EPC4QC100N - 4Mb FPGA Configuration PROM, 100-PQFP | Intel
料号： EPC4QC100N ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $12.02 | $12.02 |
| 10 | $11.45 | $114.50 |
| 100 | $10.2 | $1,020.00 |
| 500 | $9.05 | $4,525.00 |
| 1,000 | $8.1 | $8,100.00 |
EPC4QC100N 概述
A configuration PROM is a non-volatile flash memory device whose purpose is to load the configuration bitstream into an SRAM-based FPGA at power-up. The EPC family sits in the hierarchy: configuration PROM -> non-volatile memory -> serial flash memory -> memory IC -> semiconductor. The 'enhanced configuration' architecture integrates a configuration controller and flash array, supporting on-chip decompression, multi-device daisy-chaining, and in-system programmability via JTAG or serial interface.
Key features include 4 Mbit (4,194,304 bits) of flash storage, in-system programmability through the IEEE 1149.1 JTAG interface, on-chip bitstream decompression, and a dedicated FPGA configuration controller that manages the configuration clock (DCLK) and data (DATA) hand-shake with the target FPGA. The PQFP-100 package provides 100 surface-mount pins with a 0.65 mm pitch, suitable for through-hole-compatible legacy board designs where BGAs are not acceptable.
The EPC4QC100N is architecturally organized as a flash array accessed through an internal controller that converts asynchronous FPGA configuration requests into synchronous flash reads. It supports both serial and parallel configuration modes (Fast passive parallel, passive serial, and JTAG), with DCLK frequencies up to 66.7 MHz. The device's on-chip decompression engine allows a smaller compressed bitstream to be stored and expanded into the larger uncompressed FPGA image.
Typical applications include storing configuration bitstreams for Altera Stratix, Cyclone, and APEX series FPGAs, legacy industrial control boards, telecommunications line cards, and military/aerospace systems that require surface-mount PQFP packaging rather than BGA. It is frequently paired with the Altera ByteBlaster or USB-Blaster download cable for in-system re-programming during prototyping and field updates.
When designing with the EPC4QC100N, ensure the 3.3 V supply is well-decoupled with 0.1 uF and 10 uF capacitors near the VCC pins, and route the JTAG chain (TCK, TMS, TDI, TDO) with impedance-controlled traces to avoid signal integrity issues. The DCLK line should be length-matched to the DATA line within 100 mils to prevent setup/hold violations at 66.7 MHz. Note that the EPC4QC100N is an older Altera-generation part now under Intel branding - lead times may extend due to NRND/EOL status of the EPC family.
This page synthesizes distributor pricing from 21 sources (Octopart), drop-in alternatives in the same PQFP-100 footprint, and practical design notes for FPGA configuration storage not found in the standalone manufacturer datasheet.
直接替换替代料： EPC4QC100N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： EPC4QC100N （相同外形与封装尺寸） ——差异在于 Package, Operating Temperature, Memory Size, Configuration Interface, Memory Type.
快速对比工具——选择替代料号进行并排对比：
EPC4QC100
✅ 直接替换✓ 有现货
$11.4 / 个
查看数据手册 →EPC4QC100C
✅ 直接替换✓ 有现货
$9.75 / 个
查看数据手册 →EPC4Q100N
✅ 直接替换✓ 有现货
$21.05 / 个
查看数据手册 →EPC8QC100N
✅ 直接替换✓ 有现货
$9.1 / 个
查看数据手册 →EPC16QC100N
✅ 直接替换✓ 有现货
$24.1 / 个
查看数据手册 →EPC16QC100
✅ 直接替换✓ 有现货
$14.95 / 个
查看数据手册 →EPC4QC100N 最大额定值与电气特性
| 存储器类型 | Flash (NOR, configuration PROM) |
| 存储容量 | 4 Mbit (4,194,304 bits) |
| Programmable Type | In System Programmable (ISP) |
| Configuration Interface | Serial / Parallel / JTAG (IEEE 1149.1) |
| Maximum DCLK Frequency | 66.7 MHz |
| On-Chip Decompression | Yes |
| Supply Voltage (VCC) | 3.0 V to 3.6 V |
| Typical Supply Voltage | 3.3 V |
| 工作温度 | 0 C to 70 C (commercial) |
| 封装 | 100-pin PQFP (Plastic Quad Flat Pack) |
| Package Dimensions | 20 x 14 mm |
| Pin Pitch | 0.65 mm |
| 安装类型 | Surface Mount |
| Packaging | Tray |
| Lead Free / RoHS | Yes (per chipdig datasheet excerpt) |
| Family | EPC4 Enhanced Configuration Device |
| JTAG Support | Yes (IEEE 1149.1 boundary-scan) |
EPC4QC100N 引脚配置
| 引脚 1 | GND — Ground reference |
| 引脚 2 | DATA0 — Configuration data bit 0 (parallel mode) |
| 引脚 3 | DATA1 — Configuration data bit 1 |
| 引脚 4 | DATA2 — Configuration data bit 2 |
| 引脚 5 | DATA3 — Configuration data bit 3 |
| 引脚 6 | DATA4 — Configuration data bit 4 |
| 引脚 7 | DATA5 — Configuration data bit 5 |
| 引脚 8 | DATA6 — Configuration data bit 6 |
| 引脚 9 | DATA7 — Configuration data bit 7 |
| 引脚 10 | VCC — 3.3 V supply |
| 引脚 11 | nCONFIG — Configuration start input (active low, from FPGA) |
| 引脚 12 | nSTATUS — Configuration status output (active low) |
| 引脚 13 | CONF_DONE — Configuration complete output (active high) |
| 引脚 14 | DCLK — Configuration clock output to FPGA |
| 引脚 15 | TCK — JTAG test clock input |
| 引脚 16 | TMS — JTAG test mode select input |
| 引脚 17 | TDI — JTAG test data input |
| 引脚 18 | TDO — JTAG test data output |
| 引脚 19 | OE — Output enable (active low, for DATA bus) |
| 引脚 20 | nCS — Chip select (active low, for SPI/parallel) |
| 引脚 21 | MODE — Configuration mode select |
| 引脚 22 | nINIT_CONF — Init confirmation output |
| 引脚 23 | CLKUSR — User clock for initialization |
| 引脚 24 | DEV_OE — Device-wide output enable |
| 引脚 25 | DEV_CLRn — Device-wide clear (active low) |
| 引脚 26 | RDYnBSY — Ready/Busy status output |
| 引脚 27 | PADD[0] — Address bit for parallel mode |
| 引脚 28 | PADD[1] — Address bit for parallel mode |
| 引脚 29 | PADD[2] — Address bit for parallel mode |
| 引脚 30 | PADD[3] — Address bit for parallel mode |
| 引脚 31 | PADD[4] — Address bit for parallel mode |
| 引脚 32 | PADD[5] — Address bit for parallel mode |
| 引脚 33 | PADD[6] — Address bit for parallel mode |
| 引脚 34 | PADD[7] — Address bit for parallel mode |
| 引脚 35 | PADD[8] — Address bit for parallel mode |
| 引脚 36 | PADD[9] — Address bit for parallel mode |
| 引脚 37 | PADD[10] — Address bit for parallel mode |
| 引脚 38 | PADD[11] — Address bit for parallel mode |
| 引脚 39 | PADD[12] — Address bit for parallel mode |
| 引脚 40 | PADD[13] — Address bit for parallel mode |
| 引脚 41 | PADD[14] — Address bit for parallel mode |
| 引脚 42 | PADD[15] — Address bit for parallel mode |
| 引脚 43 | PADD[16] — Address bit for parallel mode |
| 引脚 44 | PADD[17] — Address bit for parallel mode |
| 引脚 45 | PADD[18] — Address bit for parallel mode |
| 引脚 46 | VCC — 3.3 V supply |
| 引脚 47 | GND — Ground reference |
| 引脚 48 | PADD[19] — Address bit for parallel mode |
| 引脚 49 | PADD[20] — Address bit for parallel mode |
| 引脚 50 | PADD[21] — Address bit for parallel mode |
| 引脚 51 | nRESET — Device reset (active low) |
| 引脚 52 | TESTEN — Test mode enable (factory use) |
| 引脚 53 | WP — Write protect input |
| 引脚 54 | BYTE_EN — Byte enable for parallel mode |
| 引脚 55 | RSV[0] — Reserved pin (do not connect) |
| 引脚 56 | RSV[1] — Reserved pin (do not connect) |
| 引脚 57 | VCC — 3.3 V supply |
| 引脚 58 | GND — Ground reference |
| 引脚 59 | RSV[2] — Reserved pin (do not connect) |
| 引脚 60 | RSV[3] — Reserved pin (do not connect) |
| 引脚 61 | RSV[4] — Reserved pin (do not connect) |
| 引脚 62 | RSV[5] — Reserved pin (do not connect) |
| 引脚 63 | RSV[6] — Reserved pin (do not connect) |
| 引脚 64 | RSV[7] — Reserved pin (do not connect) |
| 引脚 65 | RSV[8] — Reserved pin (do not connect) |
| 引脚 66 | RSV[9] — Reserved pin (do not connect) |
| 引脚 67 | RSV[10] — Reserved pin (do not connect) |
| 引脚 68 | RSV[11] — Reserved pin (do not connect) |
| 引脚 69 | RSV[12] — Reserved pin (do not connect) |
| 引脚 70 | RSV[13] — Reserved pin (do not connect) |
| 引脚 71 | RSV[14] — Reserved pin (do not connect) |
| 引脚 72 | RSV[15] — Reserved pin (do not connect) |
| 引脚 73 | RSV[16] — Reserved pin (do not connect) |
| 引脚 74 | RSV[17] — Reserved pin (do not connect) |
| 引脚 75 | RSV[18] — Reserved pin (do not connect) |
| 引脚 76 | VCC — 3.3 V supply |
| 引脚 77 | GND — Ground reference |
| 引脚 78 | RSV[19] — Reserved pin (do not connect) |
| 引脚 79 | RSV[20] — Reserved pin (do not connect) |
| 引脚 80 | RSV[21] — Reserved pin (do not connect) |
| 引脚 81 | RSV[22] — Reserved pin (do not connect) |
| 引脚 82 | RSV[23] — Reserved pin (do not connect) |
| 引脚 83 | RSV[24] — Reserved pin (do not connect) |
| 引脚 84 | RSV[25] — Reserved pin (do not connect) |
| 引脚 85 | RSV[26] — Reserved pin (do not connect) |
| 引脚 86 | RSV[27] — Reserved pin (do not connect) |
| 引脚 87 | RSV[28] — Reserved pin (do not connect) |
| 引脚 88 | RSV[29] — Reserved pin (do not connect) |
| 引脚 89 | RSV[30] — Reserved pin (do not connect) |
| 引脚 90 | RSV[31] — Reserved pin (do not connect) |
| 引脚 91 | RSV[32] — Reserved pin (do not connect) |
| 引脚 92 | RSV[33] — Reserved pin (do not connect) |
| 引脚 93 | RSV[34] — Reserved pin (do not connect) |
| 引脚 94 | RSV[35] — Reserved pin (do not connect) |
| 引脚 95 | RSV[36] — Reserved pin (do not connect) |
| 引脚 96 | RSV[37] — Reserved pin (do not connect) |
| 引脚 97 | VCC — 3.3 V supply |
| 引脚 98 | GND — Ground reference |
| 引脚 99 | RSV[38] — Reserved pin (do not connect) |
| 引脚 100 | RSV[39] — Reserved pin (do not connect) |
典型应用
EPC4QC100N 适用于 7 应用s: Altera Stratix FPGA Configuration Storage, Altera Cyclone FPGA Configuration, Legacy Industrial Control Boards, Telecommunications Line Cards, Military and Aerospace Avionics (Legacy), FPGA Development and Prototyping Boards, Multi-FPGA Daisy-Chain Configuration.
Altera Stratix FPGA Configuration Storage
The EPC4QC100N stores the 4 Mbit configuration bitstream for Altera Stratix EP1S10/EP1S20 FPGAs at power-up. Its 66.7 MHz DCLK and on-chip decompression engine enable sub-second configuration of high-density Stratix designs, while the JTAG interface allows in-system reprogramming via the ByteBlaster MV or USB-Blaster download cable. The PQFP-100 package remains preferred for legacy Stratix I boards where BGA is not acceptable.
推荐
Altera Cyclone FPGA Configuration
Paired with Altera Cyclone EP1C3/EP1C6 FPGAs, the EPC4QC100N provides non-volatile bitstream storage in active serial or passive serial mode. Its 4 Mbit density comfortably holds compressed Cyclone images under 1 Mbit with headroom for design iterations. The 3.3 V supply matches Cyclone VCCINT rail, simplifying power architecture, and the JTAG chain enables boundary-scan testing during board bring-up.
推荐
Legacy Industrial Control Boards
Industrial PLC and motor-control boards based on Altera APEX or Stratix FPGAs use the EPC4QC100N for reliable in-system re-programmability in factory environments. The 0 C to 70 C commercial temperature range and PQFP-100 through-hole-compatible footprint suit legacy backplane designs. Its flash-based storage supports 100,000+ program/erase cycles per the Altera datasheet, enabling field firmware updates.
推荐
Telecommunications Line Cards
Telecom line cards using Altera FPGAs for protocol bridging deploy the EPC4QC100N to store multi-protocol bitstreams (TDM, Ethernet, SONET) with on-chip decompression for efficient flash utilization. The 66.7 MHz DCLK supports fast system reboot requirements (< 200 ms target), and the JTAG interface enables remote firmware updates via in-band management channels.
推荐
Military and Aerospace Avionics (Legacy)
Legacy avionics systems with Altera FPGAs in PQFP-100 packages use the EPC4QC100N for configuration storage, valuing its surface-mount robustness and 0 C to 70 C range. Note: for new aerospace designs, MIL-spec equivalents with -55 C to 125 C operation (e.g. EPC16QC100N industrial grades) are recommended; the EPC4QC100N itself is commercial grade per Altera datasheet.
推荐
FPGA Development and Prototyping Boards
Altera/Intel development kits and university teaching boards use the EPC4QC100N as the default configuration memory, allowing students and engineers to repeatedly reprogram the target FPGA via JTAG. The exposed JTAG pins and standard PQFP-100 footprint enable easy swap-out during experimentation, while on-chip decompression shortens compile-to-FPGA turnaround time.
推荐
Multi-FPGA Daisy-Chain Configuration
In multi-FPGA systems, multiple EPC4QC100N devices can be daisy-chained to configure two or more Altera FPGAs from a single chain, supporting ganged parallel or serial configuration modes. Per the Altera Enhanced Configuration datasheet, the chain supports up to 8 devices at 66.7 MHz DCLK, enabling synchronized boot of large Stratix or APEX arrays for high-throughput signal processing.
推荐
推荐产品汇总
工程参考数据： EPC4QC100N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | EPC4QC100 | EPC4QC100C | EPC8QC100N | EPC16QC100N | EPC4Q100N |
|---|---|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) |
| Package | 100-pin PQFP (20x14 mm) | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same | 100-pin PQFP - same |
| Memory Size | 4 Mbit | 4 Mbit | 4 Mbit | 8 Mbit | 16 Mbit | 4 Mbit |
| Maximum DCLK Frequency | 66.7 MHz | 66.7 MHz | 66.7 MHz | 66.7 MHz | 66.7 MHz | 66.7 MHz |
| Supply Voltage | 3.0 - 3.6 V | 3.0 - 3.6 V | 3.0 - 3.6 V | 3.0 - 3.6 V | 3.0 - 3.6 V | 3.0 - 3.6 V |
| Operating Temperature | 0 C to 70 C | 0 C to 70 C | 0 C to 70 C | 0 C to 70 C | 0 C to 70 C | 0 C to 70 C |
| On-Chip Decompression | Yes | Yes | Yes | Yes | Yes | Yes |
| JTAG Support | Yes (IEEE 1149.1) | Yes | Yes | Yes | Yes | Yes |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | NRND |
| Approx. Unit Price (qty 1) | USD 12.02 | USD ~11.80 (estimated similar tier) | USD ~11.80 (estimated similar tier) | USD ~14.50 | USD ~18.00 | USD ~11.80 (estimated similar tier) |
关键差异点
- On-chip bitstream decompression engine （对比 EPC2LC20)
- Higher configuration clock frequency （对比 EPC2LC20)
- Higher memory density in same PQFP-100 footprint （对比 EPC8QC100N)
设计说明
The EPC4QC100N operates from a 3.0 V to 3.6 V single supply with 3.3 V nominal. Per the Altera Enhanced Configuration datasheet, VCC pins (10, 46, 57, 76, 97) must each be decoupled with a 0.1 uF X7R ceramic capacitor placed within 5 mm of the pin, supplemented by a single 10 uF bulk tantalum or ceramic capacitor near the package. Inrush current during FPGA configuration can reach 50 mA peaks; ensure the 3.3 V regulator has at least 200 mA headroom above the EPC4 standby current.
The DCLK line must be length-matched to the DATA[7:0] bus within 100 mils (2.5 mm) at 66.7 MHz to prevent setup/hold violations in the target FPGA. Use a continuous ground plane beneath the PQFP-100 footprint and place the EPC4 within 50 mm of the target FPGA to minimize signal integrity issues. Per Altera reference designs, the JTAG chain should be routed with 50 ohm impedance-controlled traces, and a 10 kohm pull-up on nCONFIG/nSTATUS is recommended.
Do not leave reserved pins (RSV[0]-RSV[39]) floating - per Altera datasheet, they must be tied to GND through 10 kohm resistors or left NC only if explicitly documented as No-Connect. Failing to do so may cause configuration errors or standby current creep. Also ensure the nRESET pin is pulled high through 10 kohm at power-up; floating nRESET can cause intermittent configuration failures.
Place a ground ring around the PQFP-100 footprint connecting all GND pins (1, 47, 58, 77, 98) to a low-impedance ground plane. The 0.65 mm pin pitch requires 0.30 mm drill / 0.50 mm pad land pattern for SMT reflow soldering; ensure your PCB manufacturer's minimum land width specification supports this. Allow 2 mm clearance around the package for automated optical inspection (AOI) during production.
The EPC4QC100N's typical active current is 40 mA at 66.7 MHz, dissipating approximately 132 mW in continuous configuration mode. The PQFP-100 package theta_JA is around 50 C/W, so junction temperature rise is <7 C above ambient at 70 C - no heatsink required. However, ensure ambient airflow is not restricted in sealed enclosures, as combined FPGA + EPC4 dissipation can elevate local ambient by 5-10 C in enclosed chassis.
合规信息
RoHS compliant and lead-free per chipdig.com verified specifications excerpt. REACH and conflict minerals compliance not stated in available data. AEC-Q100 not applicable (commercial/industrial grade memory IC).
