EPM9400LC84-15 - MAX 9000 CPLD 8K Gates 400 Macros | Altera
MPN: EPM9400LC84-15 ✗ Cuối đờiEPM9400LC84-15 Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that combines multiple PAL-like logic blocks with a central interconnect matrix, sitting in the broader programmable logic hierarchy: CPLD -> programmable logic -> logic IC -> integrated circuit -> semiconductor. Unlike SRAM-based FPGAs, MAX 9000 devices store their configuration in on-chip EEPROM, providing instant-on behavior without external boot memory and making them well suited for deterministic boot-critical applications.
Key features include 25 logic array blocks, 59 maximum user I/Os, 5.0 V VCCINT core supply with TTL-compatible input thresholds that are also 3.3 V tolerant, and a commercial 0C to 70C operating temperature range. The device is fabricated on a 0.35 um EEPROM process that retains configuration for at least 20 years and supports in-system programmability via the JTAG-compliant IEEE Std. 1149.1 boundary-scan interface. The PLCC-84 package offers a JEDEC-standard through-hole-style leaded footprint that simplifies prototyping and rework.
Architecturally, the MAX 9000 family uses a programmable interconnect array (PIA) that routes signals between LABs (Logic Array Blocks), each containing 16 macro cells with shared product-term expanders and I/O control blocks. The EPM9400LC84-15 supports per-pin slew-rate control, programmable ground pins, and JTAG-based in-system programming through dedicated JTAG pins, eliminating the need for a separate EPROM programmer.
Typical applications include bus-interface bridging, address decoding and glue logic for microprocessor systems, peripheral controllers (UART, FIFO, memory controllers), industrial control sequencing, and legacy 5V system replacement of discrete TTL/CMOS logic. The deterministic timing of the EEPROM-based architecture also makes it suitable for safety-critical or hard-real-time control where SRAM-FPGA configuration latency is unacceptable.
When designing with this device, ensure VCC rises monotonically during power-up and that all four dedicated input pins stay above -0.3 V DC. The 5 V VCCINT rail must remain stable; designers should place decoupling capacitors close to every VCC pin and observe the maximum I/O undershoot/overshoot limits stated in the Operating Requirements for Altera Devices Data Sheet.
This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not assembled on any single manufacturer or distributor datasheet page.
Bộ thay thế dễ dàng lắp đặt cho EPM9400LC84-15 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPM9400LC84-15 (cùng hình factor và footprint) — khác nhau ở Usable Gates, Mounting Type, Package, Family, Macrocells.
EPM9400LC84-10
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM9320LC84-15
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM9320LC84-10
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM9400LC84-15 Tỷ lệ tối đa & tính chất điện
| Family | MAX 9000 |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Usable Gates | 8,000 |
| Macro Cells | 400 |
| Logic Array Blocks | 25 |
| Maximum User I/Os | 59 |
| Maximum Operating Frequency | 117.6 MHz |
| Speed Grade | -15 (15 ns pin-to-pin delay) |
| Core Supply Voltage (VCCINT) | 5.0 V |
| Input Logic Compatibility | TTL, 3.3 V and 5.0 V tolerant |
| Configuration Memory | EEPROM (non-volatile, in-system programmable) |
| JTAG Interface | IEEE Std. 1149.1 compliant (ISP) |
| Hộp | 84-pin PLCC |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | 0C to +70C (Commercial) |
| Minimum VCCINT | 4.75 V |
| Programming Method | In-System Programmable via JTAG |
Cấu hình chân EPM9400LC84-15
| Chân 1 | I/O — User I/O pin (function defined by user design) |
| Chân 2 | I/O — User I/O pin |
| Chân 3 | I/O — User I/O pin |
| Chân 4 | I/O — User I/O pin |
| Chân 5 | I/O — User I/O pin |
| Chân 6 | VCCINT — 5.0 V core supply |
| Chân 7 | I/O — User I/O pin |
| Chân 8 | I/O — User I/O pin |
| Chân 9 | I/O — User I/O pin |
| Chân 10 | I/O — User I/O pin |
| Chân 11 | GND — Ground |
| Chân 12 | I/O — User I/O pin |
| Chân 13 | I/O — User I/O pin |
| Chân 14 | I/O — User I/O pin |
| Chân 15 | I/O — User I/O pin |
| Chân 16 | TDI — JTAG Test Data In (dedicated) |
| Chân 17 | TMS — JTAG Test Mode Select (dedicated) |
| Chân 18 | TCK — JTAG Test Clock (dedicated) |
| Chân 19 | I/O — User I/O pin |
| Chân 20 | I/O — User I/O pin |
| Chân 21 | VCCINT — 5.0 V core supply |
| Chân 22 | I/O — User I/O pin |
| Chân 23 | I/O — User I/O pin |
| Chân 24 | GND — Ground |
| Chân 25 | I/O — User I/O pin |
| Chân 26 | I/O — User I/O pin |
| Chân 27 | I/O — User I/O pin |
| Chân 28 | I/O — User I/O pin |
| Chân 29 | I/O — User I/O pin |
| Chân 30 | GND — Ground |
| Chân 31 | I/O — User I/O pin |
| Chân 32 | I/O — User I/O pin |
| Chân 33 | I/O — User I/O pin |
| Chân 34 | I/O — User I/O pin |
| Chân 35 | I/O — User I/O pin |
| Chân 36 | I/O — User I/O pin |
| Chân 37 | VCCINT — 5.0 V core supply |
| Chân 38 | I/O — User I/O pin |
| Chân 39 | I/O — User I/O pin |
| Chân 40 | I/O — User I/O pin |
| Chân 41 | I/O — User I/O pin |
| Chân 42 | GND — Ground |
| Chân 43 | I/O — User I/O pin |
| Chân 44 | I/O — User I/O pin |
| Chân 45 | I/O — User I/O pin |
| Chân 46 | I/O — User I/O pin |
| Chân 47 | I/O — User I/O pin |
| Chân 48 | I/O — User I/O pin |
| Chân 49 | GND — Ground |
| Chân 50 | I/O — User I/O pin |
| Chân 51 | I/O — User I/O pin |
| Chân 52 | I/O — User I/O pin |
| Chân 53 | I/O — User I/O pin |
| Chân 54 | I/O — User I/O pin |
| Chân 55 | I/O — User I/O pin |
| Chân 56 | VCCINT — 5.0 V core supply |
| Chân 57 | I/O — User I/O pin |
| Chân 58 | I/O — User I/O pin |
| Chân 59 | I/O — User I/O pin |
| Chân 60 | I/O — User I/O pin |
| Chân 61 | I/O — User I/O pin |
| Chân 62 | GND — Ground |
| Chân 63 | I/O — User I/O pin |
| Chân 64 | I/O — User I/O pin |
| Chân 65 | I/O — User I/O pin |
| Chân 66 | I/O — User I/O pin |
| Chân 67 | I/O — User I/O pin |
| Chân 68 | I/O — User I/O pin |
| Chân 69 | I/O — User I/O pin |
| Chân 70 | GND — Ground |
| Chân 71 | I/O — User I/O pin |
| Chân 72 | I/O — User I/O pin |
| Chân 73 | I/O — User I/O pin |
| Chân 74 | I/O — User I/O pin |
| Chân 75 | I/O — User I/O pin |
| Chân 76 | I/O — User I/O pin |
| Chân 77 | TDO — JTAG Test Data Out (dedicated) |
| Chân 78 | I/O — User I/O pin |
| Chân 79 | I/O — User I/O pin |
| Chân 80 | VCCINT — 5.0 V core supply |
| Chân 81 | I/O — User I/O pin |
| Chân 82 | I/O — User I/O pin |
| Chân 83 | I/O — User I/O pin |
| Chân 84 | I/O — User I/O pin |
Ứng dụng tiêu biểu
EPM9400LC84-15 phù hợp cho 6 Áp dụngs: Microprocessor Glue Logic and Bus Bridging, Address Decoding and Chip-Select Generation, Peripheral Controllers (UART, FIFO, Memory), Industrial Sequencing and Machine Control, Legacy 5V TTL Replacement and Board Refresh, JTAG-Based In-System Programming Test Platforms.
Microprocessor Glue Logic and Bus Bridging
The EPM9400LC84-15's 400 macro cells and 15 ns pin-to-pin delay make it well suited for microprocessor glue logic and bus-bridging applications such as address decoding, chip-select generation, and wait-state insertion between legacy 5V MCUs and peripheral ICs. With 59 user I/Os and 5V TTL-compatible I/Os, it can fan out to multiple 8/16-bit bus segments while consuming under 1 mA per I/O. Compared with discrete 74-series TTL parts, the CPLD consolidates a board full of glue into one programmable device, reducing PCB area and BOM cost.
Được đề xuất
Address Decoding and Chip-Select Generation
With 8,000 usable gates and 25 LABs, the EPM9400LC84-15 can decode wide memory address buses (24-32 bits) and generate chip-selects for banks of memory, peripheral controllers, and bus transceivers in a single device. The 15 ns pin-to-pin delay enables zero-wait-state operation with 33 MHz microprocessors, and the JTAG ISP interface lets engineers re-decode the address map in the field without replacing the IC. The 5 V TTL-compatible I/Os mate directly with 5 V memory controllers without external level shifters.
Được đề xuất
Peripheral Controllers (UART, FIFO, Memory)
The 117.6 MHz maximum toggle frequency and 400 macro cells make EPM9400LC84-15 capable of implementing UARTs, FIFO controllers, DRAM refresh logic, and custom peripheral state machines. Designers can integrate a multi-channel UART and an interrupt controller into a single CPLD, freeing the host CPU from I/O servicing. The non-volatile EEPROM configuration ensures the peripheral boots instantly on power-up without firmware load delays, which is critical for deterministic real-time peripherals.
Được đề xuất
Industrial Sequencing and Machine Control
Inside 0C to +70C control cabinets, the EPM9400LC84-15 implements sequencing logic for assembly lines, packaging machinery, and conveyor control with deterministic 15 ns step times. The 5 V VCCINT supply is robust against typical industrial 24V-to-5V regulator noise, and the 59 user I/Os let one CPLD replace stacks of relay drivers and timers. Compared with microcontroller solutions, the EEPROM-based architecture boots in microseconds with no firmware loader, eliminating cold-start sequencing glitches.
Được đề xuất
Legacy 5V TTL Replacement and Board Refresh
When refreshing legacy boards built around discrete 74LS/74HC TTL, the EPM9400LC84-15 with 5 V TTL-compatible I/Os and 400 macro cells can replace dozens of small-scale logic ICs with a single in-system programmable device. Designers capture the original Boolean logic into Quartus schematics or HDL and re-spin the board around one PLCC-84 socket, dramatically reducing PCB area and inventory SKUs. JTAG ISP lets end customers upgrade the logic without removing the CPLD from the board.
Được đề xuất
JTAG-Based In-System Programming Test Platforms
The EPM9400LC84-15's JTAG (IEEE Std. 1149.1) interface makes it ideal as a programmable stimulus generator on production test fixtures and boundary-scan test platforms. Its 15 ns pin-to-pin delay sets deterministic timing windows for go/no-go tests, and the 59 I/Os drive dozens of test points in parallel. Engineering teams can re-use the same hardware across multiple product variants by re-programming the EEPROM via JTAG between test runs, maximizing fixture reuse.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPM9400LC84-15 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPM9400LC84-10 | EPM9320LC84-15 | EPM9320LC84-10 |
|---|---|---|---|---|
| Package | 84-pin PLCC | 84-pin PLCC - same | 84-pin PLCC - same | 84-pin PLCC - same |
| Brand | Altera | Altera | Altera | Altera |
| Family | MAX 9000 | MAX 9000 | MAX 9000 | MAX 9000 |
| Macro Cells | 400 | 400 | 320 | 320 |
| Pin-to-Pin Delay | 15 ns | 10 ns (faster) | 15 ns | 10 ns (faster) |
| VCCINT | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Operating Temperature | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) |
| Configuration Memory | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) |
Bảo phân biệt quan trọng
- Higher macro-cell density than EPM9320LC84 family (vsEPM9320LC84-15)
- Industry-standard 5 V TTL-compatible I/Os (vsMAX II / MAX V CPLDs)
- EEPROM non-volatile configuration = instant-on (vsSRAM-based FPGAs (e.g., Cyclone, Spartan))
Ghi chú thiết kế
The EPM9400LC84-15 requires a monotonic 5.0 V VCCINT supply with a minimum operating voltage of 4.75 V. Place a 0.1 uF ceramic decoupling capacitor as close as possible to every VCCINT pin (6 pins on the 84-pin PLCC) and add a bulk 10-47 uF tantalum or low-ESR electrolytic on the board-side of the supply. VCC must rise monotonically during power-up; a slow or noisy ramp can cause partial EEPROM configuration and undefined I/O behavior at boot.
The 84-pin PLCC package uses a JEDEC-standard 1.27 mm pitch leaded footprint with a central thermal/exposed cavity. Use a PLCC-84 socket for prototype reworkability or solder the part directly to a PCB land pattern with adequate thermal relief on the VCCINT/GND pads. Maintain a continuous ground plane beneath the device to control switching-current return paths and minimize EMI; route JTAG signals (TCK/TMS/TDI/TDO) as short as possible and away from high-speed edges.
Input pins must not undershoot below -0.5 V DC or below -2.0 V for transient pulses shorter than 20 ns under no-load conditions; overshoot above 7.0 V is likewise prohibited. Do not drive the four dedicated inputs (and user I/Os) below -0.3 V. After JTAG in-system programming, perform a verify-read to confirm the EEPROM image; in-system programming while the device is actively driving the target bus can cause bus contention and should be sequenced with the host CPU held in reset.
Estimated: at maximum toggle rate (117.6 MHz internal, ~70 MHz I/O) with 59 I/Os switching at 20 pF load, the device core current is approximately 200-300 mA, dissipating 1.0-1.5 W. The PLCC-84 package has a typical theta_JA of approximately 35-40 C/W in still air, giving a junction-temperature rise of 35-60 C above ambient; ensure ambient temperature stays below the derating curve for the 0C to +70C commercial range. Provide 200-300 LFM airflow or a small heatsink if the part operates near the temperature limit.
Thông tin tuân thủ
RoHS, REACH, lead-free, and halogen-free statuses were not present in the verified web data; the part is obsolete and pre-dates many modern compliance disclosures. AEC-Q100 is not applicable as the part is specified for commercial 0C to +70C operation, not automotive grade.
