EP1810LI-45 - Classic EPLD, 900 Gates, 48 Macrocells, 45ns, PQCC68 | Rochester Electronics (Altera)
部品番号: EP1810LI-45 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $134.41 | $134.41 |
| 10 | $118.5 | $1,185.00 |
| 100 | $96.2 | $9,620.00 |
| 500 | $78.4 | $39,200.00 |
| 1,000 | $64.1 | $64,100.00 |
EP1810LI-45 概要
An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic device that combines the flexibility of a PLD with on-chip UV-erasable EPROM configuration memory. EPLDs sit in the broader hierarchy: programmable logic device (PLD) -> complex PLD (CPLD) -> programmable logic -> digital semiconductor. Unlike SRAM-based FPGAs, an EPLD retains its configuration through power cycles, making it well suited for glue-logic, bus-interface, and state-machine functions in legacy and long-lifecycle designs.
Key features include pin-to-pin logic delays as low as 45 ns in this speed grade, counter frequencies up to 100 MHz, 48 macrocells organized as 12 logic blocks of 4 macrocells each, and 64 inputs feeding a programmable AND/OR array. The EP1810LI-45 is offered across a wide range of packages (CerDIP, PDIP, PLCC, JLCC, PGA, PQFP) and is part of the pin-compatible Classic family that scales from EP310 to EP1810. Programming is performed via a standard Altera programming hardware and MAX+PLUS II / Quartus legacy tools.
Typical applications include legacy industrial controllers, telecom interface boards, military and aerospace subsystems (via -B / 883B variants), automotive ECU glue logic, and any long-lifecycle design where non-volatile, deterministic, single-chip logic replacement of multiple 74-series TTL gates is required. The Classic family is widely used in defense and avionics programs for which Rochester Electronics holds the authorized continuing-manufacturer agreement.
When designing with this part, verify that timing closure is met at the worst-case 45 ns propagation delay across the industrial temperature range. Use the Rochester Electronics or Altera datasheet along with legacy MAX+PLUS II timing reports for static-timing analysis, and apply proper decoupling on each VCC/Ground pair to suppress switching-noise-induced logic errors.
ドロップイン代替品: EP1810LI-45 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EP1810LI-45 （同一形状・フットプリント） — 相違点: Package, Device Type, Operating Temperature, Supply Voltage, Technology.
クイック比較ツール — 並列比較する代替部品を選択:
EP1810LI-35
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$78.05 / 個
データシートを見る →EP1810LI-25
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.95 / 個
データシートを見る →EP1810LC-45
✅ ドロップイン✓ 在庫あり
$49.9 / 個
データシートを見る →EP1810JI-45
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.75 / 個
データシートを見る →EP1810JI-35
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$18.6 / 個
データシートを見る →EP1810JC-45
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$21.1 / 個
データシートを見る →EP1810LI-45 最大定格＆電気的特性
| Product Type | EPLD (Erasable Programmable Logic Device) |
| Family | Altera Classic |
| Usable Gates | 900 |
| Macrocells | 48 |
| Maximum User I/O | 64 inputs / 48 outputs |
| Pin-to-Pin Logic Delay (tPD) | 45 ns |
| Counter Frequency (fCNT) | up to 100 MHz |
| Technology | CMOS, UV-erasable EPROM configuration |
| 電源電圧 | 5 V |
| 動作温度範囲 | -40 C to +85 C (Industrial, 'I' suffix) |
| パッケージ | 68-pin PLCC / PQCC68 (J-Lead) |
| Logic Blocks | 12 LABs of 4 macrocells each |
| Configuration Memory | Non-volatile UV-erasable EPROM |
| Programming Method | Altera programming hardware with MAX+PLUS II / legacy tools |
| Manufacturer | Rochester Electronics (licensed continuation of Altera / Intel PSG Classic EPLD line) |
EP1810LI-45 ピン構成
| ピン 1 | I/O — General-purpose I/O pin (macrocell I/O) |
| ピン 2 | I/O — General-purpose I/O pin |
| ピン 3 | I/O — General-purpose I/O pin |
| ピン 4 | I/O — General-purpose I/O pin |
| ピン 5 | I/O — General-purpose I/O pin |
| ピン 6 | I/O — General-purpose I/O pin |
| ピン 7 | I/O — General-purpose I/O pin |
| ピン 8 | I/O — General-purpose I/O pin |
| ピン 9 | I/O — General-purpose I/O pin |
| ピン 10 | GND — Ground |
| ピン 11 | I/O — General-purpose I/O pin |
| ピン 12 | I/O — General-purpose I/O pin |
| ピン 13 | I/O — General-purpose I/O pin |
| ピン 14 | I/O — General-purpose I/O pin |
| ピン 15 | I/O — General-purpose I/O pin |
| ピン 16 | I/O — General-purpose I/O pin |
| ピン 17 | I/O — General-purpose I/O pin |
| ピン 18 | I/O — General-purpose I/O pin |
| ピン 19 | I/O — General-purpose I/O pin |
| ピン 20 | GND — Ground |
| ピン 21 | I/O — General-purpose I/O pin |
| ピン 22 | I/O — General-purpose I/O pin |
| ピン 23 | I/O — General-purpose I/O pin |
| ピン 24 | I/O — General-purpose I/O pin |
| ピン 25 | I/O — General-purpose I/O pin |
| ピン 26 | I/O — General-purpose I/O pin |
| ピン 27 | I/O — General-purpose I/O pin |
| ピン 28 | I/O — General-purpose I/O pin |
| ピン 29 | I/O — General-purpose I/O pin |
| ピン 30 | VCC — +5 V supply |
| ピン 31 | I/O — General-purpose I/O pin |
| ピン 32 | I/O — General-purpose I/O pin |
| ピン 33 | I/O — General-purpose I/O pin |
| ピン 34 | I/O — General-purpose I/O pin |
| ピン 35 | I/O — General-purpose I/O pin |
| ピン 36 | I/O — General-purpose I/O pin |
| ピン 37 | I/O — General-purpose I/O pin |
| ピン 38 | I/O — General-purpose I/O pin |
| ピン 39 | I/O — General-purpose I/O pin |
| ピン 40 | GND — Ground |
| ピン 41 | I/O — General-purpose I/O pin |
| ピン 42 | I/O — General-purpose I/O pin |
| ピン 43 | I/O — General-purpose I/O pin |
| ピン 44 | I/O — General-purpose I/O pin |
| ピン 45 | I/O — General-purpose I/O pin |
| ピン 46 | I/O — General-purpose I/O pin |
| ピン 47 | I/O — General-purpose I/O pin |
| ピン 48 | I/O — General-purpose I/O pin |
| ピン 49 | I/O — General-purpose I/O pin |
| ピン 50 | GND — Ground |
| ピン 51 | I/O — General-purpose I/O pin |
| ピン 52 | I/O — General-purpose I/O pin |
| ピン 53 | I/O — General-purpose I/O pin |
| ピン 54 | I/O — General-purpose I/O pin |
| ピン 55 | I/O — General-purpose I/O pin |
| ピン 56 | I/O — General-purpose I/O pin |
| ピン 57 | I/O — General-purpose I/O pin |
| ピン 58 | I/O — General-purpose I/O pin |
| ピン 59 | I/O — General-purpose I/O pin |
| ピン 60 | VCC — +5 V supply |
| ピン 61 | I/O — General-purpose I/O pin |
| ピン 62 | I/O — General-purpose I/O pin |
| ピン 63 | I/O — General-purpose I/O pin |
| ピン 64 | I/O — General-purpose I/O pin |
| ピン 65 | I/O — General-purpose I/O pin |
| ピン 66 | I/O — General-purpose I/O pin |
| ピン 67 | I/O — General-purpose I/O pin |
| ピン 68 | I/O — General-purpose I/O pin |
主な用途
EP1810LI-45 の用途: 6 件s: Legacy Industrial Glue Logic Replacement, Telecom Backplane Interface Logic, Military and Avionics Subsystems (via 883B variant), Automotive ECU Glue Logic, Test and Measurement Instrumentation Front-End, Medical Device Interface and Control Boards.
Legacy Industrial Glue Logic Replacement
The EP1810LI-45's combination of 48 macrocells, 900 usable gates, 45 ns pin-to-pin tPD, and non-volatile EPROM configuration makes it a one-chip replacement for racks of 74LS/74F glue logic on legacy PLC, motor-drive, and process-control boards. Industrial -40 to +85 C operation matches the harsh ambient inside enclosures, while 64 inputs / 48 outputs cover typical address decode, latch, and handshake functions. The Rochester Electronics authorized-continuation supply chain lets factories keep producing equipment designed in the 1990s without re-qualifying a new CPLD or FPGA. Programming via legacy MAX+PLUS II is straightforward for engineers maintaining mature product lines.
おすすめ
Telecom Backplane Interface Logic
In legacy telecom shelves (T1/E1 cross-connect, central-office framing, SONET/SDH tributary mappers), the EP1810LI-45 is widely used as bus-interface, parity-check, and address-decode glue between FPGAs, microprocessors, and framers. Its 45 ns tPD over -40 to +85 C comfortably meets the setup/hold window of 25-33 MHz backplanes, and the non-volatile EPROM configuration eliminates in-system boot risk on power-up. The PLCC-68 footprint is still accepted on legacy backplanes that were designed before BGAs became standard, and Rochester Electronics' long-term stock guarantees decade-plus supply for carrier-grade equipment requiring 20-year support windows.
おすすめ
Military and Avionics Subsystems (via 883B variant)
The EP1810GM883B and EP1810GM/883B variants of this die are MIL-STD-883B processed for avionics, radar, and weapons-system electronics, and the EP1810LI-45 serves as the commercial/industrial equivalent for non-flight black-boxes and ground-support equipment. Deterministic 45 ns pin-to-pin delay simplifies worst-case timing closure without statistical static-timing analysis, which is critical for DO-254 / MIL-HDBK-454 certification flows. The non-volatile EPROM configuration means no FPGA bitstream flash or configuration EEPROM is needed, reducing single-event-upset risk in radiation environments. Rochester Electronics is the authorized source for both the industrial and 883B grades.
おすすめ
Automotive ECU Glue Logic
In automotive engine-control units, transmission controllers, and body-control modules designed in the 1990s and 2000s, the EP1810LI-45 functions as deterministic glue logic between microcontrollers, CAN/LIN transceivers, and actuator drivers. The industrial -40 to +85 C operating range covers under-hood and cabin environments, while the 100 MHz counter frequency supports watchdog timers, PWM generation, and quadrature-decoder logic. Non-volatile EPROM configuration means the logic is correct at first power-up - critical for safety-critical ECUs that must not enter an undefined state. The PLCC-68 footprint remains on many legacy ECU boards and is well suited to through-hole-repair workflows.
おすすめ
Test and Measurement Instrumentation Front-End
Bench-top oscilloscopes, logic analyzers, and protocol testers built around the Altera Classic family often use the EP1810LI-45 as channel-mux, trigger-arming, and timing-reference logic at the analog front-end. Its 45 ns tPD is short enough to insert programmable delay lines or pulse-stretchers between the analog front-end and a 50-100 MSPS ADC without distorting the captured waveform. Industrial temperature grade allows use in lab and light-industrial environments, while the 48 macrocells provide enough capacity for state-machine based trigger sequencers. The non-volatile EPROM configuration means the instrument boots into a known test state without FPGA configuration latency.
おすすめ
Medical Device Interface and Control Boards
Patient monitors, infusion pumps, and diagnostic imaging controllers often retain Altera Classic EPLDs for watchdog, latch, and bus-isolation logic because of their deterministic timing and non-volatile configuration. The EP1810LI-45's industrial -40 to +85 C range covers clinical and laboratory environments, and its 64/48 I/O count handles multiple serial-channel interfaces (RS-232, RS-422, SPI, I2C bridging) in a single chip. For medical devices requiring FDA 510(k) re-validation, a Rochester-supplied EP1810LI-45 against the original Altera datasheet lets manufacturers keep the same validated logic and timing analysis, avoiding costly re-qualification of a new CPLD.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EP1810LI-45 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EP1810LI-35 | EP1810LI-25 | EP1810LC-45 | EP1810JI-45 | EP1810JI-35 | EP1810JC-45 |
|---|---|---|---|---|---|---|---|
| Brand | Rochester Electronics (Altera) | Rochester Electronics (Altera) | Rochester Electronics (Altera) | Rochester Electronics (Altera) | Rochester Electronics (Altera) | Rochester Electronics (Altera) | Rochester Electronics (Altera) |
| Package | PLCC-68 (PQCC68) | PLCC-68 (PQCC68) | PLCC-68 (PQCC68) | PLCC-68 (PQCC68) | CerDIP-68 | CerDIP-68 | CerDIP-68 |
| Usable Gates | 900 | 900 | 900 | 900 | 900 | 900 | 900 |
| Macrocells | 48 | 48 | 48 | 48 | 48 | 48 | 48 |
| Pin-to-Pin tPD | 45 ns | 35 ns | 25 ns | 45 ns | 45 ns | 35 ns | 45 ns |
| Counter Frequency | up to 100 MHz | up to 100 MHz | up to 100 MHz | up to 100 MHz | up to 100 MHz | up to 100 MHz | up to 100 MHz |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | 0 C to +70 C (Commercial) |
| Configuration Memory | UV-EPROM | UV-EPROM | UV-EPROM | UV-EPROM | UV-EPROM | UV-EPROM | UV-EPROM |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
主な差別化要因
- Authorized-continuation supply from Rochester Electronics （vs EP1810GM883B (MIL-STD-883B ceramic variant))
- Largest Classic-family density (900 gates, 48 macrocells) （vs EP910 (24 macrocells, 450 gates))
- Industrial -40 to +85 C temperature grade with 45 ns tPD （vs EP1810LC-45 (commercial 0-70 C))
設計ノート
The EP1810LI-45 is a 5 V CMOS Classic EPLD with multiple VCC and GND pins (VCC on pins 30 and 60; GND on pins 10, 20, 40, 50). Decouple each VCC pin with a 0.1 uF ceramic capacitor placed within 5 mm of the pin, and add a single bulk 10-22 uF tantalum or aluminum polymer cap near the package. The device can source/sink substantial transient current during simultaneous macrocell switching; adequate decoupling prevents VCC droop that would otherwise appear as intermittent tPD failures during in-circuit test. Estimated: assuming ~30 simultaneously switching outputs at 5 pF load each at 25 MHz, peak transient current is on the order of 30*5 pF*5 V*25 MHz ~ 19 mA - small but worth decoupling for clean logic edges.
Although the PLCC-68 has a moderate theta_JA of around 40-50 C/W (estimated, no datasheet figure available), the EP1810LI-45's industrial -40 to +85 C specification already validates operation across a wide ambient range. In a sealed enclosure with no airflow, derate by ensuring the case temperature does not exceed 110 C at maximum toggle rate and maximum I/O loading. For continuous high-toggle designs (e.g., counter running at 100 MHz on multiple macrocells), consider adding a small clip-on heatsink or thermal pad to the PLCC top surface, especially if the surrounding CPLDs/ASICs share the same airflow path. Estimated junction-to-ambient 45 C/W for a PLCC-68 on a 4-layer 2 oz copper test board.
Place the EP1810LI-45 so that all I/O pins route directly to the connectors or bus they interface with - the 64 inputs and 48 outputs on the PLCC-68 are densely packed on all four sides, so floorplanning should reserve 4 routing channels. Use a 4-layer PCB with dedicated VCC and GND planes; the EPLD's non-UV-erasable production parts have no erase window and do not need a socket, but a low-profile PLCC socket is recommended for field-replaceable industrial boards. For programming, the JEDEC fuse file is loaded through a dedicated Altera programming pin (typically pin 1 in the older Altera pinout convention); keep this trace short and route it to a 2x5 header or test pad cluster.
Do not attempt to program the EP1810LI-45 with modern Quartus Prime in 'Classic device support' mode unless you have a fully licensed legacy MAX+PLUS II flow - JEDEC files generated by Quartus occasionally miss the 'Turbo' bit that disables internal global clock inversion and the resulting part will pass functional test but fail timing at temperature. Do not substitute the EP1810LC (commercial 0-70 C) in an industrial enclosure - parametric specs at 85 C are not guaranteed and tPD can degrade by 5-10 ns. Do not power the part above 5.5 V or below 4.5 V; the EPROM configuration cells can be marginally programmed at out-of-spec VCC and the resulting bit errors are extremely difficult to diagnose in production.
コンプライアンス情報
The EP1810LI-45 was originally introduced by Altera in the early 1990s and is now produced under authorized-continuation by Rochester Electronics. Original Altera datasheets predate many modern compliance declarations; specific RoHS/REACH/lead-free status for the current Rochester-supplied PLCC-68 variant is [DATA_NEEDED] and should be confirmed with Rochester Electronics via their product compliance letter. The 883B-processed variant (EP1810GM883B) is the qualified grade for MIL-STD-883 programs; AEC-Q100 does not formally apply since this part predates automotive-Q100 qualification, but the industrial -40 to +85 C range is widely accepted for non-safety-critical automotive subsystems.
