Товары (44.000+)

ISL33002IUZ - I2C Bus Buffer 2-Channel Hot-Swap | Renesas
ISL33002IUZ

ISL33002IUZ - I2C Bus Buffer 2-Channel Hot-Swap | Renesas

The Renesas Electronics ISL33002IUZ is a two-channel I2C bus buffer with rise-time accelerators and hot-swap capability, operating from 2.5V, 3.3V or 5V supplies in an 8-pin MSOP (MSOP-8) package rated for the industrial temperature range of -40C to +85C. An I2C bus buffer (also called an I2C repeater, bus accelerator, or signal buffer) is an interface IC inserted in series with the SDA and SCL lines of a two-wire serial bus. The I2C specification limits direct bus capacitance to 400 pF; beyond this, rise times become too slow for reliable communication. A bus buffer segments the bus, isolating capacitance on either side and allowing the total system to far exceed the 400 pF limit while keeping the bidirectional, open-drain, clock-stretching behavior intact. Key features of the ISL33002 include two buffered channels (SDA and SCL), rise-time accelerator circuitry that reduces the pull-up power consumption of passive resistors and improves achievable data rate, and integrated hot-swap circuitry that prevents bus corruption when a card or module is inserted or removed while the backplane is powered. The device is I2C and SMBus compatible and supports clock stretching and multi-master bus arbitration on both SDA and SCL, according to the Renesas ISL33001/ISL33002/ISL33003 datasheet. Architecturally, the ISL33002 uses level-sensitive bidirectional buffer stages on each channel with current-limited accelerator pull-up events, so the buffer drives rise edges faster than large resistive pull-ups can, without fighting open-drain low-level assertions. This preserves true open-drain signaling while cutting RC time constants on heavily loaded segments. Typical applications include backplane I2C fan-out in servers and telecom shelves, hot-swappable line cards and caddies, long cable I2C links between enclosures, and power-management (PMBus/SMBus) networks in industrial systems. The industrial -40C to +85C rating of the IUZ suffix suits uncooled factory environments. A key design consideration: the hot-swap function needs the BIAS/EN pin properly connected to the local supply and the correct external pull-up values to avoid lockup during power sequencing. This page synthesizes distributor pricing, stock status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
ISL4241EIRZ - 3V RS-232 3TX/5RX Transceiver, ±15kV ESD | Renesas
ISL4241EIRZ

ISL4241EIRZ - 3V RS-232 3TX/5RX Transceiver, ±15kV ESD | Renesas

The Renesas ISL4241EIRZ is a 2.7V to 5.5V powered RS-232 transceiver with three transmitters and five receivers (3Tx/5Rx), housed in a 32-pin QFN (5x5 mm) package. It supports data rates up to 250 kbps, delivers ±15 kV IEC 61000-4-2 ESD protection on the RS-232 pins, and draws a 10 nA low-power shutdown current when disabled. The device meets EIA/TIA-232 and V.28/V.24 specifications even at VCC = 3.0 V, making it suitable for both 3.3V and 5V designs. A line driver/receiver (RS-232 transceiver) is a type of interface IC that converts TTL/CMOS logic levels (0V/3.3V) on the controller side to the bipolar ±5V to ±15V signal levels required by the EIA/TIA-232 standard on the cable side. Modern RS-232 transceivers integrate one or more charge-pump DC-DC converters so they can generate the necessary RS-232 voltages from a single 3V to 5V supply, eliminating the legacy ±12V rails. They sit in the interface hierarchy: physical-layer transceiver -> serial interface IC -> wired connectivity IC, and are commonly classified under the broader category of UART/LIN/serial transceivers. Key features include 3 transmitters and 5 receivers in a single IC (vs. the more common 3Tx/3Rx or 1Tx/1Rx), on-board charge pumps that require only four 0.1 µF external capacitors, and a SHDN pin that drops quiescent current to 10 nA for battery-powered designs. The wide supply range (2.7V–5.5V) simplifies designs migrating between 3.3V-only microcontrollers and legacy 5V systems. The QFN-32 (5x5) package with an exposed pad provides a low thermal resistance path suitable for industrial temperature ranges from -40°C to +85°C. The ISL4241EIRZ is engineered around a regulated dual charge pump and an on-chip high-efficiency DC-DC converter that produces the positive and negative RS-232 rails from a single supply. Each transmitter is rated for ±15 kV ESD (HBM and IEC 61000-4-2 air-gap), which removes the need for external TVS diodes on the DB-9 connector. The part is targeted at PDAs, palmtops, notebook/laptop computers, and any design that requires an extra receiver for monitoring ring-indicate or carrier-detect signals without adding a second transceiver. Typical applications include industrial point-of-sale terminals, handheld barcode scanners, embedded serial debug ports on single-board computers, RS-232 ports on industrial controllers, and any 3.3V MCU-based board that needs a rugged 5-receiver COM port. The high ESD rating also makes it well-suited to factory-floor and medical equipment that must survive human-discharge events. When designing with this device, note that the QFN-32 EP package requires a thermal pad soldered to a ground copper pour for specified thermal performance. The four charge-pump capacitors must be low-ESR ceramic types placed within 5 mm of the IC. In shutdown mode, all transmitters and three of the receivers go to high impedance; the remaining two receivers stay active to monitor incoming handshaking signals. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical RS-232 design notes that are not consolidated in the manufacturer datasheet.

Запрос цены Контакты
ISL4241EIRZ-T - 3/5 RS-232 Transceiver, ±15kV ESD, 32-QFN | Renesas
ISL4241EIRZ-T

ISL4241EIRZ-T - 3/5 RS-232 Transceiver, ±15kV ESD, 32-QFN | Renesas

The Renesas ISL4241EIRZ-T is a 3-driver/5-receiver RS-232 transceiver that operates from a single 2.7V to 5.5V supply, housed in a 32-pin QFN (5x5 mm) package. It delivers ±15kV IEC61000-4-2 ESD protection on RS-232 pins, supports data rates up to 250 kbps, and consumes only 10 nA in shutdown, making it ideal for battery-powered portable equipment. What is an RS-232 transceiver? An RS-232 transceiver (also called a line driver/receiver) is an interface IC that translates logic-level UART signals (typically 0V/3.3V or 0V/5V CMOS/TTL) into the higher-voltage, inverted bipolar signals required by the EIA/TIA-232 and V.28/V.24 standards used for legacy serial ports. It belongs to the broader family of line drivers/receivers, which sits within interface ICs in the power management and signal-chain hierarchy. By integrating charge-pump voltage doublers/inverters and multiple drivers and receivers in a single chip, these devices replace legacy discrete designs built from op-amps, transistors, and DC-DC converters. Key features of the ISL4241EIRZ-T include a 3-transmitter/5-receiver channel count, on-board charge pump requiring only four external 0.1 µF capacitors, automatic shutdown with 10 nA quiescent current, and a hardware-enable pin. The transceiver is guaranteed to meet RS-232 specifications even at VCC = 3.0V, which is critical for systems powered directly from lithium-ion battery stacks. The 32-QFN (5x5) package with exposed thermal pad provides low thermal resistance for handheld designs, while the surface-mount footprint simplifies high-volume assembly. The device uses a regulated charge pump and on-chip voltage doubler/inverter to generate ±6V from a single 3.3V or 5V rail, so designers do not need a negative supply. Its drop-in compatible ISL4243E variant offers a slightly different enable logic (active-low SHDN) and complementary pinout options. ESD protection of ±15kV (HBM and Air Gap) on every RS-232 pin eliminates the need for external TVS diodes in most applications, simplifying BOM and reducing PCB area. Typical applications include notebook and laptop docking stations, palmtop PCs and PDAs, point-of-sale terminals, industrial serial-port modules, and any 3.3V-5V microcontroller system that needs legacy DB-9 communication. The 250 kbps data rate is also adequate for many GPS receivers, barcode scanners, and embedded debug ports. When designing with the ISL4241EIRZ-T, choose low-ESR ceramic capacitors (X7R, 0.1 µF) for the charge-pump flying and reservoir capacitors and keep capacitor ground returns short and direct to the IC GND pin to minimize EMI and ensure stable RS-232 output levels across temperature.

Запрос цены Контакты
ISL43240IRZ - Quad SPDT CMOS Analog Switch | Renesas
ISL43240IRZ

ISL43240IRZ - Quad SPDT CMOS Analog Switch | Renesas

The Renesas ISL43240IRZ is a CMOS, precision, quad SPDT (Single-Pole Double-Throw) analog switch that operates from a single +2V to +12V supply or from a ±2V to ±6V dual supply. Housed in a 20-pin QFN (4x4 mm) package, it integrates four independent SPDT switches with 25 Ω on-resistance and 5 Ω maximum rON flatness, delivering low-distortion signal routing for precision analog and mixed-signal systems. A quad SPDT analog switch is a key building block in the interface IC category (analog switch -> multiplexer -> signal routing IC -> interface IC -> integrated circuit). Each SPDT can route one input signal to one of two outputs, allowing efficient channel selection, signal multiplexing, and programmable gain networks. The ISL43240's CMOS construction provides ultra-low power consumption (5 µW typical), low leakage (5 nA maximum), and fast switching transitions (tON = 52 ns, tOFF = 40 ns), making it well suited for battery-powered and portable designs where power budget and signal integrity are both critical. Key features include a 25 Ω typical on-resistance across the analog signal range, 5 Ω rON flatness for low harmonic distortion, and break-before-make switching action to prevent momentary shorting between adjacent channels during transitions. Logic inputs are TTL/CMOS compatible with a guaranteed 1.65 V VIH and 0.5 V VIL across the full supply range, allowing direct interface with 1.8 V, 3.3 V, and 5 V microcontrollers without level shifters. The ISL43240's architecture is built on a sub-micron CMOS process, providing excellent ESD survival (≥2 kV HBM typical for the family) and rail-to-rail analog signal handling when powered from ±5 V. The device achieves low charge injection (typically <10 pC), which minimizes the glitch energy delivered to downstream sample-and-hold or ADC stages during switching events. Four switches in a single 4x4 mm QFN enable dense PCB layouts for multi-channel data-acquisition boards and instrumentation front-ends. Typical applications include battery-powered test and measurement instruments, USB-based audio switchboxes, programmable filter networks, data-acquisition front-ends, and industrial process control signal routing. The wide supply range and low quiescent power also make it attractive for handheld medical devices and portable industrial sensors where battery life is critical. When designing with this part, ensure logic levels are referenced to the same ground as the supply and that input signals remain within the analog input range (GND to V+ for single supply, V- to V+ for dual supply). Bypass V+ and V- (when used) with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pins to ensure clean rail transitions during high-speed switching. This page synthesizes distributor pricing, drop-in Renesas-family alternatives, and practical PCB layout guidance not found in the manufacturer datasheet alone, helping procurement and design engineers reduce risk in sourcing and integration.

Запрос цены Контакты
ISL54216IRTZ - USB 2.0 HS/UART Dual SP3T Switch | Renesas
ISL54216IRTZ

ISL54216IRTZ - USB 2.0 HS/UART Dual SP3T Switch | Renesas

The Renesas ISL54216IRTZ is a single-supply, dual SP3T (single-pole triple-throw) analog switch housed in a 12-lead 3x3 mm TQFN package, designed to multiplex USB 2.0 high-speed and UART signals through a common connector in portable battery-powered devices. The device operates from a single supply in the 2.7V to 4.6V range and supports multiplexing between three differential data sources per channel, with two independent channels (dual SP3T configuration) enabling simultaneous routing of USB D+/D- and UART TX/RX signal pairs through a single shared headphone or USB connector. A dual SP3T analog switch (also known as a dual 3-to-1 multiplexer) is an analog signal-routing IC that contains two independent SP3T switches, each capable of connecting a common terminal to one of three selectable throws. The SP3T topology belongs to the broader family of analog switches and multiplexers, sitting under interface ICs in the semiconductor hierarchy. The dual-SP3T configuration is purpose-built for the USB-plus-audio jack sharing architectures found in personal media players and other space-constrained portable electronics. Key features include low on-resistance designed for high-speed USB signaling, break-before-make switching to prevent momentary shorts between adjacent channels, and operation directly from a single Li-ion cell voltage. The switch targets USB 2.0 high-speed (480 Mbps) data rates, requiring tight on-resistance matching and low capacitance to preserve signal integrity at the high-speed eye-pattern mask. The 3x3 mm TQFN-12 footprint is among the smallest available for a dual-channel USB switch, supporting compact PCB layouts in mobile devices. The ISL54216IRTZ architecture uses paired N-channel MOSFET pass elements per throw, controlled by logic-level select inputs. The two channels are independent and may be controlled separately, enabling asymmetric routing such as routing USB on channel A while routing UART on channel B. The Renesas datasheet specifies typical on-resistance, off-isolation, and crosstalk parameters optimized for the 240 MHz fundamental frequency of USB 2.0 high-speed signaling. Typical applications include personal media players and portable media devices that share a single connector between headphone audio and USB data, mobile phones with combined USB/audio jacks, USB/UART multiplexing in development boards, and accessory-detection circuits that need to discriminate between headphone insertion and USB cable insertion on the same pins. The wide operating supply range also supports direct Li-ion battery connection, eliminating the need for an LDO upstream. When designing with this device, ensure the layout keeps USB data traces impedance-controlled (90 ohm differential) and short, and verify that break-before-make timing prevents cross-conduction when switching between USB and UART sources. The shared connector ground return must be designed to avoid ground bounce during mode transitions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
ISL59601IRZ - MegaQ Adaptive Video Equalizer, 1000ft | Renesas
ISL59601IRZ

ISL59601IRZ - MegaQ Adaptive Video Equalizer, 1000ft | Renesas

The Renesas ISL59601IRZ is a single-channel automatic composite video equalizer IC in the MegaQ product family, designed to compensate for long runs of Cat 5/6 or RG-59 cable up to 1000 feet (300 meters). Housed in a 20-pin QFN (4x4) package, this serial NTSC/PAL adaptive equalizer recovers high-quality video output with no user interaction or manual adjustment required. An adaptive video equalizer is a specialized signal-conditioning IC placed at the receiving end of long coaxial or twisted-pair cable runs. It automatically compensates for the frequency-dependent attenuation (cable loss) introduced by the cable, restoring the amplitude and group-delay characteristics of the original NTSC or PAL composite video signal. The MegaQ family belongs to the broader category of video amplifiers and equalizers, which are sub-categories of analog interface ICs used in CCTV, broadcast, and security infrastructure. Key features include automatic adaptive equalization across the full composite video bandwidth (typically up to 6 MHz for NTSC/PAL), single 5V supply operation, 75-ohm cable compatibility with 150-ohm back-terminated load, and integrated cable-type auto-detection. The device requires no external adjustments and operates transparently in the signal chain. Its 4x4 mm QFN-20 footprint integrates this functionality into compact PCB layouts used by security camera DVRs, video extenders, and broadcast receive equipment. The ISL59601 uses an adaptive equalization architecture that continuously monitors the received signal and adjusts its compensation curve in real time, eliminating the manual trim pots required by legacy fixed equalizer designs. Compared to passive cable compensation networks, the MegaQ approach maintains amplitude flatness and group delay across the full NTSC/PAL spectrum, preserving color burst integrity and reducing chroma/luma crosstalk even at maximum cable length. Typical applications include CCTV DVR video inputs, long-distance security camera installations over Cat 5/6 structured cabling, broadcast video distribution amplifiers, and video extender/receiver equipment for point-to-point analog video links up to 1000 feet. Engineers select the ISL59601 for shorter runs; the ISL59602/3/4/5 variants are drop-in compatible parts rated for longer cable lengths (2000, 3000, 4000, and 5300 feet respectively). When designing with this IC, ensure proper 75-ohm source/load impedance matching, place bypass capacitors close to the supply pins, and provide an exposed-die paddle connection to a clean ground plane for thermal dissipation. The ISL59601 differs from the ISL59602/3/4/5 only in maximum cable-length rating - all share the same QFN-20 footprint, enabling PCB reuse across product variants targeting different cable distances. This page synthesizes distributor pricing, MegaQ family cross-references, and practical layout guidance not consolidated in the Renesas datasheet, helping engineers select the right adaptive equalizer for their cable-run budget.

Запрос цены Контакты
ISL59603IRZ-T7 - Adaptive Composite Video Equalizer | Renesas
ISL59603IRZ-T7

ISL59603IRZ-T7 - Adaptive Composite Video Equalizer | Renesas

The Renesas Electronics ISL59603IRZ-T7 is a single-channel MegaQ adaptive composite-video equalizer designed to compensate automatically for long Cat 5/6 or RG-59 cable runs, in a 20-QFN (4 x 4 mm) package. According to the verified distributor listing, it supports serial NTSC and PAL video equalization and is fully adaptive to cable lengths up to 1 mile, or 1600 m. A video equalizer compensates for amplitude loss, phase distortion, and frequency-dependent degradation introduced by coaxial or twisted-pair transmission media. The MegaQ family belongs to the broader signal-conditioning hierarchy: composite-video processing, analog equalization, video signal conditioning, and interface ICs. Automatic adaptation is especially useful in security installations, camera links, surveillance backbones, and professional video equipment where long cables would otherwise require manual preset adjustment. The verified product data identifies the ISL59603 as part of the ISL59601, ISL59602, ISL59603, ISL59604, and ISL59605 MegaQ family. These devices target progressively longer transmission distances: the family description states that the ISL59601 reaches 1000 feet, while the ISL59605 reaches 5300 feet. The ISL59603 position is specifically identified as the 1-mile, 1600 m version. This makes model selection distance-based rather than a generic package substitution. The ISL59603IRZ-T7 is packaged in a 20-QFN, 4 x 4 mm surface-mount package. QFN construction supports compact PCB layouts while providing exposed thermal and electrical land patterns under the device. Exact pin functions, supply limits, gain settings, operating temperature, and RoHS or REACH status are not present in the supplied verified snippets, so those values are retained as [DATA_NEEDED] rather than inferred. Typical applications include long-distance composite-video surveillance camera transmission, CCTV monitor connections, security-control rooms, and CAT 5/6 or RG-59 cable links. The adaptive architecture removes the need for user interaction after installation, helping maintain usable video quality across variable cable lengths and losses. The key design consideration is to verify the complete cable, connector, source, and load chain before assuming that an equalizer alone will correct every image defect. Use the manufacturer datasheet for pin assignment, recommended application circuitry, decoupling, and video-level constraints before layout is released. This page combines verified distributor identification, manufacturer family positioning, practical application guidance, and component-replacement constraints that are not normally presented together on a basic distributor listing.

Запрос цены Контакты
ISL81483IB - 5V 250kbps RS-485/RS-422 Transceiver | Renesas
ISL81483IB

ISL81483IB - 5V 250kbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL81483IB is a 5V half-duplex RS-485 and RS-422 transceiver rated for data rates up to 250kbps and housed in an 8-pin SOIC package. Its 1/8-unit-load receiver network supports as many as 256 transceivers on one bus, making the device suitable for distributed industrial communication systems with numerous remote nodes. The low-power design provides an efficient balance between bus loading, communication speed, and system heat dissipation. An RS-485 transceiver is an interface IC that converts between logic-level signals and differential bus signals. RS-422 supports point-to-point, point-to-multipoint, and multidrop topologies, while RS-485 allows longer cables, broader node counts, and noise-resistant differential signaling. The ISL81483 belongs to the broader hierarchy of interface transceiver, communications interface, and semiconductor devices used to connect embedded controllers to field buses. Key characteristics include 1/8-unit-load bus loading, 5V operation, a maximum data rate of 250kbps, and support for both RS-485 and RS-422 networks. The reduced receiver loading permits more equipment on the same bus than a conventional one-unit-load receiver. The manufacturer documents low-power operation and options for high-speed or slew-rate-limited operation, allowing the interface strategy to be selected according to channel length, topology, and electromagnetic compatibility requirements. The ISL81483 and ISL81487 family combines a differential driver, differential receiver, and transmit/receive control in a compact 8-pin SOIC. Reduced unit load lowers the effective bus impedance presented by each node, which can help preserve signal amplitude and operating margin in long or highly populated networks. Designers must still account for termination, biasing, common-mode limits, and grounding according to the application circuit in the Renesas datasheet. Typical uses include process-automation networks, remote utility meter reading, industrial sensor gateways, building-control equipment, and remote instrumentation. In a utility-meter network, multiple apartment or building meters can route readings through an RS-485 segment toward a concentrator. The 256-node capability shown by the 1/8-unit-load architecture is particularly useful when field equipment must remain operational at low bus voltage. The primary design consideration is selecting the correct edge rate and bus topology. High-speed operation maximizes throughput but can increase reflected and radiated signal effects on long cables, while slew-rate limiting can reduce EMI at the cost of maximum data rate. Place the device near the bus connector, provide a solid ground reference, follow recommended termination practices, and validate signal integrity across cable lengths and environmental conditions. This product page combines the Renesas family description with practical bus-design guidance, package details, sourcing information, and a parameter-focused comparison of true pin-compatible alternatives. It helps engineers identify the correct transceiver role, assess node-count and data-rate constraints, and determine whether a direct replacement preserves the existing 8-pin SOIC PCB footprint.

Запрос цены Контакты
ISL81483IP - 1/8 Unit Load RS-485/RS-422 Transceiver | Renesas
ISL81483IP

ISL81483IP - 1/8 Unit Load RS-485/RS-422 Transceiver | Renesas

The Renesas ISL81483IP is a single, half-duplex RS-485/RS-422 transceiver designed for 5 V balanced communication systems. It presents a 1/8 unit load to the RS-485 bus, allowing as many as 256 transceivers on a network, and it is available in an 8-pin PDIP package for through-hole industrial and instrumentation designs. The device supports low-power operation and offers high-speed and slew-rate-limited operating options for balancing communication distance against signal integrity. Its RS-485 and RS-422 compliance allows the same physical-layer device to serve multidrop industrial buses, point-to-point RS-422 links, process automation equipment, and remote utility-meter-reading concentrators. An RS-485/RS-422 transceiver is an interface IC that converts logic-level transmit and receive signals into balanced differential bus signals. These differential signals reject common-mode noise and allow reliable data transfer over longer cables than single-ended interfaces. The transceiver also provides driver-enable and receiver-enable control so a node can transmit, receive, or remain inactive without driving the bus continuously. Key characteristics of the ISL81483IP include a 1/8 unit-load bus loading factor, a 5 V supply, half-duplex operation, and support for both RS-485 and RS-422 networks. The low unit load is especially useful for large-node systems such as process automation and remote meter-reading installations, where every connected node adds loading to the bus. The ISL81483IP uses a BiCMOS-oriented implementation described in the manufacturer datasheet as a fractional-unit-load transceiver family. Its driver and receiver functions are designed to meet the electrical requirements of balanced communication networks while keeping system power consumption low. The transceiver also provides separate receive and drive enables, allowing the host interface to control bus direction without external direction-control logic. Typical uses include industrial process-control terminals, remote meter-reading nodes, building automation controllers, factory monitoring equipment, and RS-422 point-to-point links. The 8-pin PDIP package is appropriate for legacy control boards, prototype systems, and designs assembled by through-hole manufacturing processes. When laying out an RS-485 board, place the transceiver close to the bus connector, route the differential pair as a matched pair, and provide a common-mode reference path for the connector shield. Keep the balanced traces away from switching nodes and high-current power paths. Use a termination resistor only where the bus topology requires it, and verify the cable length, node count, and baud rate against the transceiver's communication-distance guidance in the manufacturer datasheet.

Запрос цены Контакты
ISL81485IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas
ISL81485IB

ISL81485IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas

Renesas ISL81485IB is a single-channel, half-duplex RS-485/RS-422 line transceiver designed for 5 V operation with a maximum signaling rate of 30 Mbps. The device is manufactured in an 8-pin SOIC package and uses BiCMOS circuit technology. Its balanced differential interface supports bidirectional data transfer between systems connected with twisted-pair cabling, making it suitable for industrial communication, instrumentation, and data-acquisition equipment. A line transceiver converts logic-level signals into balanced differential signals for transmission over cable, while simultaneously receiving and converting differential cable signals into CMOS-compatible logic. The RS-485/RS-422 interface category combines differential signaling with high noise immunity and common-mode rejection. These characteristics make the ISL81485IB useful where communication distance, ground-potential differences, or electrically noisy surroundings can degrade single-ended digital interconnections. The ISL81485IB provides one transceiver, allowing a single interface to both transmit and receive. Its half-duplex configuration is appropriate for bus architectures in which a shared pair of conductors carries data in only one direction at a time. The manufacturer identifies the device as a 5 V, 30 Mbps RS-485/RS-422 transceiver and notes that its larger output voltage supports high-speed applications. It also specifies the circuit with a 10% tolerance capability, although the exact associated parameter requires confirmation in the manufacturer datasheet. BiCMOS implementation combines bipolar and CMOS characteristics within the integrated circuit. In a balanced transceiver, this can support relatively high data rates while maintaining low-power operation compared with older line-driver technologies. The 8-pin SOIC package also provides a conventional surface-mount footprint for industrial-control and communication equipment. Because a line transceiver interfaces between digital logic and external cabling, correct termination, biasing, grounding, and signal-integrity layout are as important as the nominal data rate. Typical uses for the ISL81485IB include industrial control networks, factory automation links, remote sensor and actuator connections, laboratory instrumentation, and embedded equipment communicating over balanced cabling. Its 30 Mbps capability is useful for shorter, controlled interconnects or legacy high-speed links where long-distance cabling would require careful attenuation and topology analysis. The device may also be used in RS-422 point-to-point systems when the system architecture supports the transceiver's shared bidirectional interface arrangement. A critical design consideration is that RS-485 and RS-422 interfaces are not automatically interchangeable at the network level. Cable length, topology, termination, idle state, and the number of connected drivers influence the correct implementation. Review the device's drive strength, receiver thresholds, enable behavior, and supply requirements in the manufacturer datasheet before assigning pins or selecting external components. This product page combines the confirmed operating characteristics, package information, sourcing guidance, and design considerations for the ISL81485IB. It also identifies the fields that require verification from the complete Renesas datasheet, helping engineers evaluate the transceiver without confusing electrical compatibility with guaranteed network interoperability.

Запрос цены Контакты
ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
ISL81485IU

ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL81485IU is a single-channel BiCMOS RS-485/RS-422 line transceiver designed for high-speed balanced data communication. It operates from a 5 V supply, supports data rates up to 30 Mbps, and is packaged in an 8-pin MSOP. The ISL81485IU provides the physical signaling interface between a digital controller and a differential bus using differential output and receiver functions. Its BiCMOS implementation combines bipolar and CMOS technologies to support the output voltage, speed, and noise characteristics required by RS-485 and RS-422 links. An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling. The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links. In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time. The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate. This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.

Запрос цены Контакты
ISL81486IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas
ISL81486IB

ISL81486IB - 5V 30Mbps RS-485/RS-422 Transceiver | Renesas

The Renesas Electronics ISL81486IB is a single 5V RS-485/RS-422 transceiver with half-duplex operation, data rates up to 30Mbps, and an 8-pin SOIC package. It provides one driver and one receiver for balanced industrial-communication links. An RS-485/RS-422 transceiver is an interface IC that converts differential line signals into logic-level signals and converts logic-level transmit data back into differential outputs. The ISL81486 belongs to the broader transceiver hierarchy: interface IC, RS-485/RS-422 transceiver, and balanced data-communication interface. Such devices connect controllers, sensors, industrial equipment, and field buses to long, noise-prone cable networks. The key operating characteristics include a 5V supply, half-duplex communication, a maximum specified signaling rate of 30Mbps, and support for both RS-485 and RS-422 applications. The BiCMOS implementation combines low-power CMOS behavior with bipolar output-driver capability. These characteristics make the device relevant to high-speed industrial links where data integrity and common-mode rejection are more important than low pin count. Renesas identifies the ISL81486 family as a BiCMOS, 5V-powered single transceiver intended for balanced communication. The family was developed with the larger output voltage and higher data-rate capability required by high-speed PROFIBUS-style applications. The ISL81486IB ordering code is supplied in an 8-pin SOIC package, matching the 8-SOIC designation used in distributor product listings. Typical uses include industrial controller interfaces, PROFIBUS-compatible equipment links, factory automation nodes, instrumentation gateways, and other balanced serial networks operating at elevated data rates. Because the transceiver is half-duplex, bus arbitration and transmit-enable control are central to the host-interface design. The external driver and receiver can also be used in opposite directions to implement a full-duplex RS-422 link when the application permits separate driver and receiver paths. Design the bus with controlled-impedance differential routing, appropriate termination, common-mode protection, and a return path for the reference ground. Place protection devices close to the connector and keep the balanced traces short and symmetric. Verify operation against the required cable length, data rate, topology, and grounding arrangement because maximum Mbps capability does not by itself guarantee reliable communication over every field-bus installation. This page combines manufacturer lifecycle information, package identification, functional characteristics, replacement considerations, and practical interface-design guidance. It also distinguishes verified drop-in candidates from package or function differences so engineers can assess legacy production continuity before releasing a redesign.

Запрос цены Контакты
ISL81486IU - 5V 40Mbps RS-485/RS-422 Transceiver | Renesas
ISL81486IU

ISL81486IU - 5V 40Mbps RS-485/RS-422 Transceiver | Renesas

Renesas Electronics ISL81486IU is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 40 Mbps and supplied in an 8-pin MSOP package. It combines a balanced bus driver and differential receiver in one 8-pin device, making it suitable for high-speed industrial communication links that require both RS-485 and RS-422 operation. A transceiver is an interface circuit that converts logic-level transmit and receive signals into balanced differential bus signals, then reconstructs the received signal. The ISL81486IU belongs to the RS-485/RS-422 interface IC hierarchy, where differential signaling improves noise immunity and allows reliable data transfer over longer cables than conventional single-ended interfaces. Key features include a 5 V supply, operation up to 40 Mbps, support for PROFIBUS, and BiCMOS circuit technology. These characteristics suit industrial automation, factory equipment, PROFIBUS nodes, process-control equipment, and other systems that combine long cable runs with demanding data rates. Its half-duplex architecture supports one driver and one receiver in a shared eight-pin package. The device is designed to conserve board space compared with separate driver and receiver packages. The MSOP outline also supports dense industrial-control assemblies, although exposed-pad thermal performance and PCB copper must be considered when the device dissipates substantial power. Differential bus routing, controlled impedance, and proper termination remain central to achieving reliable operation at the upper end of its 40 Mbps capability. Typical uses include high-speed RS-485 links in factory automation, RS-422 point-to-point links, PROFIBUS-compatible equipment, industrial controllers, data-acquisition systems, and communication interfaces operating from a 5 V rail. Because the bus topology determines correct operation, the network should use twisted-pair cabling, appropriate termination, and a common reference strategy between connected nodes. Designers should follow the manufacturer datasheet for the exact pin assignment, enable and receiver-enable behavior, driver output levels, receiver thresholds, and recommended external components. The part number suffix IU identifies the specified package/order configuration, but the package drawing and pin description should always be checked against the exact ordering code before PCB release. This page organizes the device’s interface role, package constraints, application fit, and verified ordering information into a design-oriented overview. It also distinguishes true same-package alternatives from parts that may only offer similar electrical functions, helping engineers assess PCB reuse without overlooking protocol, speed, or enable-control differences.

Запрос цены Контакты
ISL81487IB 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
ISL81487IB

ISL81487IB 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

Renesas Electronics ISL81487IB is a 5 V, single-channel RS-485/RS-422 half-duplex transceiver with a 5 Mbps maximum data rate, 1/8-unit-load driver capability, and 70 mV receiver hysteresis in an 8-pin SOIC package. Designed for balanced industrial communication links, it combines one driver and one receiver to support two-wire RS-485 buses or point-to-point RS-422 links. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential balanced signals for reliable communication over cables and noisy industrial environments. The RS-422 standard supports point-to-point, full-duplex signaling, while RS-485 allows multiple drivers and receivers on a shared half-duplex bus. The ISL81487IB belongs to the broader interface-IC hierarchy and is designed for low-power, 5 V system rails. Key characteristics include a 1/8-unit-load receiver input, a 70 mV receiver hysteresis, operation from a 5 V supply, and a maximum data rate of 5 Mbps. Its fractional unit load permits more nodes on an RS-485 bus than a conventional one-unit-load receiver. The 8-SOIC surface-mount package also supports compact, automated PCB assembly while exposing a standard leaded footprint rather than a fine-pitch land pattern. The BiCMOS transceiver architecture provides low-power operation for equipment that communicates over cables longer than the short reach of ordinary logic signals. Differential signaling improves common-mode noise rejection, while the low unit-load rating supports networks containing several transceivers. Because the ISL81487IB supports both RS-485 and RS-422, one device can serve industrial controllers, data-acquisition equipment, building automation, and point-to-point instrument interfaces. Typical uses include factory-floor sensor networks, industrial control gateways, serial port extenders, and remote I/O modules. In an RS-485 installation, the transceiver is placed between a UART or microcontroller and the balanced bus. Direction control determines whether the transmitter or receiver is enabled, while termination and biasing must be designed according to the cable topology. The primary layout consideration is keeping the balanced driver and receiver paths short, symmetrical, and physically separated from noisy switching circuits. Place termination components at the physical ends of the bus rather than beside every transceiver. Check the transceiver state during startup so that multiple drivers do not contend on the bus, and verify that the selected line baud rate remains within the device's 5 Mbps capability. This product data combines operating characteristics, lifecycle information, package details, drop-in family alternatives, comparison parameters, and practical interface-design guidance. It is intended to accelerate component evaluation and PCB planning while making the distinctions between the original ISL81487IB and related Renesas family members explicit.

Запрос цены Контакты
ISL81487IP - 5V RS-485/RS-422 Half-Duplex Transceiver | Renesas
ISL81487IP

ISL81487IP - 5V RS-485/RS-422 Half-Duplex Transceiver | Renesas

Renesas Electronics ISL81487IP is a 5 V, half-duplex RS-485/RS-422 interface transceiver with one driver and one receiver, a fractional 1/8 unit-load design, low power consumption, and an 8-PDIP package. The device supports both high-speed operation and slew-rate-limited communication, making it suitable for balanced industrial data links. An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic signals and differential, balanced bus signals. A differential receiver rejects common-mode noise, while the balanced driver improves signal integrity and interoperability over cables and long printed-circuit-board traces. In the signal-chain hierarchy, this component is a line transceiver, an interface IC, and part of a broader industrial communication and data-conversion system. The ISL81487IP combines a 5 V supply with a 1/8 unit-load receiver characteristic. Fractional unit loading permits more receiving nodes on the same bus than a full-unit-load receiver, which is valuable in multi-drop RS-485 networks. Its BiCMOS implementation combines low power use with high input impedance, while the balanced differential interface supports both RS-485 and RS-422 point-to-point or multidrop communication. The family supports two operating profiles: a high-speed profile for data-transfer links and a slew-rate-limited profile for reduced electromagnetic interference and improved control of bus-edge transitions. This flexibility allows the same physical interface concept to address factory automation, instrumentation, and industrial control networks. Package-level ESD protection is specified for the related ISL81487E family at ±15 kV HBM without latch-up. Typical uses include isolated and non-isolated industrial RS-485 buses, RS-422 links between controllers and peripherals, data acquisition systems, barcode or identification equipment, and embedded control modules. The 1/8 unit-load characteristic is particularly useful where the bus contains multiple receivers, while the through-hole 8-PDIP format supports prototype boards, legacy control equipment, and repair assemblies. When connecting the ISL81487IP to a multidrop bus, use a termination strategy appropriate for the cable length, topology, and baud rate. Keep the differential pair routed with continuous return-path reference, avoid unnecessary stubs, and place interface-protection components close to the connector. The driver enable and receiver enable functions must also be controlled correctly when the same transceiver supports half-duplex operation. This product record combines the manufacturer family information with practical interface guidance, verified drop-in candidates, and a parameter-by-parameter comparison. It is designed to help engineers confirm package compatibility, bus loading, ESD capability, and replacement suitability before incorporating the ISL81487IP into an RS-485 or RS-422 design.

Запрос цены Контакты
ISL83072EIUZA - 3.3V RS-485/RS-422 Transceiver, 8-MSOP | Renesas
ISL83072EIUZA

ISL83072EIUZA - 3.3V RS-485/RS-422 Transceiver, 8-MSOP | Renesas

The Renesas ISL83072EIUZA is a ±15kV ESD-protected, 3.3V-powered, single-channel RS-485/RS-422 transceiver housed in an 8-pin MSOP package. The device integrates one driver and one receiver in a half-duplex configuration, supports data rates up to 500 kbps in slew-rate-limited mode, and operates from a single 3.3V supply with true 1/8 unit load bus presentation, allowing up to 256 transceivers on a single bus. Per the Renesas product page, the ISL83072E family features ±15kV HBM ESD on the bus pins, full fail-safe receiver operation (open, short, terminated, floating), and hot-plug capability with three-state Tx/Rx outputs during power-up. A RS-485/RS-422 transceiver is a differential line driver/receiver IC used for robust, long-distance, noise-immune serial communication over twisted-pair cables. RS-485 supports multi-drop (32+ node) half- or full-duplex networks up to 1200 meters at lower speeds, while RS-422 is a point-to-point (or multi-drop up to 10 nodes) full-duplex standard. Both standards use differential signalling for high noise immunity, making them foundational building blocks of industrial fieldbus, building automation, and motor-control networks. Within the signal-chain taxonomy, the ISL83072E sits as a layer-1 physical interface between an MCU UART and the wired bus medium. Key specifications of the ISL83072EIUZA include ±15kV HBM ESD on RS-485 bus pins (driver output and receiver input), >7kV HBM ESD on all other pins, 3.0V to 3.6V supply operation, 1/8 unit load (allowing up to 256 transceivers on the bus), and low supply current. The driver features slew-rate-limited edges for reduced EMI, while the receiver offers full fail-safe to ensure a logic-high output under open-circuit, short-circuit, terminated, or floating bus conditions. The half-duplex topology shares a single differential pair between driver and receiver, reducing board area in multi-drop networks. The IC is fabricated on a BiCMOS process that combines bipolar drive strength with CMOS logic, delivering low quiescent current while maintaining the bus drive capability required by the RS-485 standard. Hot-plug tolerance prevents latch-up and bus contention when cards are inserted into a live backplane, and the three-state enable pins (DE, RE) allow individual node isolation for service or programming. The 8-MSOP package provides a compact footprint with adequate thermal performance for industrial environments. Typical applications include factory automation networks (Modbus RTU, Profibus DP), building automation (BACnet MS-TP, lighting controls), HVAC and access control, motor drive communication links, point-of-sale and weighing scales, and any multi-drop industrial fieldbus requiring robust 3.3V signalling. The half-duplex topology is well suited to bidirectional data exchange over a single twisted pair. When designing with this device, observe the bus-termination and stub-length recommendations in the datasheet to preserve signal integrity at the maximum data rate. Use a 100Ω differential termination at each cable end and keep stub lengths below one-tenth of the driver rise time for clean edges. Enable hot-plug considerations by sequencing the supply and DE/RE pins to avoid contention during board insertion.

Запрос цены Контакты
ISL83078EIUZA - 3.3V RS-485/422 Transceiver | Renesas | MSOP-8
ISL83078EIUZA

ISL83078EIUZA - 3.3V RS-485/422 Transceiver | Renesas | MSOP-8

The Renesas ISL83078EIUZA is a 3.3V-powered, ±15kV ESD-protected, full fail-safe RS-485/RS-422 transceiver in an 8-pin MSOP package. It provides one driver and one receiver (1/1 transceiver, half-duplex) and supports both high-speed (up to 20Mbps) and slew-rate-limited operation modes for EMI-sensitive designs. The device operates from a single 3.3V supply, drawing a low quiescent current while delivering robust differential signaling across long cable runs. A transceiver in the RS-485/RS-422 family is a mixed-signal interface IC that converts a single-ended TTL/CMOS logic signal into a differential voltage on the bus and vice versa. The RS-485 standard defines a balanced, multipoint differential bus capable of driving up to 32 unit loads over twisted pair, supporting common-mode ranges of -7V to +12V and cable lengths up to 1200m at reduced data rates. Renesas (formerly Intersil) ICs in this category are typically integrated into industrial fieldbus, building automation, motor control, and process-control networks, where the differential signaling rejects common-mode noise from motors, relays, and high-voltage switching. Key features of the ISL83078EIUZA include ±15kV HBM ESD protection on the bus pins (per IEC 61000-4-2 air discharge), a full fail-safe receiver topology that guarantees a logic-high output when the inputs are open, shorted, or terminated but idle, and a wide 3.0V to 3.6V supply range with logic-compatible I/O. The device is hot-plug tolerant, meaning it will not latch up or source excessive current when inserted into a live backplane, and it operates across the -40°C to +85°C industrial temperature range. Architecturally, the ISL83078EIUZA uses BiCMOS process technology to combine low-power CMOS logic with bipolar bus drivers, achieving rail-to-rail common-mode tolerance and tight duty-cycle symmetry. The driver slew rate can be selected via the SLOPE pin: high slew rate for maximum throughput, or limited slew rate to reduce EMI emissions and allow unshielded cable use. Both 1/8-unit-load (ISL83072-family) and 1-unit-load (ISL83078-family) variants exist; the 1-unit-load version supports up to 32 transceivers on a single bus. Typical applications include industrial programmable logic controllers (PLCs), factory-automation sensors and actuators, HVAC and building-automation nodes, motor-drive feedback links, and any 3.3V-only system that needs robust point-to-point or multipoint RS-485 communication. The 8-pin MSOP footprint saves board area versus industry-standard SOIC-8 parts while remaining pin-compatible with most competitor solutions. When designing with the ISL83078EIUZA, choose the SLOPE pin state early in the design: tie high for 20Mbps throughput, tie low for EMI-limited operation. Place termination resistors (120 Ω) only at the two ends of the bus, never at intermediate nodes, and use a twisted pair with a ground reference to maximize noise rejection. This page synthesizes distributor pricing, cross-reference drop-in alternatives, and PCB-layout guidance not found on the manufacturer datasheet alone.

Запрос цены Контакты
ISL8323IB - Dual 60 Ohm SPST Analog Switch | Renesas
ISL8323IB

ISL8323IB - Dual 60 Ohm SPST Analog Switch | Renesas

Renesas Electronics ISL8323IB is a dual single-pole single-throw analog switch with a 60 ohm on-resistance, packaged in an 8-SOIC. The device is designed for low-voltage, single-supply operation, and the verified distributor data identifies it as a 2-circuit 1:1 interface switch. Its two independent SPST channels allow a signal to be routed, isolated, sampled, or connected to a test path without changing the system PCB. An analog switch is an integrated semiconductor that controls an analog signal path with digital control logic. The switch belongs to the analog switch and multiplexer hierarchy, which sits within interface ICs and system-level signal-routing networks. Unlike a mechanical relay, an analog switch operates quickly and occupies little board area, making it suitable for portable, industrial, communications, and test equipment where supply voltage, signal integrity, leakage, and on-resistance determine performance. The ISL8323IB family is described as precision dual analog switches for single-supply systems, including battery-powered equipment. Verified data identifies a maximum off leakage of 100 pA, off-state channel capacitance of 9 pF, and charge injection of 5 pC maximum per channel. Crosstalk is specified as -85 dB at 1 MHz, indicating strong isolation between the switched paths. The operating temperature range is -40°C to +85°C, and the 8-SOIC package uses surface-mount assembly. The 60 ohm on-resistance balances conduction loss against low-voltage signal operation, while 9 pF off capacitance and 100 pA leakage help preserve high-impedance sources when a channel is open. Because the part is intended for a single supply, system designers should verify input and control-signal levels against the manufacturer datasheet before assigning logic thresholds or bipolar signals. Typical uses include battery-powered measurement systems, analog signal routing in test equipment, communication interfaces, and compact embedded control platforms. The low 9 pF off capacitance is particularly useful when the switch connects to high-impedance sensors or amplifiers, while the -85 dB crosstalk specification supports isolated routing of moderate-bandwidth signals. The main design consideration is to verify supply and logic levels, control-pin polarity, and signal amplitude in the datasheet. Place the device close to the signal source when switching high-impedance nodes to minimize parasitic capacitance, and use a ground reference and controlled layout to prevent injected noise from appearing across the open switch. This page combines verified distributor specifications, package and lifecycle details, comparison information, and practical design guidance. It is intended to help engineers identify whether the ISL8323IB is suitable for a new analog-routing design and to locate its datasheet before committing to a PCB layout.

Запрос цены Контакты
ISL8323IB-T - Dual 60Ω SPST Analog Switch | Renesas
ISL8323IB-T

ISL8323IB-T - Dual 60Ω SPST Analog Switch | Renesas

Renesas Electronics ISL8323IB-T is a low-voltage, single-supply dual analog switch containing two independently controlled, normally open SPST switches. Each switch presents a specified on-resistance of 60 ohm, and the device is packaged in an 8-SOIC for surface-mount assembly. The switch family is designed for precision signal routing in low-voltage systems operating from a single supply up to 12 V. An analog switch is an integrated interface IC that routes signals between terminals with controlled impedance. A single-pole, single-throw, or SPST, switch has one conducting path when enabled and an open circuit when disabled. The ISL8323 uses two such paths in one package, making it useful when a design needs to isolate, disconnect, or select two analog signals without using mechanical relays. The primary electrical characteristics include two switch circuits, 60 ohm on-resistance, and normally open contacts. The manufacturer datasheet information identifies maximum charge injection of 5 pC, off-state channel capacitance of 9 pF, maximum off-state leakage current of 100 pA, and crosstalk of -85 dB at 1 MHz. These parameters determine how much switching transients and signal coupling can affect sensitive downstream circuits. The ISL8323 family supports single-supply operation, with the documented supply range extending to 12 V. Its low-voltage architecture is appropriate for battery-powered instruments, portable measurement equipment, automated test systems, and low-voltage control systems. Two separate switches can route independent control or sensor signals while sharing a common supply and ground reference. Use the ISL8323IB-T when normally open behavior is required. The related ISL8324 provides normally closed switches, while the ISL8325 combines one normally open and one normally closed switch for SPDT-style routing. Because contact state changes the logic behavior, these family members are not automatic drop-in substitutes for an existing normally open design. Layout should minimize trace length around the switched nodes, maintain a continuous ground reference, and keep sensitive signal paths away from noisy supply and control routes. Confirm the control levels, input voltage range, break-before-make behavior, and application leakage budget against the manufacturer datasheet before production release. This product page combines the switch configuration, electrical limits, package information, family distinctions, and application guidance needed to evaluate the ISL8323IB-T and identify a valid replacement without relying on packaging suffix changes alone.

Запрос цены Контакты
ISL8323IBZ - 60 ohm Dual SPST Analog Switch | Renesas
ISL8323IBZ

ISL8323IBZ - 60 ohm Dual SPST Analog Switch | Renesas

The Renesas Electronics ISL8323IBZ is a dual single-pole single-throw analog switch with two normally open switches, a typical on-resistance of 60 ohms, and an 8-pin SOIC package. It operates from a single supply of +2.7 V to +12 V and is optimized for low-power signal routing in battery-powered and portable equipment. The device also provides a maximum off leakage current of 100 pA and low power consumption of 5 uW. An analog switch is a semiconductor-based interface device that routes low-frequency analog signals between circuit nodes under digital control. The ISL8323 belongs to the analog-switch and multiplexer hierarchy within interface ICs, with the ISL8323IBZ providing two independent SPST paths rather than a shared multiplexer structure. Its normally open configuration leaves each switch disconnected until the corresponding control input activates it. Key characteristics include 60 ohm on resistance, 100 pA maximum leakage, 5 uW power consumption, 5 pC maximum charge injection, and 9 pF maximum channel capacitance. The operating temperature range extends from -40 C to +85 C. These specifications make the device appropriate where low leakage, low power, and compact signal isolation matter more than ultra-low resistance or very high switching speed. The ISL8323 family is designed for single-supply operation between 2.7 V and 12 V. Each independent switch can be controlled separately, allowing two signals to be routed, isolated, sampled, or connected to a shared analog resource. The 5 pC maximum charge injection limits control-transition disturbance at sensitive input nodes, while 9 pF capacitance helps preserve bandwidth in moderate-impedance circuits. Typical uses include battery-powered measurement systems, portable medical and industrial equipment, analog test circuits, signal isolation between amplifiers and data converters, and low-leakage sensor interfaces. The low 5 uW power figure is particularly useful in equipment where standby consumption must remain small. Because the on resistance is 60 ohms, the switch is most suitable for sensor, control, and instrumentation signals rather than high-current or low-impedance RF paths. Designers should verify signal amplitude, leakage-driven error, control-logic levels, and bandwidth before committing the device to a precision circuit. The SOIC footprint simplifies assembly, but unused control inputs and switch terminals must be connected according to the manufacturer pin-description table. Input voltages must remain within the specified supply range, and analog signals should not exceed the device's allowed voltage limits. This page organizes the verified electrical characteristics, lifecycle status, sourcing information, pin-access guidance, and application-specific design considerations for engineers evaluating the ISL8323IBZ. It also distinguishes true pin-compatible alternatives from nearby family members that use different switch configurations, helping prevent footprint-compatible but electrically unsuitable substitutions.

Запрос цены Контакты
ISL8324IB - Dual 60 Ohm SPST Analog Switch | Renesas
ISL8324IB

ISL8324IB - Dual 60 Ohm SPST Analog Switch | Renesas

The Renesas ISL8324IB is a dual, single-pole single-throw analog switch with two independently controlled 1:1 circuits, 60 ohm on-resistance, and an 8-SOIC package. According to the distributor data, it operates from a single low-voltage supply and is specified for -40 C to +85 C. These verified facts place it in the low-voltage switching hierarchy: SPST analog switch -> analog switch/multiplexer -> interface IC -> semiconductor. An analog switch connects or discloses a signal path with controlled resistance rather than amplifying or converting it. The ISL8324IB is useful when a sensor, test point, audio path, or measurement input must be routed or isolated while preserving signal integrity. Its two SPST channels provide independent routing control, while the 1:1 topology avoids changing the nominal signal direction when a channel is closed. The verified distributor listing identifies the device as a 2-circuit IC switch with 1:1 configuration, 60 ohm on-resistance, and 8-SOIC packaging. These are the principal selection criteria for PCB compatibility and signal-path loss assessment. The manufacturer datasheet must be consulted for complete input-voltage limits, control-logic levels, leakage, charge injection, bandwidth, and absolute maximum ratings before a design is released. The single-supply architecture simplifies systems that already operate from a low-voltage rail, while the -40 C to +85 C range covers industrial and commercial temperature environments. Engineers should treat control inputs, analog signal amplitudes, supply sequencing, and power dissipation as design constraints rather than assume that a low-voltage-rated switch can accept arbitrary signals. The 8-SOIC footprint is compatible only when the alternative has the same pin arrangement and electrical function. Typical uses include battery-powered sensor interfaces, analog test and measurement equipment, audio routing, data-acquisition front ends, and low-voltage communication interfaces. In a sensor interface, each SPST path can isolate a transducer during measurement or connect it to an amplifier. In test equipment, the switch can provide controlled connectivity between an external fixture and an analog input. In audio routing, the 60 ohm resistance is a relevant insertion-loss and drive-current consideration. A key design practice is to check the complete signal path, including source impedance, switch resistance, leakage, control timing, and downstream input capacitance. The datasheet's logic thresholds and dynamic characteristics should be compared with the controlling device. If replacement is considered, verify package pinout, supply range, on-resistance, control polarity, bandwidth, leakage, and temperature rating rather than relying only on the SOIC outline. This product data combines verified distributor identity, package, switching configuration, resistance, temperature range, cross-reference results, and practical engineering guidance. It is intended to support initial component selection and comparison, while incomplete electrical limits remain explicitly marked for verification rather than guessed.

Запрос цены Контакты
ISL8324IB-T - Dual SPST Analog Switch, 60 Ohm, 8-SOIC
ISL8324IB-T

ISL8324IB-T - Dual SPST Analog Switch, 60 Ohm, 8-SOIC

Renesas Electronics ISL8324IB-T is a low-voltage, single-supply, dual SPST analog switch with a 1:1 signal configuration, 60 ohm on-resistance, and an 8-pin SOIC package. The device is designed for routing low-voltage analog or digital signals when a compact, surface-mount switch with two independent channels is required. An analog switch is an integrated semiconductor device that connects or disconnects signal paths under control of logic signals. The SPST, or single-pole single-throw, architecture provides one controlled conduction path per channel. The ISL8324IB-T therefore supports two separately controlled switching functions in one package, reducing board area compared with discrete switching solutions. The ISL8324IB-T belongs to the Intersil ISL8323-ISL8325 family of precision, dual analog switches. Its operating characteristics identify a 60 ohm on-resistance and a 1:1 configuration. The 8-SOIC package is a standard surface-mount package for compact industrial and embedded designs. The device is identified as an industrial-temperature component and is intended for single-supply operation, making it relevant to battery-powered equipment, measurement systems, and control circuits. The two switch channels can route analog control signals, sensor outputs, test points, or low-voltage communication paths. Their independently controlled state allows a controller to isolate a signal source, select between signal paths, or create a controlled connection between an external circuit and a system test point. The compact SOIC footprint also makes the device suitable for designs that cannot accommodate a larger analog-switch package. When using the ISL8324IB-T, verify the supply voltage, control-logic levels, signal-voltage range, switch leakage, and operating temperature against the application requirements. The control pins and switched terminals must remain within the limits defined by the manufacturer datasheet. Because the device has two independent channels, PCB layout should keep the control traces away from sensitive analog paths and provide adequate grounding around the switching network. This product page combines the manufacturer family description, package and circuit details, comparison information, and practical design guidance. It also explains where a true same-package replacement can be used and where a different package requires a PCB change.

Запрос цены Контакты
ISL8324IBZ - Dual SPST Analog Switch, 60 Ohm, 8-SOIC | Renesas
ISL8324IBZ

ISL8324IBZ - Dual SPST Analog Switch, 60 Ohm, 8-SOIC | Renesas

The Renesas Electronics ISL8324IBZ is a dual SPST analog switch with a 1:1 voltage-transfer configuration, 60 ohm on-resistance, and normally closed switch behavior. The device is packaged in an 8-pin SOIC and operates from a single supply in the ISL8323 through ISL8325 family range of 1 V to 12 V. Its two independent channels make it suitable for routing low-voltage analog and digital signals in compact embedded systems. An analog switch is an interface IC that connects or disconnects signal paths under digital control. SPST means single-pole, single-throw: one input and one output form a controlled connection for each channel. The normally closed designation means the relevant path is connected before the control input changes state. Together, analog switch, SPST switch, multiplexer interface, and low-voltage switching IC describe the ISL8324IBZ's role within general-purpose interface and power-management electronics. The headline characteristics are its two switch circuits, 60 ohm on-resistance, 1:1 signal routing, single-supply operation, and 8-SOIC package. The 60 ohm resistance is important when the switch drives a lightly loaded or high-impedance node because it limits the voltage-divider effect between the source and destination. The 1:1 configuration preserves signal polarity rather than inverting the selected signal, which simplifies routing in measurement, control, and embedded peripheral systems. ISL8324IBZ belongs to the Renesas ISL8323-ISL8325 precision dual analog-switch family. Individual family members can differ in switch polarity, on-resistance, and control behavior, so an engineer should verify the complete pin description and electrical table before substituting one MPN for another. The IBZ ordering code specifically identifies the 8-pin SOIC configuration used in this part. Typical uses include battery-powered measurement equipment, analog sensor routing, test and measurement systems, and embedded signal-path multiplexing. In each case, the switch can isolate or reconnect a signal node under firmware control. Battery-powered applications benefit from the single-supply operation, while the compact SOIC footprint supports conventional surface-mount assembly and routing in mixed-signal designs. The principal design consideration is control-state compatibility. Because the ISL8324IBZ is normally closed, firmware and external pull resistors must be evaluated against the default signal path and the desired powered state. Designers should also account for the 60 ohm series resistance when calculating settling behavior, attenuation, and drive requirements for the connected load. This page organizes the verified switch configuration, package details, application guidance, and engineering trade-offs in one searchable reference. It emphasizes how the dual-channel architecture, normally closed behavior, 1:1 routing, and 60 ohm resistance affect practical circuit decisions when replacing or selecting an analog switching component.

Запрос цены Контакты
ISL8325IB - Dual SPST 60Ohm Analog Switch | Renesas
ISL8325IB

ISL8325IB - Dual SPST 60Ohm Analog Switch | Renesas

The Renesas Electronics ISL8325IB is a low-voltage, single-supply, dual SPST analog switch with two independently controlled 1:1 circuits, an on-resistance of 60 ohms, and an 8-pin SOIC package. The verified distributor data identifies the device as a surface-mount SOIC part, while the manufacturer datasheet result describes it as a low-voltage, single-supply dual SPST analog switch. Its primary role is connecting or disconnecting low-voltage analog signals rather than regulating power or driving high current. An analog switch is a semiconductor interface device that routes signals between circuit nodes under digital control. The SPST designation means each channel has a single-pole, single-throw arrangement, and 1:1 describes the signal-path configuration. As a dual analog switch, the ISL8325IB provides two switching sections that can be used for signal isolation, sample-and-hold paths, test-point routing, or other analog signal-routing systems. It belongs to the broader semiconductor hierarchy of analog switches, interface ICs, and signal-chain components. The verified data specifically confirms two circuits, SPST configuration, 60-ohm on resistance, and an 8-pin SOIC package. The data also identifies an industrial temperature grade from distributor listings. Other electrical characteristics, including supply-voltage limits, control thresholds, leakage current, channel capacitance, switching time, and absolute maximum ratings, are not included in the supplied sources and are marked for data confirmation rather than estimated. This conservative approach prevents unverified parameters from being presented as guaranteed design values. Typical use cases include low-voltage analog signal routing, measurement systems, communication interfaces, and test or control circuits where a digital control signal must select between analog paths. The SOIC-8 footprint is useful for conventional surface-mount PCB assembly. Because an analog switch can influence signal integrity, the input and output routing should be short and appropriately terminated, and control signals should be driven with compatible voltage levels. The 60-ohm resistance should be considered in the context of source impedance, load capacitance, bandwidth, and acceptable insertion loss. The ISL8325IB is appropriate when the design requires two SPST analog routes and can operate within the verified device limits. Its compact SOIC package and two-channel arrangement can simplify layouts compared with discrete switch implementations. The primary trade-off is that the verified data does not provide enough detail to guarantee off-state isolation, dynamic performance, or power-consumption targets without consulting the complete manufacturer datasheet. This page combines verified distributor identity, package information, datasheet availability, pricing-source links, and practical selection guidance. It also distinguishes confirmed facts from parameters that require engineering verification. Buyers should compare the complete datasheet, validate logic levels and signal amplitudes, and confirm lifecycle and qualification requirements before releasing a production design.

Запрос цены Контакты