EPM9560RI208-20N - MAX 9000 CPLD 12K Gates 208-RQFP | Intel
Артикул: EPM9560RI208-20N ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
EPM9560RI208-20N Обзор
A CPLD (Complex Programmable Logic Device) is a programmable logic IC that combines multiple programmable logic array blocks and macrocells with a programmable interconnect matrix, allowing designers to implement custom digital logic without fabricating an ASIC. Within the semiconductor taxonomy, the MAX 9000 CPLD sits under programmable logic devices (PLDs), alongside FPGAs and simple PLDs (SPLDs), and is used for glue logic, bus interfacing, and state-machine control.
The MAX 9000 architecture is built on Altera's third-generation Multiple Array MatriX (MAX) architecture, fabricated on an advanced CMOS process with EEPROM configuration cells. This non-volatile EEPROM technology allows the device to retain its configuration without an external configuration memory, unlike SRAM-based FPGAs. The -20 speed grade provides a 20 ns pin-to-pin delay, while faster -15 and -10 grades reach 15 ns and 10 ns respectively, with counter speeds up to 144 MHz on the fastest grade.
Key features include 5.0 V in-system programmability via the built-in JTAG interface, 560 macrocells, and support for the MAX+PLUS II development system, which offers schematic, VHDL, Verilog HDL, and AHDL design entry, compilation, logic synthesis, simulation, timing analysis, and device programming in a single integrated toolchain.
Typical applications include industrial control glue logic, bus bridging and address decoding, telecommunications line-card control, test and measurement instrumentation, and legacy system maintenance where 5 V logic levels and non-volatile configuration are required.
When designing with the EPM9560RI208-20N, note that the 5.0 V core and I/O supply requires careful power distribution and decoupling, and that the RQFP package demands adequate thermal relief and copper area for reliable solder joints. Because the device is EEPROM-based, it can be reprogrammed in-system, simplifying field upgrades.
This page synthesizes distributor availability, drop-in speed-grade alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for sourcing and designing with the EPM9560RI208-20N.
Аналоги без доработки для EPM9560RI208-20N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с EPM9560RI208-20N (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Architecture, In-System Programmability, Configuration Memory.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EPM9560RI208-15N
✅ Прямая замена✓ В наличии
$19.45 / шт.
Открыть даташит →EPM9560RI208-10N
✅ Прямая замена✓ В наличии
$61.75 / шт.
Открыть даташит →EPM9560RI208-15
✅ Прямая замена✓ В наличии
$20.1 / шт.
Открыть даташит →EPM9560RI208-10
✅ Прямая замена✓ В наличии
$67.8 / шт.
Открыть даташит →EPM9560RI208-20
✅ Прямая замена✓ В наличии
$21.1 / шт.
Открыть даташит →EPM9560RI208-20N Максимальные параметры и электрические характеристики
| Device Family | MAX 9000 |
| Usable Gates | 12,000 |
| Macrocells | 560 |
| Pin-to-Pin Delay | 20 ns (-20 speed grade) |
| Counter Speed | 100 MHz |
| Напряжение питания | 5.0 V |
| Configuration Technology | EEPROM (non-volatile) |
| In-System Programmability | Yes, via IEEE Std. 1149.1 JTAG |
| Корпус | 208-pin RQFP |
| Тип монтажа | Surface Mount |
| Рабочая температура | Industrial (-40C to +85C) |
| Development Tool | MAX+PLUS II |
| Design Entry | Schematic, VHDL, Verilog HDL, AHDL |
| Packaging | Tray |
| Logic Architecture | Third-generation MAX (Multiple Array MatriX) |
| Fabrication Process | Advanced CMOS |
Руководство по цоколевке EPM9560RI208-20N в корпусе 208-pin rqfp
Цоколевка для EPM9560RI208-20N (корпус 208-pin rqfp). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для EPM9560RI208-20N.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
EPM9560RI208-20N подходит для 6 применениеs: Industrial Control Glue Logic, Bus Bridging and Address Decoding, Telecommunications Line-Card Control, Test and Measurement Instrumentation, Legacy System Maintenance and Redesign, Automotive and Transportation Electronics.
Industrial Control Glue Logic
The EPM9560RI208-20N fits industrial control glue logic because its 12,000 usable gates and 560 macrocells can absorb address decoding, chip-select generation, and handshake logic that would otherwise require dozens of discrete 74-series ICs. Its industrial temperature grade of -40C to +85C and 5.0 V EEPROM-based configuration tolerate the electrical noise and temperature swings of factory-floor equipment. The device is typically placed between a microcontroller and peripheral ICs, implementing wait-state generation and bus arbitration at a 20 ns pin-to-pin delay. Unlike SRAM-based FPGAs, it needs no external configuration memory, so it boots instantly and cannot be corrupted by brownouts. The trade-off is higher static power than modern low-voltage CPLDs, but the 5 V interface simplifies level matching to legacy industrial buses.
Рекомендуется
Bus Bridging and Address Decoding
The EPM9560RI208-20N is well suited to bus bridging and address decoding because its 560 macrocells can implement wide address comparators, wait-state generators, and protocol translators between 8-bit, 16-bit, and 32-bit buses. With a 20 ns pin-to-pin delay and 100 MHz counter speed, it handles legacy 5 V bus timing without external latches. Designers commonly place it between a host processor and peripherals such as UARTs, timers, and memory devices, using the JTAG interface for in-system reprogramming during development. The EEPROM configuration retains the bridge logic across power cycles, which is critical for systems that must boot deterministically. The main trade-off is that the 5.0 V supply and RQFP package require careful power distribution and board area compared with modern 1.8 V CPLDs.
Рекомендуется
Telecommunications Line-Card Control
The EPM9560RI208-20N suits telecommunications line-card control because its 12,000 usable gates can implement channel supervision, alarm monitoring, and time-slot interchange glue logic on a single non-volatile device. The 5.0 V EEPROM-based MAX 9000 architecture is immune to configuration loss during the hot-swap and power-sequencing events common in telecom shelves, unlike SRAM FPGAs that need a configuration PROM. Its 20 ns pin-to-pin delay supports the control-path timing of E1/T1 and SONET overhead interfaces, while the 208-pin RQFP provides enough I/O for dense backplane connectors. The device is typically placed on the line card between the framer and the backplane interface, handling interrupt aggregation and register access. The trade-off is higher power than low-voltage CPLDs, requiring adequate thermal relief.
Рекомендуется
Test and Measurement Instrumentation
The EPM9560RI208-20N fits test and measurement instrumentation because its 560 macrocells can implement trigger logic, pattern generation, and acquisition sequencing with deterministic 20 ns timing. The non-volatile EEPROM configuration means the instrument boots to a known state without a configuration load, which is important for automated test equipment that must start quickly and repeatably. Designers use the JTAG interface to update trigger algorithms in the field, and the 5.0 V I/O interfaces directly with legacy instrument backplanes and analog front-end control lines. The 100 MHz counter speed supports moderate-rate event counting and timestamping. The main trade-off is that the RQFP package and 5 V supply consume more board area and power than modern alternatives, so thermal and layout planning are required.
Рекомендуется
Legacy System Maintenance and Redesign
The EPM9560RI208-20N is a key part for legacy system maintenance and redesign because it preserves the exact 208-pin RQFP footprint, 5.0 V interface, and MAX+PLUS II design flow of existing MAX 9000 designs. When an original board must be repaired or reproduced, using the same device avoids re-qualification and re-layout costs. The EEPROM configuration can be reprogrammed in-system via JTAG, so field upgrades do not require removing the part. Engineers can also migrate to faster pin-compatible grades such as the EPM9560RI208-15N or EPM9560RI208-10N if timing margins are tight. The trade-off is that the MAX 9000 family is obsolete, so long-term supply depends on residual inventory and should be managed with last-time-buy planning.
Рекомендуется
Automotive and Transportation Electronics
The EPM9560RI208-20N can serve automotive and transportation electronics where 5 V logic and non-volatile configuration are required, such as body-control modules, dashboard controllers, and legacy powertrain interfaces. Its industrial temperature grade of -40C to +85C covers many under-hood and cabin environments, and the EEPROM configuration survives the cold-crank and load-dump events that can reset SRAM-based logic. The 12,000 usable gates and 560 macrocells implement multiplexed switch inputs, lamp drivers, and CAN gateway glue logic at a 20 ns pin-to-pin delay. The device is typically placed between a vehicle network controller and discrete I/O. The trade-off is that the part is not AEC-Q100 qualified, so automotive use requires additional qualification evidence from the system integrator.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для EPM9560RI208-20N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EPM9560RI208-15N | EPM9560RI208-10N | EPM9560RI208-20 |
|---|---|---|---|---|
| Package | 208-pin RQFP | 208-pin RQFP - same | 208-pin RQFP - same | 208-pin RQFP - same |
| Brand | Intel | Intel | Intel | Intel |
| Pin-to-Pin Delay | 20 ns | 15 ns | 10 ns | 20 ns |
| Usable Gates | 12,000 | 12,000 | 12,000 | 12,000 |
| Macrocells | 560 | 560 | 560 | 560 |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Temperature Grade | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial (-40C to +85C) |
| Configuration Technology | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) |
| JTAG ISP | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) | Yes (IEEE Std. 1149.1) |
Ключевые отличия
- Non-volatile EEPROM configuration (против SRAM-based FPGAs)
- Pin-compatible speed-grade upgrade path (против EPM9560RI208-15N)
- 5.0 V interface compatibility (против EPM9560RI208-10N)
- Industrial temperature grade (против EPM9560RC208-20)
Заметки по проектированию
The EPM9560RI208-20N requires a well-regulated 5.0 V supply with adequate decoupling. Place at least one 0.1 uF ceramic capacitor per power pin pair as close to the device as possible, plus bulk 10 uF to 47 uF capacitors near the package corners. Estimated: at a typical 5 V CPLD operating current of a few hundred milliamps, a 100 mV supply droop corresponds to roughly 0.5 W of additional dissipation in the regulator, so verify the regulator's thermal margin. Follow the MAX 9000 datasheet power-supply recommendations for decoupling network values.
The 208-pin RQFP package requires careful PCB layout to avoid solder-joint defects. Use a solder-mask-defined pad geometry per the datasheet land pattern, provide thermal relief on ground pins, and keep the exposed copper balanced to prevent package warping during reflow. Route JTAG signals (TCK, TMS, TDI, TDO) as short, controlled-impedance traces and keep them away from high-speed switching nodes. Provide test points for all JTAG pins to support in-system programming and boundary-scan test.
A common pitfall with the EPM9560RI208-20N is assuming SRAM-FPGA-like configuration behavior. Because the MAX 9000 uses EEPROM cells, the device retains its design without a configuration PROM, but it must still be programmed before first use. Ensure the JTAG chain is correctly terminated and that the programming file targets the -20 speed grade; using a -15 or -10 timing model can cause over-constraining or under-constraining of the fitter. Also verify that the obsolete lifecycle status is reflected in your last-time-buy and obsolescence plan.
Информация о соответствии
Compliance data for the EPM9560RI208-20N was not present in the verified web data. The device is obsolete and predates current RoHS/REACH documentation practices; confirm compliance with the distributor or manufacturer before use in regulated markets.