TPSM82866A - 6A Step-Down Power Module | Texas Instruments
MPN: TPSM82866AA0SRDJR β Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $5.2 | $5.20 |
| 10 | $4.68 | $46.80 |
| 100 | $4.16 | $416.00 |
| 500 | $3.75 | $1,875.00 |
| 1,000 | $3.4 | $3,400.00 |
Drop-in alternatives for TPSM82866AA0SRDJR β same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Quick Comparison Tool β Select alternative parts for side-by-side comparison:
TPSM82864AA0SRDJR
β Drop-Inπ Reference alternative (not in catalog)
TPSM82866AA0HRDMR
β Drop-Inπ Reference alternative (not in catalog)
TPSM82866AA0SRDJR Maximum Ratings & Electrical Characteristics
| Topology | Synchronous Step-Down (Buck) Module |
| Input Voltage Range | 2.4 V to 5.5 V |
| Output Voltage Range | 0.6 V to 5.5 V (adjustable) |
| Output Current | 6 A |
| Control Topology | DCS-Control |
| Integrated Inductor | 220 nH (RDJ/RDM), Β±20% tolerance |
| Number of Outputs | 1 |
| Package | Overmolded QFN (RDJ) 3.5 mm x 4.0 mm |
| Mounting Type | Surface Mount |
| Features | Enable, Power Good, Soft-Start, Integrated Inductor |
| Applications | FPGA/CPU/ASIC core supply, optical modules, medical, industrial |
| Type | Non-Isolated PoL Module |
| Isolation | Non-Isolated |
| Pin Compatibility | Pin-to-pin and BOM-to-BOM compatible with TPSM82864A (RDJ/RDM) |
| RoHS Status | Compliant |
| Operating Temperature | [DATA_NEEDED: operating temperature range] |
TPSM82866AA0SRDJR Pin Configuration
| Pin 1 | PVIN β Power input supply (2.4V to 5.5V) |
| Pin 2 | EN β Enable pin |
| Pin 3 | RT/CLK β Frequency set / synchronization |
| Pin 4 | SS/TR β Soft-start / tracking |
| Pin 5 | VSENSE β Feedback voltage sense |
| Pin 6 | AGND β Analog ground |
| Pin 7 | PGND β Power ground |
| Pin 8 | SW β Switch node (internal inductor) |
| Pin 9 | VOUT β Regulated output (0.6V to 5.5V) |
| Pin 10 | PGOOD β Power good indicator (open drain) |
| Pin 11 | VIN β Analog input supply |
| Pin 12 | NC/GND β [DATA_NEEDED: exact pin functions - consult datasheet SLUSEF1B] |
Safe Operating Area (SOA) & Thermal Characteristics
No official SOA curve available for this component. Always operate within absolute maximum ratings specified in the datasheet. Ensure adequate cooling and derate as needed.
Typical Applications
TPSM82866AA0SRDJR is suitable for 6 applications: FPGA Core Power Supply, CPU / ASIC Point-of-Load, Optical Modules, Medical Equipment, Industrial Automation, Test and Measurement Instruments.
FPGA Core Power Supply
The TPSM82866A fits FPGA core rails (0.6V-1.0V typ) with its 6A continuous output and DCS-Control fast transient response, which handles the sharp load steps of block enable/disable events. The integrated 220nH inductor and small 3.5mm x 4.0mm footprint allow placement directly beside the FPGA power pins, reducing parasitic impedance. Place it between a 5V or 3.3V rail and the VCCINT pin with adequate ceramic output capacitance; the trade-off is verifying thermal vias under the QFN for full-load dissipation.
Recommended
CPU / ASIC Point-of-Load
For processor core supplies, the TPSM82866A provides 6A from a 2.4V-5.5V bus with power-good output for sequencing supervision and an enable pin for rail ordering. DCS-Control topology delivers fast load transient response needed by bursty digital cores, while the shielded integrated inductor reduces EMI near sensitive logic. The pin-to-pin compatible 4A TPSM82864A lets one PCB serve multiple processor tiers. Design consideration: size input capacitance for the 5V rail RMS ripple current at full 6A load.
Recommended
Optical Modules
Optical transceiver modules demand compact, efficient power conversion in tight form factors such as QSFP and OSFP. The TPSM82866A's 3.5mm x 4.0mm overmolded QFN with integrated inductor fits these height- and area-constrained boards, and its shielded magnetics limit EMI near high-speed serializer circuits. Operating from a 3.3V or 5V host rail, it powers laser driver and DSP cores at up to 6A. The MagPack RCF variant offers even better EMI shielding where optical link margins are tight.
Recommended
Medical Equipment
Medical electronics such as patient monitors and portable diagnostics benefit from the TPSM82866A's small footprint, integrated shielding, and wide 2.4V-5.5V input that tolerates battery rail variation. The power-good flag supports safety monitoring of the supply rail, and soft-start limits inrush during power-up of sensitive front-end circuitry. Its high efficiency reduces thermal load inside sealed enclosures. Designers should confirm creepage/clearance and isolation requirements elsewhere in the chain, since the module itself is non-isolated.
Recommended
Industrial Automation
In industrial control and factory automation, 24V buses are typically pre-regulated to 5V, from which the TPSM82866A generates low-voltage digital rails at 6A. Its DCS-Control architecture maintains stable operation with a wide range of output capacitor types, and the enable/power-good pins support fault handling in multi-rail systems. The integrated inductor saves board area on dense I/O and PLC boards. Consider the HRDMR variant for higher efficiency in elevated-ambient control cabinets.
Recommended
Test and Measurement Instruments
Bench instruments and modular test systems need clean, high-current local rails for FPGAs, ADCs, and processors. The TPSM82866A's shielded integrated inductor and DCS-Control low-output-ripple operation minimize switching noise coupling into sensitive measurement paths, while the compact footprint supports dense multi-rail designs. Its evaluation module (TPSM82866AA0SEVM) speeds up prototyping. Pair with low-noise LDOs on the most noise-critical analog rails where ultimate PSRR matters.
Recommended
Recommended Products Summary
Engineering reference data for TPSM82866AA0SRDJR β comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | TPSM82864AA0SRDJR | TPSM82866AA0HRDMR | TPSM82866AA0PRCFR | ISL8200AMIRZ |
|---|---|---|---|---|---|
| Package | Overmolded QFN (RDJ) 3.5x4.0 mm | Overmolded QFN (RDJ) 3.5x4.0 mm - same | Overmolded QFN (RDM), taller | QFN (RCF MagPack) | Renesas QFN module (different) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Renesas Electronics |
| Output Current | 6 A | 4 A | 6 A | 6 A | 5 A class |
| Input Voltage Range | 2.4 V to 5.5 V | 2.4 V to 5.5 V | 2.4 V to 5.5 V | 2.4 V to 5.5 V | [DATA_NEEDED] |
| Output Voltage Range | 0.6 V to 5.5 V | 0.6 V to 5.5 V | 0.6 V to 5.5 V | 0.6 V to 5.5 V | [DATA_NEEDED] |
| Control Topology | DCS-Control | DCS-Control | DCS-Control | DCS-Control | [DATA_NEEDED] |
| Integrated Inductor | 220 nH (Β±20%) | 220 nH (Β±20%) | 220 nH, taller/efficient | 200 nH MagPack | [DATA_NEEDED] |
| EMI Performance | Shielded inductor | Shielded inductor | Shielded inductor | Best (MagPack full shield) | [DATA_NEEDED] |
| Footprint Compatibility | Reference (RDJ) | Pin-to-pin, BOM-to-BOM compatible | Pin-compatible, taller body | Different (RCF footprint) | Not pin-compatible (PCB rework) |
Key Differentiators
- Higher current on identical footprint (vs TPSM82864AA0SRDJR)
- Higher efficiency package option (vs TPSM82866AA0SRDJR (this thin RDJ))
- Superior EMI shielding option (vs TPSM82866AA0PRCFR)
Design Notes
Although the TPSM82866A integrates the inductor, layout still matters. Place low-ESR ceramic input capacitors as close as possible to PVIN/PGND; follow the layout example in TI datasheet SLUSEF1B. Use solid ground planes with thermal vias under the exposed pad to conduct heat away from the 3.5mm x 4.0mm QFN at full 6A load. Keep the VSENSE feedback trace away from the SW node and route it as a Kelvin connection to the output capacitor.
At 6A output with a large VIN-VOUT difference, module dissipation rises and the small QFN package relies on PCB copper for cooling. Estimate losses from the datasheet efficiency curves for your operating point, and provide adequate copper area and via arrays to the ground plane. If ambient temperature is high or airflow is limited, consider the TPSM82866AA0HRDMR variant, which achieves higher efficiency due to its increased height and improved inductor.
Do not exceed the 5.5V maximum input rating. Size output capacitance per the datasheet stability guidelines; the DCS-Control topology is flexible with capacitor type but requires minimum effective capacitance for stability at high output current. Remember the integrated inductor is 220nH Β±20% - output ripple and transient behavior depend on this value, so do not assume discrete-design ripple calculations. Use the TPSM82866AA0SEVM to validate before committing to a layout.
Compliance Information
RoHS compliant per TI product page. Full REACH/halogen status: consult TI quality/environmental data on ti.com.
