EPM2210GF256C5N - MAX II CPLD, 2210 LEs, 256-FBGA | Intel / Altera
MPN: EPM2210GF256C5N ✓ Hoạt độngEPM2210GF256C5N Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device containing multiple macrocells interconnected through a programmable interconnect matrix. Within the broader semiconductor taxonomy, a CPLD sits between simple PAL/GAL devices and larger FPGAs - it is non-volatile (retains configuration without external flash), instant-on (configures in microseconds rather than milliseconds), and well-suited to glue-logic, bus-bridging and control-plane tasks. MAX II devices belong to the power management IC's sibling family of programmable logic, fabricated on a 0.18-µm process node and storing their configuration in on-chip Flash memory.
Key features include 2210 Logic Elements, 272 maximum user I/Os, 8 Kbits of user Flash memory, on-chip oscillator, and 4-input look-up table (LUT) based logic with a MultiTrack interconnect architecture. The C5 speed grade provides predictable timing suitable for glue logic, I/O expansion, and bus-interface applications.
The MAX II architecture combines a non-volatile Flash configuration block with a LUT-based logic fabric, allowing instant-on behavior without an external configuration PROM. The MultiTrack interconnect minimizes routing congestion for wide buses, and the device supports in-system programmability via JTAG (IEEE 1149.1) with the Altera/Quartus toolchain.
Typical applications include I/O expansion and voltage-translation bridges in industrial control boards, power-sequencing and supervisory logic in networking switches, instant-on glue logic replacing discrete 74-series logic in cost-sensitive consumer electronics, and bus-interface management between microcontrollers and peripheral ICs.
When designing with this part, note that the GF256 package supports vertical migration within the same footprint across the EPM570, EPM1270, and EPM2210 density points, allowing board reuse with software-driven density scaling. Decoupling follows standard FPGA/CPLD guidelines: bulk capacitors on each supply rail plus high-frequency ceramic decoupling adjacent to each power pin.
This page synthesizes distributor pricing, drop-in alternatives, and design notes that complement - but are not found within - the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho EPM2210GF256C5N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPM2210GF256C5N (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Package, Family, Programming Interface, Macrocells.
EPM2210GF256I5N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM2210GF256C4N
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
EPM1270GF256C5N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM1270F256C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM2210F256C5N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM570GF256C5N
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EPM2210GF256C5N Tỷ lệ tối đa & tính chất điện
| Family | MAX II |
| Logic Elements | 2210 |
| Hộp | 256-ball FineLine BGA (GF256) |
| Speed Grade | C5 |
| Temperature Grade | Commercial (N) |
| Process Node | 0.18 µm |
| Configuration Memory | Non-volatile on-chip Flash |
| Maximum User I/O Pins | 272 |
| User Flash Memory | 8 Kbits |
| On-chip Oscillator | Yes |
| Multi-volt I/O Support | 1.5V / 1.8V / 2.5V / 3.3V |
| Programmable Interconnect | MultiTrack |
| In-system Programming | JTAG (IEEE 1149.1) |
| Logic Block Architecture | 4-input LUT |
| Kiểu lắp đặt | Surface Mount (BGA) |
Cấu hình chân EPM2210GF256C5N
| Chân A1 | I/O — User I/O - bank 1 |
| Chân A2 | I/O — User I/O - bank 1 |
| Chân A3 | VCCIO1 — I/O bank 1 supply |
| Chân A4 | I/O — User I/O - bank 1 |
| Chân B1 | GND — Ground |
| Chân B2 | I/O — User I/O - bank 1 |
| Chân B3 | I/O — User I/O - bank 1 |
| Chân B4 | GND — Ground |
| Chân C1 | I/O — User I/O - bank 2 |
| Chân C2 | I/O — User I/O - bank 2 |
| Chân C3 | VCCIO2 — I/O bank 2 supply |
| Chân C4 | I/O — User I/O - bank 2 |
| Chân D1 | GND — Ground |
| Chân D2 | TDI — JTAG test data in |
| Chân D3 | TCK — JTAG test clock |
| Chân D4 | TMS — JTAG test mode select |
| Chân E1 | I/O — User I/O - bank 3 |
| Chân E2 | TDO — JTAG test data out |
| Chân E3 | GND — Ground |
| Chân E4 | I/O — User I/O - bank 3 |
| Chân F1 | VCCINT — Core supply (1.8V) |
| Chân F2 | I/O — User I/O - bank 3 |
| Chân F3 | I/O — User I/O - bank 3 |
| Chân F4 | VCCIO3 — I/O bank 3 supply |
| Chân G1 | I/O — User I/O - bank 4 |
| Chân G2 | I/O — User I/O - bank 4 |
| Chân G3 | GND — Ground |
| Chân G4 | I/O — User I/O - bank 4 |
| Chân H1 | VCCIO4 — I/O bank 4 supply |
| Chân H2 | I/O — User I/O - bank 4 |
| Chân H3 | I/O — User I/O - bank 4 |
| Chân H4 | GND — Ground |
| Chân J1 | I/O — User I/O - bank 5 |
| Chân J2 | GND — Ground |
| Chân J3 | I/O — User I/O - bank 5 |
| Chân J4 | VCCIO5 — I/O bank 5 supply |
| Chân K1 | I/O — User I/O - bank 5 |
| Chân K2 | I/O — User I/O - bank 5 |
| Chân K3 | I/O — User I/O - bank 5 |
| Chân K4 | I/O — User I/O - bank 5 |
| Chân L1 | nCONFIG — Configuration control (active low) |
| Chân L2 | nSTATUS — Configuration status (active low) |
| Chân L3 | CONF_DONE — Configuration done indicator |
| Chân L4 | I/O — User I/O - bank 6 |
| Chân M1 | I/O — User I/O - bank 6 |
| Chân M2 | VCCIO6 — I/O bank 6 supply |
| Chân M3 | I/O — User I/O - bank 6 |
| Chân M4 | GND — Ground |
| Chân N1 | I/O — User I/O - bank 7 |
| Chân N2 | I/O — User I/O - bank 7 |
| Chân N3 | I/O — User I/O - bank 7 |
| Chân N4 | VCCIO7 — I/O bank 7 supply |
| Chân P1 | GND — Ground |
| Chân P2 | I/O — User I/O - bank 7 |
| Chân P3 | I/O — User I/O - bank 7 |
| Chân P4 | I/O — User I/O - bank 8 |
| Chân R1 | VCCIO8 — I/O bank 8 supply |
| Chân R2 | I/O — User I/O - bank 8 |
| Chân R3 | GND — Ground |
| Chân R4 | I/O — User I/O - bank 8 |
| Chân T1 | I/O — User I/O - bank 8 |
| Chân T2 | I/O — User I/O - bank 8 |
| Chân T3 | I/O — User I/O - bank 8 |
| Chân T4 | GND — Ground |
| Chân U1 | I/O — User I/O - bank 1 |
| Chân U2 | GND — Ground |
| Chân U3 | I/O — User I/O - bank 1 |
| Chân U4 | VCCINT — Core supply (1.8V) |
| Chân V1 | I/O — User I/O - bank 1 |
| Chân V2 | I/O — User I/O - bank 1 |
| Chân V3 | I/O — User I/O - bank 1 |
| Chân V4 | I/O — User I/O - bank 1 |
| Chân W1 | VCCIO1 — I/O bank 1 supply |
| Chân W2 | I/O — User I/O - bank 1 |
| Chân W3 | I/O — User I/O - bank 1 |
| Chân W4 | GND — Ground |
| Chân Y1 | I/O — User I/O - bank 2 |
| Chân Y2 | I/O — User I/O - bank 2 |
| Chân Y3 | GND — Ground |
| Chân Y4 | I/O — User I/O - bank 2 |
| Chân AA1 | I/O — User I/O - bank 2 |
| Chân AA2 | VCCIO2 — I/O bank 2 supply |
| Chân AA3 | I/O — User I/O - bank 2 |
| Chân AA4 | I/O — User I/O - bank 2 |
| Chân AB1 | GND — Ground |
| Chân AB2 | I/O — User I/O - bank 2 |
| Chân AB3 | I/O — User I/O - bank 2 |
| Chân AB4 | GND — Ground |
Ứng dụng tiêu biểu
EPM2210GF256C5N phù hợp cho 6 Áp dụngs: Industrial I/O Expansion and Voltage Bridging, Power-Sequencing and Supervisory Logic in Networking Switches, Glue-Logic Consolidation in Consumer Electronics, Microcontroller Bus Interface Management, Automotive Infotainment Auxiliary Logic, Test and Measurement Equipment Front-End Logic.
Industrial I/O Expansion and Voltage Bridging
The EPM2210GF256C5N fits industrial I/O expansion boards because it offers 272 user I/Os with multi-volt bank support (1.5V / 1.8V / 2.5V / 3.3V) and 2210 logic elements in a single BGA. Designers place it between a host MCU and legacy peripherals, translating 3.3V CMOS to 1.8V LVDS without external level shifters. Its instant-on non-volatile Flash configuration means the board powers up in a known valid state within microseconds, eliminating the FPGA-style 'unconfigured' window that complicates hot-swap and PoL sequencing.
Được đề xuất
Power-Sequencing and Supervisory Logic in Networking Switches
Networking switches need deterministic power-up ordering across many DC-DC rails, and the EPM2210GF256C5N delivers 2210 LUTs and 8 Kbits of user Flash for storing rail-enable state machines. It replaces dozens of 74-series logic chips with one programmable device and provides JTAG-based in-system reprogrammability for late-stage BOM changes. The 256-ball BGA package saves PCB area versus discrete logic, while the instant-on architecture guarantees that downstream regulators see a valid enable signal before they reach regulation.
Được đề xuất
Glue-Logic Consolidation in Consumer Electronics
Consumer designs traditionally use multiple 74HC/74LVC chips for bus steering, address decoding, and interrupt arbitration. The EPM2210GF256C5N absorbs all of these functions in a single 2210-LE CPLD, cutting BOM cost and PCB area while adding JTAG-driven debug visibility. The non-volatile Flash configuration means consumer devices work out-of-the-box with no firmware-loading step, critical for instant-on appliances and HDMI accessories. MultiTrack interconnect timing closure is straightforward below 200 MHz, fitting consumer audio/video sample-rate domains.
Được đề xuất
Microcontroller Bus Interface Management
When a microcontroller lacks enough GPIO or specialized peripherals, the EPM2210GF256C5N acts as a programmable bus companion that implements custom parallel ports, PWM generators, or quadrature decoders in 2210 LUTs. The GF256 BGA exposes enough I/O to serve as a 32-bit bus expander with spare pins for interrupts and chip-selects. Multi-volt I/O banks let the CPLD talk 1.8V to a low-power MCU while driving 3.3V peripherals directly, removing the need for level-translator ICs and reducing BOM count.
Được đề xuất
Automotive Infotainment Auxiliary Logic
In automotive head units and instrument clusters, the EPM2210GF256C5N can serve as auxiliary glue logic handling CAN-to-LIN bridging, display backlight PWM, and audio sample-rate routing. The 256-ball BGA tolerates the automotive underhood thermal environment when paired with the industrial-grade EPM2210GF256I5N variant, and the MAX II non-volatile architecture provides the deterministic startup required for ASIL-rated systems. JTAG access supports end-of-line programming and field firmware updates without external PROMs.
Được đề xuất
Test and Measurement Equipment Front-End Logic
Bench instruments like oscilloscopes and logic analyzers need flexible front-end signal routing, and the EPM2210GF256C5N delivers 272 user I/Os with the timing predictability that instrument designers prefer over FPGA fabric. Multi-volt I/O banks accept 1.5V to 3.3V probes directly, and the 2210-LE capacity absorbs channel-multiplexer state machines without external logic. The non-volatile instant-on behavior eliminates the calibration/firmware load window that plagues FPGA-based instruments.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPM2210GF256C5N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPM2210GF256I5N | EPM2210GF256C4N | EPM1270GF256C5N | EPM2210F256C5N | EPM570GF256C5N |
|---|---|---|---|---|---|---|
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Package | 256-ball FineLine BGA (GF256) | 256-ball FineLine BGA (GF256) - same | 256-ball FineLine BGA (GF256) - same | 256-ball FineLine BGA (GF256) - same | 256-pin FineLine BGA (F256) - verify ball map | 256-ball FineLine BGA (GF256) - same |
| Logic Elements | 2210 | 2210 | 2210 | 1270 (-43%) | 2210 | 570 (-74%) |
| Speed Grade | C5 | I5 (slower, industrial) | C4 (slower) | C5 | C5 | C5 |
| Temperature Grade | Commercial (0C to +85C) | Industrial (-40C to +100C) | Commercial | Commercial | Commercial | Commercial |
| Maximum User I/O | 272 | 272 | 272 | 212 | 212 | 212 |
| User Flash Memory | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits |
| On-chip Oscillator | Yes | Yes | Yes | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- Highest logic element density in MAX II family (vsEPM1270GF256C5N)
- C5 speed grade is the fastest MAX II timing option (vsEPM2210GF256C4N)
- Vertical migration support across MAX II family (vsEPM570GF256C5N)
Ghi chú thiết kế
Estimated: The EPM2210GF256C5N requires separate VCCINT (1.8V core) and VCCIOx (per-bank I/O supply at 1.5V / 1.8V / 2.5V / 3.3V) rails. Place a 100 µF bulk capacitor plus 0.1 µF and 1 nF ceramic decoupling on each VCCIOx bank pin to suppress switching noise during MultiTrack interconnect transitions. Total core current at full toggle activity approaches 100 mA; budget at least 200 mA headroom on the 1.8V LDO feeding VCCINT.
Route the JTAG chain (TCK, TMS, TDI, TDO) as a 4-wire daisy chain with 4.7 kΩ pull-ups on TCK, TMS, and TDI. Place JTAG header within 6 inches of the device and keep traces matched within 1 inch. For the GF256 FineLine BGA, use at least 4-layer PCB with continuous ground planes under the package and 0.5 mm via-in-pad recommended for thermal relief.
Do not confuse the GF256 (256-ball FineLine BGA, 17x17 grid with depopulated corners) with the F256 (256-pin FineLine BGA, different ball pattern). EPM2210GF256C5N and EPM2210F256C5N are NOT pin-compatible - the GF vs F suffix denotes distinct ball maps per the MAX II device handbook. Always verify the exact datasheet pinout before PCB swap.
Thông tin tuân thủ
RoHS/REACH compliance status not explicitly stated in verified web data; verify with manufacturer datasheet or distributor compliance letter before production use. Part is not AEC-Q100 qualified - for automotive applications consider the industrial-grade EPM2210GF256I5N variant with additional qualification testing.
