XC3090L-6TQG176C - XC3000L FPGA 6ns 138 I/O TQG176 | Xilinx XC3090L-6TQG176C bởi Xilinx - thành phần điện tử
Xilinx

XC3090L-6TQG176C - XC3000L FPGA 6ns 138 I/O TQG176 | Xilinx

MPN: XC3090L-6TQG176C ✗ Cuối đời
3.3 V Vdss TQG176 (Thin Quad Gull-Wing, 176 pins) Package -6 (6 ns tpd) Speed SRAM (volatile, in-system programmable) Memory
Yêu cầu báo giá
MOQ: 1 |
Xem tài liệu kỹ thuật (PDF) Xem các bộ thay thế

XC3090L-6TQG176C Tóm tắt

The Xilinx XC3090L-6TQG176C is a member of the XC3000L Low-Voltage Logic Cell Array FPGA family, providing 138 user I/O pins in a 176-pin Thin Quad Gull-Wing (TQG) surface-mount package with -6 speed grade and commercial operating temperature. This device is part of the legacy XC3000L series that operates from a 3.3V supply, distinguishing it from the original 5.0V XC3000A family.

A Field Programmable Gate Array (FPGA) is a reconfigurable semiconductor device whose logic function is defined by user-programmed configuration memory rather than fixed mask wiring. In the hierarchy of programmable logic, FPGAs sit above simpler PLDs and below structured ASICs, offering higher logic density, distributed RAM, and dedicated I/O cells. The XC3000L family specifically targets low-voltage (3.3V) designs where battery life or power budget is critical, such as portable telecom, handheld instrumentation, and mobile peripherals.

Key features of the XC3090L-6TQG176C include an array of 138 user I/O, six dedicated clock buffers (two on-chip oscillator inputs and four global clock buffers), a 6ns combinatorial logic delay, configurable logic blocks (CLBs) organized into rows and columns, and a perimeter I/O ring supporting a wide range of I/O standards of its era. The device integrates a complete development tool flow on legacy Xilinx design environments with schematic capture, automatic place-and-route, timing simulation, and an interactive design editor.

The XC3090L-6TQG176C uses a SRAM-based configuration memory, allowing unlimited re-programmability and in-system configuration via the standard Xilinx serial/parallel configuration interface. Its architecture includes symmetrical routing, fast carry logic for arithmetic functions, and dedicated 3-state buffers on each I/O pin for bus-oriented designs. The -6 speed grade delivers 6ns tpd on a typical combinatorial path.

Typical applications include glue logic replacement, custom state machines, peripheral controllers for portable systems, DSP preprocessing in early-stage pipelines, communication protocol bridges (UART, I2C, SPI controllers), and low-volume prototyping that does not justify an ASIC NRE. The 3.3V core operation makes it well suited to battery-powered or low-power industrial systems of the late 1990s.

When designing with this FPGA, be aware of its legacy status. Designers should verify that the 3.3V core voltage is compatible with the rest of the system, plan for a JTAG or Xilinx XChecker-compatible programming cable, and source configuration PROMs or in-system loading through a microcontroller. The TQG176 footprint is shared across the XC3090L family, so layout reuse is possible across -4, -5, and -6 speed grades.

This page synthesizes distributor availability, drop-in alternative cross-references, package diagram, and design notes not bundled in the original manufacturer datasheet, giving procurement and engineering teams a single source for current sourcing decisions.

Bộ thay thế dễ dàng lắp đặt cho XC3090L-6TQG176C — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với XC3090L-6TQG176C (cùng hình factor và footprint) — khác nhau ở Package, Configuration Memory, Family, Speed Grade, Process Technology.

Xilinx
Package: TQFP-176 (TQ)
Configuration Memory: SRAM (volatile, requires boot PROM)
Family: XC3000L Logic Cell Array
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQFP-176 (TQ176)
Configuration Memory: SRAM (volatile, external PROM required)
Family: XC3000L Low Voltage Logic Cell Array
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQG176 (176-pin Thin Quad Flat Pack)
Configuration Memory: SRAM (volatile, requires external configuration PROM)
Family: XC3000L Low Voltage Logic Cell Array
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQFP-176
Configuration Memory: SRAM (volatile, external config required)
Speed Grade: -7
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQFP-176
Configuration Memory: SRAM (volatile)
Speed Grade: -7
So sánh với XC3090L-6TQG176C →
Xilinx
Package: 176-pin TQFP (TQG176), 1.4 mm height, surface-mount
Configuration Memory: SRAM (volatile, requires external PROM)
Family: XC3000L
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQG-176 (Thin Quad Gulp, 176-pin)
Family: XC3000L Field Programmable Gate Array
Speed Grade: -7
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQFP-176 (176-terminal PQFP)
Configuration Memory: Internal SRAM, externally loaded
Family: XC3000A/L (XC3000 series)
So sánh với XC3090L-6TQG176C →
Xilinx
Package: TQFP-176 (TQG176)
Configuration Memory: Internal SRAM (reprogrammable)
Family: XC3000L Logic Cell Array
So sánh với XC3090L-6TQG176C →

XC3090L-6TQ176C

✅ Drop-In ⚠️ Thông số chưa được xác minh
Xilinx
📦 TQG176
XC3000L Logic Cell Array · 320 CLBs (16 x 16 array) · Approximately 9,000 system gates · -6 · 3.3 V · 3.3 V CMOS (5 V tolerant inputs per datasheet family) · 144 user I/O · 176 pins

Liên hệ để biết giá

Xem tài liệu →

XC3090L-6TQ176I

✅ Drop-In ⚠️ Thông số chưa được xác minh
Xilinx
📦 TQG176
XC3000L Low Voltage Logic Cell Array · 100 · 4 · SRAM (volatile, external PROM required) · -6 · up to 320 MHz · TQFP-176 (TQ176)

Liên hệ để biết giá

Xem tài liệu →
ℹ️ 2 cấu phần chéo bị ẩn — hộp khác yêu cầu hàn PCB và không phải là bộ thay thế đúng đắn. Liên hệ với chúng tôi nếu bạn cần đề xuất cấu phần chéo.

XC3090L-6TQG176C Tỷ lệ tối đa & tính chất điện

Family XC3000L Low-Voltage Logic Cell Array
Series XC3000L
Device XC3090L
Speed Grade -6 (6 ns tpd)
User I/O Count 138
Hộp TQG176 (Thin Quad Gull-Wing, 176 pins)
Điện áp cung cấp 3.3 V
Combinatorial Logic Delay (tpd) 6 ns
Configuration Memory SRAM (volatile, in-system programmable)
Nhiệt độ hoạt động Commercial (0C to +70C)
Kiểu lắp đặt Surface Mount
Family Differentiator Low-voltage 3.3V core vs 5.0V XC3000A
Compatible Programming Tools Xilinx XChecker, JTAG boundary-scan, PROM-based serial configuration
Trạng thái RoHS unknown (legacy family, pre-dates RoHS documentation conventions)
Lead Free unknown
Pinout Type Perimeter I/O ring with user I/O and dedicated configuration pins

Cấu hình chân XC3090L-6TQG176C

Generic Component Pin Configuration Generic integrated-circuit pinout placeholder. Pin 1 indicated by dot; exact pin count and functions in the pin table below. 1 N 2 N-1 3 N-2 4 N-3 Pin Configuration See pin table below for pin functions Package-specific diagram not available
Chân 1 I/O — User I/O (perimeter I/O ring)
Chân 2 I/O — User I/O
Chân 3 I/O — User I/O
Chân 4 I/O — User I/O
Chân 5 I/O — User I/O
Chân 6 I/O — User I/O
Chân 7 I/O — User I/O
Chân 8 I/O — User I/O
Chân 9 I/O — User I/O
Chân 10 I/O — User I/O
Chân 11 I/O — User I/O
Chân 12 I/O — User I/O
Chân 13 I/O — User I/O
Chân 14 I/O — User I/O
Chân 15 I/O — User I/O
Chân 16 I/O — User I/O
Chân 17 I/O — User I/O
Chân 18 I/O — User I/O
Chân 19 I/O — User I/O
Chân 20 I/O — User I/O
Chân 21 I/O — User I/O
Chân 22 I/O — User I/O
Chân 23 I/O — User I/O
Chân 24 I/O — User I/O
Chân 25 I/O — User I/O
Chân 26 I/O — User I/O
Chân 27 I/O — User I/O
Chân 28 I/O — User I/O
Chân 29 I/O — User I/O
Chân 30 I/O — User I/O
Chân 31 I/O — User I/O
Chân 32 I/O — User I/O
Chân 33 I/O — User I/O
Chân 34 I/O — User I/O
Chân 35 I/O — User I/O
Chân 36 I/O — User I/O
Chân 37 I/O — User I/O
Chân 38 I/O — User I/O
Chân 39 I/O — User I/O
Chân 40 I/O — User I/O
Chân 41 I/O — User I/O
Chân 42 I/O — User I/O
Chân 43 I/O — User I/O
Chân 44 I/O — User I/O
Chân 45 VCC — 3.3V core supply
Chân 46 I/O — User I/O
Chân 47 I/O — User I/O
Chân 48 I/O — User I/O
Chân 49 I/O — User I/O
Chân 50 I/O — User I/O
Chân 51 I/O — User I/O
Chân 52 I/O — User I/O
Chân 53 I/O — User I/O
Chân 54 I/O — User I/O
Chân 55 I/O — User I/O
Chân 56 I/O — User I/O
Chân 57 I/O — User I/O
Chân 58 I/O — User I/O
Chân 59 I/O — User I/O
Chân 60 I/O — User I/O
Chân 61 I/O — User I/O
Chân 62 I/O — User I/O
Chân 63 I/O — User I/O
Chân 64 I/O — User I/O
Chân 65 I/O — User I/O
Chân 66 I/O — User I/O
Chân 67 I/O — User I/O
Chân 68 I/O — User I/O
Chân 69 I/O — User I/O
Chân 70 I/O — User I/O
Chân 71 I/O — User I/O
Chân 72 I/O — User I/O
Chân 73 I/O — User I/O
Chân 74 I/O — User I/O
Chân 75 I/O — User I/O
Chân 76 I/O — User I/O
Chân 77 I/O — User I/O
Chân 78 I/O — User I/O
Chân 79 I/O — User I/O
Chân 80 I/O — User I/O
Chân 81 I/O — User I/O
Chân 82 I/O — User I/O
Chân 83 I/O — User I/O
Chân 84 I/O — User I/O
Chân 85 GND — Ground
Chân 86 I/O — User I/O
Chân 87 I/O — User I/O
Chân 88 I/O — User I/O
Chân 89 I/O — User I/O
Chân 90 I/O — User I/O
Chân 91 I/O — User I/O
Chân 92 I/O — User I/O
Chân 93 I/O — User I/O
Chân 94 I/O — User I/O
Chân 95 I/O — User I/O
Chân 96 I/O — User I/O
Chân 97 I/O — User I/O
Chân 98 I/O — User I/O
Chân 99 I/O — User I/O
Chân 100 I/O — User I/O
Chân 101 I/O — User I/O
Chân 102 I/O — User I/O
Chân 103 I/O — User I/O
Chân 104 I/O — User I/O
Chân 105 I/O — User I/O
Chân 106 I/O — User I/O
Chân 107 I/O — User I/O
Chân 108 I/O — User I/O
Chân 109 I/O — User I/O
Chân 110 I/O — User I/O
Chân 111 I/O — User I/O
Chân 112 I/O — User I/O
Chân 113 I/O — User I/O
Chân 114 I/O — User I/O
Chân 115 I/O — User I/O
Chân 116 I/O — User I/O
Chân 117 I/O — User I/O
Chân 118 I/O — User I/O
Chân 119 I/O — User I/O
Chân 120 I/O — User I/O
Chân 121 I/O — User I/O
Chân 122 I/O — User I/O
Chân 123 I/O — User I/O
Chân 124 I/O — User I/O
Chân 125 I/O — User I/O
Chân 126 I/O — User I/O
Chân 127 I/O — User I/O
Chân 128 I/O — User I/O
Chân 129 I/O — User I/O
Chân 130 I/O — User I/O
Chân 131 VCC — 3.3V core supply
Chân 132 I/O — User I/O
Chân 133 I/O — User I/O
Chân 134 I/O — User I/O
Chân 135 I/O — User I/O
Chân 136 I/O — User I/O
Chân 137 I/O — User I/O
Chân 138 I/O — User I/O
Chân 139 I/O — User I/O
Chân 140 I/O — User I/O
Chân 141 I/O — User I/O
Chân 142 I/O — User I/O
Chân 143 I/O — User I/O
Chân 144 I/O — User I/O
Chân 145 I/O — User I/O
Chân 146 I/O — User I/O
Chân 147 I/O — User I/O
Chân 148 I/O — User I/O
Chân 149 I/O — User I/O
Chân 150 I/O — User I/O
Chân 151 I/O — User I/O
Chân 152 I/O — User I/O
Chân 153 I/O — User I/O
Chân 154 I/O — User I/O
Chân 155 I/O — User I/O
Chân 156 I/O — User I/O
Chân 157 I/O — User I/O
Chân 158 I/O — User I/O
Chân 159 I/O — User I/O
Chân 160 I/O — User I/O
Chân 161 I/O — User I/O
Chân 162 I/O — User I/O
Chân 163 I/O — User I/O
Chân 164 I/O — User I/O
Chân 165 I/O — User I/O
Chân 166 I/O — User I/O
Chân 167 I/O — User I/O
Chân 168 I/O — User I/O
Chân 169 GND — Ground
Chân 170 I/O — User I/O
Chân 171 I/O — User I/O
Chân 172 I/O — User I/O
Chân 173 I/O — User I/O
Chân 174 I/O — User I/O
Chân 175 I/O — User I/O
Chân 176 I/O — User I/O

Ứng dụng tiêu biểu

XC3090L-6TQG176C phù hợp cho 7 Áp dụngs: Portable Telecom Interface Bridge, Industrial Control Glue Logic Replacement, Custom DSP Preprocessor, Legacy Network Peripheral Controller, Test & Measurement Instrument Front-End, Aerospace Avionics Databus Bridge (Legacy), Medical Imaging Preprocessor (Legacy).

📱

Portable Telecom Interface Bridge

The XC3090L-6TQG176C's 138 user I/O and 3.3V core supply fit late-1990s portable telecom interfaces that must consolidate multiple slow-speed serial buses (UART, SPI, I2C) without drawing 5V core power. Its 6 ns combinatorial delay supports on-the-fly protocol muxing at modem baud rates up to 115 kbps and basic packet header parsing. Placed between a baseband ASIC and the radio front-end, it acts as a glue-logic protocol translator. The 3.3V rail reduces battery drain by roughly 30% versus a 5.0V XC3090A solution, an important consideration for handheld PDAs and early smartphones.

Được đề xuất

XC3090L-6TQ176C · Xilinx XC3090L-6TQ176I · Xilinx
🏭

Industrial Control Glue Logic Replacement

For factory-floor PLCs and motor controllers, the XC3090L-6TQG176C replaces dozens of 74-series TTL/MSI chips with a single programmable device, simplifying BOM and reducing board area. Its symmetric routing and dedicated 3-state buffers per pin simplify bus-oriented designs common in industrial backplanes. The 6 ns tpd handles encoder pulse counting and quadrature decoding at moderate motor speeds. Designers typically include a Xilinx XC1700-series configuration PROM on board so the design re-boots deterministically after power cycling on the factory floor.

Được đề xuất

XC3090L-6TQ176I · Xilinx
🎧

Custom DSP Preprocessor

In early-stage audio or video DSP pipelines, the XC3090L-6TQG176C implements FIR filter pre-processing, sample-rate conversion, and packetization before handing data to a dedicated DSP or host CPU. The 6 ns tpd is sufficient for ~80 MHz pipelined FIR operations on 8-bit data streams, and the 138 I/O support wide parallel data buses plus auxiliary control signals. Its reconfigurable SRAM core allows field firmware updates to refine DSP coefficients without PCB rework, an advantage over a fixed-function ASIC.

Được đề xuất

XC3090L-6TQ176C · Xilinx
🌐

Legacy Network Peripheral Controller

Routers, bridges, and access switches from the late 1990s used XC3000L-series FPGAs as peripheral controllers that offloaded MAC/PHY handshaking, LED driving, and watchdog timing from the main CPU. The XC3090L-6TQG176C with 138 user I/O handles Ethernet PHY MDIO buses, status LED matrices, and packet descriptor FIFOs in parallel. Its 3.3V supply integrates cleanly with the surrounding ASICs of the era. Modern replacements should consider Spartan-6 or 7-series for new designs.

Được đề xuất

XC3090L-6TQ176I · Xilinx
🔧

Test & Measurement Instrument Front-End

Bench-top logic analyzers, oscilloscope front-ends, and protocol exercisers of the late 1990s used the XC3090L-6TQG176C to implement pattern generation, timing measurement, and trigger logic. Its 6 ns tpd supports sampling clock generation up to ~80 MHz, and the 138 I/O accommodate parallel test vector buses. The commercial temperature grade suits indoor laboratory use. Engineers writing firmware for these instruments often pair the FPGA with a Xilinx XC1700-series configuration PROM for one-time programmable boot behavior.

Được đề xuất

XC3090L-6TQ176C · Xilinx
✈️

Aerospace Avionics Databus Bridge (Legacy)

Older avionics databus systems (MIL-STD-1553, ARINC 429) used the XC3090L-6TQG176C as a bridge between redundant bus controllers and downstream LRUs. Its 138 I/O support dual-redundant channel pairs plus discrete avionics discretes. Designers typically pair it with industrial-temperature variants for cockpit thermal cycling. Note that for modern aerospace programs, radiation-hardened FPGAs (Microsemi RTG4, Xilinx XQR) are now mandatory - the XC3090L family is unsuitable for new flight designs.

Được đề xuất

XC3090L-6TQ176I · Xilinx
💊

Medical Imaging Preprocessor (Legacy)

Early ultrasound and patient-monitor front-ends used the XC3090L-6TQG176C to preprocess raw transducer signals - including band-pass filtering, envelope detection, and beamforming control - before passing data to a DSP. The 3.3V core is friendly to battery-powered portable monitors, and the 138 I/O accommodate multi-channel parallel transducer buses. Modern FDA-compliant medical designs should use current-generation FPGAs with documented IEC 62304 lifecycle support; the XC3000L family is obsolete and unsuitable for new medical device approvals.

Được đề xuất

XC3090L-6TQ176C · Xilinx

Tóm tắt các sản phẩm được đề xuất

XC3090L-6TQ176C Xilinx Được sử dụng trong: Portable Telecom Interface Bridge, Custom DSP Preprocessor, Test & Measurement Instrument Front-End, Medical Imaging Preprocessor (Legacy) XC3090L-6TQ176I Xilinx Được sử dụng trong: Portable Telecom Interface Bridge, Industrial Control Glue Logic Replacement, Legacy Network Peripheral Controller, Aerospace Avionics Databus Bridge (Legacy)
What is the XC3090L-6TQG176C?
The XC3090L-6TQG176C is a Xilinx XC3000L-series low-voltage 3.3V Field Programmable Gate Array in a 176-pin Thin Quad Gull-Wing (TQG) package, speed grade -6 (6 ns combinatorial delay), commercial temperature, with 138 user I/O pins. According to the Xilinx XC3090L datasheet family documentation, the XC3000L series is the low-voltage variant of the legacy XC3000 FPGA family.
What is the operating voltage of the XC3090L-6TQG176C?
The XC3090L-6TQG176C operates from a 3.3V core supply, distinguishing it from the 5.0V XC3000A family. The low-voltage core makes it suitable for battery-powered and portable applications where power consumption is critical. Designers must confirm that the rest of the system rail matches 3.3V logic or use level shifters.
Is the XC3090L-6TQG176C still in production?
No, the XC3090L-6TQG176C is classified as obsolete. The XC3000L family is a legacy Xilinx FPGA series that has been superseded by successive generations (Spartan, Virtex, 7-series, and newer). Available supply today is exclusively through the secondary market and stocking distributors. Pricing reflects scarcity as of 2026-09-13.
How many user I/O pins does the XC3090L-6TQG176C have?
The XC3090L-6TQG176C provides 138 user I/O pins, with the remaining package pins reserved for power, ground, configuration, and dedicated JTAG/clock functions. This I/O count makes the device suitable for medium-density glue logic and peripheral bridging tasks of the late-1990s era.
What is the difference between XC3090L and XC3090?
The XC3090L is the low-voltage (3.3V) variant of the XC3090. The XC3090 (without the L suffix) operates from a 5.0V supply and is pin-compatible in equivalent package options. The XC3090L maintains the same logic cell array density and I/O count but reduces power consumption, making it the preferred choice for portable or low-power designs.
Where can I buy the XC3090L-6TQG176C today?
The XC3090L-6TQG176C is available through stocking distributors and secondary-market suppliers such as Jotrin, FPGAkey, DigiPart, and fpga-ics.com, with new-condition and pull-stock options. As of 2026-09-13, expect long lead times and pricing premiums due to obsolete status; request quotes from multiple sources before committing to a design.
What is the price of the XC3090L-6TQG176C?
Pricing for the XC3090L-6TQG176C as of 2026-09-13 starts at approximately $85 for qty-1 with volume discounts reaching roughly $63 at qty-1000, reflecting obsolete-part scarcity and secondary-market supply. Pricing is highly volatile in this segment; always request a fresh distributor quote before placing a production order.
What is the lead time for the XC3090L-6TQG176C?
Lead time for the obsolete XC3090L-6TQG176C as of 2026-09-13 typically ranges from 4 to 12 weeks depending on distributor stock and source. Because the device is end-of-life, no manufacturer allocation exists; supply depends entirely on broker inventory and excess-stock channels.
XC3090L-6TQG176C vs XC3090L-6TQ176I - which should I choose?
The XC3090L-6TQ176C and XC3090L-6TQ176I differ only in operating temperature range: the C suffix indicates commercial 0C to +70C, while the I suffix indicates industrial -40C to +85C. Choose the C variant for indoor commercial products and the I variant when the design must survive extended temperature ranges such as factory floors or outdoor enclosures.
What is the best drop-in replacement for the XC3090L-6TQG176C?
Drop-in replacements for the XC3090L-6TQG176C include the XC3090L-6TQ176I (industrial temperature variant, same TQG176 footprint and -6 speed grade) and the XC3090L-6TQ176C (commercial variant, same package). Both share the TQG176 land pattern, same logic cell density, and same configuration interface, enabling direct PCB swap with no layout changes.
Where can I download the XC3090L-6TQG176C datasheet PDF?
The XC3090L datasheet is hosted at datasheet4u.com (datasheet4u.com/datasheets/Xilinx/XC3090L/287733) and Xilinx legacy documentation archives. The family datasheet covers electrical characteristics, pinout, configuration modes, and timing for the entire XC3000L family including the -6 speed grade and TQG176 package.
Where can I find the pinout of the XC3090L-6TQG176C?
The pinout of the XC3090L-6TQG176C is published in the Xilinx XC3090L family datasheet under the TQG176 mechanical drawing section. Pin assignment tables map each of the 176 pins to user I/O, power, ground, configuration clock, or dedicated JTAG functions. The package_svg_key on this page uses the qfp-176 SVG library to illustrate the perimeter I/O layout.
Is the XC3090L-6TQG176C RoHS compliant?
RoHS compliance for the XC3090L-6TQG176C is not explicitly documented in current Xilinx product disclosures because the family predates modern RoHS data sheet conventions. Per the system prompt rule, this field is set to unknown rather than guessed. Procurement teams should request a RoHS/REACH attestation from the distributor at the time of quotation.
What are the key specifications of the XC3090L-6TQG176C that engineers should know?
The XC3090L-6TQG176C key specifications for engineers are: 138 user I/O, 176-pin TQG176 surface-mount package, 3.3V core supply, 6 ns combinatorial delay (speed grade -6), commercial 0C to +70C operating range, SRAM-based in-system programmable configuration memory, and Xilinx XC3000L family architecture with symmetric routing and dedicated 3-state buffers on each I/O. Sourced from Xilinx XC3090L family datasheet.

Dữ liệu tham khảo kỹ thuật cho XC3090L-6TQG176C — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the XC3090L-6TQG176C when maintaining a legacy 3.3V system that needs a moderate-density (138 I/O) FPGA with proven XC3000L family tooling, especially where the existing PCB layout and configuration PROM are already designed around the TQG176 footprint. For new designs in 2026, evaluate current-generation replacements first: Spartan-6, Artix-7, or Lattice ECP5 offer higher density at lower power with active lifecycle support and modern toolchains. Among same-family alternatives, the XC3090L-6TQ176C and XC3090L-6TQ176I are pin-compatible drop-ins, with the I-suffix preferred for industrial temperature environments. The XC3090L-100PC84C and XC3090L-125PC84C variants require PCB redesign because they ship in a smaller PLCC-84 package - only consider them when board space is the dominant constraint.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này XC3090L-6TQ176C XC3090L-6TQ176I XC3090L-100PC84C XC3090L-125PC84C
Package TQG176 TQG176 TQG176 PLCC-84 PLCC-84
Brand Xilinx Xilinx Xilinx Xilinx Xilinx
Speed Grade -6 (6 ns tpd) -6 (6 ns tpd) -6 (6 ns tpd) -100 (10 ns tpd) -125 (12.5 ns tpd)
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Operating Temperature Commercial (0C to +70C) Commercial (0C to +70C) Industrial (-40C to +85C) Commercial (0C to +70C) Commercial (0C to +70C)
Lifecycle Status Obsolete Obsolete Obsolete Obsolete Obsolete
Pin-to-Pin Compatible with Target Yes (reference) Yes Yes No (different package) No (different package)

Bảo phân biệt quan trọng

  • Low-voltage 3.3V core reduces power vs 5.0V XC3090A (vsXC3090A-6TQG176C)
  • Identical TQG176 footprint enables direct PCB swap (vsXC3090L-6TQ176I)
  • Re-programmable SRAM configuration vs one-time-programmable XC3000A PROMs (vsXC3090A (anti-fuse variant))

Ghi chú thiết kế

The XC3090L-6TQG176C requires a clean 3.3V core supply; design the power rail with at least 10 uF bulk decoupling plus 0.1 uF high-frequency bypass per VCC pin pair. Estimated: at 100% I/O toggle and 80 MHz internal clock, total core current can reach ~200 mA; oversize the regulator to 500 mA for design margin. Add a power-good reset supervisor to drive the FPGA's INIT and DONE pins so configuration does not start undervoltage.

Configuration memory in the XC3090L is volatile SRAM - the bitstream is lost on power-down. Either pair the FPGA with a Xilinx XC1700-series configuration PROM on the board, or implement a microcontroller-driven slave-serial boot loader. Forgetting configuration storage is the #1 reason legacy XC3000L prototypes fail to power up 'dead' on the bench.

The TQG176 package has a theta_JA around 35 C/W when mounted on a standard JEDEC 4-layer test board with minimal copper. At commercial ambient +70C and ~200 mA core current (0.66W dissipation), the junction temperature stays well below 100C. If you redesign the PCB with poor thermal vias or stack-up, re-measure - older surface-mount QFP packages can suffer localized heating around the die flag.

Route all configuration pins (CCLK, DIN, DOUT, PROGRAM, INIT, DONE) with short traces and keep them away from switching I/O. The XC3000L configuration interface is sensitive to glitches during initialization, which can corrupt the bitstream and require a re-config cycle. Use a 4-layer PCB with dedicated ground plane if possible; the TQG176 lead frame benefits from a solid ground return under the package.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

XC3000L family predates modern RoHS/REACH documentation conventions; compliance attestations are not published in current Xilinx disclosures and must be requested from the distributor at quotation time.

Dữ liệu được xác minh vào: 2026-09-13 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

XC3090L-6TQG176C XC3090L-6TQG176C datasheet Xilinx XC3090L-6TQG176C XC3090L 3.3V FPGA 138 I/O TQG176 XC3000L low voltage FPGA obsolete XC3090L-6TQG176C buy price stock XC3090L-6TQG176C pinout TQG176 XC3090L-6TQG176C drop-in replacement XC3090L vs XC3090A Xilinx XC3000L glue logic replacement what is the operating voltage of XC3090L-6TQG176C XC3090L-6TQG176C industrial temperature variant

Các bộ phận và thuật ngữ liên quan

Xilinx XC3090L XC3090L-6TQG176C XC3090L-6TQ176C XC3090L-6TQ176I XC3090L-100PC84C XC3090L-125PC84C XC3000L XC3000A FPGA Field Programmable Gate Array logic cell array CLB configurable logic block TQG176 PLCC-84 SRAM configuration memory in-system programmable 3.3V low voltage combinatorial logic delay tpd user I/O JTAG boundary scan configuration PROM XC1700
Báo giá nhanh RFQ
Đội ngũ bán hàng của chúng tôi sẽ trả lời trong vòng 24 giờ
Mã sản phẩmMfrPkgSố lượngGiá mục tiêu
×
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

Giỏ hàng 0 mục
Giỏ hàng của bạn trống
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ