EPM240GF100C5N - MAX II CPLD, 192 MC, 4.7ns, 100-FBGA | Intel
MPN: EPM240GF100C5N ✓ فعالEPM240GF100C5N جائزہ
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL macro-cell arrays with a programmable interconnect matrix. In the broader taxonomy, a CPLD sits between simple SPLDs (PAL/GAL) and high-density FPGAs, offering deterministic timing, instant-on behavior, and robust I/O drive strength. MAX II devices belong to Intel's low-power, instant-on CPLD family, commonly used for glue logic, bus bridging, power sequencing, and I/O expansion in systems where FPGAs would be over-specified or too expensive.
Key specifications include 192 logic elements (macro cells), 4.7 ns tPD (fastest pin-to-pin delay), 201.1 MHz internal operation, 80 user I/Os, in-system programmability via JTAG, and 1.8 V core with 1.5-3.3 V VCCIO. The device integrates 8 Kbits of user Flash memory, supports hot-socketing, and provides multi-voltage I/O standards including LVCMOS, LVTTL, and PCI compliance. Compared with earlier MAX 7000-series parts, MAX II cuts static power by an order of magnitude.
Architecturally, the EPM240GF100C5N uses a Logic Array Block (LAB) structure of 16 macro cells each, with a fast interconnect matrix and a non-volatile Flash configuration block that eliminates the external boot PROM. The on-board JTAG interface is IEEE 1149.1 compliant and supports the Jam STAPL programming standard for in-field updates. The 100-ball FBGA at 11 x 11 mm, 1.0 mm pitch, supports surface-mount assembly on standard reflow profiles.
Typical applications include power-up sequencing controllers, I/O voltage translation between 3.3 V and 1.8 V logic domains, peripheral bus bridges (for example, legacy parallel buses to SPI or I2C), LED and display multiplexing drivers, and address decoding in microcontroller-based designs. Designers favor MAX II when deterministic timing, instant-on, and low quiescent power are required without the cost or complexity of an FPGA.
When designing with this device, pay attention to the multi-bank VCCIO supply pins: each I/O bank can operate at an independent 1.5/1.8/2.5/3.3 V level, but unused banks must still be tied to a valid supply voltage to keep the inputs in a defined state. Configure the device with Quartus II (legacy) or the Intel Quartus Prime Lite edition toolchain, and verify pin assignments against the FBGA-100 package diagram before PCB layout.
کے لیے ڈراپ اِن متبادل EPM240GF100C5N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM240GF100C5N (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, RoHS Status, Configuration Memory, Operating Temperature, Programming Interface.
EPM240F100I5N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM240F100C5N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM240F100C4N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM240GF100C5
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPM240F100C4N
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM1270F256C5N
✅ ڈراپ-اِن✗ اسٹاک سے باہر
$16.2 / یونٹ
ڈیٹا شیٹ دیکھیں →EPM240GF100C5N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Family | MAX II |
| Logic Elements / Macro Cells | 192 macro cells |
| Pin-to-Pin Logic Delay (tPD) | 4.7 ns |
| Maximum Operating Frequency | 201.1 MHz |
| User I/Os | 80 |
| Logic Family | CMOS |
| Process Technology | 0.18 um |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Supply Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| User Flash Memory | 8 Kbits |
| پیکیج | 100-ball FBGA (11 x 11 mm, 1.0 mm pitch) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| آپریٹنگ درجہ حرارت | -40 C to +125 C |
| Programming Interface | JTAG (IEEE 1149.1) / Jam STAPL |
| Configuration Memory | On-chip non-volatile Flash |
| RoHS اسٹیٹس | Lead Free, RoHS compliant |
EPM240GF100C5N پن کنفیگریشن
| پن A1 | I/O — User I/O bank 1 |
| پن A2 | I/O — User I/O bank 1 |
| پن A3 | VCCIO1 — I/O bank 1 supply voltage |
| پن A4 | I/O — User I/O bank 1 |
| پن A5 | I/O — User I/O bank 1 |
| پن A6 | GND — Ground |
| پن A7 | I/O — User I/O bank 2 |
| پن A8 | I/O — User I/O bank 2 |
| پن A9 | VCCIO2 — I/O bank 2 supply voltage |
| پن A10 | I/O — User I/O bank 2 |
| پن B1 | I/O — User I/O bank 1 |
| پن B2 | I/O — User I/O bank 1 |
| پن B3 | GND — Ground |
| پن B4 | I/O — User I/O bank 1 |
| پن B5 | I/O — User I/O bank 1 |
| پن B6 | VCCINT — Core 1.8 V supply |
| پن B7 | I/O — User I/O bank 2 |
| پن B8 | I/O — User I/O bank 2 |
| پن B9 | GND — Ground |
| پن B10 | I/O — User I/O bank 2 |
| پن C1 | I/O — User I/O bank 1 |
| پن C2 | VCCIO1 — I/O bank 1 supply voltage |
| پن C3 | I/O — User I/O bank 1 |
| پن C4 | GND — Ground |
| پن C5 | I/O — User I/O bank 1 |
| پن C6 | I/O — User I/O bank 2 |
| پن C7 | GND — Ground |
| پن C8 | I/O — User I/O bank 2 |
| پن C9 | VCCIO2 — I/O bank 2 supply voltage |
| پن C10 | I/O — User I/O bank 2 |
| پن D1 | I/O — User I/O bank 3 |
| پن D2 | I/O — User I/O bank 3 |
| پن D3 | I/O — User I/O bank 3 |
| پن D4 | VCCIO3 — I/O bank 3 supply voltage |
| پن D5 | I/O — User I/O bank 3 |
| پن D6 | I/O — User I/O bank 4 |
| پن D7 | VCCIO4 — I/O bank 4 supply voltage |
| پن D8 | I/O — User I/O bank 4 |
| پن D9 | I/O — User I/O bank 4 |
| پن D10 | I/O — User I/O bank 4 |
| پن E1 | I/O — User I/O bank 3 |
| پن E2 | GND — Ground |
| پن E3 | I/O — User I/O bank 3 |
| پن E4 | I/O — User I/O bank 3 |
| پن E5 | GND — Ground |
| پن E6 | VCCINT — Core 1.8 V supply |
| پن E7 | I/O — User I/O bank 4 |
| پن E8 | I/O — User I/O bank 4 |
| پن E9 | GND — Ground |
| پن E10 | I/O — User I/O bank 4 |
| پن F1 | I/O — User I/O bank 3 |
| پن F2 | VCCIO3 — I/O bank 3 supply voltage |
| پن F3 | I/O — User I/O bank 3 |
| پن F4 | GND — Ground |
| پن F5 | I/O — User I/O bank 3 |
| پن F6 | I/O — User I/O bank 4 |
| پن F7 | GND — Ground |
| پن F8 | I/O — User I/O bank 4 |
| پن F9 | VCCIO4 — I/O bank 4 supply voltage |
| پن F10 | I/O — User I/O bank 4 |
| پن G1 | I/O — User I/O bank 3 |
| پن G2 | I/O — User I/O bank 3 |
| پن G3 | I/O — User I/O bank 3 |
| پن G4 | VCCIO3 — I/O bank 3 supply voltage |
| پن G5 | I/O — User I/O bank 3 |
| پن G6 | I/O — User I/O bank 4 |
| پن G7 | VCCIO4 — I/O bank 4 supply voltage |
| پن G8 | I/O — User I/O bank 4 |
| پن G9 | I/O — User I/O bank 4 |
| پن G10 | I/O — User I/O bank 4 |
| پن H1 | I/O — User I/O bank 3 |
| پن H2 | GND — Ground |
| پن H3 | I/O — User I/O bank 3 |
| پن H4 | TDI — JTAG Test Data In |
| پن H5 | TMS — JTAG Test Mode Select |
| پن H6 | TCK — JTAG Test Clock |
| پن H7 | TDO — JTAG Test Data Out |
| پن H8 | I/O — User I/O bank 4 |
| پن H9 | GND — Ground |
| پن H10 | I/O — User I/O bank 4 |
| پن J1 | I/O — User I/O bank 1 (DEV_OE / CONFIG) |
| پن J2 | I/O — User I/O bank 1 |
| پن J3 | nCONFIG — Configuration control (pull low to reconfigure) |
| پن J4 | VCCIO1 — I/O bank 1 supply voltage |
| پن J5 | GND — Ground |
| پن J6 | CONF_DONE — Configuration status output |
| پن J7 | nSTATUS — Configuration status output |
| پن J8 | I/O — User I/O bank 2 |
| پن J9 | VCCIO2 — I/O bank 2 supply voltage |
| پن J10 | I/O — User I/O bank 2 |
عام استعمالات
EPM240GF100C5N کے لیے موزوں ہے 7 ایپلیکیشنs: Power-Up Sequencing Controller, Multi-Voltage I/O Voltage Translation Bridge, Address Decoding and Chip-Select Glue Logic, LED Display and Multiplexing Driver, Legacy Bus Bridge (PCI/ISA to Local Bus), Peripheral Expansion in MCU-Based Designs, Industrial Control and IoT Edge Gateways.
Power-Up Sequencing Controller
The EPM240GF100C5N's instant-on Flash configuration boots in microseconds with no external PROM, making it ideal for multi-rail power sequencing in networking switches, servers, and ATCA boards. With 4.7 ns tPD and 80 user I/Os across four independent VCCIO banks (1.5-3.3 V), one CPLD can monitor PG (power-good) signals from 4-6 DC-DC converters and assert enable lines in the correct order. Engineers typically design with a state-machine IP that captures the desired rail-on sequence in less than 50 macro cells, leaving headroom for fault-handling and watchdog logic.
تجویز کردہ
Multi-Voltage I/O Voltage Translation Bridge
Each of the four I/O banks on the EPM240GF100C5N accepts an independent VCCIO of 1.5 V, 1.8 V, 2.5 V, or 3.3 V, enabling bidirectional voltage translation between legacy 3.3 V MCUs and modern 1.8 V SoCs without external level shifters. Combined with 80 user I/Os and 4.7 ns propagation delay, a single device can bridge an 8-bit parallel bus, an SPI port, and an I2C bus between three different voltage domains simultaneously. The non-volatile configuration means no boot delay when the rail comes up, simplifying system bring-up.
تجویز کردہ
Address Decoding and Chip-Select Glue Logic
In microcontroller-based designs with external SRAM, Flash, and peripherals, the EPM240GF100C5N provides deterministic 4.7 ns address decoding to generate chip-select signals faster than software-driven GPIO toggling. The 192 macro cells comfortably hold 6-8 chip-select decoders plus a wait-state generator for slow peripherals, and the JTAG programmability lets designers iterate on decoding tables without board rework. The industrial -40 to +125 C temperature range supports deployment in automotive under-hood and outdoor industrial enclosures.
تجویز کردہ
LED Display and Multiplexing Driver
The EPM240GF100C5N drives multiplexed LED matrices, seven-segment displays, and Charlieplexed arrays with up to 80 outputs and 201 MHz internal performance, well above the scan-rate needs of typical 100-1000 Hz refresh designs. The deterministic 4.7 ns delay supports bit-banged protocols such as WS2812B, APA102, and DMX512 directly from macro-cell state machines, eliminating a dedicated LED driver IC. Flash-based configuration means the animation pattern is retained across power cycles with zero boot latency.
تجویز کردہ
Legacy Bus Bridge (PCI/ISA to Local Bus)
Industrial PCs and factory automation controllers still rely on legacy parallel buses (PCI, ISA, PC/104), and the EPM240GF100C5N bridges these to modern SPI, I2C, or local-bus peripherals. With 4.7 ns tPD and 80 I/Os, the device can implement a 16-bit PCI target state machine plus dual-port SRAM handshaking in under 100 macro cells. The 3.3 V PCI-compliant I/O bank interfaces directly to legacy backplanes, while a 1.8 V bank connects to a modern SoC, all inside one BGA-100 package.
تجویز کردہ
Peripheral Expansion in MCU-Based Designs
When an 8-bit or 32-bit MCU runs out of GPIO, the EPM240GF100C5N adds 80 individually programmable I/Os with edge-triggered interrupts, PWM generators, and quadrature decoders in firmware-upgradable logic. Designers map up to 16 PWM channels at 100 kHz with 10-bit resolution directly into macro-cell state machines, freeing the MCU's CPU cycles for application code. The non-volatile Flash storage means peripheral personality is preserved across brown-out events with no external boot loader required.
تجویز کردہ
Industrial Control and IoT Edge Gateways
In Industry-4.0 edge gateways, the EPM240GF100C5N aggregates sensor data from Modbus, CAN, and RS-485 networks and presents a unified SPI or I2C interface to the host SoC. The deterministic 4.7 ns logic delay ensures protocol timing compliance on CAN (1 Mbps) and RS-485 (10 Mbps) without software jitter. Its industrial -40 to +125 C temperature range, 1.8 V low-power core, and 8 Kbits user Flash for parameter storage make it a workhorse in compact, fan-less gateway enclosures.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM240GF100C5N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM240F100I5N | EPM240F100C5N | EPM240F100C4N | EPM240GF100C5 | EPM1270F256C5N |
|---|---|---|---|---|---|---|
| Package | 100-ball FBGA (11 x 11 mm) | 100-ball FBGA - same | 100-pin TQFP - different | 100-ball FBGA - same | 100-ball FBGA - same (SnPb balls) | 256-ball FBGA - different |
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Macro Cells | 192 | 192 | 192 | 192 | 192 | 1270 |
| Pin-to-Pin Delay (tPD) | 4.7 ns | 4.7 ns | 4.7 ns | ~3.7 ns (-4 speed grade) | 4.7 ns | 6.2 ns |
| User I/Os | 80 | 80 | 80 | 80 | 80 | 212 |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | -40 C to +125 C | -40 C to +100 C (industrial) | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
اہم امتیازی خصوصیات
- Lowest pin-to-pin delay in the MAX II EPM240 family in BGA (بمقابلہEPM240F100C4N)
- Compact 11x11 mm FBGA footprint (بمقابلہEPM240F100C5N)
- Four independent VCCIO banks in a single 100-ball package (بمقابلہEPM1270F256C5N)
- Non-volatile Flash configuration with instant-on (بمقابلہLattice ispMACH 4000 (LC4064ZE))
ڈیزائن نوٹس
The EPM240GF100C5N requires two separate supply rails: a 1.8 V VCCINT for the core logic and one or more VCCIO rails (1.5/1.8/2.5/3.3 V) for the I/O banks. Decouple each VCCINT and VCCIO pin with a 0.1 uF X7R ceramic capacitor placed within 100 mils of the ball, and add a single 10 uF bulk capacitor near the supply entry point. All four VCCIO banks must be powered even if unused - leaving a VCCIO bank floating causes input-pin leakage and indeterminate I/O behavior on power-up.
The 100-ball FBGA at 1.0 mm pitch requires a 4-layer PCB minimum, with the inner layers acting as ground and power planes directly beneath the BGA. Use 0.5 mm via-pad diameter, 0.25 mm via-drill, and microvia-in-pad if budget allows, to route signals out of the inner rows. Match trace impedance to 50 ohms single-ended for clock and JTAG signals, and provide a continuous ground pour under the BGA for thermal dissipation (~1 W max on this 0.18 um part).
Do not confuse the EPM240GF100C5N (FBGA package) with the EPM240F100C5N (TQFP-100 package). Both share the same die but have completely different PCB footprints. Verify the package code on the incoming-receiving inspection label and on the device top marking. Another common mistake is connecting JTAG pins (TDI, TMS, TCK, TDO) directly to a 3.3 V MCU without a level shifter when VCCIO1 is set to 1.8 V - the 3.3 V signals will exceed absolute-max ratings on the I/O bank. Always tie nCONFIG high through a 10 kohm pull-up and provide a push-button to ground for manual reconfiguration.
Although the MAX II CPLD is a relatively slow device by FPGA standards, the simultaneous-switching output (SSO) limit on each VCCIO bank should still be respected. Bank 1 and Bank 3 each support 24 mA drive strength per pin in PCI mode; avoid driving more than 16 outputs simultaneously at full strength to stay within the GND/VCC bounce budget. For clock outputs, use the dedicated CLK input pin and a global clock buffer to minimize skew - software tools like Quartus' fitter report will flag any timing violations automatically.
تعمیل کی معلومات
Lead-free FBGA balls with NiPdAu finish, RoHS compliant per device datasheet. Industrial -40 to +125 C temperature range but not AEC-Q100 qualified for automotive - use automotive-grade MAX V or Cyclone family for AEC-Q100 applications.
