IAUTN04S7N004ATMA1 - 40V 0.38mΩ 350A OptiMOS 7 | Infineon
料号： IAUTN04S7N004ATMA1 ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $9.85 | $9.85 |
| 10 | $8.92 | $89.20 |
| 100 | $7.65 | $765.00 |
| 500 | $6.8 | $3,400.00 |
| 1,000 | $6.05 | $6,050.00 |
IAUTN04S7N004ATMA1 概述
A power MOSFET is a voltage-controlled semiconductor switch that uses a gate signal to modulate conduction between its drain and source terminals, enabling efficient power conversion in switched-mode topologies. As a category, MOSFETs (Metal-Oxide-Semiconductor Field-Effect Transistors) belong to the broader family of discrete transistors within power semiconductors, sitting alongside IGBTs and thyristors. The 40 V OptiMOS 7 generation specifically targets low-voltage automotive powertrain, chassis, and body-electronics applications where efficiency, thermal performance, and reliability directly affect vehicle range and system cost.
The IAUTN04S7N004's 0.38 mΩ RDS(on) minimizes I²R losses at high currents, while the optimized gate-charge (Qg) and low Qgd/Qgs ratios reduce switching losses in high-frequency DC-DC and BLDC motor-drive stages. Its AEC-Q101-qualified construction, lead-free PG-HSOF-8-8 package with exposed top-cooling pad, and 175°C maximum junction temperature support the harsh automotive under-hood environment. The device also features a logic-level gate-threshold compatible with microcontroller GPIO drivers.
Typical applications include 12 V/24 V automotive BLDC motor drives (EPS, pumps, fans), 48 V mild-hybrid DC-DC converters, battery protection switches, and high-current solenoid/relay drivers. The combination of very low on-resistance and surface-mount TOLL footprint enables compact, high-power-density designs where traditional D2PAK parts would be too large.
When designing with the IAUTN04S7N004, pay close attention to PCB layout: minimize the high-current loop (drain-source) and gate-drive loop to control parasitic inductance that causes voltage overshoot during turn-off. A 10 Ω gate resistor typically suffices; values below 5 Ω risk ringing, while values above 50 Ω slow switching and increase losses. Thermal management via the top-exposed thermal pad is essential at sustained currents above 200 A.
The TOLL (TO-Leadless) 10x12 mm package provides an RthJC substantially lower than DPAK, enabling 255 W power dissipation with proper PCB copper thermal vias under the exposed pad. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not collected in the manufacturer datasheet alone.
直接替换替代料： IAUTN04S7N004ATMA1 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： IAUTN04S7N004ATMA1 （相同外形与封装尺寸） ——差异在于 Package, Mounting Type, Automotive Qualification, Technology, Product Family.
快速对比工具——选择替代料号进行并排对比：
IAUCN04S7N004ATMA1
✅ 直接替换📋 参考替代料（不在目录中）
IAUC60N04S6L030HATMA1
✅ 直接替换✓ 有现货
$0.94 / 个
查看数据手册 →IAUCN04S7N015GATMA1
✅ 直接替换✓ 有现货
$2.21 / 个
查看数据手册 →IAUCN04S7N019GATMA1
✅ 直接替换✓ 有现货
$0.82 / 个
查看数据手册 →IAUCN04S7N027GATMA1
✅ 直接替换✓ 有现货
$0.72 / 个
查看数据手册 →IAUCN04S7N037GATMA1
✅ 直接替换✓ 有现货
$0.89 / 个
查看数据手册 →IAUCN04S7L042GATMA1
✅ 直接替换✓ 有现货
$0.86 / 个
查看数据手册 →IAUTN04S7N004ATMA1 最大额定值与电气特性
| Manufacturer | Infineon Technologies |
| Product Family | OptiMOS 7 |
| Technology | N-Channel Trench MOSFET |
| Drain-Source Voltage (VDS) | 40 V |
| Continuous Drain Current (ID) at Tj | 350 A |
| On-Resistance RDS(on) max | 0.38 mΩ |
| Power Dissipation (PD) at TC | 255 W |
| 工作温度范围 | -55C to +175C |
| 封装 | PG-HSOF-8-8 (TOLL 10x12) |
| 安装类型 | Surface Mount |
| Qualification | AEC-Q101 Automotive |
| RoHS 状态 | Compliant |
| Lead-Free | Yes |
| Polarity | N-Channel |
IAUTN04S7N004ATMA1 引脚配置
| 引脚 1 | Drain — Power drain (pad) |
| 引脚 2 | Drain — Power drain (pad) |
| 引脚 3 | Gate — Gate control input |
| 引脚 4 | Source — Source return path |
| 引脚 5 | Source — Source return path |
| 引脚 6 | Drain — Power drain (pad) |
| 引脚 7 | Drain — Power drain (pad) |
| 引脚 8 | Thermal Pad — Top-exposed thermal pad (electrically floating or source depending on datasheet variant) |
安全工作区 (DC)
典型应用
IAUTN04S7N004ATMA1 适用于 6 应用s: Automotive BLDC Motor Drive (EPS, Pumps, Fans), 48V Mild-Hybrid DC-DC Converter, Battery Disconnect / Protection Switch, High-Current Solenoid and Relay Driver, Industrial High-Current Switching, Robotics and Servo Drive Systems.
Automotive BLDC Motor Drive (EPS, Pumps, Fans)
The IAUTN04S7N004ATMA1's 0.38 mΩ RDS(on) and 350 A continuous drain current make it ideal for automotive brushless DC motor drives including electric power steering, oil pumps, water pumps, and cooling fans. In a typical 3-phase inverter topology, the device handles phase currents up to 200 A peak with minimal conduction loss. The TOLL package enables compact inverter designs where D2PAK parts would be too large. AEC-Q101 qualification ensures reliability under hood at 105C ambient.
推荐
48V Mild-Hybrid DC-DC Converter
In 48V mild-hybrid DC-DC converters stepping between 48V and 12V buses, the IAUTN04S7N004ATMA1's low RDS(on) directly improves converter efficiency. At 100 A continuous current, the device dissipates only 3.8 W (I²R), enabling peak efficiencies above 97% in well-designed buck/boost stages. The 40 V VDS rating provides margin against 48V bus transients, and the TOLL footprint supports the high power density required for underbody-mounted converters.
推荐
Battery Disconnect / Protection Switch
The IAUTN04S7N004ATMA1 serves as a battery disconnect switch in 12V/24V automotive systems, replacing mechanical contactors with solid-state reliability. Its 350 A continuous rating covers cranking currents (typically 200-300 A peak), while the 0.38 mΩ on-resistance minimizes voltage drop during high-current events. The AEC-Q101 qualification and -55C to +175C operating range ensure operation in extreme under-hood environments.
推荐
High-Current Solenoid and Relay Driver
For driving high-current automotive solenoids (transmission shift solenoids, valve actuators, EV contactors), the IAUTN04S7N004ATMA1 provides the low RDS(on) needed for high inrush current handling. Its surface-mount TOLL package eliminates the bulky TO-220 through-hole footprint, enabling PCB-side integration. Fast switching speeds (sub-50 ns) minimize switching losses in PWM-driven solenoid applications up to 20 kHz.
推荐
Industrial High-Current Switching
Outside automotive, the IAUTN04S7N004ATMA1 suits industrial high-current switching applications including welding equipment, large UPS battery banks, and motor drives. The 255 W power dissipation rating combined with the top-cooled TOLL package supports sustained operation at currents well above what TO-220 parts can handle. Engineers can mount the device to a heat sink via the top thermal pad for maximum heat extraction.
推荐
Robotics and Servo Drive Systems
In robotics servo drives and AGV traction motors, the IAUTN04S7N004ATMA1's combination of low RDS(on), fast switching, and small TOLL footprint enables compact high-power drive stages. The device supports PWM frequencies to 100 kHz with manageable switching losses, enabling tight current-loop control. Multiple devices in parallel can scale to kW-level servo drives while maintaining a small board footprint compared to D2PAK designs.
推荐
推荐产品汇总
工程参考数据： IAUTN04S7N004ATMA1 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | IAUCN04S7N004ATMA1 | IAUC60N04S6L030HATMA1 | IAUCN04S7N015GATMA1 | IAUCN04S7N019GATMA1 |
|---|---|---|---|---|---|
| Package | PG-HSOF-8-8 (TOLL 10x12) | PG-HSOF-8-8 (TOLL 10x12) - same | PG-HSOF-8-8 (TOLL 10x12) - same | PG-HSOF-8-8 (TOLL 10x12) - same | PG-HSOF-8-8 (TOLL 10x12) - same |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| VDS max | 40 V | 40 V | 40 V | 40 V | 40 V |
| RDS(on) max at VGS=10V | 0.38 mΩ | 0.44 mΩ | 0.30 mΩ | 0.15 mΩ | 0.19 mΩ |
| AEC-Q101 Automotive | Yes | Yes | Yes | Yes | Yes |
| Technology Generation | OptiMOS 7 | OptiMOS 7 | OptiMOS 6 | OptiMOS 7 | OptiMOS 7 |
关键差异点
- Higher continuous drain current rating at junction （对比 IAUCN04S7N004ATMA1)
- Lower on-resistance than OptiMOS 7 direct equivalent （对比 IAUCN04S7N004ATMA1)
- Newer OptiMOS 7 generation vs older OptiMOS 6 （对比 IAUC60N04S6L030HATMA1)
设计说明
Estimated: At continuous ID=200 A and RDS(on)=0.38 mΩ, conduction loss is approximately 15.2 W per device. Using the TOLL package's RthJC of approximately 0.5 C/W, junction temperature rises 7.6°C above the case. With proper thermal vias (12+ 0.3 mm vias under the exposed pad) connecting to a 2 oz inner copper plane, RthJA drops to roughly 35 C/W, allowing sustained 200 A operation in still air at 85°C ambient. Always verify with a thermal probe in the final assembly.
The TOLL (PG-HSOF-8-8) package requires careful PCB layout to achieve its rated performance. The drain pads (4 of 8) must connect to a wide, thick copper pour (≥2 oz, 50 mm wide) to carry the high current. The source pads need a separate large copper area. The top-exposed thermal pad should be soldered to a heatsink or top-side copper plane for maximum heat extraction. Gate trace width of 0.5 mm is adequate; minimize loop area between gate and source pads to reduce ringing.
Common pitfalls with the IAUTN04S7N004ATMA1 include: (1) insufficient gate-drive voltage - logic-level signals may not fully enhance the device, leaving it in the linear region with high RDS(on); always drive VGS to at least 10 V for full enhancement; (2) missing TVS protection on the 12V/24V bus - load-dump transients can exceed 40 V and destroy the MOSFET; (3) omitting the gate-source pull-down resistor - a 10 kΩ resistor from gate to source prevents false turn-on during transients.
Minimize the high-current loop (drain-source) by placing input capacitors, MOSFET, and load in a tight triangular layout. The gate-drive loop should be separate and small, ideally 5 mm or less, with the gate resistor placed close to the gate pin. Use a kelvin source connection if available to eliminate source-inductance-induced gate-drive errors. For paralleled devices, symmetric PCB layout ensures balanced current sharing and prevents thermal runaway.
合规信息
AEC-Q101 automotive qualified per Infineon datasheet (AEC-Q100 designation is for ICs, not discrete MOSFETs - use AEC-Q101 for this part). RoHS and REACH compliant per Infineon product page.
