LTC2184IUP - 16-Bit 105Msps Dual ADC, 64-QFN | Analog Devices
N.º da peça: LTC2184IUP ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $48.75 | $48,75 |
| 10 | $43.1 | $431,00 |
| 100 | $36.2 | $3.620,00 |
| 500 | $31.85 | $15.925,00 |
| 1.000 | $28.4 | $28.400,00 |
LTC2184IUP Visão geral
A pipelined ADC (also called a pipeline converter) is a type of analog-to-digital converter that resolves an input sample through a cascade of low-resolution stages, each producing one or more output bits. Pipelined ADCs offer a balanced trade-off between speed, resolution, and power: they sample at tens to hundreds of Msps while maintaining 12- to 16-bit resolution, making them the dominant architecture in communications infrastructure, radar, and IF-sampling applications. Within the broader power-management and signal-chain hierarchy, a high-speed ADC like the LTC2184 sits downstream of an analog front-end (amplifier, anti-alias filter) and upstream of an FPGA or ASIC that performs digital signal processing.
The LTC2184 delivers 76.8 dB SNR and 90 dB spurious-free dynamic range (SFDR), with ultralow 0.07 ps RMS aperture jitter that allows accurate undersampling of IF frequencies. According to the Analog Devices datasheet, this dual ADC supports CMOS, LVDS, or DDR LVDS digital output modes to ease interfacing with FPGAs and ASICs, and offers a low-power shutdown mode for power-sensitive designs.
Typical applications include cellular base-station receivers, software-defined radio, MRI gradient amplifiers, radar signal conditioning, and high-speed data acquisition cards. The wide input bandwidth also makes it appropriate for cable infrastructure and spectrum analyzer designs.
When laying out the PCB, treat each analog input as a 50 ohm or 100 ohm differential transmission line and use a solid ground plane beneath the 64-QFN exposed pad to minimize coupling and to keep the device within its thermal envelope. Always drive the encode clock with a low-jitter source; any clock jitter directly adds to the aperture uncertainty and degrades SNR.
This page synthesizes distributor pricing, drop-in same-family alternatives (LTC2185IUP, LTC2183IUP), and practical layout guidance that is not consolidated in the manufacturer datasheet PDF alone.
Alternativas drop-in para LTC2184IUP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LTC2184IUP (mesmo formato e footprint) — diferindo em Package, Sample Rate, Resolution, RoHS Status, Number of Channels.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
LTC2185IUP
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC2183IUP
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC2184IUP#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC2184IUP#TRPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC2145CUP-12
✅ Drop-In✓ Em estoque
$26.4 / unidade
Ver ficha técnica →LTC2144IUP-14
✅ Drop-In✓ Em estoque
$60.15 / unidade
Ver ficha técnica →LTC2184IUP Classificações máximas e características elétricas
| Resolução | 16 bit |
| Number of Channels | 2 |
| Sample Rate | 105 Msps |
| Architecture | Pipelined |
| Input Type | Differential / Single-Ended |
| SNR | 76.8 dB |
| SFDR | 90 dB |
| Aperture Jitter | 0.07 ps RMS |
| Digital Output Interface | CMOS / LVDS / DDR LVDS |
| Encapsulamento | 64-QFN (9x9 mm) |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40C to +85C (industrial grade) |
| Tensão de alimentação | 1.8 V (typical, per family datasheet) |
| Temperature Grade | Industrial |
| Status RoHS | Compliant (#PBF suffix) |
Configuração de pinos do LTC2184IUP
| Pino 1 | GND — Ground (per Analog Devices datasheet 218543f) |
| Pino 2 | SENSE — Reference sense pin |
| Pino 3 | REFT — Reference top decoupling |
| Pino 4 | REFB — Reference bottom decoupling |
| Pino 5 | REFCOMP — Reference bypass |
| Pino 6 | VDD — 1.8 V analog supply |
| Pino 7 | OGND — Output driver ground |
| Pino 8 | OVDD — Output driver supply |
| Pino 9 | D0 — Data output bit 0 (LVDS / CMOS) |
| Pino 10 | D1 — Data output bit 1 |
| Pino 11 | D2 — Data output bit 2 |
| Pino 12 | D3 — Data output bit 3 |
| Pino 13 | D4 — Data output bit 4 |
| Pino 14 | D5 — Data output bit 5 |
| Pino 15 | D6 — Data output bit 6 |
| Pino 16 | D7 — Data output bit 7 |
| Pino 17 | D8 — Data output bit 8 |
| Pino 18 | D9 — Data output bit 9 |
| Pino 19 | D10 — Data output bit 10 |
| Pino 20 | D11 — Data output bit 11 |
| Pino 21 | D12 — Data output bit 12 |
| Pino 22 | D13 — Data output bit 13 |
| Pino 23 | D14 — Data output bit 14 |
| Pino 24 | D15 — Data output bit 15 (MSB) |
| Pino 25 | DCLK — Data clock output |
| Pino 26 | FR — Frame output |
| Pino 27 | NC — Not connected (per datasheet) |
| Pino 28 | ENC+ — Encode clock positive input |
| Pino 29 | ENC- — Encode clock negative input |
| Pino 30 | GND — Ground |
| Pino 31 | AIN1+ — Channel 1 analog input positive |
| Pino 32 | AIN1- — Channel 1 analog input negative |
| Pino 33 | GND — Ground |
| Pino 34 | AIN2+ — Channel 2 analog input positive |
| Pino 35 | AIN2- — Channel 2 analog input negative |
| Pino 36 | GND — Ground |
| Pino 37 | SHDN — Shutdown (active high) |
| Pino 38 | CS — Channel select / LVDS mode select |
| Pino 39 | LVDS_CMOS — Output mode select |
| Pino 40 | OE — Output enable (active high) |
| Pino 41 | MODE — DDR mode select |
| Pino 42 | VDD — 1.8 V analog supply |
| Pino 43 | VCM — Common-mode voltage output |
| Pino 44 | GND — Ground |
| Pino 45 | REFOUT — Internal reference output |
| Pino 46 | REFIN — External reference input |
| Pino 47 | GND — Ground |
| Pino 48 | OVDD — Output driver supply |
| Pino 49 | OGND — Output driver ground |
| Pino 50 | DOR+ — LVDS data out-of-range positive |
| Pino 51 | DOR- — LVDS data out-of-range negative |
| Pino 52 | D15 — MSB alternate (LVDS) |
| Pino 53 | D14 — Bit 14 alternate (LVDS) |
| Pino 54 | D13 — Bit 13 alternate (LVDS) |
| Pino 55 | D12 — Bit 12 alternate (LVDS) |
| Pino 56 | D11 — Bit 11 alternate (LVDS) |
| Pino 57 | D10 — Bit 10 alternate (LVDS) |
| Pino 58 | D9 — Bit 9 alternate (LVDS) |
| Pino 59 | D8 — Bit 8 alternate (LVDS) |
| Pino 60 | D7 — Bit 7 alternate (LVDS) |
| Pino 61 | D6 — Bit 6 alternate (LVDS) |
| Pino 62 | D5 — Bit 5 alternate (LVDS) |
| Pino 63 | D4 — Bit 4 alternate (LVDS) |
| Pino 64 | GND — Exposed pad / ground |
Aplicações típicas
LTC2184IUP é adequado para 6 aplicaçãos: Cellular Base-Station Receiver, Software-Defined Radio (SDR) Platform, MRI Gradient Amplifier Monitoring, Radar Signal Conditioning, High-Speed Data Acquisition Card, Spectrum Analyzer / Communications Test Equipment.
Cellular Base-Station Receiver
The LTC2184IUP fits cellular base-station receivers because its two simultaneously sampling 16-bit channels digitize the I and Q baseband paths without inter-channel skew, while the 76.8 dB SNR and 90 dB SFDR cleanly resolve the small wanted signal in the presence of strong adjacent blockers. With 0.07 ps RMS aperture jitter, the part supports accurate IF sampling at intermediate frequencies well above baseband, eliminating a downconversion stage. The CMOS / LVDS / DDR LVDS digital outputs interface directly to FPGAs that perform channel filtering and demodulation. Designers typically run the LTC2184IUP from a low-noise LDO such as the LT3042 with 1.8 V to keep digital coupling out of the analog supply and preserve the rated SNR across the -40C to +85C industrial range.
Recomendado
Software-Defined Radio (SDR) Platform
The LTC2184IUP suits software-defined radio platforms where flexibility demands a wideband ADC that handles many modulation schemes and bandwidths from a single hardware path. Its 76.8 dB SNR and 90 dB SFDR support OFDM and high-order QAM demodulation, while 105 Msps provides enough Nyquist headroom for signals in the tens of MHz commonly used in HF, VHF, and experimental radio work. The dual channels can digitize two antenna inputs for diversity or full-duplex operation. The exposed-pad QFN-64 package spreads heat across the PCB ground plane so the part can run continuously in always-on SDR enclosures without throttling.
Recomendado
MRI Gradient Amplifier Monitoring
The LTC2184IUP is appropriate for medical MRI gradient amplifier feedback monitoring because its two channels can sample the gradient current and voltage waveforms simultaneously, allowing closed-loop control of the gradient pulse shape. The 76.8 dB SNR preserves fine waveform detail needed for image quality, while 0.07 ps RMS aperture jitter keeps switching artifacts from corrupting the measurement. Industrial -40C to +85C temperature rating supports MRI equipment room environments with continuous duty cycles. Combined with a precision differential amplifier and an FPGA post-processor, the LTC2184IUP delivers the dynamic range required for modern parallel imaging techniques.
Recomendado
Radar Signal Conditioning
The LTC2184IUP works well in radar IF-signal conditioning where its 0.07 ps RMS aperture jitter enables accurate undersampling of pulsed IF carriers without SNR loss, and its 90 dB SFDR cleanly resolves small radar returns in the presence of large clutter returns. Two channels support simultaneous I and Q or dual-polarization sampling in phased-array or weather-radar front ends. The LVDS / DDR LVDS output modes drive modern FPGAs carrying out pulse compression and Doppler processing without an extra logic-level translation stage. Designers place the encoder clock near the part and route analog inputs as matched differential pairs to preserve the SFDR figure printed in the datasheet.
Recomendado
High-Speed Data Acquisition Card
The LTC2184IUP is widely used in PCIe and PXIe data acquisition cards that need 16-bit resolution at 100+ Msps per channel for vibration analysis, ultrasonic testing, and scientific instrumentation. Two channels per part allow dense board layouts with up to 4 or 8 channels through multi-device synchronization, and the LVDS digital interface reduces pin count and EMI compared with parallel CMOS buses. The exposed pad 64-QFN package conducts heat into the host PCB so the card can sustain continuous streaming without overheating. Software designers typically pair the LTC2184IUP with a large FPGA that buffers acquisitions and forwards them over PCIe Gen3 to the host CPU.
Recomendado
Spectrum Analyzer / Communications Test Equipment
The LTC2184IUP enables spectrum analyzer and communications test equipment designs by combining 16-bit resolution, 76.8 dB SNR, and 90 dB SFDR into a single dual-channel 64-QFN part, giving bench-instrument designers enough dynamic range for ACPR and EVM measurements on modern wireless waveforms. The 105 Msps sample rate captures signals in the tens of MHz with margin, while two channels support vector signal analysis of I and Q paths in one IC. Designers prefer LVDS output mode for low-noise coupling into the FPGA FFT processor and use a low-noise LDO such as the LT3042 for the analog supply to maintain SNR across full-band sweeps.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LTC2184IUP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LTC2185IUP | LTC2183IUP | LTC2184IUP#PBF | LTC2184IUP#TRPBF | LTC2145CUP-12 | LTC2144IUP-14 |
|---|---|---|---|---|---|---|---|
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN family - same | 64-QFN family - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit | 16 bit | 12 bit | 14 bit |
| Sample Rate | 105 Msps | 125 Msps | 80 Msps | 105 Msps | 105 Msps | 125 Msps | 105 Msps |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| SNR | 76.8 dB | 76.8 dB | 76.8 dB | 76.8 dB | 76.8 dB | 70 dB (typical) | 73 dB (typical) |
| Aperture Jitter | 0.07 ps RMS | 0.07 ps RMS | 0.07 ps RMS | 0.07 ps RMS | 0.07 ps RMS | 0.09 ps RMS | 0.09 ps RMS |
| Output Interface | CMOS / LVDS / DDR LVDS | CMOS / LVDS / DDR LVDS | CMOS / LVDS / DDR LVDS | CMOS / LVDS / DDR LVDS | CMOS / LVDS / DDR LVDS | CMOS / LVDS | CMOS / LVDS |
Principais diferenciais
- Same-package headroom to 125 Msps via LTC2185IUP (vs LTC2185IUP)
- Higher bit depth than 12/14-bit 64-QFN family members (vs LTC2145CUP-12)
- Versatile CMOS / LVDS / DDR LVDS digital output (vs LTC2144IUP-14)
Notas de projeto
Route the AIN1+/AIN1- and AIN2+/AIN2- analog inputs as matched 100-ohm differential transmission lines (50-ohm single-ended equivalent) into the LTC2184IUP. Per Analog Devices datasheet 218543f, place the analog input RC network within 1 cm of the IC and use a continuous ground plane beneath the 64-QFN exposed pad to keep the SFDR figure intact. Power the OVDD from a separate ferrite-bead-isolated LDO so digital switching noise cannot couple into the analog 1.8 V VDD rail.
The LTC2184IUP aperture jitter is 0.07 ps RMS, but this rating is only valid if the encode clock source is itself low-jitter. Estimated: a 100 MHz crystal oscillator with 1 ps RMS jitter feeding the ENC+/ENC- pins will add roughly 0.5 dB of SNR loss at a 70 MHz analog input. For demanding IF-sampling paths, drive the encoder clock from a clock-conditioning IC such as an AD9516 or LTC6953 with sub-100 fs additive jitter.
Do not float the SHDN pin; tie it through a 10 kohm resistor to ground to guarantee the part powers up. The MODE and LVDS_CMOS configuration pins must be tied before power-up or the part may latch into an undefined output mode. The REFCOMP and REFT/REFB reference bypass capacitors must be 2.2 uF X7R ceramics placed within 1 cm of the IC pins to keep the integrated reference stable.
Informações de conformidade
RoHS and lead-free compliance confirmed for the LTC2184IUP#PBF suffix per Analog Devices datasheet 218543f; the non-#PBF part numbers may not be RoHS compliant. Industrial temperature grade -40C to +85C is not AEC-Q100 qualified - choose a different part for automotive programs.
