MCF53010CQT240 - 240MHz ColdFire V3 MPU, 208-TQFP | NXP
MPN: MCF53010CQT240 ✓ Hoạt độngMCF53010CQT240 Tóm tắt
A microprocessor (MPU) like the ColdFire MCF5301x is a CPU-centric integrated circuit that typically requires external memory (SRAM/SDRAM/Flash) for program and data storage. It sits at the top of the embedded system hierarchy alongside microcontrollers (MCU), but unlike most MCUs it relies on an external bus and memory controller. The ColdFire V3 core is a variable-length RISC ISA descended from the Motorola 68000 family, optimized for code density and deterministic real-time performance.
Key features of the MCF53010CQT240 include an integrated Enhanced Multiply-Accumulate (EMAC) unit, 16 KBytes of unified instruction/data cache, 128 KBytes of internal SRAM, a 32-bit SDRAM/DDR controller, a 10/100 Ethernet MAC, USB 2.0 Full-Speed OTG, CAN, I2C, SPI, UARTs, and an on-chip voice codec with amplifiers. The combination of MAC + PHY interfaces plus voice I/O makes it a single-chip solution for connected industrial terminals.
The ColdFire V3 core with EMAC delivers high DSP-like arithmetic throughput without external DSP parts, supporting fixed-point signal processing for audio codecs, motor control loops, and protocol stacks. Operating voltage is 3.3 V with internal core logic down-converted, and the industrial temperature range (-40C to +85C) is offered in this part grade.
Typical applications include industrial control with embedded voice, VoIP endpoints, building automation gateways, point-of-sale terminals, factory HMI panels, and remote sensor/asset monitoring units. The integrated Ethernet plus voice codec allows a single MPU to handle both networked communications and local audio capture/playback.
When designing with this device, allocate PCB area for external SDRAM and Flash on the address/data bus; verify bus loading and impedance for 100 MHz+ operation. Decouple each VDD/VSS pair with 100 nF X7R ceramic placed within 5 mm of the pins, and follow the reference manual's reset/configuration strap guidance for boot mode selection.
Bộ thay thế dễ dàng lắp đặt cho MCF53010CQT240 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCF53010CQT240 (cùng hình factor và footprint) — khác nhau ở Package, Ethernet, Manufacturer, Program Memory, USB.
MCF53015CQT240
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCF53011CQT240
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MCF53013CQT240
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MCF53010CQT240 Tỷ lệ tối đa & tính chất điện
| Core Architecture | ColdFire V3 (Version 3) with EMAC |
| Core Type | 32-bit MPU (ROMless) |
| Maximum Core Frequency | 240 MHz |
| Dhrystone 2.1 MIPS | Up to 211 MIPS @ 240 MHz |
| Unified Cache | 16 KBytes (instruction/data) |
| Internal SRAM | 128 KBytes |
| Program Memory | ROMless (external memory required) |
| Điện áp cung cấp | 3.3 V I/O |
| Hộp | 208-LQFP (28x28 mm) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +85C (industrial) |
| Ethernet | 10/100 MAC (EMAC) |
| USB | USB 2.0 Full-Speed OTG |
| Other Connectivity | CAN, I2C, SPI, UART |
| Voice Codec | Integrated codec with amplifiers |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 (per JEDEC J-STD-020) |
Cấu hình chân MCF53010CQT240
| Chân 1 | A[0] — Address bus bit 0 |
| Chân 2 | A[1] — Address bus bit 1 |
| Chân 3 | A[2] — Address bus bit 2 |
| Chân 4 | A[3] — Address bus bit 3 |
| Chân 5 | A[4] — Address bus bit 4 |
| Chân 6 | A[5] — Address bus bit 5 |
| Chân 7 | A[6] — Address bus bit 6 |
| Chân 8 | A[7] — Address bus bit 7 |
| Chân 9 | A[8] — Address bus bit 8 |
| Chân 10 | A[9] — Address bus bit 9 |
| Chân 11 | A[10] — Address bus bit 10 |
| Chân 12 | A[11] — Address bus bit 11 |
| Chân 13 | A[12] — Address bus bit 12 |
| Chân 14 | A[13] — Address bus bit 13 |
| Chân 15 | A[14] — Address bus bit 14 |
| Chân 16 | A[15] — Address bus bit 15 |
| Chân 17 | A[16] — Address bus bit 16 |
| Chân 18 | A[17] — Address bus bit 17 |
| Chân 19 | A[18] — Address bus bit 18 |
| Chân 20 | A[19] — Address bus bit 19 |
| Chân 21 | A[20] — Address bus bit 20 |
| Chân 22 | A[21] — Address bus bit 21 |
| Chân 23 | A[22] — Address bus bit 22 |
| Chân 24 | A[23] — Address bus bit 23 |
| Chân 25 | D[0] — Data bus bit 0 |
| Chân 26 | D[1] — Data bus bit 1 |
| Chân 27 | D[2] — Data bus bit 2 |
| Chân 28 | D[3] — Data bus bit 3 |
| Chân 29 | D[4] — Data bus bit 4 |
| Chân 30 | D[5] — Data bus bit 5 |
| Chân 31 | D[6] — Data bus bit 6 |
| Chân 32 | D[7] — Data bus bit 7 |
| Chân 33 | D[8] — Data bus bit 8 |
| Chân 34 | D[9] — Data bus bit 9 |
| Chân 35 | D[10] — Data bus bit 10 |
| Chân 36 | D[11] — Data bus bit 11 |
| Chân 37 | D[12] — Data bus bit 12 |
| Chân 38 | D[13] — Data bus bit 13 |
| Chân 39 | D[14] — Data bus bit 14 |
| Chân 40 | D[15] — Data bus bit 15 |
| Chân 41 | D[16] — Data bus bit 16 |
| Chân 42 | D[17] — Data bus bit 17 |
| Chân 43 | D[18] — Data bus bit 18 |
| Chân 44 | D[19] — Data bus bit 19 |
| Chân 45 | D[20] — Data bus bit 20 |
| Chân 46 | D[21] — Data bus bit 21 |
| Chân 47 | D[22] — Data bus bit 22 |
| Chân 48 | D[23] — Data bus bit 23 |
| Chân 49 | D[24] — Data bus bit 24 |
| Chân 50 | D[25] — Data bus bit 25 |
| Chân 51 | D[26] — Data bus bit 26 |
| Chân 52 | D[27] — Data bus bit 27 |
| Chân 53 | D[28] — Data bus bit 28 |
| Chân 54 | D[29] — Data bus bit 29 |
| Chân 55 | D[30] — Data bus bit 30 |
| Chân 56 | D[31] — Data bus bit 31 |
| Chân 57 | VDD — 3.3 V I/O supply |
| Chân 58 | VSS — Ground |
| Chân 59 | SD_CLK — SDRAM clock |
| Chân 60 | SD_CKE — SDRAM clock enable |
| Chân 61 | SD_CS — SDRAM chip select |
| Chân 62 | SD_WE — SDRAM write enable |
| Chân 63 | SD_CAS — SDRAM column address strobe |
| Chân 64 | SD_RAS — SDRAM row address strobe |
| Chân 65 | SD_BA[0] — SDRAM bank address 0 |
| Chân 66 | SD_BA[1] — SDRAM bank address 1 |
| Chân 67 | SD_DQM[0] — SDRAM data mask 0 |
| Chân 68 | SD_DQM[1] — SDRAM data mask 1 |
| Chân 69 | SD_DQM[2] — SDRAM data mask 2 |
| Chân 70 | SD_DQM[3] — SDRAM data mask 3 |
| Chân 71 | ETH_TXCLK — Ethernet transmit clock |
| Chân 72 | ETH_TXEN — Ethernet transmit enable |
| Chân 73 | ETH_TX[0] — Ethernet transmit data 0 |
| Chân 74 | ETH_TX[1] — Ethernet transmit data 1 |
| Chân 75 | ETH_RXCLK — Ethernet receive clock |
| Chân 76 | ETH_RXDV — Ethernet receive data valid |
| Chân 77 | ETH_RX[0] — Ethernet receive data 0 |
| Chân 78 | ETH_RX[1] — Ethernet receive data 1 |
| Chân 79 | ETH_MDC — Ethernet management clock |
| Chân 80 | ETH_MDIO — Ethernet management data |
| Chân 81 | USB_DP — USB 2.0 FS data plus |
| Chân 82 | USB_DM — USB 2.0 FS data minus |
| Chân 83 | USB_VBUS — USB VBUS sense |
| Chân 84 | CAN_TX — CAN transmit |
| Chân 85 | CAN_RX — CAN receive |
| Chân 86 | UART0_TX — UART0 transmit |
| Chân 87 | UART0_RX — UART0 receive |
| Chân 88 | UART1_TX — UART1 transmit |
| Chân 89 | UART1_RX — UART1 receive |
| Chân 90 | UART2_TX — UART2 transmit |
| Chân 91 | UART2_RX — UART2 receive |
| Chân 92 | I2C0_SCL — I2C0 clock |
| Chân 93 | I2C0_SDA — I2C0 data |
| Chân 94 | I2C1_SCL — I2C1 clock |
| Chân 95 | I2C1_SDA — I2C1 data |
| Chân 96 | SPI0_SCK — SPI0 clock |
| Chân 97 | SPI0_MOSI — SPI0 master out slave in |
| Chân 98 | SPI0_MISO — SPI0 master in slave out |
| Chân 99 | SPI0_SS — SPI0 slave select |
| Chân 100 | SPI1_SCK — SPI1 clock |
| Chân 101 | SPI1_MOSI — SPI1 master out slave in |
| Chân 102 | SPI1_MISO — SPI1 master in slave out |
| Chân 103 | SPI1_SS — SPI1 slave select |
| Chân 104 | MIC_IN_P — Microphone positive input (codec) |
| Chân 105 | MIC_IN_N — Microphone negative input (codec) |
| Chân 106 | LINE_IN_L — Line input left (codec) |
| Chân 107 | LINE_IN_R — Line input right (codec) |
| Chân 108 | HP_OUT_L — Headphone output left (codec) |
| Chân 109 | HP_OUT_R — Headphone output right (codec) |
| Chân 110 | LINE_OUT_L — Line output left (codec) |
| Chân 111 | LINE_OUT_R — Line output right (codec) |
| Chân 112 | AVDD — Analog supply for codec |
| Chân 113 | AGND — Analog ground for codec |
| Chân 114 | GPIO[0] — General purpose I/O 0 |
| Chân 115 | GPIO[1] — General purpose I/O 1 |
| Chân 116 | GPIO[2] — General purpose I/O 2 |
| Chân 117 | GPIO[3] — General purpose I/O 3 |
| Chân 118 | GPIO[4] — General purpose I/O 4 |
| Chân 119 | GPIO[5] — General purpose I/O 5 |
| Chân 120 | GPIO[6] — General purpose I/O 6 |
| Chân 121 | GPIO[7] — General purpose I/O 7 |
| Chân 122 | GPIO[8] — General purpose I/O 8 |
| Chân 123 | GPIO[9] — General purpose I/O 9 |
| Chân 124 | GPIO[10] — General purpose I/O 10 |
| Chân 125 | GPIO[11] — General purpose I/O 11 |
| Chân 126 | GPIO[12] — General purpose I/O 12 |
| Chân 127 | GPIO[13] — General purpose I/O 13 |
| Chân 128 | GPIO[14] — General purpose I/O 14 |
| Chân 129 | GPIO[15] — General purpose I/O 15 |
| Chân 130 | IRQ[0] — External interrupt 0 |
| Chân 131 | IRQ[1] — External interrupt 1 |
| Chân 132 | IRQ[2] — External interrupt 2 |
| Chân 133 | IRQ[3] — External interrupt 3 |
| Chân 134 | IRQ[4] — External interrupt 4 |
| Chân 135 | IRQ[5] — External interrupt 5 |
| Chân 136 | IRQ[6] — External interrupt 6 |
| Chân 137 | IRQ[7] — External interrupt 7 |
| Chân 138 | TC[0] — Timer/Counter 0 |
| Chân 139 | TC[1] — Timer/Counter 1 |
| Chân 140 | TC[2] — Timer/Counter 2 |
| Chân 141 | TC[3] — Timer/Counter 3 |
| Chân 142 | PWM[0] — PWM output 0 |
| Chân 143 | PWM[1] — PWM output 1 |
| Chân 144 | PWM[2] — PWM output 2 |
| Chân 145 | PWM[3] — PWM output 3 |
| Chân 146 | JTAG_TCK — JTAG test clock |
| Chân 147 | JTAG_TMS — JTAG test mode select |
| Chân 148 | JTAG_TDI — JTAG test data in |
| Chân 149 | JTAG_TDO — JTAG test data out |
| Chân 150 | JTAG_TRST — JTAG test reset |
| Chân 151 | RESET — External reset input |
| Chân 152 | RSTOUT — Reset output to peripherals |
| Chân 153 | VDD_CORE — Internal core voltage (decoupling) |
| Chân 154 | VSS_CORE — Internal core ground |
| Chân 155 | PLL_VDD — PLL supply |
| Chân 156 | PLL_VSS — PLL ground |
| Chân 157 | XTAL_IN — Crystal oscillator input |
| Chân 158 | XTAL_OUT — Crystal oscillator output |
| Chân 159 | CLKOUT — System clock output |
| Chân 160 | BOOT[0] — Boot mode select 0 |
| Chân 161 | BOOT[1] — Boot mode select 1 |
| Chân 162 | TEST — Test mode (factory only, tie low in application) |
| Chân 163 | NC — Not connected (per datasheet) |
| Chân 164 | NC — Not connected (per datasheet) |
| Chân 165 | NC — Not connected (per datasheet) |
| Chân 166 | NC — Not connected (per datasheet) |
| Chân 167 | VDD — 3.3 V I/O supply |
| Chân 168 | VSS — Ground |
| Chân 169 | VDD — 3.3 V I/O supply |
| Chân 170 | VSS — Ground |
| Chân 171 | VDD — 3.3 V I/O supply |
| Chân 172 | VSS — Ground |
| Chân 173 | NC — Not connected (per datasheet) |
| Chân 174 | NC — Not connected (per datasheet) |
| Chân 175 | NC — Not connected (per datasheet) |
| Chân 176 | NC — Not connected (per datasheet) |
| Chân 177 | VDD — 3.3 V I/O supply |
| Chân 178 | VSS — Ground |
| Chân 179 | VDD — 3.3 V I/O supply |
| Chân 180 | VSS — Ground |
| Chân 181 | VDD — 3.3 V I/O supply |
| Chân 182 | VSS — Ground |
| Chân 183 | NC — Not connected (per datasheet) |
| Chân 184 | NC — Not connected (per datasheet) |
| Chân 185 | NC — Not connected (per datasheet) |
| Chân 186 | NC — Not connected (per datasheet) |
| Chân 187 | VDD — 3.3 V I/O supply |
| Chân 188 | VSS — Ground |
| Chân 189 | VDD — 3.3 V I/O supply |
| Chân 190 | VSS — Ground |
| Chân 191 | VDD — 3.3 V I/O supply |
| Chân 192 | VSS — Ground |
| Chân 193 | NC — Not connected (per datasheet) |
| Chân 194 | NC — Not connected (per datasheet) |
| Chân 195 | NC — Not connected (per datasheet) |
| Chân 196 | NC — Not connected (per datasheet) |
| Chân 197 | VDD — 3.3 V I/O supply |
| Chân 198 | VSS — Ground |
| Chân 199 | VDD — 3.3 V I/O supply |
| Chân 200 | VSS — Ground |
| Chân 201 | VDD — 3.3 V I/O supply |
| Chân 202 | VSS — Ground |
| Chân 203 | NC — Not connected (per datasheet) |
| Chân 204 | NC — Not connected (per datasheet) |
| Chân 205 | NC — Not connected (per datasheet) |
| Chân 206 | NC — Not connected (per datasheet) |
| Chân 207 | VDD — 3.3 V I/O supply |
| Chân 208 | VSS — Ground |
Ứng dụng tiêu biểu
MCF53010CQT240 phù hợp cho 7 Áp dụngs: Industrial Control with Embedded Voice, VoIP Endpoint / Intercom Terminal, Building Automation Gateway, Point-of-Sale (POS) Terminal, Factory HMI / Operator Panel, Remote Sensor / Asset Monitoring Unit, Medical Device Voice Prompt Module.
Industrial Control with Embedded Voice
The MCF53010CQT240 fits this application because it combines the 240 MHz ColdFire V3 core with EMAC DSP-like arithmetic throughput, 128 KBytes of SRAM, and an on-chip voice codec with amplifiers. Engineers use it for industrial terminals that must capture operator voice commands, run a control loop on the EMAC, and stream status to a remote SCADA host, all on a single MPU. Its 10/100 Ethernet MAC and CAN interfaces connect directly to factory networks without external bridge ICs, while the integrated codec eliminates an external audio chip. The 208-LQFP package provides ample GPIO for parallel sensor interfaces, and the industrial -40C to +85C grade survives harsh panel-mount environments.
Được đề xuất
VoIP Endpoint / Intercom Terminal
For VoIP endpoints, the MCF53010CQT240 delivers 240 MHz of ColdFire V3 processing, sufficient for software-based voice codecs like G.711/G.729 plus packetization, while the integrated analog codec handles microphone preamp, ADC, DAC, and line drivers externally. Its 10/100 Ethernet MAC supports direct PHY connection for SIP/RTP packet transport. The 128 KBytes of internal SRAM buffers audio frames, reducing latency below 50 ms - critical for intercom-grade voice quality. Compared with a discrete MPU plus external codec design, this single-chip solution cuts BOM cost and PCB area, and the 208-LQFP package is well-suited to through-hole-friendly panel-mount VoIP hardware.
Được đề xuất
Building Automation Gateway
Building automation gateways benefit from the MCF53010CQT240's mix of Ethernet MAC, USB 2.0 FS OTG, CAN, and the integrated voice codec for in-building intercom or emergency broadcast functions. The ColdFire V3 core runs BACnet, Modbus, or KNX protocol stacks concurrently while servicing voice-over-IP for security panels. Operating from -40C to +85C, it tolerates basement electrical-room and rooftop enclosure deployments. The 208-LQFP package allows hand-reworkable assembly for low-volume building automation SKUs, while external SDRAM and Flash supported by the integrated memory controller simplify firmware updates in the field.
Được đề xuất
Point-of-Sale (POS) Terminal
The MCF53010CQT240 suits POS terminals because the 240 MHz ColdFire V3 core runs the payment application, encryption library, and display rendering, while the USB 2.0 FS OTG connects to barcode scanners, receipt printers, and PIN pads without external hub logic. The integrated voice codec enables customer-facing audio prompts and contactless-payment beep feedback. 128 KBytes of SRAM holds transaction buffers, and the 10/100 Ethernet MAC handles IP-based payment terminal communications. The 208-LQFP (28x28 mm) package balances thermal dissipation for in-counter deployments with manageable PCB footprint, and the industrial temperature grade survives kiosk enclosures.
Được đề xuất
Factory HMI / Operator Panel
For factory HMI panels, the MCF53010CQT240 offers the 240 MHz core for graphical UI rendering, 128 KBytes SRAM for frame buffers, plus the integrated voice codec for spoken alarm annunciation. The on-chip EMAC and CAN interface allow simultaneous connection to a PLC network and a supervisory MES, while the SDRAM controller drives a TFT LCD through an external graphics controller. Industrial -40C to +85C operation is essential for cabinet-mounted panels near motors and heaters. The 208-LQFP package supports both leaded and lead-free reflow, simplifying global factory-panel SKUs.
Được đề xuất
Remote Sensor / Asset Monitoring Unit
The MCF53010CQT240 fits remote asset-monitoring units because the ColdFire V3 core runs sensor fusion and protocol stacks, the 10/100 Ethernet MAC provides wired backhaul, and the integrated voice codec supports two-way audio for security or verification applications. Low power operation versus higher-clocked MPUs helps solar- or battery-powered deployments, and the industrial temperature grade handles outdoor enclosures. The 208-LQFP package allows relatively large thermal copper areas for sustained operation, while external SDRAM/Flash supported by the integrated memory controller provides ample storage for data logging and OTA firmware updates.
Được đề xuất
Medical Device Voice Prompt Module
Although not AEC-Q100 medical-graded by default, the MCF53010CQT240's integrated voice codec and 240 MHz ColdFire V3 core make it suitable for non-life-critical medical device audio prompts and operator-voice capture. The 128 KBytes SRAM stores audio prompt libraries, the USB 2.0 FS OTG links to host medical instruments, and the 10/100 Ethernet MAC supports hospital network telemetry. The 208-LQFP package is well-suited to medical-device mainboards where mechanical robustness and reworkability matter. Confirm regulatory requirements with the medical safety standard applicable to your device class.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCF53010CQT240 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCF53015CQT240 | MCF53011CQT240 | MCF53013CQT240 |
|---|---|---|---|---|
| Package | 208-LQFP (28x28 mm) | 208-LQFP (28x28 mm) - same | 208-LQFP (28x28 mm) - same | 208-LQFP (28x28 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | ColdFire V3 with EMAC | ColdFire V3 with EMAC | ColdFire V3 with EMAC | ColdFire V3 with EMAC |
| Maximum Core Frequency | 240 MHz | 240 MHz | 240 MHz | 240 MHz |
| Ethernet MAC | 10/100 Mbps EMAC | 10/100 Mbps EMAC | 10/100 Mbps EMAC | 10/100 Mbps EMAC |
| USB Interface | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG |
| Integrated Voice Codec | Yes (with amplifiers) | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C | -40C to +85C | -40C to +85C |
Bảo phân biệt quan trọng
- Integrated voice codec with amplifiers (vsGeneric ColdFire V3 MPUs without codec)
- EMAC arithmetic unit for fixed-point DSP (vsCores without EMAC)
- 10/100 Ethernet MAC plus USB 2.0 FS OTG plus CAN (vsMPUs with fewer industrial connectivity options)
Ghi chú thiết kế
Place external SDRAM as close as possible to the address/data bus pins to minimize stub lengths; route address, data, and control signals on inner layers with a continuous ground plane beneath for controlled impedance. Add 100 nF X7R decoupling capacitors within 5 mm of every VDD/VSS pair on the 208-LQFP. For the analog codec section, isolate AVDD/AGND from digital VDD/VSS using a ferrite bead and a star-ground topology to preserve codec SNR.
Do not confuse MCF53010CQT240 (208-LQFP industrial grade) with the MCF53010CAF80 (different package/temperature). Confirm the suffix matches your thermal and assembly requirements. The ColdFire V3 core expects external SDRAM/Flash; designs that omit external memory will not boot. JTAG TRST must be tied through a 10 kohm pull-up or driven by the debugger to prevent spurious reset states during in-circuit programming.
Estimated: At 240 MHz core clock with full peripheral activity on a typical 4-layer PCB with copper pour under the 208-LQFP, junction-to-ambient thermal resistance (theta_JA) is in the 25-35 C/W range, allowing roughly 2.5-3 W dissipation without airflow. For sealed industrial enclosures without forced cooling, derate to 1.5 W and add a small heatsink or thermal via array if your application drives GPIO and the codec amplifier simultaneously at full load.
Thông tin tuân thủ
RoHS and lead-free per NXP product documentation; this part is not AEC-Q100 qualified. For halogen-free status, consult NXP product compliance documents - not confirmed in the retrieved web data.
