بەرهەمەکان (3,200+)

LM2904NG - Dual Op Amp, 1MHz, 3-26V, PDIP-8 | onsemi
LM2904NG

LM2904NG - Dual Op Amp, 1MHz, 3-26V, PDIP-8 | onsemi

The onsemi LM2904NG is a general-purpose dual operational amplifier consisting of two independent, internally frequency-compensated op amps in a 400 mil 8-pin PDIP (0.300 in / 7.62 mm row spacing) package. It operates from a single supply of 3V to 26V or from dual supplies, delivers a gain bandwidth product of 1 MHz and a slew rate of 0.6 V/µs, and is rated for operation from -40C to +105C. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output that, together with resistors or capacitors in a feedback network, implements amplification, filtering, comparison, buffering and mathematical functions. The op amp sits at the core of the analog signal-chain hierarchy: amplifier IC -> analog front end -> mixed-signal system. The LM2904 family is the industry-standard dual op amp lineage originally popularized by National Semiconductor and carried forward by multiple manufacturers, including onsemi and Texas Instruments. Key features include a common-mode input voltage range that extends to ground/VEE, enabling the device to sense signals near 0V in single-supply systems, low power drain, and internal frequency compensation that eliminates external compensation components. Single-supply or split-supply operation gives designers flexibility across battery-powered and industrial 24V-class rails. The through-hole PDIP package suits prototyping, repair, education and legacy industrial boards. Architecturally, the LM2904NG uses circuit designs perfected for quad operational amplifiers, packaged as two channels sharing one bias network. Internally compensated pole-splitting keeps the device unity-gain stable without external capacitors, while the class-AB output stage sources and sinks modest load currents. Care is required when sinking current near ground with a single supply, since the output sinks through the ground return path and low-side saturation behavior limits accuracy near 0V on the output swing. Typical applications include transducer amplifiers and sensor front ends, DC gain blocks and active filters, and conventional op amp circuits in industrial control, automotive-adjacent electronics and instrumentation where the -40C to +105C ambient range and ground-sensing inputs are required. Design consideration: in single-supply configurations, bias inputs above the input common-mode floor and avoid driving the output into deep saturation, because recovery from output saturation introduces overshoot and gain errors; decouple the supply pin with 0.1uF close to pin 8. This page synthesizes distributor availability, drop-in alternatives and practical design guidance not found in the manufacturer datasheet, giving engineers a single decision-ready reference.

RFQ پەیوەندی
LM2904P - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P

LM2904P - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904P is a dual, general-purpose operational amplifier designed for single- or dual-supply operation up to 26 V, with a 700 kHz gain-bandwidth product and two amplifiers per package. The LM2904P is supplied in an 8-pin PDIP package, making it suitable for through-hole industrial, instrumentation, and control designs. According to the Texas Instruments product page, the device is a standard dual operational amplifier rather than a low-noise or precision amplifier. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. In a closed-loop configuration, external feedback components define the gain, bandwidth, filtering, and signal behavior. The LM2904P belongs to the broader hierarchy of operational amplifier, analog amplifier, and semiconductor, while its dual configuration saves board area by placing two amplifiers in one package. The verified manufacturer information identifies a maximum 26 V supply-related range and 700 kHz performance. The package is 8-PDIP. Texas Instruments describes the LM2904 as an industry-standard dual operational amplifier family, but the supplied verified data does not include a complete electrical parameter table. Consequently, input offset voltage, input bias current, output current, noise, common-mode range, slew rate, operating temperature, and exact electrical limits are marked as data needed rather than inferred. LM2904P circuits are commonly considered for sensor amplification, buffered analog signals, low-frequency active filters, and general-purpose control loops. Because it is a standard dual amplifier in a through-hole package, it is especially useful for prototypes, educational boards, legacy equipment, and industrial control systems where DIP packaging simplifies manual assembly and inspection. The second amplifier can mirror the first stage, provide filtering, buffer an output, or implement another independent channel. Designers should verify supply polarity, input common-mode limits, output swing, stability with the selected load, and capacitor values against the full manufacturer datasheet before production use. Decoupling capacitors should be placed close to the supply pins, and feedback components should be kept compact to reduce parasitic capacitance. If low-noise, rail-to-rail input/output, high-frequency, or automotive-qualified performance is required, a different amplifier family should be selected after reviewing the complete electrical data. This page consolidates the verified Texas Instruments product description, distributor identification, and package information with engineering guidance, comparison points, and procurement-oriented details for LM2904P users.

RFQ پەیوەندی
LM2904P-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P-MAND

LM2904P-MAND - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904P-MAND is a dual, general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, and 700 kHz gain-bandwidth performance in an 8-pin PDIP package. The device is intended for industrial and automotive control systems operating from a single power supply. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two independent, internally frequency-compensated amplifiers, making it suitable for signal conditioning, feedback-control loops, sensor interfaces, and general-purpose analog signal processing. As a dual amplifier, it can implement two functions in one package while reducing board area and component count. The 26 V supply rating supports higher-voltage industrial and automotive systems than common low-voltage operational amplifiers. A 700 kHz gain-bandwidth figure provides useful bandwidth for general-purpose control and conditioning tasks. The manufacturer identifies the LM2904 family for automotive and industrial control applications, while the standard general-purpose amplifier classification supports use across conventional analog designs. Each amplifier has its own input and output pins, allowing the two sections to operate independently. Internal frequency compensation simplifies closed-loop implementation without requiring an external compensation network. This makes the device suitable for noninverting and inverting amplifiers, voltage followers, comparators, differential stages, transimpedance functions, and active-filter building blocks where appropriate stability and bandwidth requirements are met. Common applications include transducer signal conditioning, closed-loop actuator control, low-side current sensing, buffered sensor inputs, and general industrial instrumentation. The dual configuration can also reduce the number of packages in designs requiring two independent amplifier channels, such as a sensor front end paired with a control or output-conditioning channel. PCB design should preserve the standard 8-pin PDIP footprint and route high-impedance input signals away from switching nodes and output pins. Stable operation depends on suitable feedback compensation, source impedance, load capability, bypass capacitors, and supply decoupling. The LM2904P-MAND is best selected when its 26 V supply capability and dual channel count match the system while its 700 kHz bandwidth is adequate for the intended signal or control loop. This page combines the manufacturer product specifications with application guidance, pin mapping, verified-source links, and practical drop-in comparison data. It is designed to help engineers identify the correct operational-amplifier footprint, evaluate supply and bandwidth requirements, and plan PCB integration without relying on generic dual-op-amp assumptions.

RFQ پەیوەندی
LM2904P3 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904P3

LM2904P3 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904P3 is a dual general-purpose operational amplifier with two amplifier circuits, a 26 V maximum supply rating, 700 kHz gain-bandwidth performance, and an 8-pin PDIP package. It is designed for conventional analog signal-conditioning applications where a wide supply-voltage range and two amplifiers per package are useful. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between signals applied to its inverting and non-inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers, general-purpose amplifiers, instrumentation amplifiers, and precision amplifiers. Two amplifiers in one package can reduce board area when a circuit needs matched functions such as buffering, amplification, filtering, or differential sensing. The verified manufacturer information identifies the LM2904 as a dual, 26 V, 700 kHz operational amplifier. The LM2904P3 orderable is identified as a general-purpose, two-circuit amplifier in an 8-PDIP package. Its dual configuration allows both amplifier sections to share one package while retaining independent inputs and outputs. The 26 V rating permits operation from higher-voltage analog systems than typical low-voltage mixed-signal amplifier families. The 700 kHz gain-bandwidth figure defines the practical frequency range for many small-signal applications. It is relevant when closing an amplifier around a feedback network, because the amplifier must provide adequate loop gain and phase margin at the intended signal frequency. General-purpose performance makes the device suitable for signal amplification, voltage buffering, active filtering, and feedback-control stages where specialized precision or high-speed parameters are not required. Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, analog control loops, and general instrumentation. In a dual-amplifier circuit, one section can perform signal conditioning while the other supplies inversion, feedback, or buffering. The package is also appropriate for through-hole industrial designs where DIP mounting remains preferable to fine-pitch surface-mount assembly. Designers should verify the complete electrical limits, electrical characteristics, pin configuration, common-mode range, output swing, input bias current, slew rate, and stability requirements in the manufacturer datasheet before finalizing a design. Decoupling, input and output signal limits, common-mode voltage, and thermal conditions must be evaluated for the exact operating environment. This page consolidates the verified 26 V and 700 kHz device facts, distributor pricing information, package data, and same-family replacement guidance. It also adds practical selection criteria and design notes that help engineers distinguish a true 8-pin drop-in option from alternatives requiring a different footprint.

RFQ پەیوەندی
LM2904PS-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PS-MAND

LM2904PS-MAND - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904PS-MAND is a dual general-purpose operational amplifier in an 8-pin SO package, combining two amplifiers with a 26 V maximum supply rating and 700 kHz gain-bandwidth capability. It is intended for general-purpose analog signal conditioning where a wide supply-voltage range, dual-channel configuration, and compact surface-mount footprint are useful. The MAND ordering code identifies the Texas Instruments LM2904PS device configuration in bulk packaging. An operational amplifier is an active analog component that amplifies the voltage difference between its inverting and non-inverting inputs. High-gain internal stages, negative feedback, and an output stage convert a small differential input into an amplified output. The dual format provides two amplifiers in one package, allowing a design to implement gain stages, buffers, comparators, active filters, or instrumentation circuits while reducing board area. The LM2904 family is specified for general-purpose signal conditioning rather than low-noise precision or high-speed applications. Its two-amplifier configuration supports complementary inverting and non-inverting paths within a single board footprint. The 26 V supply rating supports operation from conventional dual-supply rails used in industrial control, analog instrumentation, and educational electronics, while the 700 kHz gain-bandwidth figure defines its small-signal bandwidth capability. Typical uses include audio preamplifier stages, sensor-conditioning front ends, active filters, DC amplifiers, and general laboratory instrumentation. The dual channel also allows one amplifier to provide gain while the other performs buffering or feedback-path functions. Because the device is a general-purpose part, input-common-mode range, output-swing limits, input-offset voltage, input-bias current, noise characteristics, and slew rate should be checked against the circuit requirements before layout begins. When implementing the LM2904PS-MAND, place bypass capacitors close to the supply pins, route feedback traces away from noisy input paths, and provide stable reference and feedback networks. The 8-pin SO package permits straightforward PCB assembly and standard surface-mount inspection. Bulk packing makes the device suitable for production runs that do not require reel-fed component handling. This page consolidates the manufacturer product information, device-ordering details, package data, cross-reference candidates, application guidance, and PCB-level design notes into one engineering-focused reference for evaluating the LM2904PS-MAND.

RFQ پەیوەندی
LM2904PT - Dual Low Power Op-Amp, TSSOP-8 | STMicroelectronics
LM2904PT

LM2904PT - Dual Low Power Op-Amp, TSSOP-8 | STMicroelectronics

The STMicroelectronics LM2904PT is a low-power dual operational amplifier consisting of two independent, internally frequency-compensated op-amps in an 8-pin TSSOP (PT) package. It operates from supply voltages up to 30 V (single-supply) or +/-15 V (dual-supply) and integrates two general-purpose amplifier circuits per package. A dual operational amplifier is a voltage-regulating analog IC that amplifies the difference between two input terminals while providing high input impedance and low output impedance. Within the amplifier hierarchy, it sits at the general-purpose op-amp level - a subcategory of linear amplifier ICs within the broader analog signal-conditioning and power management semiconductor families. Dual op-amps are preferred where two gain stages or filters are needed in one footprint, saving board space and BOM cost. Key features of the LM2904PT include single-supply operation with input common-mode range that includes ground, internally compensated unity-gain stability, and a 1.1 MHz gain-bandwidth per the device comparisons published by distributors. The wide supply range of 30 V supports industrial 24 V rails directly, which is the main reason the LM2904 family dominates industrial and automotive signal-conditioning sockets. Architecturally, the device is a bipolar (bipolar junction transistor) design, as ST describes it as a low power bipolar op-amp. Bipolar process technology gives robust ESD tolerance and predictable behavior over temperature, at the cost of higher quiescent current than CMOS alternatives. The two amplifiers share bias circuitry, so total supply current is lower than two single op-amps. Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators in non-critical precision roles, motor-control sensing circuits, and general industrial signal conditioning. The single-supply, ground-sensing input is especially convenient for battery-powered and 24 V industrial systems where a negative rail is unavailable. For design, note that the output stage cannot swing fully to the positive rail - reserve headroom on the high side, and avoid driving the output into deep saturation if fast recovery is needed. Input offset voltage limits use in precision DC measurement; select a precision op-amp for microvolt-level applications. This page synthesizes distributor cross-references, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
LM2904PW - Dual 700 kHz Op Amp, 26 V | Texas Instruments
LM2904PW

LM2904PW - Dual 700 kHz Op Amp, 26 V | Texas Instruments

The Texas Instruments LM2904PW is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum supply capability, and an 8-pin TSSOP package. The device contains two independent, frequency-compensated amplifiers that can operate from a single supply or split supply, making it suitable for signal conditioning, buffering, and general-purpose analog control applications. Its 0.7 mA typical supply-current drain is specified as being independent of supply voltage, helping conserve power across a broad operating range. An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual op amp combines two amplifiers in one package, allowing both channels to share a supply while remaining electrically independent. Within the broader semiconductor hierarchy, the LM2904PW belongs to the amplifier IC, operational-amplifier, analog-signal-conditioning, and integrated-circuit families. It is a widely recognized general-purpose alternative to newer precision and low-noise amplifier families when voltage range, low power, and functional simplicity matter more than low offset or rail-to-rail operation. The principal operating characteristics include a 26 V maximum supply voltage, a 700 kHz gain-bandwidth product, two amplifier circuits, and a typical supply-current drain of 0.7 mA. The common-mode input range includes ground, allowing the device to sense input signals close to the negative supply rail. Low input-bias and input-offset parameters are identified in the device literature, although exact minimum and maximum limits are not included in the retrieved data. The LM2904PW therefore provides a practical balance of gain bandwidth, supply flexibility, and low supply-current demand. Internally, the LM2904 uses a frequency-compensated voltage-feedback architecture. This internal compensation means each amplifier can provide stable closed-loop operation without an external frequency-compensation network when configured for typical noninverting or inverting gains. The design is intended for general-purpose analog systems rather than precision instrumentation. Its 700 kHz gain-bandwidth product is adequate for audio-frequency signal conditioning, low-rate data acquisition, sensor interfaces, and industrial control blocks, but it is substantially slower than precision, high-speed, or rail-to-rail amplifier families. Typical uses include general-purpose signal amplification, low-frequency active filtering, current-to-voltage conversion for sensors, audio preamplification, comparator-style threshold conditioning with suitable output limits, and industrial control interfaces. The ability to operate from single or split supplies makes the part useful in systems whose signal range is referenced to ground. For battery-powered equipment, the typical 0.7 mA supply-current drain helps limit consumption, although the complete system current also depends on output current, load, amplifier configuration, and supply voltage. Designers should verify the exact common-mode, output-swing, offset-voltage, input-bias-current, slew-rate, and temperature limits from the manufacturer datasheet before fixing operating conditions. Input and output stability depends on layout, source impedance, load, and feedback topology. Decoupling should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance and leakage around high-impedance inputs. The 8-pin TSSOP footprint is compact but requires careful lead pitch and thermal considerations during assembly. This product record combines the verified manufacturer identity, package, voltage, bandwidth, and power information with distributor pricing and cross-reference evidence. It also adds practical application guidance, honest substitution limits, package-level comparison data, and design notes intended to help engineers evaluate the LM2904PW beyond a raw distributor listing.

RFQ پەیوەندی
LM2904PWR - Dual 700 kHz Op Amp, 26 V | Texas Instruments (Tape & Reel)
LM2904PWR

LM2904PWR - Dual 700 kHz Op Amp, 26 V | Texas Instruments (Tape & Reel)

The Texas Instruments LM2904PWR is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum supply capability, and an 8-pin TSSOP package. The device contains two independent, frequency-compensated amplifiers that can operate from a single supply or split supply, making it suitable for signal conditioning, buffering, and general-purpose analog control applications. Its 0.7 mA typical supply-current drain is specified as being independent of supply voltage, helping conserve power across a broad operating range. An operational amplifier, or op amp, is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. A dual op amp combines two amplifiers in one package, allowing both channels to share a supply while remaining electrically independent. Within the broader semiconductor hierarchy, the LM2904PWR belongs to the amplifier IC, operational-amplifier, analog-signal-conditioning, and integrated-circuit families. It is a widely recognized general-purpose alternative to newer precision and low-noise amplifier families when voltage range, low power, and functional simplicity matter more than low offset or rail-to-rail operation. The principal operating characteristics include a 26 V maximum supply voltage, a 700 kHz gain-bandwidth product, two amplifier circuits, and a typical supply-current drain of 0.7 mA. The common-mode input range includes ground, allowing the device to sense input signals close to the negative supply rail. Low input-bias and input-offset parameters are identified in the device literature, although exact minimum and maximum limits are not included in the retrieved data. The LM2904PWR therefore provides a practical balance of gain bandwidth, supply flexibility, and low supply-current demand. Internally, the LM2904 uses a frequency-compensated voltage-feedback architecture. This internal compensation means each amplifier can provide stable closed-loop operation without an external frequency-compensation network when configured for typical noninverting or inverting gains. The design is intended for general-purpose analog systems rather than precision instrumentation. Its 700 kHz gain-bandwidth product is adequate for audio-frequency signal conditioning, low-rate data acquisition, sensor interfaces, and industrial control blocks, but it is substantially slower than precision, high-speed, or rail-to-rail amplifier families. Typical uses include general-purpose signal amplification, low-frequency active filtering, current-to-voltage conversion for sensors, audio preamplification, comparator-style threshold conditioning with suitable output limits, and industrial control interfaces. The ability to operate from single or split supplies makes the part useful in systems whose signal range is referenced to ground. For battery-powered equipment, the typical 0.7 mA supply-current drain helps limit consumption, although the complete system current also depends on output current, load, amplifier configuration, and supply voltage. Designers should verify the exact common-mode, output-swing, offset-voltage, input-bias-current, slew-rate, and temperature limits from the manufacturer datasheet before fixing operating conditions. Input and output stability depends on layout, source impedance, load, and feedback topology. Decoupling should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance and leakage around high-impedance inputs. The 8-pin TSSOP footprint is compact but requires careful lead pitch and thermal considerations during assembly. This product record combines the verified manufacturer identity, package, voltage, bandwidth, and power information with distributor pricing and cross-reference evidence. It also adds practical application guidance, honest substitution limits, package-level comparison data, and design notes intended to help engineers evaluate the LM2904PWR beyond a raw distributor listing.

RFQ پەیوەندی
LM2904PWRE4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRE4

LM2904PWRE4 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904PWRE4 is a dual general-purpose operational amplifier with two amplifier circuits, a 700 kHz gain-bandwidth product, and operation up to 26 V in an 8-pin TSSOP package. The device supports single-supply or dual-supply operation and provides a 0.3 V/us slew rate. It is packaged for tape-and-reel manufacturing and identified as automotive temperature grade by the manufacturer ordering information. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or amplify a voltage. In the broader semiconductor hierarchy, the LM2904 belongs to the operational-amplifier family within analog amplifiers and signal-chain ICs. Its dual-circuit configuration allows two independent amplifier channels in one package, reducing board area when a design needs general-purpose voltage amplification, buffering, or signal conditioning. The principal operating characteristics are its 26 V maximum supply capability, 700 kHz gain-bandwidth product, and 0.3 V/us slew rate. The 8-TSSOP package measures 0.173 inches, or 4.40 mm, in width according to the component listing. Low supply-current operation independent of supply voltage is also identified in the LM2904 datasheet, making the amplifier suitable for power-conscious analog systems that do not require high-speed precision amplification. The LM2904 uses two independent amplifier sections for general-purpose analog functions. Its bandwidth supports moderate-frequency signal processing rather than high-speed video or RF amplification. A designer should verify gain-bandwidth, slew-rate, output-current capability, input common-mode range, input bias current, and output-voltage swing against the application because those operating limits define whether a conventional non-inverting or inverting topology can meet the required waveform and load conditions. Typical uses include low-frequency sensor conditioning, audio preamplification, current-to-voltage conversion, general feedback control, and analog signal buffering. Because the IC contains two amplifiers, a single package can implement an instrumentation-style signal chain, a dual-channel filter, or a mixed configuration such as an active filter followed by an output driver. The 8-pin TSSOP footprint is also practical for compact mixed-signal boards. PCB implementation should provide a short, low-impedance supply path to the device and route sensitive input and feedback connections away from switching nodes. Decoupling capacitors should be placed close to the supply pins, while input and feedback components should be positioned to minimize parasitic capacitance and leakage. Stable operation also depends on keeping output current and capacitive loading within the limits specified by the manufacturer datasheet. This product page organizes the LM2904PWRE4 specifications, practical application guidance, same-package alternatives, and design considerations into an engineering-focused selection resource. It also highlights where additional device parameters must be checked directly in the manufacturer datasheet before a new analog board is released.

RFQ پەیوەندی
LM2904PWRG3 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRG3

LM2904PWRG3 - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG3 is a dual general-purpose operational amplifier rated for a 26 V maximum total supply voltage and a 700 kHz gain-bandwidth product, supplied in an 8-pin TSSOP package. The device contains two independent, internally frequency-compensated amplifiers, allowing one package to provide two separate analog signal-processing channels. Its 0.3 V/us slew rate supports general-purpose applications requiring stable amplification from low-frequency instrumentation signals. An operational amplifier is a voltage-gain semiconductor that uses high open-loop gain and negative feedback to amplify small voltage differences. The dual-amplifier configuration belongs to the broader hierarchy of analog signal-chain ICs, analog ICs, and semiconductors. Operational amplifiers are commonly used in sensor conditioning, current sensing, error amplifiers, voltage followers, filters, and signal-conversion circuits where a predictable closed-loop response is more important than very high speed. The LM2904PWRG3 is designed for cost-sensitive, general-purpose systems rather than precision or high-speed signal-chain applications. According to the Texas Instruments LM2904 product information, the device is specified as a dual 26 V, 700 kHz operational amplifier. The manufacturer documentation also describes the LM2904 family as providing two independent, high-gain, frequency-compensated amplifiers that can operate from a single supply or split supplies. A low 0.7 mA typical supply-current drain is identified in the device documentation, helping reduce system power consumption when both channels remain active. The wide supply-voltage capability makes the amplifier applicable to industrial control, automotive-style signal conditioning, test equipment, and embedded analog interfaces. Each amplifier can be configured with external resistors or capacitors as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style stage, or active-filter element. Internal frequency compensation removes the need for an external compensation capacitor in ordinary closed-loop configurations, simplifying implementation while preserving stable operation for typical feedback networks. The TSSOP-8 package provides a compact surface-mount footprint suitable for high-density analog boards. Because the device supports single-supply or split-supply operation, the circuit designer must still define the input common-mode range and output swing relative to the selected rails. Input and output voltages must remain within the limits defined by the manufacturer datasheet, and unused amplifier inputs should be biased to prevent undefined operation. This product page combines the verified manufacturer characteristics, package information, sourcing links, application guidance, and drop-in comparison data into an engineering-focused reference. It also highlights where the LM2904PWRG3 is appropriate and where higher precision, wider bandwidth, lower noise, or automotive qualification is required. Review the pin-description table and recommended operating conditions in the manufacturer datasheet before final PCB release or substitution to another dual amplifier.

RFQ پەیوەندی
LM2904PWRG4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904PWRG4

LM2904PWRG4 - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG4 is a dual general-purpose operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-pin TSSOP package. It contains two internally frequency-compensated amplifiers and operates from single or split supplies, making it suitable for cost-sensitive industrial and consumer signal-conditioning designs. An operational amplifier is a high-gain differential amplifier used to compare or amplify small voltage signals. The LM2904 belongs to the operational-amplifier hierarchy, where an op amp forms part of a broader analog and mixed-signal processing system. Its low supply-current consumption, common-mode input range that includes ground, and wide supply-voltage range make it useful in sensor interfaces, buffer stages, audio paths, and low-to-moderate-frequency control loops. The two channels provide approximately 0.3 V/us slew rate, 3 mV typical input offset voltage, 2 nA typical input offset current, and 20 nA typical input bias current. Typical supply-current consumption is 0.7 mA. Internal frequency compensation removes the need for external compensation in conventional closed-loop configurations, while the common-mode range extending toward ground supports direct sensing of signals near the lower supply rail. Each channel can operate independently, allowing simultaneous amplification, filtering, voltage comparison, or buffering. The device includes input-bias-current compensation and differential-input protection through internal clamp structures, supporting operation in conventional industrial control and instrumentation circuits. Designers must still observe the absolute maximum ratings for supply voltage, input voltage, current, junction temperature, and package power dissipation. Typical uses include low-frequency sensor conditioning, 4-20 mA receiver stages, audio preamplification, comparator-based control, active filters, and general-purpose analog interfaces. The dual configuration reduces component count when two independent analog functions are needed, while the compact TSSOP package suits densely assembled control boards. The main design consideration is bandwidth and stability. The 700 kHz gain-bandwidth product and 0.3 V/us slew rate are appropriate for low-frequency precision and general-purpose circuits, but they do not target high-speed signal chains. Check the required closed-loop gain, output swing, load impedance, supply voltage, and input common-mode range against the manufacturer datasheet. This product page combines the device specifications, application guidance, same-footprint alternatives, and engineering-oriented selection considerations. It also identifies where a redesign should focus on supply range, slew rate, precision, or package compatibility rather than treating every dual op amp as an interchangeable replacement.

RFQ پەیوەندی
LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments
LM2904PWRG4-JF

LM2904PWRG4-JF - 26-V Dual Op Amp | Texas Instruments

The Texas Instruments LM2904PWRG4-JF is a dual general-purpose operational amplifier with two independent amplifier channels, a 26 V maximum supply rating, and a 700 kHz gain-bandwidth product in an 8-pin TSSOP package. The -JF ordering code identifies the specified Texas Instruments device, while the PW package contains both channels and their power connections in a compact surface-mount outline. An operational amplifier is a high-gain analog building block used in signal-conditioning, comparison, feedback, filtering, and amplification circuits. In the broader electronics hierarchy, an operational amplifier is a type of analog amplifier IC and belongs to the amplifier and signal-processing category. A dual device contains two amplifier sections in one package, allowing one component to handle two related signals while reducing board area and external component count. The LM2904 family is positioned for general-purpose designs rather than precision or high-speed instrumentation. Its stated 700 kHz gain-bandwidth product gives designers a concrete basis for estimating closed-loop bandwidth at a selected noise gain. The 26 V maximum supply rating provides compatibility with higher-voltage analog systems, while the -40°C to +125°C temperature range supports industrial temperature-range design requirements. Each amplifier can operate with feedback configured for inverting, non-inverting, summing, and other standard analog topologies. Differential input and feedback arrangements determine voltage gain and signal behavior, so the same device can serve as a signal amplifier, comparator when configured for saturation, or an active filter building block. The dual channel count is especially useful when a circuit requires two closely related signal paths, such as a sensor front end and a buffered reference stage. Typical applications include sensor-signal conditioning, control-loop error amplification, audio preamplification, low-frequency active filtering, and general instrumentation. The 700 kHz gain-bandwidth product is most relevant to low-to-moderate-bandwidth closed-loop designs, while the 26 V supply rating is useful when the signal path operates from a higher-voltage rail. Design the surrounding feedback network carefully because resistor and capacitor tolerances directly influence gain, bandwidth, offset behavior, and stability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so they do not float. The TSSOP-8 outline also requires adequate solder-joint formation and thermal spreading for reliable assembly. This product page combines the exact ordering information, principal electrical ratings, package details, drop-in replacement guidance, comparison rows, and application-specific design considerations to support faster component selection and board planning.

RFQ پەیوەندی
LM2904Q2T - Dual 1.1 MHz Op Amp | STMicroelectronics
LM2904Q2T

LM2904Q2T - Dual 1.1 MHz Op Amp | STMicroelectronics

STMicroelectronics LM2904Q2T is a low-power dual bipolar operational amplifier containing two independent, internally frequency-compensated amplifiers. Each channel provides a 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and approximately 100 dB open-loop gain. The device operates from 3 V to 30 V and is supplied in an 8-pin DFN package measuring 2 mm by 2 mm, making it suitable for compact, general-purpose analog signal-processing systems. An operational amplifier is an active analog semiconductor that compares two input voltages and drives its output toward the higher-voltage input. In negative-feedback configurations, it amplifies differential signals while maintaining high input impedance and low output impedance. The LM2904Q2T belongs to the operational-amplifier hierarchy: dual amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Two independent channels allow one package to implement two separate signal paths. Key characteristics include a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 100 dB gain, and low-power bipolar operation. The manufacturer's listed input-current characteristics include 20 nA and 2 nA. Internal frequency compensation simplifies closed-loop amplifier selection, allowing common gains to be implemented without external compensation components. A wide 3 V to 30 V operating range also supports both conventional 5 V analog systems and higher-voltage industrial rails. The two amplifiers operate independently, which prevents signal or output interaction between channels except through their shared supply connections. Both channels use single-ended outputs and share internal frequency compensation. This architecture is appropriate for general-purpose voltage amplification, impedance buffering, comparison, instrumentation, and feedback-control blocks where moderate bandwidth and supply flexibility are more important than low-noise precision or rail-to-rail output operation. Typical applications include sensor-signal conditioning, industrial transducer interfaces, analog control loops, audio preamplifier stages, voltage buffering, and general instrumentation. In a 2 x 2 mm DFN package, the device can reduce board area in designs that can accommodate a land pattern without an exposed thermal pad and maintain adequate copper and assembly process capability. Design with the LM2904Q2T by verifying input common-mode range, output swing, supply current, and capacitive-load stability against the operating point. Keep sensitive-input and feedback routes short, place input and output bypass capacitors close to their associated supply pins, and follow the manufacturer's layout and soldering guidance for the small-pitch DFN footprint. This page combines the exact LM2904Q2T ordering information with electrical characteristics, package constraints, application guidance, a same-package replacement assessment, and practical selection criteria. It also distinguishes confirmed drop-in compatibility from broader functional equivalents so engineers can make footprint-aware design decisions without treating similar amplifier specifications as guaranteed interchangeability.

RFQ پەیوەندی
LM2904QD - Dual 26V 700kHz Automotive Op Amp | Texas Instruments
LM2904QD

LM2904QD - Dual 26V 700kHz Automotive Op Amp | Texas Instruments

Texas Instruments LM2904QD is an automotive-grade, dual operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-terminal gull-wing SOP package. The device contains two general-purpose amplifier sections, allowing one package to support two independent analog signal paths while reducing board area in automotive electronic-control systems. An operational amplifier is an analog amplifier IC that uses high open-loop gain to amplify voltage differences between its non-inverting and inverting inputs. The LM2904 belongs to the broader hierarchy of operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Its dual-channel configuration allows two amplifier sections to be used for signal conditioning, buffering, sensing, or feedback-control functions without adding a second package. The LM2904QD is identified as an automotive temperature-grade variant. Its 26 V supply capability accommodates automotive-style power rails, while the 700 kHz gain-bandwidth product supports general-purpose closed-loop signal amplification at moderate frequencies. The dual architecture also reduces component count in systems that need two equivalent amplifier channels. Operation from a single positive supply is a defining family characteristic, although common-mode range, output swing, offset, and noise figures should be checked against the manufacturer datasheet for the exact operating conditions. The 8-terminal SOP package uses gull-wing leads and a rectangular body, making LM2904QD suitable for conventional through-hole board assembly rather than a compact surface-mount land pattern. Because the automotive suffix denotes a qualified ordering configuration, engineers should confirm the exact qualification, temperature range, marking, and production-test requirements in the Texas Instruments ordering information before release to manufacturing. Typical applications include automotive sensor interfaces, actuator-driver feedback paths, battery-monitoring circuits, instrumentation signal conditioning, and low-frequency control loops. In each case, the two amplifier sections can process complementary or independent signals. The 700 kHz bandwidth is generally more relevant to low-bandwidth sensing and feedback than to high-speed signal processing, so applications requiring wide-band precision or rail-to-rail output should be reviewed separately. The principal design consideration is error budget: input offset voltage, input bias current, common-mode input range, output voltage swing, supply current, and stability with the selected feedback network determine practical accuracy. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased according to the manufacturer’s recommended configuration. PCB layout should preserve a low-impedance ground return and avoid long feedback traces. This page combines the Texas Instruments family specifications, package details, drop-in alternatives, and implementation guidance into an engineering-focused reference. It also identifies which parameters require confirmation in the full manufacturer datasheet, helping designers distinguish confirmed LM2904QD characteristics from application-specific design requirements.

RFQ پەیوەندی
LM2904QDR - Dual 26V 700kHz Operational Amplifier | Texas Instruments
LM2904QDR

LM2904QDR - Dual 26V 700kHz Operational Amplifier | Texas Instruments

Texas Instruments LM2904QDR is a dual, general-purpose operational amplifier with two amplifier circuits, a 26 V power-supply rating, and a 700 kHz gain-bandwidth product. The device is offered in an 8-pin SOIC package and is specified for operation from -40 °C to +125 °C. It is intended for instrumentation, buffering, general signal conditioning, and applications requiring two amplifiers in one package. An operational amplifier is an active analog signal-processing component that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog and mixed-signal integrated circuits, the dual operational amplifier combines two amplifier channels with a shared power supply. The LM2904 family is commonly used where economical, general-purpose amplification is needed rather than high-speed, low-noise, or precision performance. The LM2904QDR provides two independent amplifier circuits in one 8-pin SOIC package. Its stated 700 kHz gain-bandwidth product supports general-purpose feedback-based signal amplification, while the 26 V maximum supply rating accommodates conventional industrial and automotive-style supply environments. The dual configuration reduces package count when two amplifier channels are required in the same circuit board area. The operating-temperature range of -40 °C to +125 °C makes the device suitable for temperature-extended industrial equipment, instrumentation, control systems, and vehicle electronics when the surrounding system also meets the required operating limits. The SOIC (D) package also supports conventional surface-mount assembly. Designers should use the manufacturer pin-description table when assigning PCB nets and must account for input common-mode range, output swing, input bias current, noise, and stability requirements in the final signal chain. Typical uses include sensor-signal conditioning, low-frequency transducer amplification, audio preamplification, voltage buffering, loop filtering, and general industrial control interfaces. In a dual instrumentation circuit, one channel can amplify a sensor output while the other provides buffering, gain, or active filtering. Because the amplifier is intended for general-purpose use, its performance should be checked against the accuracy, bandwidth, noise, and common-mode requirements of the application rather than inferred from the maximum supply rating alone. For PCB design, keep the feedback network and input nodes compact, provide normal supply bypassing, and avoid long traces that increase parasitic capacitance or pickup. Check whether the selected gain and capacitive loading require additional compensation. Use the manufacturer datasheet for the complete electrical characteristics, recommended operating conditions, pin functions, and application guidance. This page combines the verified device identity, package information, operating-temperature data, source links, drop-in comparison options, and practical design guidance to support faster component selection and PCB implementation.

RFQ پەیوەندی
LM2904QDRG4 - Dual 26 V 700 kHz Op Amp | Texas Instruments
LM2904QDRG4

LM2904QDRG4 - Dual 26 V 700 kHz Op Amp | Texas Instruments

Texas Instruments LM2904QDRG4 is a dual general-purpose operational amplifier designed for industrial and automotive control systems. The device contains two independent, internally frequency-compensated amplifiers, operates from a single supply as high as 26 V, and supports dual supplies of ±13 V. Each channel has a gain-bandwidth product of 700 kHz and a slew rate of 0.3 V/µs, while the typical supply-current drain is 0.7 mA. The specified package is the narrow-body 8-SOIC, supplied tape and reel. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify voltage differences. The dual-amplifier configuration places two independent amplifiers in one package, making it useful within the hierarchy of op amp, dual op amp, analog IC, and integrated circuit. Common uses include sensor conditioning, voltage amplification, comparison, and control-loop stages where broad supply-voltage tolerance is valuable. The LM2904QDRG4 is specified for single-supply operation up to 26 V and dual-supply operation at ±13 V. Its common-mode input range includes ground, which allows the device to process signals near the lower supply rail. The internally frequency-compensated architecture simplifies closed-loop design, while the 700 kHz gain-bandwidth product supports general-purpose signal paths rather than high-speed precision applications. The two channels provide independent operation, allowing one channel to perform signal amplification while the other handles feedback, comparison, or monitoring. A 0.3 V/µs slew rate governs large-signal response, and the 0.7 mA typical supply-current drain supports low-power control designs. The 8-SOIC footprint is widely used for industrial and automotive printed-circuit boards, although engineers should verify the exact pin arrangement and exposed thermal requirements in the manufacturer datasheet. Typical applications include automotive sensor interfaces, industrial control loops, low-level signal conditioning, actuator-driver feedback networks, and general dual-amplifier signal paths. The 26 V supply capability is particularly useful when a circuit must operate from a nominal 24 V industrial rail while retaining tolerance for transient excursions, provided the absolute maximum limits are respected. When designing a replacement, verify the channel pinout, supply limits, common-mode range, output-swing limits, and required package dimensions before changing the PCB. Decoupling capacitors should be placed close to the supply pins, and sensitive layouts should minimize parasitic capacitance between input and output nodes to preserve stability. This page combines manufacturer specifications, package information, same-family replacement guidance, comparison parameters, and practical circuit-design considerations. It is intended to help engineers identify an exact-footprint alternative, compare practical constraints, and design the LM2904QDRG4 into industrial or automotive control electronics.

RFQ پەیوەندی
LM2904QDRG4Q1 - Dual 26 V AEC-Q100 Op Amp, 700 kHz, SOIC-8 | Texas Instruments
LM2904QDRG4Q1

LM2904QDRG4Q1 - Dual 26 V AEC-Q100 Op Amp, 700 kHz, SOIC-8 | Texas Instruments

The Texas Instruments LM2904QDRG4Q1 is an automotive-grade dual operational amplifier with two independent, internally compensated amplifiers packaged in an 8-pin SOIC (DBV) package. Each channel delivers a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operates from a single supply between 3 V and 26 V. What is a dual operational amplifier? A dual op amp is a single integrated circuit containing two independent, high-gain, frequency-compensated amplifiers. It belongs to the hierarchy: operational amplifier -> analog amplifier IC -> integrated circuit -> semiconductor. The LM2904-Q1 family is the AEC-Q100-qualified automotive version of the industry-standard LM2904, which is one of the most widely cloned and second-sourced general-purpose amplifier footprints in the world. Key electrical features include a low supply-current drain that is independent of supply voltage (0.7 mA typical per amplifier), a common-mode input voltage range that includes ground, and a common-mode rejection ratio of 65 dB. Because the amplifiers are internally compensated, no external frequency-compensation network is required, which simplifies both PCB layout and BOM cost in automotive designs. Internally, each amplifier uses a differential input stage with a class-A output stage that provides good output swing and load-driving capability. The single-supply operation from 3 V to 26 V directly accommodates 12 V battery-derived automotive rails with transient margin, and allows the same part to be used across 5 V, 12 V and 24 V nominal systems without a second part number. Typical automotive applications include body electronics modules, actuator and relay drivers, sensor signal conditioning for resistive sensors, battery monitoring, and low-cost power supply feedback. The same amplifier is equally suited to industrial instrumentation, audio preamplifier stages, and general DC signal conditioning where a cost-optimized general-purpose dual amplifier is preferred over a precision rail-to-rail part. When designing with the LM2904QDRG4Q1, remember that it is a bipolar general-purpose amplifier with input common-mode range that does not reach the positive rail. Place a supply-bypass capacitor of 0.1 uF close to pin 8 and a bulk capacitor near pin 4, and use resistors of 10 kohm or lower in the feedback network to preserve bandwidth. This page consolidates manufacturer specifications, AEC-Q100 qualification details, drop-in SOIC-8 alternatives from Texas Instruments and STMicroelectronics, and practical layout guidance that is not collected in one place on a distributor listing.

RFQ پەیوەندی
LM2904QDRQ1 - Dual 26V 700kHz Op Amp AEC-Q100 | TI
LM2904QDRQ1

LM2904QDRQ1 - Dual 26V 700kHz Op Amp AEC-Q100 | TI

The Texas Instruments LM2904QDRQ1 is an automotive-grade, dual operational amplifier qualified to AEC-Q100, operating from a single supply of 3V to 26V (or dual supplies plus/minus 1.5V to plus/minus 13V) with a 700 kHz gain-bandwidth product in an 8-pin SOIC (D) package rated -40C to +125C. An operational amplifier (op amp) is a high-gain differential-input voltage amplifier and a fundamental analog building block within the signal-chain hierarchy: op amp -> amplifier IC -> analog/mixed-signal IC -> semiconductor. A dual op amp integrates two independent amplifiers in one package, cutting board space and BOM cost for multi-channel signal conditioning. Key features include a low 500 uA supply current per amplifier, a common-mode input range that includes ground (enabling true single-supply operation), internal frequency compensation, and output short-circuit protection. ESD protection exceeds 500 V per MIL-STD-883 Method 3015 and 200 V on the machine model, per the TI datasheet. Technically, the bipolar process yields a typical 2 mV input offset voltage (7 mV max) and 20 nA typical input bias current. The 0.3 V/us slew rate and 700 kHz GBW suit low-frequency sensor and control loops; the output swings close to the negative rail but is not rail-to-rail. Operation remains stable with moderate capacitive loads. Typical applications include automotive sensor signal conditioning (temperature, pressure, position), current sensing, active filters, DC motor control, and battery management front-ends, where the 26V rating allows direct operation from a 12V automotive battery rail with load-dump headroom. Design tip: decouple VCC with a 0.1 uF ceramic close to pin 8, keep the input common-mode below VCC-1.5V, and buffer high-impedance sources to limit offset errors. For new automotive designs requiring 36V ratings and tighter offset, consider the next-generation LM2904B-Q1 family.

USD $0.22 پەیوەندی
LM2904QM8-13 - 36 V Dual Op Amp | Diodes Incorporated
LM2904QM8-13

LM2904QM8-13 - 36 V Dual Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904QM8-13 is an automotive-compliant, dual general-purpose operational amplifier with a 36 V total supply rating and an 8-pin MSOP package. It combines two amplifier channels, 500 uA supply current, 20 nA input offset current, and 100 dB open-loop gain into an industry-standard surface-mount format. The LM2904QM8-13 is designed for signal conditioning, analog measurement, and control circuits operating from dual or single-ended supplies. An operational amplifier is a high-gain analog building block that compares an input voltage with a feedback voltage and drives its output to reduce the difference between them. In the signal-conditioning hierarchy, the LM2904QM8-13 belongs to the general-purpose operational-amplifier class, a type of analog amplifier used in instrumentation, sensor interfaces, active filters, and closed-loop control. Its dual-channel configuration allows two amplifier functions in one package while reducing board area. The main features of this device include two amplifier circuits, a 36 V maximum total supply voltage, 500 uA supply current, 20 nA input offset current, and 100 dB open-loop gain. The automotive-compliant construction identifies it for applications requiring a higher-reliability general-purpose amplifier. Its MSOP-8 package supports compact PCB layouts, while the -13 ordering suffix identifies tape-and-reel production packaging. The manufacturer describes the LM2904Q family as automotive-compliant dual and quad operational amplifiers, with industry-standard pinouts and green mold compound. The LM2904Q and LM2904AQ devices are offered in SO-8, TSSOP-8, and MSOP-8 packages. This package compatibility gives engineers a familiar circuit implementation, while the dual topology simplifies circuits requiring one signal-conditioning channel and one feedback or drive channel. Typical uses include low-side current sensing, transducer amplification, active filtering, comparator-style signal conditioning, and general industrial control. In current-sensing applications, the amplifier compares a scaled voltage across a shunt with a reference. In sensor interfaces, it amplifies small voltage changes around a common-mode level. In active filters, its gain-bandwidth behavior and open-loop gain define the operating point when combined with external resistors and capacitors. For a new layout, verify the MSOP-8 pin assignment and orient the exposed package according to the manufacturer datasheet before assigning input, output, supply, and feedback connections. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept away from switching nodes and high-current paths. The 36 V rating is a maximum operating limit rather than a recommended supply condition. This page organizes the verified device characteristics, package information, application guidance, and same-family replacement candidates into a practical engineering reference. It also highlights where a new design should consult the manufacturer datasheet for detailed electrical limits, test conditions, pin definitions, and qualification criteria.

RFQ پەیوەندی
LM2904QP - Dual 26V 700kHz Op-Amp TSSOP-8 | Texas Instruments
LM2904QP

LM2904QP - Dual 26V 700kHz Op-Amp TSSOP-8 | Texas Instruments

The Texas Instruments LM2904QP is a dual general-purpose operational amplifier rated for 26 V supply operation with a 700 kHz gain-bandwidth product, housed in an 8-pin TSSOP (PW) package. As a Q-suffix automotive-grade variant, it is AEC-Q100 qualified and specified from -40C to +125C, making it suited to vehicle and harsh-environment electronics. A dual operational amplifier is an integrated circuit that packs two independent, internally frequency-compensated op amps onto a single silicon die within one package. Op amps are the foundational building blocks of the analog signal chain, sitting within the broader hierarchy of amplifier ICs, linear ICs, and semiconductors, and they perform amplification, buffering, filtering, comparison, and level shifting in virtually every electronic system. Key features of the LM2904QP include operation from a single supply or dual supplies, a low supply-current drain of approximately 0.7 mA typ that is largely independent of supply voltage, and a common-mode input voltage range that includes ground, allowing direct sensing of signals near 0 V in single-supply systems. The two channels are closely matched, reducing board space versus discrete single-channel amplifiers. Technically, the LM2904 family uses internally compensated bipolar technology, which guarantees unity-gain stability without external compensation components. The ground-inclusive input common-mode range and single-supply capability eliminate the need for a negative rail in low-side sensing applications, while the 700 kHz bandwidth covers audio, low-speed control loops, and general industrial signal conditioning. Low input bias and offset currents minimize error in high-impedance source applications. Typical applications include automotive sensor signal conditioning, low-side current sensing, active filters, transducer amplifiers, and battery-powered industrial instrumentation, where single-supply operation near ground and wide temperature tolerance are essential. Design consideration: the output cannot swing rail-to-rail, so allow headroom on both rails and verify the output swing specification in the manufacturer datasheet against your signal range, especially at elevated temperature and light load. This page synthesizes the manufacturer product data, drop-in alternatives, comparison tables, and practical design notes in one place, providing engineering context beyond a raw parametric listing.

RFQ پەیوەندی
LM2904QPWRG4Q1 - 26V Dual Op Amp | Texas Instruments
LM2904QPWRG4Q1

LM2904QPWRG4Q1 - 26V Dual Op Amp | Texas Instruments

Texas Instruments LM2904QPWRG4Q1 is an automotive-grade, dual general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, and a 700 kHz gain-bandwidth product. The device is packaged in an 8-pin TSSOP (PW) package and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is a high-gain, frequency-compensated analog building block used to amplify sensor signals, control feedback loops, buffer voltage references, and perform general signal conditioning. The LM2904 belongs to the dual operational-amplifier hierarchy and combines low supply-current consumption with a wide common-mode input range that includes ground, making it suitable for single-supply systems operating near the lower rail. The dual configuration provides two amplifiers in one package, reducing board area when a design needs matched general-purpose stages. Key characteristics include a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, and a typical low supply-current drain of 0.7 mA per amplifier. Its AEC-Q100 qualification supports automotive-grade applications where temperature robustness and production quality requirements are important. Internally, the device contains two independent, high-gain, frequency-compensated amplifiers. Frequency compensation allows operation without external compensation, while the ground-referenced common-mode capability is valuable for sensing small signals produced by sensors, resistive dividers, and single-supply analog circuits. The 26 V maximum rating also provides headroom for industrial and automotive supply environments. Typical uses include low-side current sensing, sensor-signal conditioning, actuator feedback, automotive interface electronics, and general dual-amplifier signal conditioning. Because both channels are independent, one package can support two related functions, such as signal amplification and an active filter, without requiring separate single amplifier packages. Designers should maintain input and output voltage limits, account for input common-mode range, and provide stable feedback-network layouts around the device. Decoupling capacitors should be placed close to the supply pins, while sensitive input and feedback nodes should be kept away from switching-current paths. The automotive qualification does not replace application-level validation of transient immunity, noise, and thermal performance. This page organizes the device specifications, qualified family information, package details, practical design guidance, and qualified same-footprint alternatives into an engineering-focused selection resource for analog and automotive power-management designs.

RFQ پەیوەندی
LM2904QPWRQ1 - Dual 26V 700kHz AEC-Q100 Op Amp | Texas Instruments
LM2904QPWRQ1

LM2904QPWRQ1 - Dual 26V 700kHz AEC-Q100 Op Amp | Texas Instruments

Texas Instruments LM2904QPWRQ1 is an AEC-Q100-qualified, dual operational amplifier with a 26 V power-supply rating and 700 kHz gain-bandwidth product. The device contains two general-purpose amplifiers in an 8-pin TSSOP package, making it suitable for automotive signal-conditioning, instrumentation, sensor-interface, and industrial control circuits. Its dual-channel architecture also allows one package to provide gain, filtering, buffering, or differential amplification in two related signal paths. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is shaped by external feedback components. Op amps belong to the broader amplifier IC and analog-signal-processing hierarchy. They are widely used because a feedback network can set closed-loop gain, improve impedance characteristics, and enable stable implementations of common analog functions using resistors and capacitors. The LM2904-Q1 family provides the established LM2904 operating characteristics in an automotive-qualified configuration. Key headline features include two amplifier channels, operation from a 26 V-rated supply, a 700 kHz gain-bandwidth product, and AEC-Q100 qualification. The manufacturer identifies the device as an industry-standard dual operational amplifier for automotive applications, where qualification supports controlled introduction into automotive electronic systems. Its 700 kHz bandwidth makes the amplifier suitable for moderate-speed precision signal paths rather than high-frequency RF or video amplification. The dual architecture reduces package count when two independent gain or filtering stages are required. This is particularly useful in sensor interfaces, actuator drivers, battery-monitoring circuits, and automotive control modules where board area and component count affect reliability. Typical applications include automotive sensor conditioning, low-side current measurement, transducer amplification, voltage buffering, and general-purpose analog signal processing. The high supply-voltage capability can simplify interfaces to automotive battery-derived rails, although designers must still observe the datasheet limits for input common-mode range, output swing, supply current, and thermal conditions. A primary design consideration is that the TSSOP package has limited thermal dissipation capability. Follow the manufacturer datasheet for input and output voltage limits, common-mode behavior, electrical characteristics, and application guidance. Place bypassing capacitors close to the supply pins, preserve the recommended feedback topology, and verify common-mode and output-swing limits across the complete operating range. This product page combines the manufacturer specification summary, automotive qualification information, package details, verified source links, application guidance, and a compatibility-oriented comparison framework. That engineering context helps distinguish the LM2904QPWRQ1 from lower-voltage modern op amps, higher-bandwidth alternatives, and non-automotive versions before a PCB or BOM decision is made.

RFQ پەیوەندی
LM2904QS-13 - 36V Dual Op Amp, 1.1MHz | Diodes Incorporated
LM2904QS-13

LM2904QS-13 - 36V Dual Op Amp, 1.1MHz | Diodes Incorporated

Diodes Incorporated LM2904QS-13 is an automotive-compliant dual operational amplifier packaged in an 8-pin SO-8 package. The device operates from a 36 V maximum supply, provides two amplifier channels, and combines a 1.1 MHz gain-bandwidth product with 100 dB open-loop gain. Its 500 uA quiescent current and 20 nA typical input bias current suit low-power analog signal chains that require higher voltage tolerance than conventional low-voltage amplifier families. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is defined primarily by external feedback components. Within the semiconductor hierarchy, the LM2904QS-13 belongs to the operational amplifier, analog amplifier IC, and power-management-supporting signal-conditioning categories. It can amplify sensor outputs, implement active filters, buffer voltage references, and perform general-purpose analog conditioning where a wide supply range and dual-channel integration are useful. Key characteristics include two independent amplifier circuits, a 36 V maximum supply, 1.1 MHz unity-gain bandwidth, 100 dB open-loop gain, 500 uA quiescent current, and a typical input bias current of 20 nA. These characteristics make the part appropriate for industrial control, instrumentation, automotive electronics, and appliance applications where two channels can reduce component count and board space. The automotive-compliant LM2904Q family is also manufactured with green mold compound as standard. The LM2904 architecture supports single-supply operation as well as conventional dual-supply operation when negative supply voltage is available. Input and output common-mode limits must remain within the operating boundaries stated in the manufacturer datasheet. Because the amplifier is intended for broad-voltage applications, designers should distinguish the 36 V maximum supply rating from the usable output-swing and input-common-mode ranges; those ranges are not determined by the maximum supply alone. Typical applications include sensor conditioning, current-loop receivers, active low-pass filters, audio and communications blocks, automotive electronics, industrial control modules, and general analog signal-conditioning boards. Two integrated channels are especially useful when a design requires closely related positive and negative signals, such as differential sensor outputs, dual-axis sensing, or paired audio paths. Local decoupling and careful trace routing remain important because high-gain amplifiers can amplify noise, oscillation, and unintended feedback caused by poor layout. For stable operation, place the power-supply bypass capacitor close to the supply pins, keep feedback components compact, and route output signals away from high-impedance input nodes. Avoid placing long copper traces beneath the amplifier unless the layout specifically supports the intended thermal and electrical behavior. Check the complete pin assignment and exposed-package details against the manufacturer datasheet before finalizing a footprint or assembling a prototype. This product page combines the LM2904QS-13 package and electrical identity, verified manufacturer documentation, same-footprint replacement guidance, application-specific engineering notes, and a parameter comparison intended to accelerate component selection. The primary decision factors are SO-8 footprint compatibility, supply voltage, unity-gain bandwidth, input bias current, quiescent current, and automotive qualification requirements.

RFQ پەیوەندی
LM2904QTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated
LM2904QTH-13

LM2904QTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated

Diodes Incorporated LM2904QTH-13 is a dual general-purpose operational amplifier designed for automotive electronics. It contains two independent high-gain amplifiers in an 8-pin TSSOP package, operates from a single supply up to 36 V or from dual supplies up to ±18 V, and is identified as AEC-Q100 compliant. Key characteristics include a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, 7 mV input-offset voltage, 250 nA input-bias current, and approximately 700 µA supply current. An operational amplifier is a high-gain analog signal-conditioning IC that compares an input voltage with a feedback reference and drives its output to reduce the difference between them. The LM2904 dual-amplifier configuration belongs to the operational-amplifier family within analog ICs and analog signal-processing semiconductors. Its two channels may be used independently for signal conditioning, voltage comparison, feedback control, or other general-purpose analog functions. The LM2904QTH-13 combines relatively wide supply-voltage tolerance with low quiescent current and automotive-compliant construction. A 36 V maximum supply makes it useful in systems operating from industrial or automotive batteries after appropriate transient and protection design. Its 700 kHz gain-bandwidth product is adequate for low-to-moderate-frequency signal paths, while the 0.3 V/µs slew rate affects how quickly the output can follow large voltage changes. The 40 mA output-current figure and 250 nA input-bias current define important loading and input-stage constraints. The two amplifiers provide flexibility within one compact package, reducing component count in dual-channel circuits. Each channel has its own differential input and output pins, allowing simultaneous or independent operation. Because the device is intended for general-purpose amplification, its offset voltage, input-bias current, bandwidth, and output-drive capabilities must be checked against the target signal amplitude, source impedance, load, noise requirements, and stability conditions. Typical applications include automotive sensor conditioning, actuator and valve-driver feedback, battery-powered instrumentation, industrial control modules, current monitoring, and low-frequency signal amplification. In battery-powered systems, the approximately 700 µA supply-current characteristic helps limit standing power when both channels are operating at low utilization. For high-impedance sensors, the 250 nA input-bias current should be compared with the sensor's effective source impedance and resulting offset error. The main design consideration is maintaining stability with the output load and compensation network selected for the target feedback topology. Keep sensitive input traces away from power paths and output nodes, provide local supply bypassing, and account for automotive supply transients at the board interface. The TSSOP-8 outline also requires thermal analysis when both channels drive demanding loads at elevated ambient temperature. This product page combines the manufacturer and distributor characteristics for the LM2904QTH-13 with package, replacement, application, and design guidance. It highlights practical distinctions among same-footprint alternatives and identifies the electrical details that require confirmation against the current manufacturer datasheet before production release.

RFQ پەیوەندی