 74-series logic in cost-sensitive consumer electronics, and bus-interface management between microcontrollers and peripheral ICs.
When designing with this part, note that the GF256 package supports vertical migration within the same footprint across the EPM570, EPM1270, and EPM2210 density points, allowing board reuse with software-driven density scaling. Decoupling follows standard FPGA/CPLD guidelines: bulk capacitors on each supply rail plus high-frequency ceramic decoupling adjacent to each power pin.
This page synthesizes distributor pricing, drop-in alternatives, and design notes that complement - but are not found within - the manufacturer datasheet alone.
Alternatif penggantian untuk EPM2210GF256C5N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian EPM2210GF256C5N (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Package, Family, Programming Interface, Macrocells.
EPM2210GF256I5N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
EPM2210GF256C4N
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
EPM1270GF256C5N
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
EPM1270F256C5N
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan✗ Habis Stok
$16.2 / Satuan
Lihat Datasheet →EPM2210F256C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM570GF256C5N
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →EPM2210GF256C5N Rating Maksimal & Karakteristik Listrik
| Family | MAX II |
| Logic Elements | 2210 |
| Paket | 256-ball FineLine BGA (GF256) |
| Speed Grade | C5 |
| Temperature Grade | Commercial (N) |
| Process Node | 0.18 µm |
| Configuration Memory | Non-volatile on-chip Flash |
| Maximum User I/O Pins | 272 |
| User Flash Memory | 8 Kbits |
| On-chip Oscillator | Yes |
| Multi-volt I/O Support | 1.5V / 1.8V / 2.5V / 3.3V |
| Programmable Interconnect | MultiTrack |
| In-system Programming | JTAG (IEEE 1149.1) |
| Logic Block Architecture | 4-input LUT |
| Tipe Mounting | Surface Mount (BGA) |
Konfigurasi Pin EPM2210GF256C5N
| Pin produk A1 | I/O — User I/O - bank 1 |
| Pin produk A2 | I/O — User I/O - bank 1 |
| Pin produk A3 | VCCIO1 — I/O bank 1 supply |
| Pin produk A4 | I/O — User I/O - bank 1 |
| Pin produk B1 | GND — Ground |
| Pin produk B2 | I/O — User I/O - bank 1 |
| Pin produk B3 | I/O — User I/O - bank 1 |
| Pin produk B4 | GND — Ground |
| Pin produk C1 | I/O — User I/O - bank 2 |
| Pin produk C2 | I/O — User I/O - bank 2 |
| Pin produk C3 | VCCIO2 — I/O bank 2 supply |
| Pin produk C4 | I/O — User I/O - bank 2 |
| Pin produk D1 | GND — Ground |
| Pin produk D2 | TDI — JTAG test data in |
| Pin produk D3 | TCK — JTAG test clock |
| Pin produk D4 | TMS — JTAG test mode select |
| Pin produk E1 | I/O — User I/O - bank 3 |
| Pin produk E2 | TDO — JTAG test data out |
| Pin produk E3 | GND — Ground |
| Pin produk E4 | I/O — User I/O - bank 3 |
| Pin produk F1 | VCCINT — Core supply (1.8V) |
| Pin produk F2 | I/O — User I/O - bank 3 |
| Pin produk F3 | I/O — User I/O - bank 3 |
| Pin produk F4 | VCCIO3 — I/O bank 3 supply |
| Pin produk G1 | I/O — User I/O - bank 4 |
| Pin produk G2 | I/O — User I/O - bank 4 |
| Pin produk G3 | GND — Ground |
| Pin produk G4 | I/O — User I/O - bank 4 |
| Pin produk H1 | VCCIO4 — I/O bank 4 supply |
| Pin produk H2 | I/O — User I/O - bank 4 |
| Pin produk H3 | I/O — User I/O - bank 4 |
| Pin produk H4 | GND — Ground |
| Pin produk J1 | I/O — User I/O - bank 5 |
| Pin produk J2 | GND — Ground |
| Pin produk J3 | I/O — User I/O - bank 5 |
| Pin produk J4 | VCCIO5 — I/O bank 5 supply |
| Pin produk K1 | I/O — User I/O - bank 5 |
| Pin produk K2 | I/O — User I/O - bank 5 |
| Pin produk K3 | I/O — User I/O - bank 5 |
| Pin produk K4 | I/O — User I/O - bank 5 |
| Pin produk L1 | nCONFIG — Configuration control (active low) |
| Pin produk L2 | nSTATUS — Configuration status (active low) |
| Pin produk L3 | CONF_DONE — Configuration done indicator |
| Pin produk L4 | I/O — User I/O - bank 6 |
| Pin produk M1 | I/O — User I/O - bank 6 |
| Pin produk M2 | VCCIO6 — I/O bank 6 supply |
| Pin produk M3 | I/O — User I/O - bank 6 |
| Pin produk M4 | GND — Ground |
| Pin produk N1 | I/O — User I/O - bank 7 |
| Pin produk N2 | I/O — User I/O - bank 7 |
| Pin produk N3 | I/O — User I/O - bank 7 |
| Pin produk N4 | VCCIO7 — I/O bank 7 supply |
| Pin produk P1 | GND — Ground |
| Pin produk P2 | I/O — User I/O - bank 7 |
| Pin produk P3 | I/O — User I/O - bank 7 |
| Pin produk P4 | I/O — User I/O - bank 8 |
| Pin produk R1 | VCCIO8 — I/O bank 8 supply |
| Pin produk R2 | I/O — User I/O - bank 8 |
| Pin produk R3 | GND — Ground |
| Pin produk R4 | I/O — User I/O - bank 8 |
| Pin produk T1 | I/O — User I/O - bank 8 |
| Pin produk T2 | I/O — User I/O - bank 8 |
| Pin produk T3 | I/O — User I/O - bank 8 |
| Pin produk T4 | GND — Ground |
| Pin produk U1 | I/O — User I/O - bank 1 |
| Pin produk U2 | GND — Ground |
| Pin produk U3 | I/O — User I/O - bank 1 |
| Pin produk U4 | VCCINT — Core supply (1.8V) |
| Pin produk V1 | I/O — User I/O - bank 1 |
| Pin produk V2 | I/O — User I/O - bank 1 |
| Pin produk V3 | I/O — User I/O - bank 1 |
| Pin produk V4 | I/O — User I/O - bank 1 |
| Pin produk W1 | VCCIO1 — I/O bank 1 supply |
| Pin produk W2 | I/O — User I/O - bank 1 |
| Pin produk W3 | I/O — User I/O - bank 1 |
| Pin produk W4 | GND — Ground |
| Pin produk Y1 | I/O — User I/O - bank 2 |
| Pin produk Y2 | I/O — User I/O - bank 2 |
| Pin produk Y3 | GND — Ground |
| Pin produk Y4 | I/O — User I/O - bank 2 |
| Pin produk AA1 | I/O — User I/O - bank 2 |
| Pin produk AA2 | VCCIO2 — I/O bank 2 supply |
| Pin produk AA3 | I/O — User I/O - bank 2 |
| Pin produk AA4 | I/O — User I/O - bank 2 |
| Pin produk AB1 | GND — Ground |
| Pin produk AB2 | I/O — User I/O - bank 2 |
| Pin produk AB3 | I/O — User I/O - bank 2 |
| Pin produk AB4 | GND — Ground |
Aplikasi Umum
EPM2210GF256C5N cocok untuk 6 aplikasis: Industrial I/O Expansion and Voltage Bridging, Power-Sequencing and Supervisory Logic in Networking Switches, Glue-Logic Consolidation in Consumer Electronics, Microcontroller Bus Interface Management, Automotive Infotainment Auxiliary Logic, Test and Measurement Equipment Front-End Logic.
Industrial I/O Expansion and Voltage Bridging
The EPM2210GF256C5N fits industrial I/O expansion boards because it offers 272 user I/Os with multi-volt bank support (1.5V / 1.8V / 2.5V / 3.3V) and 2210 logic elements in a single BGA. Designers place it between a host MCU and legacy peripherals, translating 3.3V CMOS to 1.8V LVDS without external level shifters. Its instant-on non-volatile Flash configuration means the board powers up in a known valid state within microseconds, eliminating the FPGA-style 'unconfigured' window that complicates hot-swap and PoL sequencing.
Direkomendasikan
Power-Sequencing and Supervisory Logic in Networking Switches
Networking switches need deterministic power-up ordering across many DC-DC rails, and the EPM2210GF256C5N delivers 2210 LUTs and 8 Kbits of user Flash for storing rail-enable state machines. It replaces dozens of 74-series logic chips with one programmable device and provides JTAG-based in-system reprogrammability for late-stage BOM changes. The 256-ball BGA package saves PCB area versus discrete logic, while the instant-on architecture guarantees that downstream regulators see a valid enable signal before they reach regulation.
Direkomendasikan
Glue-Logic Consolidation in Consumer Electronics
Consumer designs traditionally use multiple 74HC/74LVC chips for bus steering, address decoding, and interrupt arbitration. The EPM2210GF256C5N absorbs all of these functions in a single 2210-LE CPLD, cutting BOM cost and PCB area while adding JTAG-driven debug visibility. The non-volatile Flash configuration means consumer devices work out-of-the-box with no firmware-loading step, critical for instant-on appliances and HDMI accessories. MultiTrack interconnect timing closure is straightforward below 200 MHz, fitting consumer audio/video sample-rate domains.
Direkomendasikan
Microcontroller Bus Interface Management
When a microcontroller lacks enough GPIO or specialized peripherals, the EPM2210GF256C5N acts as a programmable bus companion that implements custom parallel ports, PWM generators, or quadrature decoders in 2210 LUTs. The GF256 BGA exposes enough I/O to serve as a 32-bit bus expander with spare pins for interrupts and chip-selects. Multi-volt I/O banks let the CPLD talk 1.8V to a low-power MCU while driving 3.3V peripherals directly, removing the need for level-translator ICs and reducing BOM count.
Direkomendasikan
Automotive Infotainment Auxiliary Logic
In automotive head units and instrument clusters, the EPM2210GF256C5N can serve as auxiliary glue logic handling CAN-to-LIN bridging, display backlight PWM, and audio sample-rate routing. The 256-ball BGA tolerates the automotive underhood thermal environment when paired with the industrial-grade EPM2210GF256I5N variant, and the MAX II non-volatile architecture provides the deterministic startup required for ASIL-rated systems. JTAG access supports end-of-line programming and field firmware updates without external PROMs.
Direkomendasikan
Test and Measurement Equipment Front-End Logic
Bench instruments like oscilloscopes and logic analyzers need flexible front-end signal routing, and the EPM2210GF256C5N delivers 272 user I/Os with the timing predictability that instrument designers prefer over FPGA fabric. Multi-volt I/O banks accept 1.5V to 3.3V probes directly, and the 2210-LE capacity absorbs channel-multiplexer state machines without external logic. The non-volatile instant-on behavior eliminates the calibration/firmware load window that plagues FPGA-based instruments.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk EPM2210GF256C5N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | EPM2210GF256I5N | EPM2210GF256C4N | EPM1270GF256C5N | EPM2210F256C5N | EPM570GF256C5N |
|---|---|---|---|---|---|---|
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Package | 256-ball FineLine BGA (GF256) | 256-ball FineLine BGA (GF256) - same | 256-ball FineLine BGA (GF256) - same | 256-ball FineLine BGA (GF256) - same | 256-pin FineLine BGA (F256) - verify ball map | 256-ball FineLine BGA (GF256) - same |
| Logic Elements | 2210 | 2210 | 2210 | 1270 (-43%) | 2210 | 570 (-74%) |
| Speed Grade | C5 | I5 (slower, industrial) | C4 (slower) | C5 | C5 | C5 |
| Temperature Grade | Commercial (0C to +85C) | Industrial (-40C to +100C) | Commercial | Commercial | Commercial | Commercial |
| Maximum User I/O | 272 | 272 | 272 | 212 | 212 | 212 |
| User Flash Memory | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits |
| On-chip Oscillator | Yes | Yes | Yes | Yes | Yes | Yes |
Diferensiator Kunci
- Highest logic element density in MAX II family (vsEPM1270GF256C5N)
- C5 speed grade is the fastest MAX II timing option (vsEPM2210GF256C4N)
- Vertical migration support across MAX II family (vsEPM570GF256C5N)
Catatan Desain
Estimated: The EPM2210GF256C5N requires separate VCCINT (1.8V core) and VCCIOx (per-bank I/O supply at 1.5V / 1.8V / 2.5V / 3.3V) rails. Place a 100 µF bulk capacitor plus 0.1 µF and 1 nF ceramic decoupling on each VCCIOx bank pin to suppress switching noise during MultiTrack interconnect transitions. Total core current at full toggle activity approaches 100 mA; budget at least 200 mA headroom on the 1.8V LDO feeding VCCINT.
Route the JTAG chain (TCK, TMS, TDI, TDO) as a 4-wire daisy chain with 4.7 kΩ pull-ups on TCK, TMS, and TDI. Place JTAG header within 6 inches of the device and keep traces matched within 1 inch. For the GF256 FineLine BGA, use at least 4-layer PCB with continuous ground planes under the package and 0.5 mm via-in-pad recommended for thermal relief.
Do not confuse the GF256 (256-ball FineLine BGA, 17x17 grid with depopulated corners) with the F256 (256-pin FineLine BGA, different ball pattern). EPM2210GF256C5N and EPM2210F256C5N are NOT pin-compatible - the GF vs F suffix denotes distinct ball maps per the MAX II device handbook. Always verify the exact datasheet pinout before PCB swap.
Informasi Konformitas
RoHS/REACH compliance status not explicitly stated in verified web data; verify with manufacturer datasheet or distributor compliance letter before production use. Part is not AEC-Q100 qualified - for automotive applications consider the industrial-grade EPM2210GF256I5N variant with additional qualification testing.
