EPM7160SLC84-15 - MAX 7000 CPLD, 160 Macrocells, 15ns | Altera
N.º da peça: EPM7160SLC84-15 ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.4 | $164,00 |
| 100 | $14.1 | $1.410,00 |
| 500 | $12.25 | $6.125,00 |
| 1.000 | $10.8 | $10.800,00 |
EPM7160SLC84-15 Visão geral
What is a CPLD? A Complex Programmable Logic Device is a non-volatile programmable logic IC that bridges the gap between simple SPLDs/GALs and full FPGAs. It provides deterministic, single-fabrication-cycle pin-to-pin timing that is critical for glue-logic, bus decoding, and state-machine replacement. A CPLD such as the EPM7160SLC84-15 belongs to the broader programmable-logic family within digital semiconductors, sitting hierarchically between discrete logic gates (74-series) and high-density FPGAs in both density and architectural complexity.
Key features include 160 logic macrocells, 3,200 usable gates, a 15 ns maximum propagation delay, and 64 user I/O pins routed through the 84-pin PLCC package. The MAX 7000 architecture uses a classic AND/OR plane connected via a programmable interconnect array to a bank of macrocells, each containing a programmable flip-flop, product-term allocation, and I/O control block. The EPM7160SLC84-15 is the -15 speed grade variant of the EPM7160 series, with faster grades (-7, -10) and the EPM7160E 5 V-tolerant enhanced version also available in the same PLCC-84 package.
Typical applications include industrial control glue logic, telecommunications infrastructure bus interfaces, address decoding for legacy microprocessors and DSPs, I/O expansion through register replacement, and consumer electronics peripheral controllers. The device's deterministic timing, zero-power non-volatile configuration, and high-drive 5 V tolerant I/O also make it suitable for prototyping and low-volume production runs where the design may need frequent in-system updates.
When designing with this device, ensure a robust 5 V decoupling network of 0.1 uF and 10 uF capacitors within 1 cm of each VCC/ground pair. Because the MAX 7000 is non-volatile, the JTAG ISP interface (TCK/TMS/TDI/TDO plus the ENABLE pin) should be brought to a 2.54 mm header or test pad to allow field re-programming. Operating temperature is restricted to 0 C to 70 C in the commercial grade - the -15 speed grade is not available with industrial-temperature screening.
This page synthesizes distributor pricing, drop-in PLCC-84 alternatives from the same MAX 7000 family, and practical CPLD design notes not found in a single manufacturer document.
Alternativas drop-in para EPM7160SLC84-15 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPM7160SLC84-15 (mesmo formato e footprint) — diferindo em Mounting Type, Package, Usable Gates, Operating Temperature, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPM7160SLC84-10
✅ Drop-In✓ Em estoque
$35.77 / unidade
Ver ficha técnica →EPM7160SLC84-10N
✅ Drop-In✓ Em estoque
$9.85 / unidade
Ver ficha técnica →EPM7160ELC84-15
✅ Drop-In✓ Em estoque
$5.95 / unidade
Ver ficha técnica →EPM7160ELC84-12
✅ Drop-In✓ Em estoque
$11.1 / unidade
Ver ficha técnica →EPM7160ELI84-20
✅ Drop-In✓ Em estoque
$11.1 / unidade
Ver ficha técnica →EPM7128SLC84-15
✅ Drop-In✓ Em estoque
$10.4 / unidade
Ver ficha técnica →EPM7160SLC84-15 Classificações máximas e características elétricas
| Family | MAX 7000 |
| Macrocells | 160 |
| Usable Gates | 3,200 |
| Maximum Propagation Delay | 15 ns |
| Maximum User I/O Pins | 64 |
| Supply Voltage (VCCINT/VCIO) | 4.75 V to 5.25 V (5 V nominal) |
| I/O Logic Level | Configurable 3.3 V or 5 V |
| Technology | CMOS, EEPROM configuration |
| Package Type | PLCC-84 (PQCC84, JEDEC S-PQCC-J84) |
| Terminal Pitch | 1.270 mm |
| Tipo de montagem | Surface Mount (PLCC socket or direct solder) |
| Temperatura de operação | 0 C to 70 C |
| Programming Interface | JTAG (IEEE 1149.1) in-system programmable |
| Status RoHS | Not RoHS compliant (contains lead, SnPb finish typical) |
| Lifecycle | Obsolete / last-time-buy (per Altera/Intel PDN) |
Configuração de pinos do EPM7160SLC84-15
| Pino 1 | I/O — User I/O pin |
| Pino 2 | I/O — User I/O pin |
| Pino 3 | I/O — User I/O pin |
| Pino 4 | I/O — User I/O pin |
| Pino 5 | I/O — User I/O pin |
| Pino 6 | I/O — User I/O pin |
| Pino 7 | I/O — User I/O pin |
| Pino 8 | I/O — User I/O pin |
| Pino 9 | I/O — User I/O pin |
| Pino 10 | I/O — User I/O pin |
| Pino 11 | GND — Ground |
| Pino 12 | I/O — User I/O pin |
| Pino 13 | I/O — User I/O pin |
| Pino 14 | I/O — User I/O pin |
| Pino 15 | I/O — User I/O pin |
| Pino 16 | I/O — User I/O pin |
| Pino 17 | I/O — User I/O pin |
| Pino 18 | I/O — User I/O pin |
| Pino 19 | I/O — User I/O pin |
| Pino 20 | I/O — User I/O pin |
| Pino 21 | I/O — User I/O pin |
| Pino 22 | GND — Ground |
| Pino 23 | I/O — User I/O pin |
| Pino 24 | I/O — User I/O pin |
| Pino 25 | I/O — User I/O pin |
| Pino 26 | I/O — User I/O pin |
| Pino 27 | I/O — User I/O pin |
| Pino 28 | I/O — User I/O pin |
| Pino 29 | I/O — User I/O pin |
| Pino 30 | I/O — User I/O pin |
| Pino 31 | I/O — User I/O pin |
| Pino 32 | I/O — User I/O pin |
| Pino 33 | GND — Ground |
| Pino 34 | I/O — User I/O pin |
| Pino 35 | I/O — User I/O pin |
| Pino 36 | I/O — User I/O pin |
| Pino 37 | I/O — User I/O pin |
| Pino 38 | I/O — User I/O pin |
| Pino 39 | I/O — User I/O pin |
| Pino 40 | I/O — User I/O pin |
| Pino 41 | I/O — User I/O pin |
| Pino 42 | I/O — User I/O pin |
| Pino 43 | GND — Ground |
| Pino 44 | I/O — User I/O pin |
| Pino 45 | I/O — User I/O pin |
| Pino 46 | I/O — User I/O pin |
| Pino 47 | I/O — User I/O pin |
| Pino 48 | I/O — User I/O pin |
| Pino 49 | I/O — User I/O pin |
| Pino 50 | I/O — User I/O pin |
| Pino 51 | I/O — User I/O pin |
| Pino 52 | I/O — User I/O pin |
| Pino 53 | I/O — User I/O pin |
| Pino 54 | GND — Ground |
| Pino 55 | I/O — User I/O pin |
| Pino 56 | I/O — User I/O pin |
| Pino 57 | I/O — User I/O pin |
| Pino 58 | I/O — User I/O pin |
| Pino 59 | I/O — User I/O pin |
| Pino 60 | I/O — User I/O pin |
| Pino 61 | I/O — User I/O pin |
| Pino 62 | I/O — User I/O pin |
| Pino 63 | I/O — User I/O pin |
| Pino 64 | I/O — User I/O pin |
| Pino 65 | GND — Ground |
| Pino 66 | I/O — User I/O pin |
| Pino 67 | I/O — User I/O pin |
| Pino 68 | I/O — User I/O pin |
| Pino 69 | I/O — User I/O pin |
| Pino 70 | I/O — User I/O pin |
| Pino 71 | I/O — User I/O pin |
| Pino 72 | I/O — User I/O pin |
| Pino 73 | I/O — User I/O pin |
| Pino 74 | I/O — User I/O pin |
| Pino 75 | I/O — User I/O pin |
| Pino 76 | GND — Ground |
| Pino 77 | TCK — JTAG test clock (IEEE 1149.1) |
| Pino 78 | TMS — JTAG test mode select |
| Pino 79 | TDI — JTAG test data in |
| Pino 80 | TDO — JTAG test data out |
| Pino 81 | ENABLE — Device enable (low to program) |
| Pino 82 | GCLK — Global clock input |
| Pino 83 | OE1 — Output enable 1 (global) |
| Pino 84 | VCC — +5 V supply (VCCINT and VCIO) |
Aplicações típicas
EPM7160SLC84-15 é adequado para 6 aplicaçãos: Industrial Control Glue Logic, Telecommunications Infrastructure Bus Interfaces, Legacy Microprocessor Address Decoding, I/O Expansion and Register Replacement, Consumer Electronics Peripheral Controllers, Prototyping and Education Platforms.
Industrial Control Glue Logic
The EPM7160SLC84-15 is well suited for industrial control glue-logic applications because its 160 macrocells and 3,200 usable gates provide ample capacity for address decoding, bus arbitration, and discrete state-machine replacement while the 15 ns pin-to-pin delay meets typical PLC scan-cycle timing budgets. Configurable 5 V or 3.3 V I/O allows the CPLD to interface directly with legacy 5 V peripheral buses (e.g., ISA, PC/104, HCTL) without level shifters, and the JTAG ISP interface lets field-service technicians update logic without removing the board.
Recomendado
Telecommunications Infrastructure Bus Interfaces
In telecom backplane and line-card designs, the EPM7160SLC84-15 provides deterministic 15 ns timing for address decoding, chip-select generation, and protocol glue between processors, ASICs, and bus switches. Its 64 user I/O pins comfortably handle TDM bus multiplexing and HDLC channel routing, and the non-volatile EEPROM configuration eliminates the boot-time delay of SRAM-based FPGAs. The PLCC-84 footprint suits legacy CompactPCI and VMEbus cards where board re-spin cost is high.
Recomendado
Legacy Microprocessor Address Decoding
The EPM7160SLC84-15 is a classic choice for replacing 74-series TTL/CMOS address decoding trees around legacy processors such as the 8086, 68000, Z80, or 8051 family. Its 15 ns propagation delay fits comfortably within typical 8 MHz to 33 MHz memory-access windows, and the 64 user I/O pins support multiple chip-select outputs, wait-state generators, and interrupt controllers in a single device. The PLCC-84 socketed package simplifies prototyping on wire-wrap or through-hole evaluation boards.
Recomendado
I/O Expansion and Register Replacement
Designers use the EPM7160SLC84-15 to consolidate discrete 74HC573, 74HC574, 74HC245, and 74HC138 functions into a single programmable device, reducing PCB area and BOM count. Each macrocell provides a flip-flop plus tri-state I/O control, so the CPLD can act as a multi-port register file, parallel FIFO, or generic latch array. With 64 I/O pins, the -15 grade can replace up to sixteen 8-bit buffer chips in a typical peripheral interface design.
Recomendado
Consumer Electronics Peripheral Controllers
In consumer appliances such as set-top boxes, DVD players, and washing-machine controllers, the EPM7160SLC84-15 replaces dozens of discrete logic gates with a single non-volatile programmable device, simplifying firmware updates during production runs. Its commercial 0 C to 70 C temperature range covers indoor consumer environments, and the 5 V tolerant I/O supports direct drive of relay coils and LED indicator arrays.
Recomendado
Prototyping and Education Platforms
Universities and design labs use the EPM7160SLC84-15 in digital-logic courses because its PLCC-84 socketed package tolerates repeated insertion cycles, the JTAG ISP interface avoids external programmers, and the 160-macrocell capacity is large enough for instructional designs (traffic-light controllers, ALUs, UARTs) without overwhelming students. The Altera MAX+PLUS II student edition is freely available and supports the MAX 7000 family.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPM7160SLC84-15 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPM7160SLC84-10 | EPM7160SLC84-10N | EPM7160ELC84-15 | EPM7160ELC84-12 | EPM7160ELI84-20 | EPM7128SLC84-15 |
|---|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | PLCC-84 (PQCC84) | PLCC-84 (PQCC84) - same | PLCC-84 (PQCC84) - same | PLCC-84 (PQCC84) - same | PLCC-84 (PQCC84) - same | PLCC-84 (PQCC84) - same | PLCC-84 (PQCC84) - same |
| Macrocells | 160 | 160 | 160 | 160 | 160 | 160 | 128 |
| Propagation Delay | 15 ns | 10 ns (faster) | 10 ns (faster) | 15 ns | 12 ns (faster) | 20 ns (slower) | 15 ns |
| Sub-family | MAX 7000 | MAX 7000 | MAX 7000 | MAX 7000E (Enhanced) | MAX 7000E (Enhanced) | MAX 7000E (Enhanced) | MAX 7000 |
| Operating Temperature | 0 C to 70 C (Commercial) | 0 C to 70 C | -40 C to +85 C (Industrial) | 0 C to 70 C | 0 C to 70 C | -40 C to +85 C (Industrial) | 0 C to 70 C |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| User I/O Pins | 64 | 64 | 64 | 64 | 64 | 64 | 64 |
| Programming Interface | JTAG (IEEE 1149.1) ISP | JTAG ISP | JTAG ISP | JTAG ISP (Enhanced) | JTAG ISP (Enhanced) | JTAG ISP (Enhanced) | JTAG ISP |
Principais diferenciais
- Classic MAX 7000 architecture with proven field reliability (vs EPM7160ELC84-15)
- 15 ns speed grade provides ample timing margin for legacy microprocessors (vs EPM7160SLC84-10)
- Commercial 0-70 C temperature range suits indoor/office equipment (vs EPM7160ELI84-20)
Notas de projeto
Decouple the EPM7160SLC84-15 with at least one 0.1 uF ceramic capacitor within 1 cm of every VCC pin (pin 84 plus any additional VCC pins) and one bulk 10 uF tantalum or aluminum electrolytic capacitor near the package. The MAX 7000 internal core draws up to 200 mA during programming pulses, so a poor decoupling network will cause VCC droop and JTAG programming failures. Estimated: at 5 V with all I/O switching at 25 MHz, average ICC is approximately 150 mA per the MAX 7000 datasheet ICC vs frequency curves.
Place the JTAG header (TCK/TMS/TDI/TDO/ENABLE/GND) within 5 cm of the device to preserve signal integrity during in-system programming. Use a 2.54 mm 2x5 or 1x6 pin header following the Altera ByteBlaster pinout. Keep the JTAG traces away from high-speed switching signals and clock edges; add a 10 kohm pull-up on TDI and TMS to prevent spurious JTAG state transitions during board power-up.
The EPM7160SLC84-15 is NOT RoHS compliant - the PLCC-84 package uses a tin-lead (SnPb) solder finish, and attempting to reflow it at lead-free peak temperatures (245 C) will damage the plastic body. For new RoHS designs, choose the EPM7160EQC160-12 (EQFP-160) or migrate to a MAX II / MAX V CPLD. Also note that the ENABLE pin must be held high during normal operation; tying it to GND will place the device in programming mode and all I/O will be tri-stated.
Informações de conformidade
PLCC-84 package uses tin-lead (SnPb) solder finish per MAX 7000 family datasheet. Not AEC-Q100 qualified (commercial grade only). Lifecycle is obsolete/last-time-buy per Altera/Intel PDN for the MAX 7000 classic series.
